Autostart Tomahawk: how to enable, configure, disable Tomahawk alarm system

Some users actively turn on Tomahawk autostart, regardless of the alarm model. However, some motorists are not aware of the benefits of the security system, which significantly reduces the efficiency of the device.

The option of remote or automatic start is provided to buyers to be able to maintain the required engine temperature in cold conditions or warm up before driving. Depending on the Tomahawk model, the sequence of programming and monitoring modes may vary significantly. At the same time, there are also general points.

The following is an indicative manual for all modifications.

Find out how to enable autostart from the Tomahawk key fob.

Tomahawk alarm: autostart operating instructions

A complete guide to using the Tomahawk security system contains instructions on setting up and using autorun modes. Here there is information on how to use extensions to obtain the maximum effect and subtlety of adjustment of machines with manual and automatic transmissions.

For the convenience of the user, the entire process is accompanied by pictures and a description of the symbols. At the same time, the control panels and each fuse are described separately - this guarantees sufficient content and detail for independent installation and operation of the complex. The problem for 40% of users is that they receive the signal already installed, without instructions or technical documentation. To resolve such situations, on our website you can read online or download the official instructions for one of the models.

How to enable Tomahawk autostart

When asked how to install autostart on a Tomahawk alarm system, just refer to the manufacturer’s official instructions. Depending on the modification, several types of automatic start of the power unit may be indicated here:

by time (at regular intervals or at a set hour);
at a given temperature;
by timer;
forced from the remote control.

Before you begin active use of extensions, the device must be properly calibrated. Depending on the selected mode, the sequence of actions and programming methodology will differ.

Find out how to turn off the Tomahawk alarm on your car completely.

Tomahawk 9010: autostart programming table

It contains a complete description of the options configured using the service mode. Here is information about the sequence of actions and calibration of each option separately:

duration of operation of the power unit after turning off the ignition and rotation of the strater;
setting the temperature inside the car;
motor control signals;
activation of 2 additional modes;
howler pulse duration;
door control;
engine start delay;
duration of the central lock control pulse;
safe driving;
automatic activation of security;
setting up interior lighting;
setting for an hour warm-up;
turbo timer control.

There is also information on how to program an alarm for a car factory or remote engine start. You can learn more about enabling functions from the table itself.

How to set up auto start on a Tomahawk alarm system

This year you can still find comments online like “automatic start does not work or does not work fully.” These are consequences of incorrect calibration or connection of the device. The setup is done in programming mode, and the procedure is specified in the official instructions.

When performing manipulations, you can configure the following parameters:

start intervals;
engine start and stop temperature;
starter cranking time;
engine design;
gearbox type;
orientation to the tachometer, crankshaft speed or oil pressure during remote start;
motor operating time during a forced start operation.

Also, some models involve setting auxiliary parameters, their number depends on the selected device.

Possible faults

If autostart on the Tomahawk becomes impossible, you should consider possible malfunctions or take into account incorrect key fob settings. Sometimes the system simply malfunctions or does not respond to clicks at all.

The car stops starting, the ignition indicator does not light up, and the light signal from the headlights does not appear. Sometimes another problem occurs: the key fob is fully operational, but the engine does not autostart. There are also situations when, when the function starts, the ignition is turned on followed by a click, but without starting the power unit.

If autorun does not work, it may be due to the following problems:

Problems with the ignition wiring.
Start blocking with standard immobilizer.
No power supply from fuse.
Damage to the temperature sensor that provides automatic start.
Incorrect installation of the system or incorrect configuration of functions.
Problems in the control unit, when the tracks burn out during power surges.
The sensor jumps out of the housing. A similar problem occurs when installation rules are not followed. If parts are not securely fastened, they will become deformed with intensive use.

If you are planning to purchase an expensive alarm system, you need to make sure that you can set it up yourself. Otherwise, failures and malfunctions may occur during system operation.

How to disable auto start on Tomahawk alarm system

Typically, the remote start function of the power plant is used by motorists exclusively in the cold season, when a long period of idle time of the car can provoke critical freezing of the internal combustion engine, and as a result, difficulty leaving the parking lot. Thanks to the settings, you can start automatic heating of the engine and prevent this effect.

To turn off the start mode one-time, just enter a certain combination on the key fob, and to disable the function completely, go to the programming table. In the setup menu, control is performed using a service key hidden from prying eyes.

The sequence of actions and entry into the setup menu also depends on the specific model selected.

We also have instructions for operating the Tomahawk alarm key fob.

Emergency activation and deactivation of the alarm system

If the car does not respond to the key fob, you can use the emergency activation and alarm disabling function.

Emergency alarm activation

To activate an emergency alarm, you must:

turn on the ignition, but do not start the engine;
press the Override button eight times;
turn off the ignition.

The car will react with a single flash of the parking lights and a single sound of the siren. After 20 seconds, the system will automatically turn on the security mode.

If, 20 seconds after the emergency activation of the alarm, any of the security zones are triggered, the car will notify the user of this by flashing the parking lights four times and sounding the siren four times. After this, the user will have 20 seconds to disarm it. If this is not done, the system will activate the alarm mode.

Emergency alarm shutdown

To make an emergency shutdown of the alarm without a key fob, you must:

turn on the ignition (do not start the engine);
press the Override button four times;
turn off the ignition.

The parking lights will flash twice and the siren will sound twice.

REFERENCE. The key fob pager will continue to function even after the user has made an emergency activation or emergency shutdown of the alarm system

Responsible drivers independently determine how to provide their car with protection against theft, as well as eliminate problems with starting the engine during cold periods. Some of them install a Tomahawk alarm system with auto start on their car. It allows you to start and warm up the engine without leaving the building. But in order to avoid problems with the operation of a car alarm with an auto-warming function, it is important to fully understand how to use it.

Autostart Tomahawk: button combination

When programming and activating functions, it is important to know exactly which keys to press to correctly enter a command. An incorrect signal is not filtered by the head module and is perceived as a user desire. At the same time, errors in driving can significantly reduce the comfort and safety of vehicle operation. In most Tomahawk models, functions are activated like this.

Forced start - press the button on the key fob with a picture of a key.
Warming up by temperature - the key and the trunk lid symbol are clamped simultaneously.
Daily start at a given time - key + speaker.

It is also possible to activate these options using service buttons. Usually this is Override or Jack. These controls are mounted in an inaccessible place and are used exclusively in emergency situations.

Basic autostart malfunctions, causes and solutions

When autostart stops working after normal operation, you can do the following:

Change the batteries in the key fob, most likely this is the cause.
Then the communicator is disassembled and repaired if necessary. Damaged buttons are replaced, swollen capacitors are resoldered. If the remote control has been dropped into water, you need to remove the board from it and dry it in a warm and dry place.
The vehicle may be located in an area with significant radio interference.
Sometimes the security system malfunctions and you need to configure autostart again.
The remote control is faulty or the batteries in the key fob are low. First of all, you need to make sure that the batteries are working and replace them if they fail.
Damage to conductors or oxidation of contact elements on one of the car alarm structural devices. It is necessary to check all components of the anti-theft system, in particular their conductors. If the insulation on the cable has worn off, it must be replaced; oxidized contacts must be cleaned or resoldered. When replacing, use wires with the same cross-section. To prevent rapid wear of electrical circuits, it is recommended to additionally wrap them with electrical tape.
Temperature controller failure. With this problem, the engine will not be able to start based only on air temperature; in other cases, the start will be successful. It is necessary to check the sensor and its wires; if the cable is damaged, the electrical circuit is replaced with a new one. A possible reason may be drops of moisture getting on the connector, then drying the pad will resolve the problem.
If the above steps do not help, you should contact a specialist to reprogram the system.

If Tomahawk autostart does not work initially, the following reasons may exist:

In the X5 model, the settings for the key fob pager were made incorrectly. You can reconfigure them yourself.
An error was made during the installation process. Incorrect installation of the control unit or other structural elements of the anti-theft system. In addition to the microprocessor module, the temperature sensor and the autostart relay could have been installed incorrectly. If one of the components is incorrectly connected, autorun will not work at all or will begin to function incorrectly. It is necessary to diagnose the correct installation of all parts and reconnect them if necessary.
Conflict between the standard immobilizer and the anti-theft system blocker. To solve the problem, you will need to additionally install an immo bypass module.

How to start a car remotely

The ability to remotely start the engine allows the driver to save time on warming up the power plant after a long period of inactivity. It usually looks like this:

the user activates the mode while at home;
the car starts on its own and runs for the programmed time;
the driver goes down to the parking lot/garage and sees a car ready to leave.

All that remains is to open the doors and start driving.

At the same time, some car enthusiasts do not know how to start a car from a distance and what is required for this. You should first prepare the vehicle.

Turn off the ignition and remove the key from the lock cylinder.
Move the gearbox lever to the neutral position (for an automatic transmission it moves to the “P” position).
Apply the parking brake.
Get out of the car and lock the doors.

The preparation procedure is completed. If the sequence of actions is violated, the alarm will emit 4 chirps and a glare during the activation attempt.

Next, at the required time, press the key on the key fob with the image of a key. If the start attempt is successful, an icon with the car running will appear on the remote control display. If the command is rejected, “SP” will appear.

Remote engine shutdown with Tomahawk TW 9010

If the car starts automatically according to the preliminary settings. The user has the ability to disable the option from the remote control. This is usually necessary for unscheduled trips or when the motorist simply forgot to deactivate the extension in the spring.

The factory instructions for remotely disarming a car imply a simple sequence of actions.

Press the lock/key button on the key fob for 2-3 seconds.
The car will blink its side lights 4 times.
The keychain will make a specific trill.

If everything is done correctly, the car engine will stall and will not be reactivated.

Warm up every day

The Tomahawk autorun function is installed and configured by the user forcibly. To do this, you need to enter the programming menu, where you select the appropriate item. If there is a need for more frequent warm-up (in severe frosts, so that the engine does not have time to freeze), after activating the function, enter the corresponding combination on the key fob and select an interval of 1, 2, 4 or 12 hours.

Note! The presence of gaps and their duration may vary in different models.

Next, you need to figure out how to make the engine start on its own:

perform pre-launch preparations;
On the key fob, simultaneously hold down the key and the crossed out speaker.

If everything is done correctly, the dial will appear on the remote control display and a characteristic signal will sound – the command has been accepted. After which, the car will start on its own at the specified time every day.

Trigger by temperature

Using the Tomahawk alarm, the user can forcefully turn on the car engine remotely. The factory instructions contain comprehensive information on how to warm up the car at a given temperature. Typically, the mode is configured manually in the programming menu, where the thresholds at which the ignition is turned on and off are indicated - very convenient in harsh winters. Depending on the modification and the availability of the kit, the interior or engine temperature is set. The second option is more economically profitable. The engine compartment warms up faster than the interior, which helps save liters of expensive gasoline.

After initial programming and pre-launch preparation, the driver just needs to click on the key + button with the trunk lid open. After which, an icon showing a fan will appear on the display.

Tomahawk keychain. Main functions.

The printed instructions included with the purchased security system include a complete list of necessary information about the alarm capabilities and its installation. In any configuration, the Tomahawk alarm system comes with two key fobs: the main one and the auxiliary one.

On the front side of the main communicator body there are usually five keys and a mini-LCD display. Using this key fob you can control all functions of the security alarm. The display shows complete information about the current alarm status. Additionally, clock, timer and alarm options are installed here.

An additional keychain is included as a spare. It is used in emergency situations. This communicator does not have a mini display. Information is displayed on it using two light signals. When the system is operating normally, the light is green; when there is a malfunction, it is red.

How to set more warm-up on Tomahawk autostart

It is possible to increase the engine warm-up time on the Tomahawk alarm. To do this, you will need to use function programming in normal mode. Here the user enters a combination and increases the motor operation to the desired limit. You can also extend the activation of the ignition from the key fob. To do this, you will need to hold the key and the closed lock, which will increase the battery life of the power plant by 5 minutes.

Important! You can extend the warm-up time by no more than 20 minutes at a time.

Setting the clock, alarm and timer

To set the clock, alarm clock or timer, use button No. 3 (functions).

Setting the clock, alarm and timer

Modes	Number of presses on button No. 3 (functions)
Setting the minutes on the watch	1
Setting the alarm clock	2
Setting the minutes on the alarm clock	3
Turning the alarm on (off)	4
Setting the clock on the timer	5
Setting the minutes on the timer	6
Turning on (off) the timer	7

To set the time, hold down button No. 3 (functions) until the field with an electronic clock flashes on the pager screen.

To set the current clock value:

button No. 1 (trunk) increases the time, button No. 2 (quiet security) decreases it;
To quickly scroll through time, hold buttons No. 1 or No. 2 in the clamped position.

To set the current minutes:

briefly press button No. 3 (functions) and the cursor moves to the field with minutes;
button No. 1 (trunk) adds minutes, button No. 2 (quiet security) decreases them;
To quickly scroll through the minutes, hold buttons No. 1 or No. 2 in the clamped position.

If, after setting the minutes, you press the F button, the alarm setting mode is activated, but if you do nothing, the key fob will save the current time and exit the setting mode.

The alarm clock is set according to the same principle as the clock. If, after setting the alarm, you press the F button, the timer setting mode will turn on; if you do nothing for a few seconds, the current alarm value will be saved and the key fob will exit the setting mode.

To immediately begin setting the timer from standby mode, press buttons No. 2 (silent security) and No. 3 (functions).

Setting the timer in standby mode

Timer, min.	Number of clicks:
Timer, min.	On button No. 2 (silent security)	To button No. 3 (functions)
10	1	1
20	1	2
30	1	3
60	1	4
90	1	5

To go directly from the standby mode to setting the alarm clock, bypassing the clock setting mode, press buttons No. 1 (trunk) and No. 3 (functions). Then they proceed according to the standard pattern.

How to increase the starter operating time when autostarting Tomahawk

In some cases, when the internal combustion engine starts automatically, an error or failure of the on-board system occurs. This is often due to the fact that the starter cranking time is set too short and the engine simply does not have time to pick up the rotation. Tomahawk security systems have a standard ability to increase the interval. How to set the required time is indicated below.

Use the special key to enter programming mode.
Click on the Override button three times. In this case, the system will emit 3 chirps as confirmation of the command.
Press the required button on the key fob. The maximum time is 3000 milliseconds.

The sequence of actions for individual alarms may vary. How to prolong the operation of the starter on a specific device is written in the factory instructions of the unit.

Key fob programming

Up to four key fobs can be registered in the Tomahawk 9010 system. When programming new key fobs, the data on the old key fobs will be erased. Therefore, within each programming session, the user will have to register all valid key fobs.

To register a new key fob in the system, you must:

turn on the ignition, but do not start the engine;
press and hold the Override button;
after four siren sounds, release the Override button;
press and hold buttons No. 1 “Trunk” and No. 2 “Silent security” on the pager until one beep is heard;
repeat the last action with the remaining key fobs (after registering the first key fob, one beep will sound, after registering the second – two beeps, after the third – three, after the fourth – four).

New key fobs are registered. 6 seconds after registration is completed, the system will exit the programming mode.

ATTENTION! The interval between registration of key fobs should not exceed 6 s. Otherwise, the alarm will exit the programming mode.

Tomahawk auto start relay

The standard automatic start relay of the power plant is responsible for supplying power to the engine starter and spark plugs. The unit is highly reliable, but in some cases failures or unexpected breakdowns may occur. In case of critical damage, the auto start relay is replaced. Thanks to the simple design, you don’t have to look for an original part – there is a large selection of analogues on the market that fully match the parameters.

The relay itself is located inside the head unit and is connected to solder contacts. Only a qualified electrician knows how to connect it correctly. Consequently, the replacement of the part is carried out in a specialized service using appropriate equipment.

How much does a temperature sensor cost?

During operation of the alarm system, damage or failure of the antenna module may occur. The price of a standard sensor is determined by this block. Due to the fact that the sensor is located inside the block and is a single unit with the body panels.

The approximate spread of price tags in different cities of Russia differs. This is due to local characteristics and the complexity of delivery.

Where?	Price, r
Moscow	950
Saint Petersburg	1050
Rostov	950
Samara	920
Yaroslavl	900
Ekaterinburg	830
Chelyabinsk	980

The cost of the additional Tomahawk TV 9010 sensor is difficult to present in one table. The final price depends on the design and type of part.

Monitoring engine operation via generator

In most configurations of Tomahawk security systems, there is the ability to control the start of the start using the generator operation sensor. The principle of the method is based on the fact that when the power plant is started, a voltage drop occurs. When the internal combustion engine is fully started, the generator begins to generate electricity and the circuit indicators are equalized. At the same time, the automation is activated and the starter is de-energized.

The technique is one of the most reliable and simple to implement. The standard sensor cuts in parallel into the on-board circuit line and reads its condition.

How to leave a car with the engine running

The factory instructions have clear recommendations on how to properly program the Tomahawk alarm so that the car can be armed with the engine running. In most varieties, the sequence of actions is similar:

calibrate the option in the programming menu in advance;
get out of the car while the engine is running;
On the key fob, press the Zz button until you receive a siren chirp;
After that, click the specified element again.

If everything is done correctly, the alarm will automatically close the doors and activate the security mode. In this case, the motor will continue to run.

How to check the temperature in the cabin?

You can find out the state of the air inside the car without additional modifications or manipulations. The antenna module transmits basic information about the system, and can be activated by holding down the key with the open trunk lid icon. If everything is done correctly, the car will blink its side lights three times and the key fob display will reflect the current state of the system.

To obtain correct information about the temperature of the internal space of the machine, the factory recommends installing the transmitter in places inaccessible to direct sunlight or hot air flows from the climate control system/heater.

Alarm system with auto start Tomahawk: price

When asking how much a Tomahawk alarm with automatic engine start costs, you should pay attention to several varieties with this option on board. The table takes into account only the price of the complex itself, the cost of installation is not taken into account.

Model	In rubles
7,2	7500
9010	7000
7,1	7450
9030	7800

How the function works

Before purchasing a Tomahawk alarm with auto start, you need to understand how auto start works and what it is needed for. The operating principle of the system is quite simple: the driver sets operating parameters using an electronic board, to which sensors and ignition contacts are connected via a relay. The control unit is installed in a comfortable and freely accessible place, and then connected to the rest of the devices on the panel.

The device is controlled from a smartphone running iOS and Android or from a key fob. When the system checks the pressure, the starter engages after 2-3 seconds. In the case of diesel engines, a preliminary check of the storage plugs is carried out.

To warm up the Tomahawk and configure autostart, you can select one of two operating modes:

Manual control using key fob.
Autostart via a command from a mobile application.

The Tomahawk auto-start alarm system has the following parameters for configuration:

Motor operating time. This indicator varies from 5 to 20 minutes. In standard mode it is 10 minutes, but in winter it is better to increase it.
Temperature indicators at which the engine autostarts. They are measured by a unit installed in the cabin, and not by a sensor near the engine. In this case, the car owner independently adjusts the temperature in the range -5...+30°C. In normal mode - -10°C.
Cranking time of the crankshaft by the starter mechanism. The values vary and range from 0.8 to 3 seconds. The basic setting for the Tomahawk 90 timer model is set to 0.8 seconds. When the engine control option via tachometer readings is activated, the system automatically turns off the unit, so it is better to select an interval of 3 seconds. If the function malfunctions, each time you try to start, the parameter changes by 0.2 seconds.
Method of controlling the power unit. Modern Tomahawk alarms, which are controlled from a remote control, have the following control options - by voltage of the electrical network, by tachometer readings or by an indicator of fluid pressure in the engine.
Duration of operation of the second channel. This function must be changed when installing an immobilizer bypass. The valid range varies from 0.8 to 30 seconds. It is also possible to operate the channel during the entire autostart time.
Starting delay between activation of the ignition circuit and the starter mechanism. For engines operating on gasoline fuel, the indicator is 2 seconds, and for diesel units - 2-10.

Tomahawk without autostart, but with feedback

When asking about the alarm system, how to set it up so that it starts and warms up the engine, you should read whether the installation is capable of doing this. Existing types of security systems may not be equipped with such a function.

A complete list of capabilities of the selected element can be found in the factory instructions, and see the types of alarms on our website.

In fact, the lack of auto start greatly reduces the options and operating comfort of the vehicle. The driver has to manually warm up the car and put up with severe freezing of the internal combustion engine after a long period of inactivity in the cold.

Tomahawk autostart does not work

If the car alarm does not go off and is not set to warm up, there may be several reasons.

Pre-launch preparation was carried out incorrectly.
The operation of the main units is disrupted.
There is a strong voltage drop in the on-board network.
The batteries in the remote control are dead.
Software failure of the head module.

After eliminating any possible faults, everything should work.

Tomahawk starts and immediately stalls

There are questions on the Internet about how to start the engine if the car turns off and stalls immediately after starting. This is usually caused by severe freezing of the oil in winter or incorrect program settings. To fix the problem, just follow a number of tips:

reduce the start-up interval in winter;
establish control of operation using the tachometer or oil pressure;
check system calibrations.

In extreme cases, you will need to roll back the changes to factory settings and re-enter the tattoos.

Tomahawk blocked the engine when autostarting: how to remove

Some motorists ask questions online about the type, the alarm is blocking the engine from starting, what to do to fix the problem. There may be several reasons why the program does not turn the starter:

pre-launch preparation was carried out incorrectly;
the command was sent incorrectly;
there was a hacking attempt during the launch;
adjustment failure.

Having found out why the autostart does not start the car, you can independently diagnose and repair the device.

Tomahawk autostart failed

There may be a large number of reasons why automatic arming is not activated. The following are the main ones:

software glitch - firmware corruption can completely disable Tomahawk;
voltage drop in the on-board network;
mechanical failures or water ingress.

The hood sensor on the Tomahawk is triggered when the engine is running

Typically, when the alarm is sabotaged by an open hood, the display screen shows a car with an illuminated hood. If the compartment lid is completely closed, but the security system still displays an error, you will need to check the following points:

limit switch;
module wiring;
reception/transmitter antenna condition;
correct connection of the circuit;
the presence of system errors within the signaling system.

For everything to work properly, all you need to do is check all the components listed above.

Reset to factory settings

A factory reset can be performed using the built-in button. To do this proceed as follows:

turn on the ignition;
Press the Override button 10 times in a row;
turn off the ignition - the alarm sounds 10 trills;
press the Override button once – the alarm emits one trill;
press button “5” (lock);
turn on the ignition - the side lights flash 5 times.

When resetting the alarm to factory settings, all manipulations must be performed promptly and without delay.

Tomahawk alarm with auto start and feedback: reviews from owners

Motorists' opinions about the company's products.

Ivan:

I can't figure out how to set autorun. It stopped working a few days ago, I received the car with the parameters already configured, but now something has gone wrong. I don’t know, the connection diagram hasn’t changed, but nothing starts.

Paul:

Thank you for telling me whether the Tomahawk alarm can block the engine from starting. She didn’t want to work normally, now I understand the reason.

Fedor:

Why doesn't the car start with Tomahawk 9030 autostart. Help, I can't figure out how to disable the engine lock.

Basic principles of installing a signaling system

Before installing a car alarm yourself, you need to read the instructions. The location must be chosen so that the module is not easily detected by a potential burglar or hijacker. It is important to avoid sources of heat and moisture. The antenna should be placed at the maximum possible distance from the vehicle electronics and alarm units.

Step-by-step installation of an alarm system with Tomahawk auto start looks like this:

Turn off the onboard power.
The electronic control unit is placed in the cabin. The RF antenna must be high enough. Avoid contact with electrical wiring harnesses and metal objects.
We install the siren in the engine compartment with the horn facing down.
We protect high-current networks (dimensions, central locking, etc.) with fuse links.
We install the hood and trunk triggers in hard-to-reach places away from moisture.
The impact sensor should be located in the center of the vehicle.
It is advisable to solder the contacts in places where the ignition circuits are broken.

Car alarm connection diagram

Detailed connection diagram for the Tomahawk alarm system