Lamps used on the Lada Kalina car. how to replace a low beam lamp on a fret viburnum what kind of lamps on a viburnum 1

What kind of lamps are there in Kalina?

Note. * The number of lamps depends on the vehicle configuration.

Heading optics contains 4 lamps

Let's look at how the directional optics, that is, the front headlight, is designed. The block contains four compartments, each of which contains one element:

• High beam lamp (H1);
• Low beam lamp (H7);
• Combined lamp for running lights and “dimensions” (W21/5W);
• Turn signal lamp (P21W yellow - PY21W).

The standard size of the element is indicated in parentheses.

If we talk about low and high beams, standard power lamps (55 watts) are installed from the factory. It is not recommended to greatly exceed this value. Lighting fixtures of sizes H1-H7 look like this:

H1 – high beam, H7 – low beam

When making a purchase, the main thing is not to confuse an H7 lamp with a halogen lamp of a similar size (H4). Also, some companies produce 24-volt lighting devices.

When replacing halogen light sources, adhere to the following rules: do not touch the glass with hands without gloves; it is recommended to degrease the lampshade before installation. “Secunda” is suitable as a cleaner.

The following text shows the side and running lights:

There will be two filaments in the headlight bulb and DRL

Its standard size is W21/5W. Well, the turn signal bulbs in the directional optics use standard ones. They are equipped with a metal base, their standard size is P21W (PY21W).

The yellow lampshade looks like orange

Low beam lamp Kalina

Design of the H7 low beam lamp of the VAZ 1117, 1118, 1119 Kalina passenger car:

Designation of low beam headlight lamp according to EEC - H7

Technical characteristics of the Lama H7 low beam headlights Kalina:

• Power - 55 W;
• Light - xenon;
• The base is metal;
• The base is round;
• The color of the flask is transparent;

Dimensions of low beam lamp Lada Kalina

• The diameter of the flask is 11 mm;
• The size from the tip of the flask to the seat is 44 mm;
• Lamp height - 60 mm;
• Base height - 16 mm;

Installation location of the H7 low beam headlight lamp:

The car has two such H7 bulbs.

How to choose good lamps

It is not enough to replace a faulty element in a car; you also need to select the right spare part. Light bulbs are no exception. The auto parts market offers a large selection of lighting devices from a variety of manufacturers with appropriate quality.

Conventionally, lamps can be divided into three categories:

• Good lamps should last a long time, but don't have to be expensive. Quite good manufacturers, such as Philips, Osram, etc., sell affordable lighting devices with standard characteristics. The price of one lamp, for example, with an H1 base is, on average, 102 rubles. In this case, the characteristics will be averaged, as on standard lamps with, “Dialuch” and other lamps, on the packaging of which you can find Chinese characters, are cheap low-quality light sources. The illumination is worse, and the service life can sometimes exceed the operating time of even the most expensive lamps.
• A separate category of light sources are expensive light bulbs or, as they are commonly called, high-brightness lamps. Trivial examples are: Osram Nigth Breaker +110 or Philips Racing Vision +150. In fact, the brightness of such lamps is actually higher, since they operate in overheating mode. But durability is less. You can also include LED lamps and xenon, as this is a kind of optics tuning.

When it comes to choosing a lamp, we always think of light sources for low beam headlights or PTF. For other luminaires, lamps are selected with much lesser requirements.

Headlight bulbs for Lada Kalina

List of headlight bulbs for Lada Kalina:

• Low beam lamp;
• High beam lamp;
• Electric lamp dimensions;
• Front turn lamp.

Description of the design of the headlight block on the Lada Kalina:

1. High beam and side beam section;
2. Low beam section;
3. Front turn signal section

High beam headlight bulb

Design of the AKG12-55-2 N1 high beam lamp for VAZ 1117, 1118, 1119 frets Kalina:

Designation of the high beam headlight bulb on the Lada Kalina:

• According to the EEC - H1;
• According to GOST - AKG12-55-2.

Technical characteristics of the llama headlight AKG12-55-2 N1 high beam frets Kalina:

• Power - 55 W;
• Light - xenon;
• The base is metal;
• The base is flat;
• The color of the flask is transparent;

Dimensions of the high beam headlight bulb for Kalina cars

• The diameter of the flask is 8.5 mm;
• The size from the tip of the flask to the seat is 44 mm;
• Lamp height - 62.5 mm;
• Base height - 18.5 mm;
• Base diameter - 24.5 mm;

Installation location of the headlight lamp AKG12-55-2 N1 high beam frets Kalina:

The car has two such H1 bulbs.

Headlight lamp A12-21-4 PY21W turn signal

Design of the headlight lamp A12-21-4 PY21W direction indicator VAZ 1117, 1118, 1119 frets Kalina:

Designation of the turn signal headlight lamp Lada Kalina:

• According to EEC - PY21W;
• According to GOST - A12-21-4.

Technical characteristics of the headlight llama A12-21-4 PY21W direction indicator Lada Kalina:

• Power - 21 W;
• Light - normal;
• The base is metal;
• The base is round;
• The color of the flask is red;

Dimensions of turn signal headlight bulbs for Kalina cars

• The diameter of the flask is 26.5 mm;
• The size from the tip of the flask to the seat is 45 mm;
• Lamp height - 52.5 mm;

Installation location of the headlight lamp A12-21-4 PY21W turn signal indicator Lada Kalina:

There are two such bulbs installed on the car.

Side light bulb A12-5-2 W5W

Design of the headlight lamp A12-5-2 W5W side light VAZ 1117, 1118, 1119 frets Kalina:

Designation of the headlight lamp of the dimensions of the Lada Kalina:

• According to EEC - W5W;
• According to GOST - A12-5-2.

Technical characteristics of the llama headlight A12-5-2 W5W dimensions of the Kalina fret:

• Power - 5 W;
• Light - normal;
• Base - glass;
• The base is flat;
• The color of the flask is transparent;

Dimensions of headlight bulbs for Kalina cars

• The diameter of the flask is 10.3 mm;
• The size from the tip of the flask to the seat is 20.7 mm;
• Lamp height - 26.8 mm;

Installation location of headlight bulb A12-5-2 W5W dimensions fret Kalina:

There are two such bulbs installed on the car.

Removing and installing Kalina size lamps

To replace the side light bulbs in the headlight, you will need to remove the protective rubber cover by pulling one of its three blades.

1. Remove the bulb socket.
2. Remove the lamp from the socket.

Installing a new side light bulb (W5W) is done in the reverse order.

Side direction indicator lamp

Design of the lamp A12-5-2 W5W for side direction indicators VAZ 1117, 1118, 1119 frets Kalina:

Designation of the side direction indicator lamps Lada Kalina:

• According to EEC - W5W;
• According to GOST - A12-5-2.

Technical characteristics of Lama A12-5-2 W5W side direction indicators frets Kalina:

• Power - 5 W;
• Light - normal;
• Base - glass;
• The base is flat;
• The color of the flask is transparent;

Dimensions of the side direction indicator lamps for Kalina cars

• The diameter of the flask is 10.3 mm;
• The size from the tip of the flask to the seat is 20.7 mm;
• Lamp height - 26.8 mm;

Installation location of the A12-5-2 W5W side direction indicator lamp for Kalina frets:

There are two such bulbs installed on the car.

Electric tail light bulbs viburnum

List of lamps located in the rear lamp of the Lada Kalina car:

• Brake light;
• Reverse light;
• Turn signal lamp;
• Side and fog light lamp;

1. Additional brake light;
2. Brake signal section;
3. Reversing light section;
4. Rear turn signal compartment;
5. Side and fog light section.

Turn signal lamp

Design of the A12-21-4 PY21W turn signal lamp in the rear light of VAZ 1117, 1118, 1119 frets Kalina:

Designation of the direction indicator lamp in the rear light of the Lada Kalina:

• According to EEC - PY21W;
• According to GOST - A12-21-4.

Technical characteristics of the Lama A12-21-4 PY21W direction indicators in the rear light of the Lada Kalina:

• Power - 21 W;
• Light - normal;
• The base is metal;
• The base is round;
• The color of the flask is red;

Dimensions of the turn signal lamp in the rear light of a Kalina car

• The diameter of the flask is 26.5 mm;
• The size from the tip of the flask to the seat is 45 mm;
• Lamp height - 52.5 mm;
• The size from the filament to the base stop is 31.8 mm.

Installation location of the A12-21-4 PY21W turn signal lamp in the rear light of the Lada Kalina:

There are 2 of these lamps installed on the car.

Rear fog and side light bulb

Design of the lamp A12-21+4 P21/4W for fog and side lights in the rear light of VAZ 1117, 1118, 1119 frets Kalina:

Designation of the fog and side light lamps in the rear light of the Lada Kalina:

• According to EEC - P21/4W;
• According to GOST - A12-21+4.

Technical characteristics of the Lama A12-21+4 P21/4W fog and side light in the rear light of the Lada Kalina:

• Power - 21/4 W;
• Light - normal;
• The base is metal;
• The base is round;
• The color of the flask is transparent;

Dimensions of the fog and side light lamps in the rear light of a Kalina car

• The diameter of the flask is 26.5 mm;
• The size from the tip of the flask to the seat is 45 mm;
• Lamp height - 52.5 mm;
• The size from the filament to the base stop is 31.8 mm.

Installation location of the A12-21+4 P21/4W lamp for fog and side lights in the rear light of the Lada Kalina:

There are 2 of these lamps installed on the car.

Electric brake signal lamp for Lada Kalina

Design of the brake light lamp A12-21-3 P21W in the rear light of VAZ 1117, 1118, 1119 frets Kalina:

Designation of the brake light lamp in the rear light of the Lada Kalina:

• According to EEC - P21W;
• According to GOST - A12-21-3.

Technical characteristics of the Lama A12-21-3 P21W brake light in the rear light of the Lada Kalina:

• Power - 21 W;
• Light - normal;
• The base is metal;
• The base is round;
• The color of the flask is transparent;

Dimensions of the brake light lamp in the rear light of a Kalina car

• The diameter of the flask is 26.5 mm;
• The size from the tip of the flask to the seat is 45 mm;
• Lamp height - 52.5 mm;
• Base diameter - 15 mm

Installation location of the brake light lamp A12-21-3 P21W in the rear light of the Lada Kalina:

There are 2 of these lamps installed on the car.

Reversing light lamp

Design of the A12-21-3 P21W reverse lamp in the rear light of VAZ 1117, 1118, 1119 frets Kalina:

Designation of the reversing lamp in the rear light of the Lada Kalina:

• According to EEC - P21W;
• According to GOST - A12-21-3.

Technical characteristics of the Llama A12-21-3 P21W reverse gear in the rear light of the Lada Kalina:

• Power - 21 W;
• Light - normal;
• The base is metal;
• The base is round;
• The color of the flask is transparent;

Dimensions of the reversing lamp in the rear light of a Kalina car

• The diameter of the flask is 26.5 mm;
• The size from the tip of the flask to the seat is 45 mm;
• Lamp height - 52.5 mm;
• Base diameter - 15 mm

Installation location of the A12-21-3 P21W reverse lamp in the rear light of the Lada Kalina:

There are 2 of these lamps installed on the car.

How to replace the lamps yourself

Replacing a low beam lamp on a Kalina
It is not difficult to change a light bulb on a Kalina yourself. The time spent on the work depends on the skill of the driver and the size of the hands. Some owners change light fixtures in 15-20 minutes without removing the headlight, while others suffer for more than an hour and ultimately dismantle the optics.

When replacing, cloth gloves are used. This helps protect the skin on your hands and also prevents contact with the bulb. When touched, fingerprints remain, which heat up when the light is turned on and after a while burn through the thin glass.

During work, the battery terminal is unscrewed to avoid a short circuit, which will lead to burnout of the fuse link in the fuse box.

Far module

Replacing the high beam lamp is easier than in the low beam module, since the cover is located closer to the radiator grille.

To perform the operation you will need:

1. Turn off the Kalina engine.
2. Open the hood lid.
3. Remove the protective boot on the back of the flashlight.
4. Carefully disconnect the plastic chip.
5. Open the latch.
6. Pull out the lamp.

Assembly is carried out in reverse order. When installing the terminal, you need to check the contacts and, if necessary, clean them using a flat-head screwdriver, sandpaper or a special chemical spray.

Low beam

Replacing a low beam lamp on a Lada Kalina depends on the experience of the owner and is divided into two types:

1. Without removing the headlight.
2. With module dismantling.

Most Kalina owners cannot replace the lamp in the left headlight due to limited space. In this case, you will have to ask a more dexterous friend or dismantle the lighting device yourself for convenience.

To change lamps on installed optics:

1. Unscrew the filter housing near the left headlight and move it towards the engine.
2. Disconnect the washer motor terminal, remove the screws and move the reservoir to the side.
3. Open the light module seals.
4. Remove the block with wires.
5. Remove the spring clip.
6. Remove the part.

Assembling the headlight with a new spare part is carried out in the reverse order.

To dismantle the headlights, you need to unscrew the grille, fasten the modules and disconnect the contact chip. Place the removed optics on a convenient surface and replace the light elements.

Dimensions and DRLs

In the first generation Kalina, the dimensions are installed under the cover of the near reflector.

Replacement is no different from work in the near headlight compartment, however, to disconnect the lamp, it is turned counterclockwise. Drivers often install a diode instead of the original light source, which has a bright glow and can work for more hours.

Replacing DRL lamps on second generation Kalina:

1. Open the hood.
2. Find the plastic retainer at the bottom of the lamp near the radiator grille.
3. Turn left 90°.
4. Pull towards yourself.

Daytime running lamps do not contain halogen in the bulb, so they can be handled by hand when installing. Parts without gas include reverse elements, which are changed by bending the trim in the luggage compartment. To replace the Kalina station wagon's brake light bulb, you will have to unscrew the plastic plug on the fifth door, disconnect the chip and pull out the old spare part.

Turn signal

If the marker light on Kalina is freely accessible, then it is more difficult to get to the turn signal module.

To install a new lamp, you need:

1. Unscrew the screws holding the air intake barrel and washer fluid reservoir.
2. Move the parts towards the engine.
3. Feel for the plastic cartridge and turn it to the left.
4. The lamp is removed from its seat by slightly pressing and turning it 90° to the left.

To install a new part, you need:

1. Install it into the cartridge.
2. Press and turn to the right until it stops.

The finished element is mounted in a standard hole. You can check the operation of the light by turning on the corresponding key on the Kalina instrument panel.

Fog lights

When replacing the fog lights, partial dismantling of the locker will be required. To do this you need:

1. Turn the wheel towards the engine compartment.
2. Unscrew the screws and unclip the clips where they are attached to the bumper.
3. Bend the fender liner.
4. Turn the light bulb to the left until it stops.
5. Pull towards yourself.
6. Disconnect the plug.

To install a new light source in the PTF, you must first snap the connector, insert the part into the lamp and turn it to the right.

After carrying out the work, you need to check the correct functioning of the light and adjust the angle of the reflector. A properly functioning car light ensures good visibility in all conditions and safety on the road.

Lada Kalina license plate lamp

VAZ 1117, 1118, 1119 Lada Kalina lamp AC12-5-2 W5W license plate illumination

Designation of the Kalina fret number lamp:

• According to EEC - W5W;
• According to GOST - AS12-5-2.

Technical characteristics of the lama AC12-5-2 W5W for illuminating the license plate of the Kalina car:

• Power - 5 W;
• Light - normal;
• Base - glass;
• The base is flat;
• The color of the flask is transparent;

Dimensions of the fret lamp Viburnum number plate illumination

• The diameter of the flask is 10.3 mm;
• The size from the tip of the flask to the seat is 20.7 mm;
• Lamp height - 26.8 mm;
• Base width - 9.5 mm
• Base thickness - 2.1 mm
• The size from the base stop to the filament is 12.7 mm.

Installation location of the AC12-5-2 W5W license plate illumination lamp on the Kalina fret:

There are 2 of these lamps installed on the car.

What causes lamps to burn out in Lada Kalina

There are three reasons why lamps in a car can burn out. And here is each of them:

1. Life time. It is worth noting that any lamp is designed for certain operating hours. Once the operating time exceeds its limits, the light source begins to dim, and then the filament melts and the light source stops working. The operating time of the lamp may be affected by the voltage of the on-board network.
2. All automotive light sources are designed for a voltage of 12 Volts, but not more than 14.7V. If this parameter is exceeded, the incandescent device begins to operate in overheating mode, which leads to its failure ahead of schedule. Overvoltage can occur due to a breakdown of the voltage regulator relay.
3. Quality. A lot depends on the quality of the light source - from illumination to service life. To prevent the lamp from burning out prematurely, try to choose light sources recommended by the manufacturer.

Interior light bulb

VAZ 1117, 1118, 1119 Lada Kalina lamp AC 12-10-1 interior light

Designation of the interior light bulb of the Lada Kalina:

• According to the EEC - -;
• According to GOST - AS 12-10-1.

Technical characteristics of Llama AC 12-10-1 car interior light Kalina:

• Power - 10 W;
• Light - normal;
• Base - metal 2 pcs;
• The base is round;
• The color of the flask is transparent;

Dimensions of the Lada Kalina lamp for interior lighting

• The diameter of the flask is 10.5 mm;
• Lamp height - 40 mm;
• The diameter of the base stop is 3.5 mm

Installation location of the AC 12-10-1 interior light lamp on the Kalina fret:

There is 1 such lamp installed on the car.

Individual lighting lamps

Design of lamp A12-4-1 T4W for individual lighting lamps VAZ 1117, 1118, 1119 Lada Kalina

Designation of the lamp for individual lighting of the Lada Kalina:

• According to EEC - T4W;
• According to GOST - A12-4-1.

Technical characteristics of the Lama A12-4-1 T4W individual light for the car Kalina:

• Power - 4 W;
• Light - normal;
• The base is metal;
• The base is round;
• The color of the flask is transparent;

Dimensions of Lada Viburnum lamp individual light

• The diameter of the flask is 9.2 mm;
• Lamp height - 26 mm;
• Base diameter - 9.1 mm
• The size from the base stop to the filament is 15 mm
• The size from the base stop to the lamp contact is 5.9 mm

Installation location of the A12-4-1 T4W lamp for individual light on the Kalina fret:

There are 2 of these lamps installed on the car.

Replacement of glass in the headlight unit of a Lada Kalina car (for Bosh headlights)

1. Remove the headlight unit from the car, see the operations described above 2. Remove the six metal rivets that hold the glass. You can remove the rivets using a flat blade screwdriver.

3. Remove the glass. 3. Install new glass on the headlight unit. (The seal between the glass and the headlight housing is sealed with a rubber seal. If the rubber has lost its plastic properties, use a sealant. Apply a thin layer to the place where the glass contacts the seal. Replace the glass, remove excess sealant. 4 Install the metal clips in their places. Reinstall the headlight.

Trunk light bulb

Design of the AC 12-5-1 C5W lamp for the trunk lighting of the VAZ 1117, 1118, 1119 Lada Kalina

Designation of the trunk light lamp of the Lada Kalina:

• According to EEC - C5W;
• According to GOST - AS 12-5-1.

Technical characteristics of Llama AC 12-5-1 C5W car trunk light Kalina:

• Power - 5 W;
• Light - normal;
• Base - metal 2 pcs;
• The base is round;
• The color of the flask is transparent;

Dimensions of the fret lamp Kalina trunk light

• The diameter of the flask is 10.5 mm;
• Lamp height - 35 mm;
• The diameter of the base stop is 3.5 mm

Installation location of the AC 12-5-1 C5W lamp for the trunk light on the Kalina fret:

There are 2 of these lamps installed on the car.

Replacement process

The process of replacing lights on the Lada Kalina 2 differs depending on its type. There are “Kalina 2” hatchback and station wagon. For a hatchback, the replacement sequence is as follows:

• open the 5th door of the car;
• Remove the 2 bolts securing the rear lighting component to the luggage compartment side. Use the key on 8;
• pull the light from the back of the car towards you, using little force;
• remove the fastener studs from the headlight fixing fasteners at the rear;
• move the lighting component away from the car body;
• if you need to replace the lamp, remove the socket with the broken product;
• After installing a new lamp in the lighting system, perform the entire process in reverse order.

Removing the rear light on a Lada Kalina hatchback The principle of removing a headlight on a Kalina (station wagon) and replacing the block lighting differs depending on the shape and structure of the car itself. For the process of replacing the rear light unit you will need:

• open the 5th car door;
• open the hatch located in the trunk trim;
• disconnect the block with the light cables at the rear of the car from the harnesses and wires;
• Unscrew the 3 nuts securing the product to the car body;
• disconnect the device lock;
• remove the lamp retainer from the car body.

If you are interested in replacing the lamp, then after the above steps you need to remove the broken socket by turning it counterclockwise. This way you can remove it from the headlight housing. The new lamp is inserted into the socket by pressing and turning it clockwise. If you need to completely replace the lighting, simply insert the new product into place and perform the reverse steps of disassembly.

Glove box light bulb

Design of lamp AC 12-5-1 C5W for lighting the glove compartment of VAZ 1117, 1118, 1119 Lada Kalina

Designation of the glove compartment lamp lamp of the Kalina fret:

• According to EEC - C5W;
• According to GOST - AS 12-5-1.

Technical characteristics of Llama AC 12-5-1 C5W glove compartment lamp for Kalina cars:

• Power - 5 W;
• Light - normal;
• Base - metal 2 pcs;
• The base is round;
• The color of the flask is transparent;

Dimensions of the fret lamp Viburnum glove compartment lamp

• The diameter of the flask is 10.5 mm;
• Lamp height - 35 mm;
• The diameter of the base stop is 3.5 mm

Installation location of the AC 12-5-1 C5W lamp for the glove compartment lamp on the Kalina fret:

There are 2 of these lamps installed on the car.

Other lamps in the station wagon and hatchback

To illuminate additional equipment in Kalina-2, lamps of standard size C5W are used. They are:

• In the license plate light socket ;
• In the trunk light;
• In the glove compartment lighting module.

The interior is illuminated by a C10W lamp, and additional side lamps are equipped with T4W lamps.

Light bulbs and body turn signals

The side turn signals are equipped with incandescent lamps without a socket (W5W). And H11 lamps can be installed in the front fog lights. Successful replacement.

Instrument panel lamp Lada Kalina

Design of the light bulb A12-1.2 W1.2W for backlighting the instrument panel VAZ 1117, 1118, 1119 frets Kalina

Designation of the instrument panel illumination lamp for the Lada Kalina:

• According to EEC - W1.2W;
• According to GOST - A12-1.2.

Technical characteristics of Lama A12-1.2 W1.2W for lighting the instrument panel of the car Kalina:

• Power - 1.2 W;
• Light - normal;
• Base - glass;
• The base is flat;
• The color of the flask is transparent;

Dimensions of the fret Kalina lamp for instrument panel lighting:

• The diameter of the flask is 5 mm;
• Lamp height - 20 mm;
• The size from the beginning of the base to its stop is 5.5 mm;
• The size from the base stop to the top of the lamp is 14.5 mm;

Installation location of the A12-1.2 W1.2W instrument panel lamp on the Kalina fret:

There are 4 of these lamps installed on the car.

Removing the instrument panel

Dismantling the Lada Kalina instrument panel is carried out as follows:

• lower the steering wheel to the lower position so as not to interfere. The regulator is located under the steering column;
• Unscrew the two screws holding the decorative trim. They are located in the upper part, you can get to them from below;
• pull out the cover by moving it towards you;
• Using a magnetized screwdriver, unscrew the two fasteners holding the instrument panel;
• tilt the panel and disconnect the block with wires. She is there alone, no other elements hold the dashboard.

It is necessary to act carefully and ensure that fasteners do not fall inside or onto the floor.

Display illumination lamp on the dashboard

Design of the light bulb A12-1.2 W1.2W for display backlighting on the instrument panel of VAZ 1117, 1118, 1119 frets Kalina

Designation of the display backlight lamp on the dashboard of the Lada Kalina:

• According to EEC - W1.2W;
• According to GOST - A12-1.2.

Technical characteristics of Lama A12-1.2 W1.2W lighting for the instrument panel display of the car Kalina:

• Power - 1.2 W;
• Light - normal;
• Base - glass;
• The base is flat;
• The color of the flask is transparent;

Dimensions of the fret Kalina lamp for the instrument panel display backlight:

• The diameter of the flask is 5 mm;
• Lamp height - 20 mm;
• The size from the beginning of the base to its stop is 5.5 mm;
• The size from the base stop to the top of the lamp is 14.5 mm;

Installation location of the lamp A12-1.2 W1.2W for illuminating the instrument panel display on the Lada Kalina:

There is 1 such lamp installed on the car.

Cigarette lighter socket light bulb

Design of lamp A12-1.2 W1.2W for lighting the cigarette lighter socket of VAZ 1117, 1118, 1119 frets Kalina

Designation of the light bulb for the location of the cigarette lighter on the panel of the Kalina fret:

• According to EEC - W1.2W;
• According to GOST - A12-1.2.

Technical characteristics of Llama A12-1.2 W1.2W illumination of the cigarette lighter socket of the car Kalina:

• Power - 1.2 W;
• Light - normal;
• Base - glass;
• The base is flat;
• The color of the flask is transparent;

Dimensions of the fret lamp Viburnum lighting cigarette lighter:

• The diameter of the flask is 5 mm;
• Lamp height - 20 mm;
• The size from the beginning of the base to its stop is 5.5 mm;
• The size from the base stop to the top of the lamp is 14.5 mm;

Installation location of the A12-1.2 W1.2W light bulb for lighting the cigarette lighter socket on the Kalina fret:

There is 1 such lamp installed on the car.

We remove the headlight, having previously dismantled the bumper on the Lada Kalina

In any case, you will need tools such as 8 and 10 mm wrenches, screwdrivers: flat and Phillips. Of course, you need to take care of spare parts in advance when it comes to lighting system components. I will especially say about the keys.

Drivers who do some work on their own know that there are open-end, socket and ring wrenches. If space allows, it is best to hold the nut with a socket or cap. Then all its sides are grasped. This ensures that the edges, if difficult to rotate, will not be damaged.

It is advisable to have heads as well. It is best if you prepare a ratchet. The fact is that in some places it is quite difficult to operate a simple key, since it turns at a small angle.

The first thing you need to do when dismantling the headlight and removing the bumper is to use a Phillips screwdriver to unscrew the four screws that secure the fender liners. After this, you need to find a couple more screws. They are below, one on the right and one on the left. To avoid mistakes and waste time, it is better to use an inspection hole.

If it is not there, then you can perform the operation lying on a pre-prepared mobile plane or on the floor, covering it with improvised material. When these two lower screws are also unscrewed, unscrew the three bolts also located at the bottom.

Now you can easily remove the radiator grille and unscrew the bolts that secure the bumper to the body. The next operation is to remove the decorative grille. It is made of plastic and is located under the license plate. There are two bolts there. They are easy to find. After they are unscrewed, you just need to pull the grill towards you.

The last step is to unscrew and remove the two screws under the license plate. Then we grab the edges of the bumper and, pointing it towards ourselves, tear it off the latches. The Kalina bumper is light. You can remove it from the latches and hold it suspended without an assistant.

And now the bumper is removed.

All that remains is to dismantle the headlight. To do this, remove the bumper power beam. Then remove the bolts securing the headlight. To find them, you need to tilt the beam a little to the side. These bolts are best removed using an 8mm socket equipped with a ratchet.

There are two more bolts at the top. We unscrew one with an 8 key, the second with a Phillips screwdriver. After this, disconnect the power plugs. It must be remembered that the fixation of these connectors is ensured by latches. Where they are located can be determined even by touch. The plug can only be disconnected by bending the latch. Now we just grab the headlight housing (take it with both hands) and remove it.