StarLine E91 alarm system with auto start (key fob operating and installation instructions)

The Starline E91 alarm, released in 2013, caused considerable confusion due to its markings - while looking like the same age as the A91/61, it was actually two generations newer. StarLine E91 is already a modular alarm system with a 2CAN module pre-installed in the central unit - it is closer to the A94.

Specifications

The Starline E91 anti-theft system has the following technical data:

the frequencies at which the system components operate are 433-434 MHz;
transceiver type - 128-channel transceiver;
the range of action of the main key fob when operating in command mode is 500-800 m;
the distance at which the communicator can receive signals supplied by the head unit is 2000 m;
range of the auxiliary key fob - 15 m;
sensitivity controller type - three-axis sensor;
operating temperature range - -50...+85 °C;
type of power source of the head unit - on-board network with a voltage of 9-18 V;
the amount of current consumed by the basic anti-theft device is 18 mA;
the amount of current used by a system equipped with additional modules is 25 mA.

Equipment

The standard delivery package for the Starline E91 car alarm includes the following elements:

head device;
auxiliary relay with blocks - 3 pcs.;
main keychain;
power supplies for communicators - AAA batteries;
transceiver with built-in antenna module;
emergency button;
LED element used to assess the state of the security system;
limit switches with mounting hardware;
LED elements type 1N4007 - 4 pcs.;
adapter for connecting additional sensors;
installation kit, including a central cable harness with a connector, auxiliary cables with terminals, wires for connecting the antenna unit and sensors;
plastic ties;
operating instructions, technical data sheet of the product and warranty card.

Functions

Maximum vehicle protection against theft is made possible thanks to the following functions:

blocking the fuel pump, ignition switch and vehicle control unit;
protection of opening elements of the car - doors, trunk, hood and fuel tank cap;
control of the handbrake lever and pedals;
evacuation protection using shock sensors that respond to changes in body position.

Additional features include the following options:

automatic engine start, carried out by user command, specified time or engine temperature;
control of adjustable interior elements;
silent activation of security mode;
saving user settings;
synchronization with a smartphone (if an additional module is installed).

Methods of protection

Starline key fob alarm with auto start: models, operating instructions

The system ensures protection of vehicle zones using various control methods:

When protecting the engine, the circuits of the fuel pump, ignition and control unit are blocked. Additional protection can be provided by installing Starline R3/R4 code controllers or digital R2 (operates via radio signal). All additional controllers are fully compatible with the head unit.
Protection of opening body elements (doors, gas tank, hood or trunk lid) is carried out according to signals from standard or additional limit switches.
Additional security is provided by monitoring the brake pedal switches and the parking brake lever.
To protect body panels and windows, a shock sensor with a built-in tilt indicator is used. The device has two stages for measuring impact force. For minor impacts, the sensor triggers short warning signals with a siren. If there is a strong impact, it activates the alarm mode.

How to install

For Starline E91, the installation instructions require the following steps:

Installation of the head unit. It is placed under the dashboard so that it can receive user commands from the key fob. Before installing the device, remove the decorative interior trim. The head unit is installed on a flat surface, secured with plastic ties or self-tapping screws.
Siren installation. The part is mounted so that the wiring is protected from moisture. It is recommended to turn the horn down.
Transceiver installation. The transceiver is placed on the windshield or rear window. Before starting work, wipe the surface with a degreasing compound. The device is secured using double-sided tape or glue.
Installation of an emergency button. It is mounted in a hidden place and covered with electrical tape.
Sensor placement. The parts are installed on flat surfaces. There should be no plastic or rubber layer between the body and the sensor.
Installation of limit switch. This part of the system is mounted on the hood.

Connection diagrams

The Starline E91 car alarm is connected according to the following scheme:

Providing grounding. The end of the ground cable containing the terminal is connected to the standard body nut.
Connecting the positive terminal to the power circuit. If necessary, the head unit is connected to the positive terminal of the battery using an additional fuse.
Relay connection. The protective device is connected by inserting the positive terminal. The relay and the head unit must be connected to different circuits.
Connecting alternate control connectors. The door lock circuits are connected to output X3.
Connection of the ignition and immobilizer wiring harness to outputs X3 and X4.
Limit switch connection. The cable leading to the device is inserted into connector X4.
Connecting an emergency button to output X8.
Connecting a siren. The cable of this part of the system is connected to connector X1.
Connection of the blocker bypasser to connector X1.
Connecting auxiliary controllers to output X4.

User manual

The E91 operating instructions require initial setup. The key fob is supplied with a battery before starting work. Binding of the communicator is carried out by repeatedly pressing the emergency button. After turning on the ignition, the system gives 7 short signals. By holding down buttons 1 and 2, the key fob is synchronized with the head unit. Programming of basic functions is performed using the cursor method. The car alarm instructions, which we recommend printing, will help you determine the meanings of the indicators.

Autostart

The Starline E91 alarm system with auto start is controlled in the following ways:

By command. To start the engine, press button 1 on the key fob. To turn off the engine, hold down button 1. At the same time, briefly press button 4.
Periodically. The cursor is moved to a clock-shaped indicator. After this, press button 1. The system will emit a sound signal, and the display will show the time remaining until the engine turns on.
By timer. The cursor is directed to the hourglass-shaped indicator, after which the 1 key is pressed. The timer parameters are set using the 1 button of the communicator. Each press increases the value by 2 hours. Save the settings by holding down key 1.

How to program

The programming table presented in the instructions will help you make the necessary settings. The desired parameter is selected by hovering the cursor over the corresponding icon. To change the value, hold down button 1 and briefly press button 2. The settings menu in Starline E91V is automatically exited after 10 seconds of inactivity.

Temporarily disabling sensors

When the car is armed, you can turn off the alarm sensors at any time (for example, during a severe thunderstorm or fireworks).

To turn off the shock sensor, quickly press button 2 twice. This will turn off only the warning level of the shock sensor. To disable the alarm operation, press button 2 twice again. The shock sensor will turn on automatically the next time you arm it, or you can turn it on yourself by the same double press on 2.

To disable or enable the tilt sensor, press button 2 twice.

Controlling the Starline A91 alarm using key fobs

For Starline A 91 alarms, the duration of key presses on the communicator is important:

Short-term - one “click” on a button lasting less than 0.5 seconds.
Long lasting. The user must press and hold the control until the remote control emits a melodic beep.
Double. Two quick “clicks” on one key for 0.5 s.
Consistent. The user presses one or more keys twice. The first “click” on the control should be longer, and the second should be short.

Identification of controls on the main and additional consoles

Video: controlling the Starline A91 key fob buttons

Filmed by the channel “REALAUTO”

Indication of modes and functions

Designation of icons on the key fob screen:

Automatic start of the car engine by alarm clock is activated or disabled.
The motor autostart mode by timer is enabled or disabled.
Automatic remote start of the vehicle engine based on air temperature is turned on or off.
Anti-theft complex service mode icon.
Engine turbo timer icon.
Option to automatically activate protective mode.
The machine's engine lock function is disabled or disabled.
The key lock on the remote control is enabled or disabled.
Car engine temperature indicator.
An icon indicating the charge of the battery installed in the remote control. If the indicator blinks and there is one division left, the battery must be replaced.
Car engine turned on icon.
The vehicle anti-theft mode is activated.
An icon demonstrating the connection of an additional Starline M20 or M30 GSM module.
Luggage compartment open indicator.
One or more vehicle doors are unlocked.
The engine compartment of the car is open or not completely closed.
If this icon appears together with the inscriptions DATE 1 or DATE 2, this indicates that the warning level of the main regulator for fixing physical impacts or an additional controller has been bypassed. If there is a marking SH1 or SH2 next to the indicator, we can conclude that the first zone of one of the regulators has been activated.
A display with the current time, which also displays the temperature level for autostarting the engine, setting the timer and alarm clock.
The alarm timer is activated.
The system's alarm function for autostarting the engine is enabled.
Indication of communication quality.
The vehicle locks are open.
The door locks are locked.
Vehicle protection mode with acoustic signals is activated.
The car security function is activated without using siren sounds. Information about the activation of the alarm mode will be displayed only on the display and will be displayed through visual alerts or audio messages.
The vehicle's handbrake is not applied or the brake pedal is depressed.
The mode for activating or disabling the security mode when using a personal password is enabled.
Indicator of the enabled operating algorithm with a manual transmission for automatic engine start.

Designation of icons on the key fob display

Table: setting up the main key fob function menu

1 melodic signal;
1 short;
2 short beeps

To quickly increase or decrease the clock values, you can hold down the corresponding communicator controls.

To quickly increase or decrease clock parameters, you need to hold down the corresponding remote control controls.

To quickly increase or decrease clock settings, hold down the corresponding controls on the main communicator.

To quickly change values, these controls must be held down.

Meaning of the icon on the screen

The display located on the main key fob simplifies the procedure for using the alarm and displays:

transceiver status;
information about the current time;
shock sensor operating mode;
status of the cellular or satellite communication module;
information about the selected operating mode (with or without sound);
information about the selected method of automatic engine start;
information about the battery charge level in the communicator;
data on the state of security zones;
information about activating additional functions.

The display shows the status of the transceiver and information about the selected operating mode.

When an alarm is triggered, the screen displays the zone that triggered the siren (for example, a shock or tilt sensor, a door or hood limit switch).

Initial alarm setup

The official manual for Starline A91 Dialog states that before programming and setting the settings, you need to link the communicator to the control unit installed in the car. Additionally, the initial setup of the security system includes programming a personal code and recording codes for digital radio relays for engine blocking.

Recording key fobs in the complex memory

In accordance with the Starline A91 instructions, the procedure for programming communicators is as follows:

To start using the anti-theft system, you need to install a working battery in the control panel. The battery is inserted into a special compartment hidden behind the rear protective cover.
On a car with the ignition system turned off, press the button to enter the service mode seven times.
In the ignition switch, turn the key to the “ACC” position to turn on the system. The siren should emit seven sound pulses, which indicates successful entry into the remote control programming mode.
On the control panel, press keys 2 and 3 simultaneously. These controls must be held until the siren sounds once. This indicates successful programming of the device.

The Starline A91 alarm system allows you to enter data about no more than four communicators into the control unit’s memory.

Entering the main menu for programming functions

To enter the settings menu for security and service options of Starline A91 Dialog, as well as engine starting parameters automatically, you need to perform the following steps:

When the ignition is turned off, the button to enter the service mode is pressed five times if the service and security options are being configured. In the case of autorun, the number of clicks should be 6 pcs.
The ignition is activated. The siren should beep five times, indicating that you have entered the setup menu.
Using the service key, you select a function (the number of presses on it must correspond to the option number). Each number of the specified function is indicated by flashes of the LED light and sound pulses of the siren.

Table: programmable security and service functions

Table: programmable trigger functions

Personal code programming

The procedure for setting up a personal password is as follows:

You enter the options settings menu, then you need to select one of the emergency deactivation code methods. To complete the task, you must enter the function programming menu 9. An indicator with the inscription “Pin Code” will appear on the communicator screen.
You enter the personal password setting menu. When the ignition system is turned off, the button to enter the service mode is pressed four times. With each “click” on a key, the diode light comes on.
The ignition system is turned on. The siren should sound four times.
The button to enter the service mode is pressed once. If the control unit successfully enters the menu for setting the first digit of the password, the siren of the anti-theft system will emit one sound signal.
Over the next five seconds you need to enter the first digit of your personal password. Short presses on the first, second and third keys assign the code values 1, 2 and 3, respectively. When assigning a symbol, the siren will sound the corresponding number of signals. When you press the first, second or third key twice (first long, second short), the password is assigned values of 4, 5 and 6, respectively. Symbols are assigned in a similar way for the second and third characters of the code, if it is two or three digits.
To exit the programming menu, you must turn off the ignition system. Also, the exit will occur automatically if the user does not take any action to configure for ten seconds. External lighting devices should give five light signals.

Recording digital engine locking radio relay codes

If you additionally install a digital relay, it must be configured when the security mode is disabled:

At the first stage, the operating mode of the device is selected. If the contact type should be normally closed, then the loop on the body of the part is preserved; if it is normally open, then it is cut.
Enters the options settings menu. In accordance with the operating mode of the digital relay, method 3 or 4 of the tenth option is selected. After this, the function programming mode must be turned off.
Then the conductors in black insulation of the recordable devices marked GND are connected to any standard “ground” bolt screwed into the body.
The button to enter the service mode is pressed seven times. The ignition system in the car should be turned off at this stage.
The ignition is turned on. The siren should beep seven times, indicating successful entry into the settings menu.
Over the next five seconds, the black radio relay cable marked VCC is connected to the ignition system power line. If the Starline DRR relay is successfully programmed into the control unit’s memory, the siren should emit one extended beep. The remaining devices are linked in the same way.

PIN code programming

Setting a key fob PIN code for emergency alarm deactivation is necessary, as it seriously increases the security of the system. In Starline E90, this code can consist of 1,2 or 3 digits from 1 to 6, that is, a total of 258 different options are available.

The factory default value of the pin code is 3, which is also set after resetting to factory settings. It is impossible to erase the PIN code separately on the E90.

To set a PIN code, you must first set its length in the alarm settings (see below), then with the ignition on, press the Valet service button four times. Then turn on the ignition and enter the first digit of the code:

Code digit	Buttons
1	1
2	2
3	3
4	1 long, then short
5	2 long, then short
6	3 long, then short

If you selected a two- or three-digit PIN code in the settings, repeat these steps for subsequent digits.

Equipment and characteristics of the Starline A91 alarm system with auto start

When purchasing a Starline A91 alarm system (the price of the device varies between 3500-4000 rubles), the motorist receives a whole set of additional equipment, which includes:

Instructions for installation and use of security;
Two branded key fobs (main, with LCD screen and spare);
Replaceable battery;
Control module;
Antenna;
Shock sensor;
Standard case;
A set of wires for connecting component parts (we will look at how to connect an alarm system to a car later in the article);
Sensor for the engine compartment;
Temperature meter;
Service key (where the jack button is located on the Starline A91 alarm system and how to use it, we will tell you in detailed instructions below).

After installing the listed components on your car, the owner can use the presented device not only as sound or silent security, but also for:

Central locking control;
Warming up the engine and interior (we will find out a little later how to set the automatic engine start time and indicate the required heating temperature);
Immobilizer settings.

At the same time, the device is capable of capturing the signal from the key fob in 4 channels, at a distance of 700 to 1500 meters. And to power it, 25 mAh is enough, which can be obtained from a 12-volt battery.

Checking the vehicle's condition

Regardless of the security status, the owner can always find out the battery voltage, engine temperature and vehicle interior. By briefly pressing button 3, you will first see the voltage value, which after a second will be replaced by the temperature readings in the cabin. The temperature sensor is installed in the StarLine E90 central unit, and the temperature value may vary depending on the alarm installation method.

To find out the engine temperature, you need to press button 4 twice.

If the measured temperature is outside the display range or the sensor is faulty, the indication will be “—” (temperature too low) or “—” (temperature too high).

Something else useful for you:

Setting up the key fob and labeling the buttons

On the body of the StarLine A91 alarm key fob there are three main buttons that are responsible for setting up the entire security system. Well, how to activate the desired option using them, see the table below:

It is worth noting that the “Valet” button is located not on the key fob itself, but in the interior of the car, so that it is not noticeable. But if the battery is discharged, or the door is opened with a key (without first resetting the alarm from the key fob), it becomes the only salvation for the car owner. After all, when it is pressed, the security system automatically switches to service mode, which gives the driver the opportunity to get to home or to the nearest service station.

In addition to the listed options, the operating instructions for the Starline A91 alarm also provide additional functionality, which is activated by combining two buttons:

1 and 2 keys (sequentially) – activation of silent alarm;
1 and 3 keys (alternately) – manual start of the engine (with the internal combustion engine already running, the combination of these two buttons extends the set timer twice);
3 and 2 keys (sequentially) – turn on the second channel;
1st and 3rd key (simultaneously) – key fob locking;
2nd and 3rd key (simultaneously) – unlocking.

We will look at how to attach the key fob to the Starline A91 alarm system after installation on the car in the article below.

Flexible configuration

A serious advantage of the E91 is the use of flex channels, which can be freely programmed both by activation event and by operating algorithm. Thanks to this, the alarm adapts to cars where additional connections are needed for the correct operation of the security system (like the simulation of opening the driver's door mentioned above), and is able to implement comfort functions.

In this way, the system is connected to the pre-heater, one of the flex channels is programmed to control it, the folding of the mirrors is configured after arming, and so on. One of the four additional channels is activated from the mobile application; this channel is selected in the service menu of the central unit.

When setting up each additional channel, the following are programmed sequentially:

Delay from the moment of activation to the first pulse (from 1 second to 999).
Duration of the first pulse (up to 998 seconds; when set to 999, the additional channel is turned on for an unlimited time until a shutdown event occurs).
Delay until the second pulse is given, unless set to unlimited in step 2.
Duration of the second pulse (same as setting the first).

Setting any step to 0 means skipping it.

Events for turning an additional channel on and off are set from a rich set of options and can be combined. We configure the additional channel to trigger when the central lock is closed and the ignition is turned off, when the engine is turned off with the key, and when it stops at the end of the autostart. Up to three conditions are used simultaneously.

Alarm systems are used to create simple anti-theft systems on cars. However, its architecture makes it impractical to install on cars that require power control of the central locking (since there are no power outputs to the actuators), and cars that use a LIN bus that is not supported by the system. Functions related to the LIN bus will have to be implemented via analog connections. The disadvantages of the system include the impossibility of keyless bypass of the immobilizer on your own.

Pairing a security system with a key fob

We have already found out how to turn off the Starline A91 alarm using the jack button and using which key combination to start the engine. But before you give commands to the device, you need to bind it to a branded key fob. And this is done as follows:

The same conjugation instructions, paired with a connection diagram for the Starline A91 alarm with auto start, should be present in the list of component parts of the device.

Well, if you don’t have one, then you can use the analogue attached above.

Setting up additional features

Previously, we found out that the StarLine A91 alarm system has auto-start functions based on a timer and engine temperature. Here's how to set the required engine start mode:

By timer – key 3 is pressed once, after which the current timer value (from 2 to 24 hours) appears on the LCD display of the key fob. In order to increase it, just press button 1. But button 2 is responsible for decreasing the reading;
For temperature – key 3 is pressed twice so that the icon with a thermometer flashes on the LCD display of the key fob. Well, you can set the desired temperature mode in the same way as in the case of a timer: button 1 - increase the value, and button 2 - decrease it.

But before you set up the Starline A91 alarm to autostart based on temperature or timer, you need to set the time on the key fob in advance. And this is done again with key number 3, which must be pressed until the device makes a characteristic melodic sound.

StarLine E91.1

A trip is possible only after entering an individual PIN code using the standard car buttons. The option is available when integrating a 2CAN or CAN+LIN interface 3D shock and tilt sensor Integrated digital shock and tilt sensor with remote adjustment registers jacking and evacuation of the vehicle Telematics (optional) Integration of optional GSM-GPRS, GPS-GLONASS telematics interfaces allows you to remotely control the security of your car and carry out monitoring Control from your phone (optional) Integration GSM interface allows you to manage security and service functions, receive notifications about the security status on your mobile phone Free monitoring (optional) Using simple and convenient monitoring www.starline-online.ru you can accurately to find out the location of your car up to a few meters. The option is available when connecting to StarLine

Alarm systems Starline E90 with auto start (operating and installation instructions)

Signal reception is possible from a distance of up to 2 km.

The spare pager works within a radius of 15 m.
The model is equipped with an ultra-sensitive sensor that operates using three-axis integrated technology.
The optimal temperature range at which a car alarm can operate varies from -50...+85°C.
The voltage used as a battery is 9-18 V.
The key fob is equipped with AAA batteries.
The exact range of the E90 is determined by a variety of factors, including current weather and interference.
The Starline E90 alarm system is sold in the following configuration:
1. User manual and document confirming warranty service.
Step-by-step instructions for installing and further operating the system. It allows you to install security devices and configure them yourself.

There are two levels of long press: Long press first level - long press the button until the first beep; Examples:

— long press of the first button;

— long press of the first and second buttons; Long press second level - long press the button until the second beep; Examples:

- long press of the fourth button

StarLine E91

EXTENDED TEMPERATURE RANGE StarLine operates confidently in harsh climatic conditions at temperatures from -50 to +85 °C AUTO START Intelligent auto start allows remote and automatic engine start based on temperature or at a specified time RECORD ENERGY ECONOMY Record StarLine energy efficiency guarantees the preservation of sufficient battery charge for up to 60 days per day security mode thanks to the use of patented advanced technologies and software solutions CONTROL FROM YOUR PHONE The optional GSM module allows you to control security and service functions, as well as receive notifications about the security status on your mobile phone INTEGRATED 2CAN INTERFACE Ensures fast, convenient and safe installation of StarLine security systems on modern vehicles equipped with CAN buses COMMUNICATION CHANNEL CONTROL Automatic

Characteristics of the Starline E91 alarm system: how to install it and use it correctly?

If there is no compliance, the user will have to reprogram the engine control unit themselves. If the signal in the area is unstable or there is interference, this will reduce the range of the communicator. In addition, such a problem will cause increased current consumption by the security system. Technical parameters of the anti-theft system: Technical parameter Value, measured in amperes (A) Siren 2 Lighting devices installed in the turning headlights on the left side 7.5 Bulbs installed in the left turn signals 7.5 Actuating mechanisms of door locks 15 Alarm electric circuit for controlling locking products 0.2 Ignition system 25 Electric lines for connecting additional devices and equipment 25 Power circuit for the starter mechanism 25 Electric lines for blocking the power unit control module 0.2 Blocking the power unit using a separate

StarLine E91: operating and installation instructions

However, the capabilities of the Starline E91 are sufficient for comfortable use in the city, with the exception of crowded parking lots near shopping centers in big cities.

There is the possibility of telematic control when installing an additional StarLine GSM beacon in the central unit or an external GSM beacon, for which a special connector is provided.

The alarm system offers the following methods of blocking the start:

External blocking relay included in delivery. Programmable as either normally closed or normally open. Radio relay StarLine R2 (not included).

The built-in CAN module does not require triggering via the CAN bus.

Thus, the start blocking methods included in the delivery set are primitive, and when the car is physically opened, the level of security of the system cannot be called satisfactory: an acceptable level of protection will require, at a minimum, the purchase of a radio relay.

E91 has the ability to control: doors, hood.

Technical specifications – Operating instructions SsangYong StarLine E91 Dialog

2 A • connection of light signals. 2 x 7.5 A • central locking control. 2 x 200 mA • ignition switching on.

25 A • inclusion of accessories. 25 A • starter activation. 25 A • engine blocking (black-red wire of connector X1).

Megacity Mode

This mode is no less important for the slave system. Indeed, using this mode, you can easily increase the range of operation and sending of alerts to the slave system. You can find out how to switch to this mode from the instructions. The instructions are included with the protection system itself. You need to know that before using the slave system directly, you need to thoroughly familiarize yourself with the instructions. There are two sensors on the sensor itself, with the help of which you will know about the stage of impact on your vehicle.

Typical connection diagram StarLine E91

How to set the time on a Starline E91 key fob

Operating instructions for SsangYong StarLine E91 Dialog

Liquid crystal display of the key fob .22 Indication of active modes and functions .22 Indication of the status of the car alarm and vehicle .23 Menu of the functions of the main key fob .24 Programming operating modes using the cursor method .27 List of modes programmed using the cursor method .29 Security and anti-theft functions of the car alarm Arming with sound signals confirmation .30 Arming without sound confirmation signals .31 Activating silent alarm mode .32