Procedure for replacing low beam headlight bulbs
Let's look at how to change a light bulb in a Volkswagen headlight. First of all, it is necessary to clarify what type of lamps are used for low beam and purchase a suitable option for use. In addition, in most cases it is necessary to install both bulbs at once, since for high-quality lighting you need a kit selected according to all operating parameters. It is never possible to combine old and new lamps; the difference is too noticeable.
What you will need
To remove and install the Volkswagen Polo low beam lamps you will need:
- Torx screwdriver T-30 (star);
- flat screwdriver;
- fabric gloves;
- clean napkin and alcohol;
- hook from a car tool kit.
Alcohol and a cloth will be needed to wipe the halogen lamp bulb before installation. You cannot touch it with bare hands, as greasy stains from strong heating darken and worsen the parameters of the light flux.
Important! Before starting work, it is necessary to ensure conditions for convenient and quick completion of the procedure. You need to open and secure the hood, disconnect the negative terminal from the battery. After this, you can begin to directly remove the burnt out lamp and install a new one.
Step-by-step instruction
The procedure for performing work on a Volkswagen Polo is as follows:
- Using a star screwdriver, unscrew 2 screws from the metal fastener so that you can remove the headlight;
- carefully disconnect the block with the lamp’s power wires by pressing the plastic latch;
- press on the bottom of the headlight and pull it out of the socket. There are 2 more latches, so you will have to apply some force;
- remove the sealing cone by turning it counterclockwise;
- remove the burnt out lamp and replace it with a new one;
- We assemble and install the headlamp in the reverse order.
Important! Experienced people say that replacing one lamp on a Volkswagen Polo takes no more than 10 minutes. For a beginner doing this for the first time, it may take a little longer. There is no need to rush; all actions must be performed thoughtfully and carefully.
Volkswagen Polo How to Change the Low Beam Bulb ~ AUTOINTERLINE.RU
Replacing a low beam lamp on a Polo Sedan: selecting light bulbs and replacing fuses
For the most part, problems with low beam on a Volkswagen Polo are associated with burnt-out lamps. Thanks to convenient access to the rear side of the headlight units, it is possible to replace lighting elements in a short time, without any difficulties. The only thing is that we first recommend studying in detail the main nuances of this operation and the procedure that will be discussed here.
Near
light
Volkswagen Polo
Replacing low beam bulbs
Choice
You, replacing a low beam lamp on a Volkswagen Polo Sedan for beginners begins with their choice. It should be said right away that the car uses double-filament halogen lamps of the H4 standard, i.e. They are also the main lighting lamps. They can be distinguished from single-strand ones, of course, by the presence of three contacts on the base.
Double strand H4 bulb
In the auto parts industry they offer a wide range of such lamps from various manufacturers. Moreover, the price of a product is often not a guarantee of quality. Therefore, when choosing, first of all you need to focus on the following characteristics of the lighting element:
Advice! Pseudo-xenon bulbs are available for sale.
These are the same “halogens”, however, they provide light blue light, close to daylight.
How to change the low beam light bulb on a Peugeot
Such lamps illuminate the space well in dry weather, but in rain, or snow, they are inferior to ordinary ones.
In the photo - a halogen light bulb
"pseudo-xenon"
This means that you can purchase lighting elements only in large specialized stores, despite the fact that you will find their prices higher than those from market sellers. However, there is less chance of purchasing a fake, which will quickly burn out, or the light will be of poor quality.
As for manufacturers, it is better to trust well-known brands such as
It must be said that domestic Mayak light bulbs are now popular among car enthusiasts. Their cost is cheaper than imported analogues, but they do not differ in quality.
Advice! Before purchasing a different lamp model, it is advisable to find out all the reviews about it on the Internet.
Replacing a Polo Sedan lamp
Today the right low beam bulb burned out .
OSRAM Night Breaker Plus. She served for about 8 months. Returned it.
Once you have decided on the type of lighting element, you can make a purchase. Moreover, it is better to purchase lamps in pairs. It is true that the light of different models is usually different, and such actions are clearly visible during their operation.
Replacing the low beam light bulb Volkswagen Polo sedan
Today, the durability of headlight bulbs, nettles, and KIA ones is approximately the same. If the low beam on a Volkswagen Polo does not light up in one headlight, then, most likely, in the near future it will go out in the next headlight.
Removing the pad and boot
Procedure
What is needed, replacing the low beam light bulb on a Volkswagen Polo sedan is carried out in the following sequence:
- First of all, you need to open the hood and disconnect the negative terminal from the battery.
- Then you need to disconnect the block from the contacts of the base. For this purpose, you need to pull it only towards you, slightly swaying it from side to side.
- Next you need to remove the rubber plug.
- Later, access will open to the spring lock, which must be unfastened by pulling it only towards you. (See also the article Fog lights on Mazda 6: features.)
- Now, of course, remove the old light bulb and install a new one in its place. It is better to wear gloves when replacing the lamp so as not to touch its glass on your own. Otherwise, grease stains will remain on the bulb, which will lead to overheating and rapid wear of the lighting element.
- Next, the work is performed in the reverse order - the base is fixed with a spring, the boot is installed in the area and then the block is put on the contacts.
Here, in fact, are the entire instructions. Even for beginners, this work takes 10-15 minutes.
Volkswagen Polo how to change low beam light bulb
Advice! If you touch the glass bulb of a light bulb with your bare hands, you can wipe it with alcohol.
According to this scheme, the low beam lamp of Volkswagen Polo Sedan is changed on both the left and right sides.
Replacing fuses
It happens that even after replacing the low beam lamp on a Volkswagen Polo does not light up. You, the reason for this is blown fuses. Change
they are even simpler than lamps.
Fuse layout
The mounting block is located on the instrument panel, at the bottom left side. To access it you need to open the cover.
Then we are interested in the following fuses:
- BS39 – responsible for the right headlight;
- BS59 – responsible for the left headlight unit.
Often, a fuse failure cannot be determined visually. Therefore, even if it does not have external signs of defects, it is necessary to check its performance with a device, or install a new fuse.
Look! Low beam malfunction can also be caused by oxidized, or burnt out, contacts in the block on another relay.
The problem is solved by cleaning the contacts.
Conclusion
Low beam lamp
The Polo Sedan is changed by performing a few simple steps. In this case, you need to follow the recommendations given above so that the process is safe and does not even affect the durability of the new lamp. On the contrary, replacing the lighting elements did not give the desired results; it is necessary to check the fuses.
How to change a low beam light bulb on a Solaris
Find out all the useful information on the above topic from the video here, of course.
Source: https://autointerline.ru/folksvagen-polo-kak-pomenjat-lampochku-blizhnego/
Replacing low beam lamps on Polo 2011 - 2015
Removing the low beam lamp in the pre-restyling model is carried out without dismantling the headlight. All you have to do is open the hood and access it from the back.
- It is necessary to dismantle the electrical block H4. The block “fits” very tightly, so in order to remove it, you need to forcefully pull it in the opposite direction.
- Then remove the rubber boot.
- The low beam lamp is held in place with a spring clip. The clamp itself is attached to the metal body of the reflector. You just need to apply a little pressure on the latch so that it clicks and releases it.
- To remove the lamp, the clamp is pulled down, and the light source itself is easily removed from its seat.
Remove and install lamps carefully, without touching the glass with your fingers.
Contact with fingers leads to the appearance of grease marks on the flask. After turning on the light, the glass will heat up and the marks will become clearly visible. Therefore, it is recommended to carry out all operations wearing work gloves. Or remove traces with a rag or cloth soaked in an alcohol solution.
After removal, assembly of the unit is carried out in the reverse order. The lamp in the second block is replaced in the same way. Car owners can easily carry out all the work with their own hands.
The final stage is verification. You need to make sure that the headlights are working properly.
Replacing headlight bulbs Polo sedan
The first thing you need to do is remove the electrical connector from the lamp.
One of the most loaded lamps in a car is low beam, which in urban environments is used much more often than high beam. The strictness of the requirements for the condition of head optics is due to the need to ensure safety for all road users. If the low beam lamp of a Volkswagen Polo fails, you have to change it immediately, otherwise it will become impossible to operate the car. The question is quite extensive and requires careful consideration.
Replacing the low beam lamp on a restyled version of VW Polo
To make it easier to replace the lamp, the headlight should be removed. To remove it we need a Torx T27 key
Unscrew the two screws securing the headlight using a Torx T27 key
In addition to the screws, the headlight is held on by 2 latches; carefully pull the headlight towards you and remove it from the latches. To remove the headlight, you need to disconnect the pads.
Having pulled out the headlight, remove the rubber boot
We take the lamp holder and turn it counterclockwise half a turn, pull it out of the headlight
We take out the old lamp, install a new one and reassemble in the reverse order.
LED lamps for low beam VW Polo
LED lamps are becoming more and more firmly integrated into everyday life every day. If previously they were installed in side lights and license plate lights, now LEDs are also installed in low beam headlights. When installing high-quality lamps, they provide bright light and good illumination of the road. According to motorists who have installed such lamps, LEDs shine better than halogen lamps.
What kind of lamps are on the Volkswagen Polo sedan?
1 Low and high beam lamp - H4 halogen lamp; power 60/55 watts. Cylindrical in shape, with three electrical contacts. Has two filaments.
2 Front fog lamp - halogen lamp HB4 with a power of 50 watts. L-shaped lamp with a plastic base.
3 Reversing lamp, fog lamp and brake signal - single-pin incandescent lamp PY21W, 21 watt.
4 Turn signal lamp - single-pin incandescent lamp PY21W, 21 watt orange.
5 The lamp for lighting the license plate, trunk, interior lamp and front marker is a small single-pin W5W lamp with a power of 5 watts.
