Starline a64 operating instructions autostart

The Starline alarm system is the latest generation security system that meets all standards and requirements for car security. If the system was installed by professionals, it also allows you to activate automatic engine start.

It is important to understand that not all motorists are familiar with this function, so not everyone can set it up on their own. In this article we will tell you in detail how to correctly enable starline autorun.

Specifications

Characteristics of the alarm for the Starline A64 2CAN Slave or Dialog car:

Data transmission when sending and receiving commands to the main control unit is carried out at a frequency of 433.05 - 434.70 MHz.
The number of radio channels over which data can be transmitted is 128.
When the key fob operates in the mode of sending signals and commands, the maximum range of the device is 800 meters. When receiving signals from the microprocessor module, the operating radius will be increased to two kilometers. But in fact, achieving such indicators is only possible in open areas, where there is practically no interference.
The operating range of the spare key fob is no more than fifteen meters.
The tilt and shock controller belongs to the class of integral three-axis sensors.
The temperature range at which the anti-theft complex optimally performs all options is from -50 to +85 degrees.
The voltage required to power the Starline A64 ranges from 9 to 18 volts. It is best to install alarms on cars and SUVs, as well as minibuses. But installation of car alarms is also allowed on motorcycles.
The amount of current that the anti-theft complex consumes when the protection mode is activated is 23 mA.
The current parameter at the output of the alarm siren will be no more than 2 amperes.
At the outputs of the electrical lines of the machine's lighting devices, the current value will be no more than 7.5 amperes for each optical device.
To ensure the operation of the main communicator with a display, you will need one AAA battery, rated at 1.5 volts.
To power the spare communicator, one CR2450 class power supply rated at 3 volts is required.

Equipment

Car alarm delivery set:

Service user manual. The documentation describes all the functions and nuances regarding their management.
Warranty card.
Consumer Memo. It indicates all the nuances regarding warranty service and use of the system.
Main communicator. It has a feedback option and is equipped with a display.
Microprocessor device. Supplied in a black plastic case.
One power supply for installation in the main alarm key fob.
Spare pager.
Auxiliary relay with connection block. They are supplied in quantities of three pieces.
One limit switch for mounting on the hood. The kit also contains two self-tapping screws, a special terminal for connecting grounding and diode elements of the IN4007 type.
Antenna adapter.
The main wire is equipped with a plug with 18 contact elements.
Mounting kit of wires for connecting the antenna module, anti-theft complex inputs, CAN interface, as well as a limit switch.
Key to enter service mode.
LED indicator.
Special adapter for connecting additional controllers.

The siren is not included in the Starline A64 package; this device will have to be purchased separately.

Set of basic alarm elements Starline A64

More information about the configuration of the Starline A64 signaling can be found in the video filmed by the Unpacking Auto Products channel.

Key features and functionality

Signaling comfort options:

Possibility of controlling a pre-heating device for a diesel engine.
Automatic adjustment of seats for the driver. Setting this option is only possible if an electronic setting system is available.
Possibility of returning the steering column to its original state. In this case we are talking about folding.
Automatic activation of low-beam optics when the vehicle is moving. You can set the lights to turn on when you release the parking brake lever or press the brake pedal.

Availability of two-way communication. All data about the condition of the car will be transferred to the car owner's key fob.
Dialogue method of signal protection. The use of such encoding prevents the possibility of intelligent electronic hacking. This ensures protection from scanners and code grabbers.
The Starline A64 2CH Slave model supports the control option using a mobile gadget. Installation of the GSM block provides the ability to manage security and service options. Using this device, the consumer's phone can be configured to transmit data about the protection status.
In the 2KAN Slave model for monitoring via GPS channel, the consumer will not have to pay additionally for the service. The user will be able to determine the location of the machine with high accuracy (up to several meters). For monitoring, a special service from the manufacturer Starline is used.
Another feature is that Starline A64 anti-theft systems are equipped with a key fob made in a shock-resistant case. This will ensure its protection from mechanical damage and falls.
Reduced energy consumption. If a consumer leaves the car in a parking lot or garage with the alarm on, the battery will last about two months before running out.
Effective protection against interference.
2KAN Slave models are equipped with a tilt and shock controller. The three-axis integrated controller has the ability to remotely configure and adjust parameters. The device allows you to record the evacuation of the car, as well as its jacking.
Availability of power keys. This ensures hidden and silent operation of the microprocessor unit. Thanks to this feature, it is possible to protect power contacts from possible short circuits.
Availability of built-in 2CH interface. Thanks to this, the consumer will be able to quickly and conveniently, and most importantly safely, install the anti-theft system. It is important that the machine is equipped with a CAN bus.
Use of flexible service channels for data transmission. The consumer can independently configure the control parameters for the light signal, the side mirror folding system, etc.
2Slave. This interface provides the ability to control the machine's protective functions through the use of a standard communicator.

Read also: The angel eyes of the BMW E60 do not light up.
A detailed overview of all the features and capabilities is given in the video of the AutoAudioTsentr channel.

Starline alarm problems and solutions

The engine does not start or stalls after a minute of operation

You can try to fix problems like this; practice shows that this method only helps in 75% of cases:

Go to a specialized service center and ask the technicians to install a bypass module for the standard immobilizer.
Be sure to check that the transponder key is positioned correctly.
Reconnect the autostart control wire, now you can test the autostart function.

Autostart with manual transmission works every other time

Start the engine by turning the key in the ignition and put the car on the handbrake.
Remove the key from the ignition.
Open and close all the doors of the car, and then activate the security function.

Alarm blocks auto start

Drivers claim that this problem can be dealt with simply by resetting the key fob settings. You can do this using these instructions:

Put the car on the parking brake and turn on the ignition.
Press the valet button on the Starline alarm system 10 times.
Now you need to wait for the system to reboot, after which 2 beeps will sound.
Then you should confirm the reset by pressing button 1, then you will see all dimensions blinking 5 times. Now the key fob settings will be reset to factory settings.

If you carefully studied the article, then now you can independently configure autostart on your Starline alarm system. We wish you success!

Advantages and disadvantages

Advantages of Starline A64 anti-theft systems:

System reliability. With proper connection and configuration of all elements, the consumer receives a complete complex that can provide maximum protection for the machine.
High operating radius of the communicator. Even if there is interference in the area, the range of operation of the pager will be quite large.
Ease of installation and configuration. In the technical manual, the manufacturer described all the nuances regarding the installation of signaling elements and setting parameters. An inexperienced consumer, taking into account all the advice, will be able to independently install and configure the system.
Multifunctionality. The alarm system has many useful security and service options.

Communicator. Despite the shock-resistant case, according to reviews, the control buttons on it often fail. You will have to repair and replace the keys.
It may be difficult to configure the alarm if the Slave mode is used.

Operating instructions for StarLine A61 alarm system with auto start

To correctly install and configure the automatic start module for Starline A61 M31, you can use the detailed instructions from the manufacturer. It is also available in pdf format for downloading or viewing.

Good day. I have a question about the Starline A64 alarm system. The question is related to autostart. He sets some strange conditions for the implementation of this function. That is, in order to remotely start the engine, you must first turn off the engine with an alarm (for example, you arrived at work, took the key out of the lock, the car continued to work, got out of it, set the alarm and it died), it seems to be good and autostart works when such actions. But if I need to get into the car during the day, I open it, take what I need and set the alarm again, then it is after that that it gives an error, like this neutral has not been maintained. I'm wondering if it's possible to somehow change these conditions so that it starts no matter how I get out of the car, what hand I scratch my butt with, etc.

Goods

smart immobilizer with Bluetooth Smart authorization

StarLine A93 2CAN+2LIN July 6, 2018
StarLine X96 Wins

Innovative security and telematics complex

How to install?

Installation Guide:

The microprocessor module is mounted inside the car. It is not allowed to be installed in the luggage compartment or under the hood. It is advisable to choose a hidden place for installation. For example, behind the control panel or in the free space behind the center console.
Depending on the chosen installation location, the plastic lining around the steering wheel or dashboard is dismantled. There is a temperature controller inside the microprocessor unit, so the device must be installed away from heat sources. If the unit may be exposed to moisture at the installation site, it must be installed with the connector facing down to prevent liquid from getting inside. Secure the device with screws or ties to prevent it from vibrating.
The antenna module is fixed on the inner surface of the windshield (it must first be washed and degreased). There should be metal parts of the body no closer than 5 cm from the transceiver, this will ensure the best range of the communicator. Inside the antenna module housing there is a tilt and shock controller. To prevent the controller from operating without reason, it should not be placed on the plastic lining in the passenger compartment.
An LED indicator is installed on the dashboard or center console. Its installation must be done so that when blinking the light bulb is visible from the street.
A siren is being installed in the engine compartment. It should not be installed near the cylinder block or sources of moisture. The horn of the device is located downwards, this will prevent the accumulation of moisture inside. Choose a place for installation so that there is no access to the siren and its electrical circuits from under the bottom of the car. If you purchased a siren with a built-in battery (autonomous), then during installation you must ensure unobstructed access to its lock.
The service button is mounted in the cabin. It is advisable to hide it; to do this, the key can be disguised as one of the bundles with standard wiring.
After installing all the components, the electrical lines are laid under the plastic upholstery. When laying, please note that electrical circuits should be placed as far as possible from possible sources of interference. These include high-voltage cables, ignition coils, electronic devices, etc. After installation, wires should not come into contact with moving structural elements.

Photo gallery

The Avtozvuka Base channel showed mistakes that car owners may make when installing anti-theft systems.

StarLine A61 autostart module

For the StarLine A61 anti-theft complex, the M31 module is the only opportunity to acquire the auto-start option for the power plant. But this is not the only advantage of this device. Along with the desired function of setting up remote start, the car owner also gets the opportunity to:

turn off the windshield wipers using remote commands;
turn on and off remotely the heated seats or windows in the cabin;
simulate the functioning of an intelligent ignition switch;
program all the necessary engine parameters;
simulate a second starter signal in the event of an unsuccessful engine start during the first start.

One of the main advantages of the module is its versatility. It can be easily installed on any car model, no matter what type it is.

User manual

Full use of all options is allowed only after binding the key fob.

Guide to linking the keychain:

Turn off the ignition with the key in the Off position. With the system turned off, click on the service button seven times, then set the key in the lock to the ACC position. The siren speaker will play seven beeps, this indicates successful entry into the binding mode.
Simultaneously click on the first and second pager keys. The siren speaker will play one sound pulse, and one melodic signal will be played by the remote control beepper.
The previous paragraph is repeated for programming each communicator. The time interval between binding each subsequent remote control should be no more than five seconds.
When the communicators are paired, you need to exit the programming mode. To do this, turn off the ignition. The car's lights should blink three times.

Read also: Connecting a rear view camera to a mirror recorder

How to disable?

If you were able to turn on the security, but cannot turn it off using the key fob, you can disable the security mode using the service button. For emergency shutdown, the consumer must know the password.

Procedure for turning off the alarm:

The door lock is opened with a key, the alarm siren will start playing alarm pulses. If the protective mode was activated without using the communicator, the vehicle's lights will blink four times.
Activate the ignition by inserting the key into the lock and turning it to the ACC position. Click on the service key several times. The number of presses must correspond to the first digit of the code. If it is 8, then the key is pressed eight times. When using a unique password, the alarm will disable the protective mode and the lights will blink twice. If the password is two-digit, then after entering the first digit the ignition is turned off.
The ignition is turned on again. The second digit of the password is entered into the service key. If the code was entered correctly, the protective function will be deactivated and the lights will blink twice. If a three-digit password is used, the ignition is turned off.
The key is again set to the ACC position, and the third digit of the password is entered.

Malfunctions that may require emergency shutdown of the alarm are described in the Falcrums channel video.

Is there auto start?

Initially, the Starline A64 alarm system does not have the option of automatic engine start. But it can be implemented by installing an additional special module from Starline M21 or M31.

Installation of these devices can lead to the following consequences:

Starting the power unit will only be possible using a smartphone application, as well as by calling and sending messages. Using a standard communicator will not allow you to configure this function.
There may be nuances regarding engine blocking. The consumer may have to block the ignition zone with the M21 or M31 module. The same goes for restoring blocked electrical circuits. It is almost impossible to perform the correct setup yourself; you will have to contact qualified installers.
Locks performed by the Starline A64 anti-theft complex will be canceled using the TX cable, which is blue. It is possible that the firmware of the M31 module and the A64 microprocessor unit will be different. As a result, you can try to solve the problem by updating the software. However, this procedure may be meaningless due to hardware incompatibility.

How to check if there is autorun?

The verification algorithm is not that complicated, follow all the steps sequentially:

Put the car on the handbrake, move the gear selector to neutral position.
Turn off the ignition; if the engine stalls, use the starter to start it again.
Next, on the Starline key fob, press the button with the key icon.
Now try to remove the key from the ignition, if you succeed, then your car has auto start. When you lock the doors, the engine will automatically stop after 30-60 seconds.

If, when you press the autostart button, you hear the engine cranking, but the engine does not start, you should check the settings. Read the security alarm operating manual carefully, then you can configure its operation correctly.

Malfunctions and ways to eliminate them

Problems that the consumer may encounter:

The alarm does not respond to commands sent. First of all, you need to diagnose the condition of the battery installed in the key fob. The battery is changed by removing the cover and removing the old power source. When replacing, observe polarity.
The signaling system reacts to sending commands every once in a while. The reason may be that the control button on your device is damaged or worn out. To solve the problem, you will have to disassemble the device case, clean it and replace the damaged button. To do this, you will need a soldering iron with a thin tip, as well as consumables (rosin and tin). If purchasing a new button is problematic, monitor the secondary market.
The range of the communicator has decreased. The problem may be that the battery is low. If the battery is working, you need to check the transceiver. Incorrect installation will result in reduced range. It may make sense to reinstall the device.
The alarm does not block all doors. The reason should be sought in the wires. Using a multimeter or voltmeter, the integrity of electrical circuits is diagnosed. If damaged wires are found, they must be replaced. If the cable insulation wears out, it is also recommended to change it. Before re-installation, we recommend additionally wrapping them with electrical tape, this will prevent rapid wear of the electrical circuits.
If the alarm does not work correctly, “glitches”, or turns on and off the protection mode for no reason, check the microprocessor unit. Malfunctions in the operation of the module may be due to the need to update the firmware or external influences. The latter include mechanical damage, regular vibrations, and moisture ingress. To solve problems, we recommend drying the module and checking its operation again. If the problems persist, you need to seek help from a specialist to reflash the device.

Features of car alarms

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

Read also: Lowered springs for Polo sedan

The car alarm is characterized by the presence of a shock-resistant control key fob, which allows you to control it at a certain distance. The device has a 128-channel noise-resistant transceiver, the operating range of which is 2000 meters. Thanks to the presence of a built-in integrated CAN interface in the car alarm, with the help of which the process of installing a car alarm is simplified and accelerated. The device can be installed in more than 300 vehicle models.

Typical malfunctions of car alarms

Starline A62

CAN bus module

Phone control

Auto engine start

Digital locking relay

GPS module

Automatic communication control

Malfunction

False positives

The sensor must be firmly attached to the body, placing it approximately in the center.

Starline A64

Possible reasons	Shock sensor is not configured properly The device is not securely fastened to the body
Methods for troubleshooting	The Starline A62 car alarm shock sensor is adjusted manually using the regulator on the body.

Malfunction	The central button on the key fob gets stuck
Possible reasons	Since the A64 has a large main button, with which all basic actions are performed, it bears a large load. Over time, the key begins to sink or respond poorly to pressing.
Methods for troubleshooting	To replace the button, you must contact an alarm repair center. Most services offer a replacement service. If the button is stuck, and there is no way to contact a specialist, you need to disassemble the key fob, clean it of dust and wash the contacts with alcohol.

Features of anti-theft functions

When using this device, you can connect a digital wireless locking relay. Thanks to the presence of a special connector, you can add a GSM/GPS module to the car alarm. If an alarm is connected to the device, the light will turn on when unauthorized access is attempted. Thanks to the presence of a special command in the a64 car alarm, you can easily control additional car door locks. With this device you can easily close the hood lock. If the need arises, you can additionally block the engine, thereby simulating its malfunction. When using this device, you can open the trunk if the standard alarm is disabled. Using a car alarm you are allowed to:

Control the preheater from a distance;
When the vehicle is moving, turn on the low beam headlights in automatic mode;
In automatic mode, install the seat for the car owner;
Return the steering column to its original position in automatic mode.

If the car owner turns on the security mode, the mirrors will fold automatically. The instructions will help you learn how a car alarm works. After the security mode is turned on, the light path lights up. Thanks to the security mode of this device, the hatch will turn on automatically. This car alarm model has excellent anti-theft functions, which allows the owner to be completely confident in its performance.

Alarm Starline autostart from key fob

Remote autostart starline

Before learning how to perform starline remote autostart, it is important to study some features. In order for you to be able to enable autostart from the key fob, it is important to meet the following conditions:

The first step is to put the car on the parking brake.
Turn the key in the ignition switch, and then remove the key (the engine must be turned off).
Next, move the gearbox lever to the neutral position.
Finally, it is worth closing all the doors tightly, as well as the trunk and hood.

Only if all the above conditions are met, then only in this case the security alarm will allow you to set it to autostart.

Switching to security mode with auto-start is also carried out in a special way:

Park and then put the car on the handbrake.
Move the gearbox selector to neutral.
Hold down button 1 on the key fob for 3 seconds, after which a ringing melody will sound.
Remove the key from the ignition.
Get out of the car (check that the doors are closed tightly). If you did everything correctly, the alarm will automatically turn off the engine, after which it will switch the alarm to security mode.

To perform a car factory remotely there are 2 ways:

Press button 1 for exactly 3 seconds, and then press button 3 until the signal appears.
Select the “start” icon, and then press button 2 once.

If the engine starts, you will see the symbol “exhaust gases” on the screen. The car will warm up for the time that you previously set in the settings. 1 minute before turning off the engine, the code “r01” will appear on the display. If the time is up, this code will change to “r00”.

Auto start on alarm clock

First of all, check the time of the on-board computer, it should be as accurate as possible. To enable auto start on an alarm clock, you must follow all the steps according to the instructions:

First, enable the option on the keychain with the bell icon.
Having set the desired time for the alarm, press keys 3 and 1 in turn, confirm your choice on the dial icon. If autostart is configured correctly, the car will blink its side lights.

When the function is turned on, the picture of the bell and dial will change on the display, and a long melody will also be heard.

Auto start by timer

Activation of this option is done as follows:

Move the cursor over the hourglass, then confirm your choice by successively pressing buttons 3 and 1.
Set the desired time, and then confirm the activation of the function in the same way.

If you decide to disable the enabled engine start by timer, then this is very simple - press button 2 twice quickly. The previous timer display will disappear from the display, and the key fob will also notify you with a signal that the timer has been turned off.

Autostart based on temperature indicators

This option is one of the most useful; sensors monitor the ambient temperature, and when the desired temperature is reached, the engine starts. You can activate the option using these instructions:

Move the cursor to the “thermometer” icon, briefly press button 1, then you will see a flash of the dimensions and a sound signal on the key fob. At the same moment, the current outside temperature should be displayed for 5 seconds.
Quickly press button 1 to set the required temperature parameters.
Long-pressing button 1 activates the automatic start mode based on temperature.

The option is deactivated using the same method as described above, only in our case the pointer now needs to be placed on the “thermometer” icon.

If you want to visually see how autostart is configured depending on the temperature on a Starline alarm, then watch this video

Setting up autorun using a phone application

Automatic engine start using a smartphone is a useful option, since the driver has the opportunity to start the engine from anywhere on Earth (if a GPS module is built-in). If your security alarm from Starline has a GPS module, then you can start it in the following ways:

By sending an SMS message to the SIM card installed in the key fob.
On call.
By sending a command using a special application, which must first be installed and then connected to the machine.

The app can be downloaded from the most popular app stores and is completely free for everyone. The developers have made the interface as simple and understandable as possible, so even a child can understand the controls.

Standard and programmable car alarm functions

Car alarms have many functions, the main ones of which include:

The vehicle coordinates are determined thanks to the presence of a GPS-GLONASS telematics module.
This device is protected from various code grabbers thanks to the presence of an interactive control code that has individual encryption keys.
Despite the presence of a large amount of urban radio interference, the car alarm works perfectly. This provides a unique narrowband transceiver.
The fastest possible response to the processes of jacking and evacuation of the vehicle is achieved thanks to the presence of a 3D shock and tilt sensor in the device.
Full operation of the car alarm is ensured in the temperature range from -50 to +85 degrees. This is ensured by the high quality of the components of this device.
The a64 car alarm is battery operated. Thanks to the record energy efficiency of this device, the battery charge can be maintained for 60 days.
During the production of car alarms, patented advanced technologies and software solutions are used, which significantly improves the quality of its work.

Thanks to the built-in CAN telematics on the starline a64 car alarm, quick, simple and convenient installation of security systems on modern vehicles is ensured, and you can also control it from your phone. Using this function, a person will know about the operating features of the car alarm, since he will receive notifications on his mobile phone if there are changes. The communication channel of the starline a64 car alarm, the instructions for which are included in the kit, is controlled automatically. Using this function, the location of the key fob within the range of the transceiver is checked. The Starline car alarm key fob is characterized by the presence of a shock-resistant structure and ergonomic design, and an internal protected antenna. Thanks to the presence of flexible service channels in car alarms, control parameters can be programmed. The instructions will tell you how to set up a car alarm so that the seats work automatically, the mirrors fold, and the hazard warning lights work correctly. Hidden, silent operation of this equipment is ensured by the presence of power switches. They also protect absolutely all car alarm outputs from the possibility of an accidental short circuit.

How to install autostart on Starline A61 alarm system

Before proceeding with installation, you must make sure that the selected location is not close to the radio or walkie-talkie. Otherwise, radio interference will interfere with the correct transmission of the signal from the key fob and you will have to reinstall it.

In general, the M31 installation instructions are quite simple and allow for independent installation of the device. To install the module, you must perform the following steps:

First of all, insert a SIM card inside the module, which is used to connect the system with the car owner’s mobile phone. The card is placed in a special hole hidden by a lid. This action must be performed with the power turned off. You can use SIM cards from any operator, although in some cases they are included with the device when you purchase it. But the consumer is not obliged to use the SIM cards supplied by the manufacturer.
At the next stage, the module itself is installed. A rather secretive place in the cabin is chosen for it, but one to which the driver has free access. Most often, this is the area behind the dashboard or control panel. M31 is placed so that the connector faces down - this will protect the device from moisture. Secure in place using plastic clamps or the included sticker. In some cases, it is possible to use self-tapping screws. The reliability of the fastening plays a big role, since vibrations of the car while driving can lead to incorrect operation of the module or even damage to it.
Finally, the module is connected. To do this, it is connected to the main control unit of the anti-theft complex, using the block provided by the manufacturer with three contacts on it. The required connector is colored blue. To connect, you need to use the cable that is included in the package.

Manufacturing Features

The production of the Starline A64 car alarm is carried out from the highest quality materials, which provides it with a high degree of strength and reliability. This equipment is characterized by fairly small dimensions, which allows it to be installed in any convenient location of the vehicle. The Starline A64 car alarm is produced, the instructions for which are attached in accordance with international quality standards, which guarantees its long service life. A car alarm is characterized by the presence of a plastic sealed housing, which limits the possibility of dust, dirt, and moisture getting into the mechanism, and also protects it from a variety of negative environmental influences. The development of the starline a64 slave car alarm was carried out on the basis of engineering and technical innovations. Thanks to the presence of a special mode, the car is disarmed using its original key fob. The instructions will tell you how to set up the operation of the key fob for this equipment. The starline a64 car alarm is a universal device that will provide reliable protection of the car from unauthorized access. Thanks to the presence of a large number of functions, additional convenience is provided during operation.