Alarm KGB tfx 5 with auto start: 7 main characteristics, installation and operating instructions

Key fob with feedback and LCD display for KGB FX-5 alarm system. AAA battery included. Programming is a gift!

How to program the KGB FX-5 alarm key fob

• Turn on the ignition.
• Press and hold the Valet service button until 4 siren signals appear.
• To record the main key fob with display, press buttons 1 and 2 of the key fob simultaneously. To record an additional key fob without a display, press buttons 3 and 4 of the key fob simultaneously. Successful recording of the first key fob into the system memory will be confirmed by 1 siren signal.
• Repeat step 3 for all recordable key fobs. The interval between recording each key fob should not exceed 5 seconds, otherwise the alarm will automatically exit the key fob recording mode. Successful recording of each key fob is confirmed by the corresponding number of siren signals.
• Turn off the ignition. To confirm exit from the key fob recording mode, 5 flashes of dimensions will follow.

the KGB FX-5 alarm memory . Key fob codes are recorded when the security mode is turned off. When recording new key fobs, you must also rewrite the old ones, otherwise they will be deleted from the system memory.

Typically, car security systems, when used properly, do not cause problems for their owner. But it happens that these devices also work intermittently. The most vulnerable part of the alarm system is the remote control. It is easy to drop, lose, and finally, it can fail due to “old age”, the buttons no longer respond well to pressing, the body is worn and cracked, the display is broken.

There is a solution, buy a new remote control. Finding it sometimes takes considerable time, for example, if the model has not been produced for a long time. Also, the price at different retail outlets sometimes differs significantly. I advise you to buy keychains in specialized stores with a manufacturer's guarantee, since you can often stumble upon a Chinese counterfeit, although they also work, but you take them at your own peril and risk; of course, no one gives a guarantee of their long-term operation.

Some key fobs are interchangeable with each other, naturally only from one manufacturer's line. With such a replacement, some alarm functions may not work, such as auto start and temperature readings. Therefore, still try to purchase “your” keychain. You can see the interchangeability here: It is impossible to use the key fob immediately after purchase; it needs to be registered (connected) with an alarm system. Installers of additional equipment charge from 200 to 500 rubles for this. Here I will tell you how to save this money by doing this simple operation yourself. The whole process will take no more than two minutes, provided that you are prepared for it. The first thing you need to do is find the “valet” service button in the car interior.

It is located under the front panel or in the fuse box and usually looks like this:

Possible button locations:

The recording procedure for different types of car alarms is somewhat different, so let’s look at each of them in more detail:

The instructions for the KGB anti-theft system consist of several pages. Only after carefully studying it can you fully use all the alarm functions. One of the important sections is programming the transmitters (you can record up to four remote controls). But if, after reading the instructions, you still doubt your actions, then let’s figure out together how to set up the KGB alarm key fob.

Programming the new KGB remote control with feedback

Replacing a broken communicator KGB GX 3, FX 3, G 2, EX 7 implies recording it in the memory of the control unit. For this.

• Turn the ignition key to the “On” position.
• Press the Jack key and hold it for six seconds. After four beeps sound, release the service button.
• Press keys 1 and 2 at the same time. The siren will emit one squeak.
• Enter the codes of the remaining transmitters in the same way. Programming each remote control is accompanied by a corresponding number of sounds.
• If you do not press the buttons on the key fob within six seconds, the control unit will exit the setup mode. The lights will flash five times.
• Deactivate the ignition.

Remember that when recording new pagers, do not forget to re-register the old ones in order to avoid their deletion from the system memory.

This is interesting: When to change spark plugs on a car

Setting up autorun from the KGB key fob

You can start the engine from the alarm switch KGB FX 5, G 5, FX 10, GX 5 RS, F X 8, FX 7 (fix 7) in two ways.

• Move the cursor to the “START” symbol and press button 2.
• Press key 1 for three seconds. The engine will start. The side lights will flash three times and a melody will play on the key fob. The LED will light up continuously.
• The screen will display the “Smoke from the exhaust pipe” symbol and the set engine warm-up time (5, 10, 15, 20 minutes).
• One minute before the end of warm-up, r01 will appear on the display, a sound signal will follow, and the side lights will light up four times.
• After stopping the engine, the message r00 will appear on the screen, and the “Smoke from the exhaust pipe” symbol will disappear.

To program autostart of the engine based on temperature, do this.

• Move the cursor to the “START with thermometer” icon and press button 2.
• The siren will sound once, the side lights will work once, and a melody will play on the remote control.
• The “Thermometer” symbol will be displayed on the screen, indicating that autostart is activated based on degrees outside and the temperature value (-5, -10, -20 -30). The LED will flash.
• To turn off automatic start based on temperature, move the cursor to “START with thermometer” and hold down button 2. The siren will sound twice, the dimensions will blink twice. A melody will play on the pager. The Thermometer symbol will disappear.

We also have instructions for using the Sheriff aps95lcd b4 keychain.

Instructions for registering old remote controls

Activation of the anti-theft system switches KGB VS 5000, MX-9, ex 8 series, VS 4000, tfx 5 (tfx 5), ex 7, VS 130, AX-5 begins with entering the programming mode.

• Activate the ignition.
• Triple-click the Valet button to pair the remote with a one-button configuration.
• Click on the “Valet” key six times to record a two-key fob.
• The siren will sound once. You have entered setup mode.

Follow the instructions below to record pagers.

• Press any key on the first remote control. One signal will play.
• Press any button on the second remote device. The siren will sound twice.
• Following the previous steps, register the remaining transmitters.
• Exit setup mode by turning off the ignition or without pressing anything for fifteen seconds. The system will confirm exit with three siren signals.

Advantages of the gadget

The security system interacts with the unit through two-way communication. A remote messaging function is provided.

Basic alarm modes: “Standard” and “Silent”.

The operating range of the device depends on the regulations for use, as well as the terrain. For the vehicle control function, this parameter should not exceed 600 m. When notified, the device operates at a distance of up to 1200 m.

The number of security zones is 6 (doors, hood, trunk, ignition, brake). The number of programmable channels is 4 (No. 1 is for the trunk, the rest are independently configurable).

The developers of the device guarantee absolute protection from attacks by intruders in 3 cases: when intercepting, decrypting and recoding the signal.

The system meets safety requirements, as stated in the quality guarantee.

Why doesn't it get attached?

Flashing key fobs for the KGB security system VS 100, 5500, 200, 5900, 300, 5700, 400, 250, 500, BC 150, tfx 7 is not always successful the first time. Why can’t you reprogram the remote control and how to get out of this situation.

• Service mode was accidentally activated. Turn it off by pressing the “Valet” button and repeat the firmware procedure.
• The “Ignition activated” command is not detected by the alarm control unit. Contact a service station.
• Switch failure. Repair it yourself or take it to a specialist.
• Failure of the control unit. Take the car to a service center.

Find out everything about identifying the Sheriff alarm model from photos of key fobs.

FakeHeader

Comments 17

Please tell me again in detail how to register the key fob? I have the same KGB. Tell me in detail what to click? what to enable? What on the key fob needs to be activated and pressed? Please, I really need it! Thanks in advance !

I do not remember. Read the instructions.

To register, you don’t have to hold it down, but press it 4 times

It seems that the only reason was that the valet mode was activated on the key fob.

A good signal master and not expensive. On Serov you go down and on the Tolstoy Lev to the right a little to the bottom and there will be the 1st turn to the right, I don’t remember the name of the street, you go a little and on the right there will be a house with a garage, the gates are either blue or green. written phone number or signaling, contact him, he's a decent guy.

How to set the time on a KGB key fob

Setting the clock on the KGB anti-theft system remote control begins by entering the installation mode by pressing and holding the “SET” button.

• After one second, a short signal from the transmitter will follow. The screen backlight will turn on for five seconds.
• Continue holding the SET key.
• After two seconds, two beeps from the key fob will sound. You have entered the current time setting mode.
• Release the SET button.
• Set the clock. The “Trunk Opening” button increases the values, the “Speaker” button decreases.
• To go to setting the minutes, briefly press “SET”.
• Set the number of minutes. The “Trunk” key raises the numbers, the “Siren” key lowers them.
• To exit, press “SET” for two seconds.

See everything about the Sheriff 5BTX925LCD keychain.

New cars > Car alarms >

This is interesting: How many times do you need to change the oil in an automatic transmission?

Functions

The KGB FH-3 alarm system has the following functionality:

• remote activation of alarm mode;
• engine blocking during forcible seizure of the car;
• silent activation of protective mode;
• activation of security functions when the engine is running;
• enabling protection using the service button;
• independent restoration of security in case of accidental deactivation;
• the ability to select the operating time of the interior lighting;
• self-diagnosis of the system, which starts when the alarm is turned on and off;
• silent security mode with sensitivity sensor bypass;
• remote activation and deactivation of the shock sensor using a step-by-step method;
• monitoring the operation of the central locking unit;
• determination of the state of the power unit, performed by analyzing signals received from the tachometer;
• gradual opening of door locks;
• opening locks using 2 pulses;
• “Comfort” mode (remote control of adjustable elements of the car);
• service mode used when transferring the machine for repair;
• requesting a password when the alarm is turned off;
• ability to manage additional channels;
• searching for a vehicle in the parking lot;
• possibility of returning to factory settings;
• determining the air temperature in the cabin;
• indication of battery charge in the communicator.

Advantages and disadvantages

The positive qualities of the KGB alarm system include the following characteristics:

• strength of the key fob body;
• extended set of functions at an affordable price;
• increased alarm volume;
• compatibility with any passenger cars;
• uninterrupted operation of the autostart system;
• ease of installation and configuration of the system.

Some users note the following disadvantages of the anti-theft system in question:

• insufficient protection of the car body;
• reduction in the range of the key fob during prolonged use;
• increased frequency of false positives.

How to attach a key fob to a KGB alarm system

Post by xitur » May 24, 2012, 10:16 am

Tyrik, What does the Starline hotline have to do with it. The KGB is a completely different company.

dethdron, Or get a new keychain from the KGB. Or B9 is suitable from Starline. If anything is available.

Messages: 728 Registered: Aug 25, 2007, 00:00 From: YaNAO Purpe Experience: 2006 Car: Nissan Teana : Awards: 1

Thanked: 6 times Thanked: 1 time

Post by Tyrik » May 24, 2012, 12:27 pm

Messages: 110 Registered: June 24, 2011, 00:00

Post by Yana_Levkovich » May 24, 2012, 12:57

Federal support service StarLine 8-800-333-80-30 Russia 8-10-8000-333-80-30 Belarus, Kazakhstan 0-800-502-308 Ukraine

Thanked: 33 times Thanked: 15 times

Post by Tramper007 » 24 May 2012, 14:27

Messages: 24 Registered: Jul 17, 2009, 00:00 From: Tmn Experience: 2006 Car: Kia : Awards: 1

Post by dethdron » May 24, 2012 3:59 pm

Hmm, I just compared the displays one to one in appearance,

I think it should work? Didn't anyone install it?

Added after 6 days 15 hours 52 minutes 56 seconds:

It’s decided, we re-wired the display from starline) Everything works fine) I did it on Ordzhonikidze 51. Thanks to Tramper007

Review of the KGB alarm keychain

To remotely control the kgb car alarm, key fobs are used. The requirements for transmitters are quite stringent.

The key fob must use battery power sparingly, correctly generate control commands, be maximally protected from interference, and correctly inform the car owner about the operating mode of the security system and the condition of the car.

Most KGB car alarms have a main keychain pager with two-way communication and an additional remote control.

Depending on the model of the security system, the transmitters differ, both in appearance and functionality. Some of them are completely or partially interchangeable, some are completely incompatible.

Functions

The KGB FH-3 alarm system has the following functionality:

Advantages and disadvantages

The positive qualities of the KGB alarm system include the following characteristics:

• strength of the key fob body;
• extended set of functions at an affordable price;
• increased alarm volume;
• compatibility with any passenger cars;
• uninterrupted operation of the autostart system;
• ease of installation and configuration of the system.

Some users note the following disadvantages of the anti-theft system in question:

• insufficient protection of the car body;
• reduction in the range of the key fob during prolonged use;
• increased frequency of false positives.

Description of the types of key fobs of the KGB security system and their costs

All KGB car alarm key fobs are divided into main and additional. The former, as a rule, have a display to inform the driver. Additional transmitters can be either unidirectional or feedback. Key fobs also differ in the number of keys and functions assigned to them. The design of the key fob body and the appearance of the pictograms differ depending on the security system model.

An example of a three-button multifunction key fob with feedback is the kgb fx 3 alarm transmitter. It operates at a standard frequency of 434 MHz. The battery is an AAA battery. The approximate cost of the transmitter is about 4000 rubles.

The kgb fx 5 keychain is interchangeable with the above model. It also has three buttons and feedback. The cost does not exceed 4000 rubles. Also, this keychain is partially compatible with kgb fx 7.

For ease of use, kgb ex 7 key fobs do not have a protruding antenna. The transmitter is also suitable for use with car alarms kgb ex 8. The cost of the device does not exceed 4,500 rubles.

Car alarm kgb tfx 3 has fully compatible key fobs with kgb tfx 5. The appearance of the transmitters is slightly different. The cost of the devices is about 3,300 rubles for a keychain pager and 1,500 rubles for a one-way remote control.

Unlike previous models, the main key fob of the kgb 5500 and kgb vs 5700 security systems has four keys. The transmitter is completely interchangeable for both car alarms, so linking it to both 5500 and 5700 will not be difficult. The cost of the device is 3,700 rubles.

Specifications

The KGB FX-3 car alarm system is characterized by the following technical parameters:

Equipment

The standard set of KGB FX-3 car alarms includes the following products and documents:

• instruction manual and warranty card;
• processor unit in a durable plastic case;
• main communicator with 3 keys and LCD display;
• two-level sensitivity sensor;
• emergency stop button;
• additional key fob with 4 buttons;
• transceiver module;
• limit switch designed for installation on the hood;
• 6-pin connector;
• LED indicator to determine alarm status;
• set of installation cables.

Replacing the batteries of the main keychain pager

The main pager fob usually uses an AAA alkaline or salt battery. Rechargeable nickel-metal hydride batteries can be used instead of a standard battery.

If the battery is low, you will see a special icon on the key fob screen. To change the battery, it is recommended to follow the following sequence:

• Remove the back cover.
• Lift the battery from the “plus” side and remove it.
• Install a new power supply. It is important to observe polarity, as incorrect connection may damage the transmitter microchip. The first side to insert the battery should be “minus”.
• Synchronize the key fob with the security system.

If the transmitter is unlinked from the car alarm, you need to link the device again.

Replacing the battery of an additional key fob

Additional key fobs use lithium batteries. The most commonly used power supply in optional kgb security system transmitters is CR2032. This allows you to make the device more compact. To replace the battery, follow the instructions below:

• Remove the cover.
• Use a screwdriver to pry up the battery. It is important to ensure that no short circuit occurs.
• Install a new battery.
• Check that the fixation is secure.
• Synchronize the key fob with the car alarm.