Alarm Tomahawk 9030: key fob operating instructions

The Tomahawk TW 9030 alarm kit includes two remote controls.

1. The main module is equipped with 5 keys and a liquid crystal display.
2. The spare key fob Tomahawk 9030 is equipped with 4 controls and an indicator diode.

Both transmitters are fully functional and allow you to use all security system options.

Don't forget that there is also a Tomahawk TZ 9030 alarm system.

What the Tomahawk TW 9030 keychain looks like: photo

The supplied pagers differ slightly. This is due to the reduction in cost of all signaling.

1. The main remote control is a rectangular block in a plastic case with a protruding antenna compartment. On the top wall there are three function keys responsible for the main options. On the front there is a screen and two more buttons for additional control.
2. The replacement element looks simpler. There is an oval plastic case with an eyelet for a key ring. There are 4 function keys at the front. The “F” element is missing, which does not allow entering the programming menu from an additional transmitter.

Functions

The basic key fob options are presented sparingly. However, the first element contains a set of required indications:

• display of the current alarm position;
• screen backlight;
• vibration alert;
• integrated clock, timer and alarm;
• key lock;
• battery saving.

Most of the functions are not available on the auxiliary device. However, this does not prevent you from fully using the system.

Keychain Tomahawk 9030: instructions for use

The factory booklet is supplied complete with the security system. But when buying a car with an already installed alarm system, 90% of the instructions do not reach the end consumer.

The user manual contains comprehensive information:

• sequence of installation of head units;
• how to use remote controls;
• capabilities and their activation;
• what to do in case of breakdown.

You can view the instructions by following the link.

We also have Tomahawk 9030 autostart instructions.

Setting instructions

1. To program the key fob, turn off the ignition.
2. Press the Override key seven times.
3. Turn on the ignition and wait until the siren sounds seven times. This is confirmation of entering programming mode.
4. Release Override.
5. Simultaneously press and hold the “Open Doors” and “Close Doors” buttons until the siren sounds. This confirms the successful recording of the new Tomahawk TZ 9030 alarm pager. Memorization of other key fobs is confirmed by a certain number of siren sounds.
6. Turn off the ignition. After six seconds have elapsed, the system will automatically exit setup mode.

You can manually register up to four remote controls in the alarm memory. This process is carried out only when the security mode is turned off. New key fobs are registered in memory after the old data is deleted.

We also have operating instructions for the Tomahawk 9030 key fob.

Icons on the Tomahawk 9030 key fob: symbols on the display

The head pager display panel provides the user with information about the system status in the form of icons. This is done due to the size of the display - full inscriptions will not fit here.

The operating instructions contain the necessary tables, where the inscriptions on the remote control screen and the indication of the spare key fob diode are fully deciphered.

PASS lights up on the remote control

The Pass icon indicates that the shock sensor warning zone is disabled. The function is activated when the car is locked with a passenger inside or near a road with heavy traffic.

You can disable the warning by double-clicking the “Zz” button. Doing this again will completely turn off the shock sensor. To restart the option, the steps are performed in the same way.

2 1 daily Tomahawk 9030: how to disable

When the hourly engine start mode is activated, the corresponding message appears on the display. Depending on the pre-programming, the engine will start every 1, 2, 4 or 24 hours.

The 2-1 daily mode is activated by simple manipulation:

• hold down the "key" key;
• the system will emit the corresponding chirp;
• quickly click on Zz;
• If everything is done correctly, the diode on the antenna will blink twice.

You can disable the extension in a similar sequence.

Find out everything about emergency disarming of the Tomahawk 9030.

Hijack icon is on

Some users do not know what the “anti-hijack” icon that appears on the head key display means. The Anti Hijack function in the Tomahawk TV 9030 alarm system is used to return a car in the event of a violent theft.

There are two ways to activate the anti-grabber.

1. While in the car, press OVERRIDE once and leave the car. To turn off the specified element is pressed three times.
2. On the remote control, press “Zz” and the key at the same time. The dimensions should blink. Switching off is done by pressing the button with a key pattern once.

The designation can also be turned off by entering a personal code on the alarm panel.

2-3 Auto Immo

The Tomahawk TW 9030 model has a built-in immobilizer. The module blocks the engine when attempting to steal a car. Indication 2-3 auto immo indicates that the mode is enabled.

Activation is performed by a sequential key combination, and reset can be done by holding down the button with the key pattern. The LED on the head antenna should go out.

1 2 temp start Tomahawk 9030: how to disable

The user manual contains information about automatic warming up of the power plant, which is necessary on first responder vehicles or in winter. If the response temperature is set correctly, the motor does not freeze.

If the icon on the screen is redundant (the option is not needed), you can remove it. You can turn off the 1-2 tempo start function from any remote control:

• hold Zz until the key fob beeps or a green beacon appears;
• quickly press the key.

5 KEY LOCK icon

The inscription 5 key lock appears when the remote control is locked from accidental key presses. This is required when carrying the device in a pocket, where there is a risk of unintentionally disarming the car.

Disabling the protection is performed by a simple manipulation - simultaneously pressing the open lock/key + “F”. If everything is done correctly, the key fob will squeak.

How to remove 1-1 ZZZ

Sleep mode or VALET is activated when the car is left at a service station where there is no risk of theft. This way, access to the vehicle components is gained and technicians can work in peace. At the same time, the inscription “1 1 zzz” lights up on the display.

Working with the option is performed with one key:

• when the signaling is turned off, press Zz until a squeak is heard from the key fob;
• click on the specified button again;
• If everything is done correctly, the car will blink its dimensions 4 times.

The option is disabled in a similar sequence. Or by holding OVERRIDE for 3 seconds.

Indication 2-4 Auto Arm

The automatic arming mode is accompanied by the 2 4 auto arm icon and is required to activate the Tomahawk TW 9030 without driver intervention. This is necessary if the owner forgot to turn everything on himself and left the car open.

You can turn the option on/off using a simple procedure:

• press the key in until a sound or green light appears from the key fob diode;
• quickly click on the key with the speaker crossed out.

Additionally, you can program the locking of doors and trunk lid.

Need to reprogram Tomahawk 9030 key fob

It is often necessary to update the firmware of remote alarm devices when they refuse to arm. The procedure for reflashing Tomahawk key fobs is presented below.

1. To flash the alarm remote control, first activate the ignition. Don't start the engine.
2. Press three buttons at the same time: “Opening the luggage compartment”, “Crossed out loudspeaker”, “Service mode”.
3. The siren should emit five beeps.
4. Release all buttons.
5. Press again on the “Trunk” and “Crossed out loudspeaker” signals. Correct completion of all points will be confirmed by the blinking of the car’s turning lights.

Button combinations

The factory instructions contain information about 19 possible combinations on key fobs. However, there are keyboard shortcuts that drivers use most often:

• hold the key for 2 seconds + open the cargo compartment – ​​immobilizer;
• key + siren – automatic activation of security;
• double click on Zz – work with shock sensors;
• quick click on “Zz” – activate full car protection;
• The key is to turn off the alarm.

More detailed information can be found in the factory instructions.

Self-programming of the new Tomahawk remote control

Setting up a switch for the Tomahawk family of alarm systems is not particularly difficult. Almost all communicators in this line operate at a radio frequency of 433 MHz. To program the key fobs, turn the ignition to the on position, but the engine does not start.

Keep the OVERRIDE mode button pressed until the security system emits 4 beeps. Then the settings key is released and at the same time press the keys on the key fob marked “trunk opening” and “sound control”. They must be held until the siren sounds.

For the first remote control the signal should sound once, respectively for the 2nd, 3rd, 4th - 2, 3 and 4 times. In order for the key fobs to record the code, you should not take any action for a certain amount of time, depending on the model.

It should be noted that some key fobs are interchangeable. For example, the Tomahawk 7010 remote control is compatible with TZ-9030, TW-9020, TW-9030, LR-1010LC, TW-4000 communicators.

The principle of registering key fobs

Regardless of the type of alarm, programming is performed via the Override button. To do this, enter the programming mode and follow the sequence of actions described in the factory instructions.

Features of programming the Tomahawk alarm remote control of different models

Key fobs from different alarm series are recorded in the device memory in different ways. For models 4000, 7020, 9020, 1010, 9030 the procedure is relevant.

1. Turn off the ignition.
2. Click on Override the required number of times.
3. Turn on the ignition.
4. Enter a specific combination on the key fob.

At the same time, it should be borne in mind that regardless of the model, if the key fobs are not registered during their programming, they will be forgotten by the system and lose their relevance.

Programming additional key fobs

On the most common modifications of devices, registering additional remote controls occurs as follows:

• turn on the ignition;
• hold Override;
• wait for the system response in the form of 4 chirps;
• enter the required combination on the remote control.

This way you can register additional control panels.

How to block buttons

Locking the key fob controls is a necessary option to prevent unintentional manipulation of the alarm. Typically, this function is needed when carrying keys in your pocket.

You can activate the protection by simultaneously holding down the keys with the key pattern and F. To unlock the key fob, the steps are performed in the same way. If everything is done correctly, the pager beeps once and the module can be used.

Compatibility

The interchangeability of Tomahawk TW 9030 car alarm key fobs is complete exclusively with models of the same brand:

• TZ 7010;
• TZ 9020.

Device remote controls can work properly with the specified security systems, without the need to replace the main modules.

Analogues from third-party manufacturers should be used with caution. Otherwise, the purchased pager may not work correctly or may not transmit a signal at all.

Linking a new key fob without the old one

The new Tomahawk TW 9030 alarm remote control is connected using the Valet button, located in a secret place, usually under the steering wheel or in the glove compartment.

1. Press the Valet button seven times without turning on the ignition.
2. Turn on the ignition. Seven beeps should sound indicating entry into the programming system.
3. Take the main remote control and hold the “Open” and “Close doors” keys on it. Security will sound a beep. The first keychain is attached. Following the same instructions, you can program the second one. Only two CHIRPS will sound.
4. Turn off the ignition and exit programming mode. The parking lights should blink five times.
5. After ten seconds of inactivity, the system will automatically exit maintenance mode.

How to turn off a car using the Tomahawk 9030 key fob

The manual contains information about remote starting and stopping the power plant.

You can enable the mode like this:

• hold down the element with the key shown;
• there will be a trill from the key fob;
• quickly click on the indicated key.

The indicator on the antenna will light up. The extension is disabled using a similar sequence of actions.

Tomahawk tw-9030 instruction manual, I. basic system functions, Basic system functions

Tomahawk tw-9030, Manual, Operation i. main functions of the system

• Image
• Text

TOMAHAWK TW-9030

MANAGEMENT

By

OPERATION

I. Basic functions of the system.

•Anti-grabber •Anti-suner •Feedback •Security of doors, hoods, trunk 1K1 and ignition systems •

I'll block the engine

•Additional engine blocking •Built-in immobilizer •Individual PIN ID •Emergency disarming •Silent disarming •Automatic arming •Automatic re-arming •Gran mode with the engine running •Two-step activation of the gran mode •Two-level shock sensor •Built-in central locking •Programmable central locking pulse •Control of central locking when the engine is running •Built-in engine blocking relay •Built-in relay for parking lights • 1 additional unit (programmable) •Delay of interior lighting •Posting backlight function •Temperature sensor •Connectability systems "comg^zort" •

Possibility of connecting a paid horn

•About the faulty zone •Protection against false alarms •Status memory •Trigger memory •Indication of system status by LED indicator •Panic mode •

Valer mode

•R"Kim "Antì-Hljack" •Mode "tui" "qxiHM" •Remote switching off/on the siren •Remote zone-by-zone shutdown of the shock sensor •Programmable key fobs •Information about programmed key fobs •

Keychain pad with LCD

•Visual and audio confirmation of functions performed •

Visual indication of all triggers and system status

•PoASvetuz LCD •

Built-in clock

•

Built-in timer

•

Built-in alarm clock

•Indication of battery charge level •Vibration mode •Battery energy E1TONOMY mode •

Locked 1TO buttons 6 relo1 "z-pad)yura

•Increased range of 6relo1to-paid>ura up to

1200

m (depending on external conditions)

•Remote system state changes on all programmed key fobs •Safe driving function •Search for a car •Remote trunk release •Warning function about an open door during double-union •

| temperature control in the cabin o/m

•Protected remote engine start/stop •

Hourly automatic engine start

•Automatic engine warming up at a given temperature •Possibility of connecting the start function to a vehicle with an automatic or manual gearbox •Possibility of connecting the start function to a vehicle with a gasoline or diesel engine •Turbo timer

Tomahawk 9030 does not respond to the key fob and does not open

If the signaling system does not see the key fob, the reasons may be superficial:

• batteries or battery are dead;
• The transmitter antenna does not work;
• mechanical damage to the device;
• water ingress.

To eliminate problems, you need to change the batteries and diagnose the equipment for breakdowns.

Why is the remote control not programmable?

There comes a time when the car alarm stops working correctly: the car is neither armed nor disarmed. The remote control does not transmit the code over the communication channel well and, accordingly, does not perform various actions. Attempts to connect the key fob to the TZ 9030 alarm system lead to nothing. Below is the procedure if the remote control is not registered.

1. Find the instructions for the model of security system installed on the car.
2. Carefully study the procedure for programming remote controls. Follow all steps described in the instruction manual again.
3. If you haven’t found the documentation, look for information on the Internet. There are many videos from which you can find instructions for activating the Tomahawk 9030 key fob.
4. Understand the reasons. Perhaps the system does not send or receive signals due to mechanical damage. Carefully examine all components of the security system. Take the time to check the contacts on the transceiver and control module connectors. Test the electrical circuits with a tester. Replace damaged wires with new ones. Clean off any oxides on the contacts.
5. Nothing works. Diagnose the control module. It may need to be re-flashed. This work should be entrusted to specialists.

What can break in an additional remote control?

There is essentially nothing to break in the spare key fob. However, users highlight some problems:

• The battery runs out quickly;
• the flimsy body cracks when pressed;
• Buttons may stick.

If a fault is found in the circuit or antenna, repair is not cost-effective - it is cheaper to buy a new transmitter.

How to distinguish Tomahawk 9030 and 9010 key fob: difference

External differences between the Tomahawk TW 9030 and 9010 remote controls are almost invisible. Both models have an LCD display and an equal number of keys. Their location is also similar.

The only difference is the area of ​​responsibility of the buttons, as indicated by their markings.

Everything is more complicated inside. Differing schemes guarantee a complete lack of compatibility between devices.