Replacing dashboard bulbs on a VAZ 2114 – what bulbs are needed, how many pieces

Lamp functions

Dashboard-mounted lighting devices serve two purposes. Some of the light bulbs provide the actual illumination of the dials. This allows the person sitting behind the wheel to freely take readings from them, even when it is completely dark outside.

Other products are control. They are indicators that confirm the switching on of certain devices (headlights, headlights, etc.) or indicate problems. Making the panel more aesthetically pleasing is just an additional function.

Shnivy tidy does not work: reasons

Usually this is damage to the module's power circuit, moisture/condensation on the board, or mechanical damage caused by improper repair.

The problem is simple when studied in detail, and can be easily eliminated without the help of specialists.

The shield does not light up

If it just goes out (the backlight has failed), check the corresponding fuse inside the mounting block. Next you need to follow the wires towards the tidy. Here the condition of the contact groups and the presence of oxidation on the terminals are checked. If there are such problems, the problems should be eliminated.

If only some of the light bulbs stop lighting, dismantle the device and check the lighting elements directly for damage.

Shnivy's shield is blinking

A typical problem in cars that are driven on rough terrain or broken roads. A symptom of trouble is that the device periodically goes out while driving or blinks quickly.

Check the wiring and connecting terminals for possible damage or loose contacts.

Instrument needles Strings stuck

In such a situation, check the systems.

1. Fuse and power circuits of the interior lighting line. The design of the network is such that the power is crossed, which causes problems.
2. Mass disappears on the connected elements of the on-board circuits.

Which bulbs are suitable for the 2114th model

In general, the current legislation provides for quite serious sanctions against motorists who dare to make any changes to the design of the vehicle at their own discretion. In accordance with the rules, they are obliged to replace components and assemblies only with analogues of those chosen by the manufacturer. Failure to comply with this requirement provides grounds for punishment of the driver.

Fortunately, this standard applies to the dashboard purely formally. The owner only needs to ensure proper illumination intensity and proper operation of the display.

Thus, more and more owners are installing LED lamps on their 2114 Ladas instead of the standard halogen ones. This choice is easy to justify. In particular, they:

• consume approximately 8-9 times less electricity, which means the load on the on-board power system is reduced;
• last 5-10 times longer;
• give brighter light;
• practically do not heat up.

Finally, the dashboard looks much more attractive, because the light bulbs can be of different colors - blue, red, green, etc.

The problem is that LEDs cost about twice as much, but this disadvantage is more than compensated by their longer lifespan. In addition, LED lamps are becoming cheaper every year.

How to remove the tidy

To dismantle the panel you will need to follow a simple sequence of steps.

• Disconnect the battery and put the car on the handbrake.
• Next, you need to take a Phillips screwdriver and unscrew the two screws at the top.

• Next, you need to open the plugs on the dashboard and remove two more screws. They are located to the right of the hazard warning button and the warning lamp panel.

• After this, the board is pulled out towards itself, simultaneously with pressing in the latch
• Then two more screws under the cladding are unscrewed.

• At the end, the terminal blocks are disconnected and the part is completely removed from the machine.
• The car is assembled in reverse order.

Having figured out how to replace the backlight bulbs of the Shnivy tidy with your own hands, the user can significantly save money on contacting specialists. All actions are completed in 1-2 hours if the work is carried out slowly.

Specialization: Graduated from the State Automobile University, worked for 20 years at GAZ-56, now I drive a Zhiguli.

The instrument cluster includes many elements.

In accordance with the diagram above, the shield structure is as follows:

1. The coolant temperature control sensor, the arrow on it rises as the engine warms up. The controller needle should not be allowed to move into the red zone, as this will indicate overheating of the power unit.
2. A tachometer is a device that measures the number of revolutions of the engine crankshaft.
3. The left turn signal activation symbol, made in the form of a green arrow, appears when the corresponding indicator on the steering column switch is turned on. If the light blinks faster than usual, this may indicate a burnt out bulb.
4. Right turn signal.
5. Speedometer, this device allows the driver to know how fast the vehicle is moving. The speedometer is connected to the transfer case via an electric drive.
6. Gasoline fuel level controller; the Chevy Niva uses an electromagnetic device that functions only when the ignition is activated. When the ignition is turned off, the controller needle moves down the scale.
7. The fuel reserve indicator in the gas tank appears on the dashboard when the fuel level in the system is about 4-6.5 liters.
8. The side light activation lamp appears on the dashboard when the corresponding optics are turned on.
9. The brake system emergency symbol appears if the brake fluid level in the expansion tank has dropped to a critical level.
10. High beam indicator.
11. A key that allows you to reset the daily mileage readings. You can also use this button to switch to the clock or outside temperature sensor.
12. A screen that displays the total and daily mileage of the vehicle.
13. The Check Engine indicator indicates the need for engine diagnostics. It should always appear when the ignition is turned on, and disappear after starting the engine. If this light remains on while driving, the engine management system needs to be checked.
14. Light alarm activation lamp.
15. Symbol of time and temperature; you can switch from one mode to another using button 11.
16. Battery low indicator, this light should always appear when the ignition is turned on and disappear after the engine is started. If the indicator is always on, this indicates that there is no charging current in the on-board network. This may be due to a failure of the voltage regulator or generator unit, or the lamp may light up if the tension of the generator strap is insufficient or breaks.
17. Handbrake activation symbol. If your Niva Chevy is on the handbrake, the indicator will light up when you turn on the ignition and start the engine.
18. Indicator of emergency low pressure of engine fluid. It should always appear when the ignition is activated. If it lights up after turning on the engine, this indicates low pressure in the system or a lack of engine fluid.
19. Reserve indicator (video author - Artem S).

Why do light bulbs fail?

The main reason for the relatively rapid burnout is rather difficult operating conditions. Reduce resource:

• voltage fluctuations;
• vibration;
• overheating (in a closed space of the instrument panel this is normal).

In addition, filaments have a short service life of only 1500 hours.

In addition, lamps may stop working due to:

• wiring damage;
• destruction of board tracks;
• contact oxidation;
• blown fuses due to short circuit, etc.

For this reason, before replacing a light bulb in a Lada 2114, it is advisable to find out why it stopped working. Until the root cause is identified, the situation cannot be corrected.

One comment

Thanks for the info! Any driver knows how to track the condition of the car: using instrument readings. In the dark, illumination is responsible for their visibility. But all electrical devices have a limited lifespan, including incandescent light bulbs. They are used in the dashboard of the VAZ-2114. Replacing the light bulbs in it is not difficult, but painstaking.

Write a reply Cancel reply

This site uses Akismet to reduce spam.
Find out how your comment data is processed. Buy this site
Source

How many lamps does the VAZ-2114 dashboard contain?

Now we will tell you how many lighting elements are installed on the dashboard of the VAZ model in question. This will allow you to estimate upcoming expenses and immediately purchase the required volume.

So, the instrument lighting is provided by 7 lamps. In addition, there are other indicators:

• left and right turn signals – 2 pcs.;
• emergency oil pressure – 1;
• handbrake activation – 1;
• battery charge – 1;
• alarm - 1;
• malfunction of the motor control system - 1;
• high beam - 1;
• brake fluid level – 1;
• external lighting – 1;
• fuel reserve – 1.

In total, the VAZ-2114 has a total of 18 units. Experts recommend that even when one incandescent light bulb has burned out, immediately change everything. This ensures that the operation does not have to be performed again in the near future.

Identification of buttons

It is also important to know the designation of the buttons on the VAZ 2114 panel. On the instrument cluster on the right side there is a button (11), with which the time and temperature on the digital indicator are switched, and when pressed for 5 seconds or more, the current mileage is reset, if pressed this button on a stationary car.

In the central part of the dashboard are located in a row:

Buttons VAZ 2114

Double headlight switch. Button 1 turns on the dimensions, button 2 turns on the low beam;

Buttons on VAZ 2114

Key switch block. The first 1 turns on the front fog lights, the second 2 turns on the rear fog lights and the third 3 turns on the heated rear window.

Replacement - order

Having figured out how many lamps the dashboard contains, it won’t hurt to find out how to replace them on the 2114th model. The procedure itself is not very complicated, but extremely troublesome.

1. First of all, you will need to disassemble the shield. The radio tape recorder, heater and ventilation control levers are removed from it.
2. Then unscrew the screws holding the decorative panel trim. Before doing this, the steering wheel should be moved to the lowest possible position - this way it will not interfere.
3. Find the screws - there are five of them, and they are closed with plugs. Carefully pry the latter with a knife and pull it towards you. After removing the screws, pull the VAZ-2114 panel towards you.
4. Now you need to unscrew the two screws holding the instrument panel itself. This is done with a Phillips screwdriver.
5. Afterwards, the panel is lowered and the opened terminals of the wire loops are disconnected. Then the element is freely taken out.
6. Next, the damaged light bulb is pulled out - turn it 90 degrees in any direction until the protrusions on the socket fit into the grooves. Then all that remains is to remove the product from the base and put a new one in its place.

As noted above, so that the 2114 panel does not have to be disassembled again after some time, it is advisable to immediately replace all the lamps. This will also ensure an even glow of all elements.

Selection of light bulbs

Wiring ringing

Today the market offers a wide range of lamps that can be used for the dashboard of the VAZ 2114. Among the most well-proven devices, we note a few. Their name and cost are presented in the table.

Functionality check

After completing the replacement, install the panel inside the car, connect the connectors, but do not rush into final fixation - you still need to make sure that everything works properly.

To do this, turn on the ignition and see if the backlight turns on. Then check whether the indicator lights responsible for:

• hand brake;
• oil pressure;
• fault signal, etc.

Then test the turn signals, headlights and side lights. If everything is in order, then complete the panel assembly.

Replacing the backlight of the stove Lada 2123 (VAZ 2123)

You can try removing the dashboard. To do this, pull it towards you, but the panel fastening latch will get in the way. You need to press it slightly with your finger. Pull the shield towards you, moving it away from the instrument panel. We press the clamp of the shield fastening with your finger. Theoretically, the tidy is free, but it is held in place by wiring harnesses.

Carefully disconnect the contact blocks and remove the instrument panel assembly. Remove the instrument panel panel. When you flip the ashtray lid, you have simultaneous access to the ashtray and the cigarette lighter.

To use the cigarette lighter, press the socket button until it locks into place. After about 20 seconds, the cartridge clicks back to its original position, ready for use.

Design Features To clean the ashtray, press the cigarette extinguishing plate and remove the ashtray from its slot. When the exterior lighting is turned on, the inside of the ashtray and the cigarette lighter are illuminated with special lights.

Use a slotted screwdriver to pry up and remove two plugs. The first is located to the right of the hazard warning button, and the second is on the far right of the panel trim.

We turn out the screws located under the plugs. We pull out the right side of the dashboard trim and remove the connectors from the control buttons. Remember, take photos of which connectors go to which buttons!

We disengage the left side of the trim, remove the block from the buttons for turning on the headlights and dimensions. We remove and remove the lining.

Unscrew the two screws securing the dashboard. And, to be honest, reviews about it do not evoke positive emotions. First of all, this concerns the impossibility of repair.

Regardless of whether repair or replacement is needed, the shield will have to be removed. This is done using a Phillips screwdriver and a flathead screwdriver. Algorithm First of all, remove the negative terminal from the battery so as not to inadvertently short-circuit the electrical wiring.

Step-by-step instructions for replacing light bulbs in the dashboard of a VAZ-2114

1. We release the decorative cover of the front panel. For this we need screwdrivers: a short Phillips and a flathead one. Lower the steering column to the lower position using the height adjustment lever to keep it out of the way. The photo shows the mounting locations for the casing:
2. There are four screws on the bottom of the visor and above the steering column. Unscrew them with a short Phillips screwdriver.
3. Using a flathead screwdriver, pry off the decorative cap to the right of the row of switches. There is another fastening screw under it.
4. Also, remove the handles from the heater switch and damper control sliders by pulling them towards you.
5. If you have a car radio, you will also have to remove it.

   
   Unfortunately, complete dismantling is not possible. Arrows indicate locations for removal

6. Pull the front panel cover towards you. He must move. There is no need to remove it completely - there will be enough space to access the mounting screws on the sides of the instrument cluster.

   
   Carry out your actions carefully

7. Unscrew the fastening screws with a long screwdriver. The combination will be released and you can tilt it towards yourself. Pull out the two blocks with wires. Don’t be afraid to mix them up - there is a color marking, and the asymmetrical shape of the connector will prevent you from connecting it incorrectly.

   
   The arrow indicates the location of the cartridge handle

   Read also:  Types, design and principle of operation of fuel injectors
8. On the back cover of the instrument cluster there are cartridge handles. Arm yourself with small pliers. This will make it easier to unscrew them. To release the cartridge, half a turn counterclockwise is enough. You can safely take out all the cartridges - they are the same. Next, you can check the lamps with a tester and replace the burnt ones, or replace them all with LEDs at once. Try to ensure that they fit tightly in the cartridge, otherwise the contact will be unreliable.
9. We reassemble in reverse order. We insert the cartridges into the seats so that the antennae fall into the grooves, carefully turn them with pliers until they stop. We connect both blocks to the connectors of the instrument cluster.
10. Let's check if all the lamps are working:
11. raise the handbrake and turn on the ignition: so let’s check the handbrake, generator, oil pressure and check lamps,
12. turn on the hazard warning lights - check the warning lamp and direction indicator lamps,
13. pull the headlight switch lever towards you - temporarily turn on the high beams, check the warning lamp,
14. turn on the dimensions - see if the scales are evenly illuminated, and if the warning lamp, if any, is on.

If everything works correctly, we fix the instrument cluster and the front panel casing, and replace the heater switch handles and damper controls.

Check the brightness and functionality of all devices

Congratulations, now the instrument lighting and warning lights are working properly, and you will always be aware of what is happening with the car. The overall aesthetics of the front panel will also improve - the evenly lit front panel looks beautiful.

The instrument panel on the VAZ-2114 is specially designed for the driver to control all data emanating from the engine, monitoring the fuel level, and other data.

Video with replacing light bulbs on the dashboard of a VAZ-2114:

The instrument panel should always be kept in good working order, because a non-working backlight can cause not only discomfort when moving in a car, but can also cause a simple error due to missing a problem with the warning lamp.

Therefore, as soon as you discover a non-working lamp on the instrument panel of the VAZ-2114, it should be changed immediately, and how to do this is described in detail below in our article.

Procedure for installing new light bulbs

1. If there are faults in a particular lamp, the first step is to unscrew the non-working socket where it was located.
2. Unscrew it counterclockwise, being careful.

We carefully remove the socket with the light bulb.

The LED light bulb is ready for installation.

Please note that the shape of LED lamps is square, and since it differs from ordinary light bulbs, the excess simply needs to be sanded off.

1. After all the new lamps are installed in place, we check their functionality by connecting the wire block to the instrument panel without first fixing it.
2. When everything is checked and working, you can reassemble everything in reverse order, remembering to tighten each bolt securely.

Diode lamps shine brighter and better.

Reasons for failure of dashboard lights

Old burnt out dashboard light bulb in socket

There may be several reasons why the instrument panel lamps are out of order:

• The incandescent lamps burned out, or in the case of LED analogues, the tracks stopped working.
• A malfunction has occurred in the circuit of electrical appliances (a break has occurred or the contacts have oxidized - approx.).
• The fuse box has failed.
• Damage has occurred on the instrument panel contact board.
• There is a short circuit to ground.

In order to understand this problem more closely, it is necessary to dismantle the instrument panel.

Brief summary of the work done

As you can see, this work is not labor-intensive and does not require large financial investments or effort. Therefore, you should not rush to contact a car service center, where you will most likely be offered to replace the entire dashboard , which will cost several hundred rubles, not one thousand. Now you know what to do if suddenly the light bulbs on the panel fail. We wish you good luck and a safe journey!

Bright backlight

But quite often, VAZ 2114 owners discover that the instrument panel lights do not light up. If such a situation occurs, appropriate action should be taken immediately to eliminate it.

Replacing light bulbs with LEDs in the instrument panel

I decided to change the light bulbs in the instrument panel due to the fact that they began to burn out, since an alarm was connected to the dimensions. I decided to buy LED bulbs so I don’t have to climb anymore.

light bulb with socket

In the store I decided to buy regular white ones; there were red and green ones to choose from. I also bought bases for them, since in my device, and it is from AP. The bulbs are soldered to the bases. If you need to change all the light bulbs, you need 12 pieces, if only for the backlight, then 7... I decided not to save money and change everything.

Disassembly began by removing the side panels. 3 screws on the left

left panel

and 5 screws on the right

right panel

Then you unscrew the fastening of the front panel to the rigidity using a self-tapping screw on each side.

left

on right

Then remove the heater control lever handles. prying the upper arms from above with a screwdriver

levers

and the bottom one is below.

Then remove it by pulling it towards you and prying the fan switch lever with a screwdriver.

fan lever

Then we take out the ashtray so it doesn’t rattle and stick out the radio, my wires turned out to be long, I didn’t have to disconnect anything except the antenna.

radio tape recorder

After this, remove the plug in the upper left part of the front panel and unscrew the screw

top panel

And now all that remains is to unscrew the 4 screws in the mount in front of the instrument panel. 2 on top are bigger

up

and 2 smallest ones below right and left of the steering wheel

to the left of the steering wheel

After this, the panel is completely unscrewed, we slightly pull it towards ourselves and turn it to the right, freeing the instrument panel.

front panel

Next, unscrew the instrument panel itself. it is secured with two screws.

on right

left

Having unscrewed it, we freely pull out the panel and can begin replacing the light bulbs. It is better to do this with pliers.

panel

The backlight lamps are marked in red, and the signal lamps are marked in blue.

rear instrument panel

Reassemble in reverse order. During this work, no difficulties arose; everything fell into place. The result was a good result... The backlight turned pale blue.

finish

Let's get started

First of all, we remove the decorative trim of the radio (since the dashboard and radio are connected to each other, you will have to disturb the music system too), which is held on by fasteners; here it is better to use a screwdriver, threading it under the trim.

The main condition of work is caution. You need to start detaching the cover from the bottom edge. When the bottom edge comes off, you need to pull it towards you a little. Now detach the top edge. Further:

1. Disconnect the wire directed to the cigarette lighter.
2. In the same way as we removed the cover from the radio, we remove it from the dashboard . Above the left and right edges we find two self-tapping screws. They need to be unscrewed. We unscrew the screws located at the top and bottom.
3. We remove the trim with a little effort (since it is also held on by fasteners, so the decorative plate will have to be rocked a little).
4. We disconnect all the wires: from the alarm system, from the clock, from the headlights and other things.
5. panel itself , for which we unscrew the four screws on which it is held. In order not to damage the wires, it would be better to disconnect them on the one hand.
6. Now the most important thing. We remove the sockets of the light bulbs that have stopped burning. To remove the cartridges, you need to turn them counterclockwise with a gentle movement. We replace the defective lamps with new ones, wrap them and install the entire structure in the reverse order of disassembly.

Reasons for failure of dashboard lights

The dashboard lighting performs several important functions in parallel:

• control. The lamps light up when failures or malfunctions of individual components occur;
• informational. Notifies the driver in real time about the status of important vehicle systems;
• decorative In a dark interior, beautiful lighting on the instrument panel decorates and enlivens the front part of the cabin.

The main reason for the failure of light bulbs in the instrument panel is difficult operating conditions - heating, vibration, power surges. This significantly reduces the life of the lamps and causes a lot of problems:

• burnout of filaments in halogen devices, burnout of current-carrying paths in LED lamps;
• broken wires or the appearance of an oxide film on the contacts;
• problems with the fuse box or contact board;
• somewhere shorted to ground.

Before you try to change the lamps, you should accurately determine the cause of the problems that have arisen, otherwise you will not be able to get the expected result. It is important to know the condition of the fuses and the condition of the wires. The insulation on them often frays and begins to short to ground. It is necessary to inspect the wiring and replace problematic connections. In addition, you need to clean the contacts. The terminals oxidize and the ability to conduct current decreases. This applies not only to Ladas; such danger is a common “disease” of most cars.

Why lamps burn out or stop working: causes and consequences

The backlight operating conditions are not ideal: shaking, temperature changes, possible power surges in the on-board network, and so on. When driving, you must turn on low beam headlights. Along with it, the instrument lighting also turns on. This can shorten the life of the lamps, and over time, not the entire panel is illuminated evenly.

The main danger of lamps burning out in the instrument cluster is that some of them are control lamps. In this case, you may not know about the failure of individual machine components. And uneven illumination looks ugly.

How to choose lamps

According to current rules, tampering with a car's structure is punishable by a fine or even deprivation of a license. Therefore, only an equivalent replacement with the same lamps used by the manufacturer is considered acceptable. However, the attitude of traffic police officers towards the dashboard lighting is more loyal. This is explained by the absence of danger for drivers of oncoming cars.

Most car owners use LED analogues instead of conventional incandescent lamps. This choice is explained by the significant advantages of LED devices compared to traditional lamps:

• long service life;
• low power consumption that does not drain the battery;
• no heating that negatively affects plastic parts.

Attention! The only drawback can be considered the relatively high price, but since the appearance of LED lamps on the shelves, there has been a noticeable decrease in their cost. In addition, the range of LED lamps is wide and allows you to choose inexpensive units.

Be sure to check out:

The best lamps for Opel Astra h: manufacturers, markings, table of those used The best lamps for headlights VAZ 2114 High beam lamps Lada Priora: the best models and step-by-step replacement instructions Low beam lamps Chevrolet Lacetti: the best manufacturers, replacement and adjustment process
All lamps are selected according to the following parameters :

• cartridge type - 2W2;
• supply voltage - 12 V;
• power - 12 W.

Sometimes you have to change all the lamps. When purchasing, you need to know how many light bulbs are in the dashboard of a VAZ 2114.

For a complete replacement you will need to purchase:

Usually LEDs are initially installed in the BSK, since it comes as a separate unit. When purchasing replacement lamps, it is not necessary to purchase sockets; they remain operational for a longer period than the lamps themselves. A total of 8 light bulbs need to be replaced. They are the same; when purchasing, you should be guided by the type of cartridge, supply voltage and power.

Solution

The stores offer several options for light sources for replacing lamps in the instrument cluster:

• traditional incandescent lamps,
• LED in a plastic socket,
• SMD LED is a more expensive and reliable option, a super-bright diode.

The choice will always depend on financial capabilities and lighting preferences

The number of backlight and control lamps is up to 19 pieces. It varies slightly depending on the design of the instrument cluster and the modification of the vehicle. Many car owners choose LEDs due to lower energy consumption and longer service life. This backlight is brighter and gives an interesting bluish color instead of the standard green. But due to the design of the diode, the brightness control of the instrument illumination will not work, always turning it on at full power. On a long road trip at night, this can be distracting and irritating to the eyes. But in any case, the choice of light sources is yours.

Replacement instructions

The procedure for replacing dashboard lamps is not particularly difficult. The only problem may be disassembly, which allows you to remove the backlight panel and get to the light bulbs. The difficulty is that the fastening screws are located at different points, and you need to know their location. Let's consider the process in order:

Required Tools

To replace the light bulbs in the dashboard you will need:

• a screwdriver with a cross blade;
• a flat-head screwdriver, preferably with a thin blade for unsnapping plugs and fasteners;
• pliers for dismantling cartridges;
• set of replacement lamps.

A small number of necessary tools makes the work convenient and fast. If you plan to make a small tuning - changing the color or brightness of the backlight, then additional devices will be required to remove the factory paint, dismantle the plastic filters and a solvent to clean the remaining paint layer on the back of the instrument panel.

Replacing the backlight

To obtain an even backlight, it is recommended, if possible, to change all the dashboard bulbs at once. Replacing one lamp can create a situation where after a week you will have to repeat the entire procedure in order to change another burnt out lamp. Therefore, experts recommend updating all the lighting at once. It is also advisable to replace incandescent lamps with LEDs - they are economical, have a wide range and provide a large selection of shade and brightness.

How to disassemble the dashboard

First of all, you need to remove the decorative trim from the radio. On the VAZ 2114, the dashboard is mechanically connected to this part, so you need to immediately disconnect it. After this, perform the following steps:

• Using a flathead and Phillips screwdriver, the decorative casing is disconnected. The steering column should be lowered as much as possible so that it does not interfere with the work. You will have to carefully snap off the decorative plugs and unscrew the 5 screws securing the casing. You also need to remove the handles from the sliders and the heater switch;
• After disconnecting the screws, the casing must be pulled towards you. You should act carefully; perhaps not all elements have been removed yet and they can be broken. You don’t have to completely remove the casing; there’s enough room to unscrew the mounting screws;
• To disconnect the dashboard you need a long Phillips screwdriver. Unscrew the screws, tilt the shield towards you and pull out the terminal blocks with connecting wires.

Important! After this, the panel will be completely freed and you can work with it freely.

Replacing backlight bulbs

To dismantle the cartridges, it is convenient to use small pliers. They grip the flat back. It is carefully turned half a turn counterclockwise, after which the assembly can be removed from the socket. In a similar way, all elements to be replaced are extracted. Then the lamps are removed and new copies are installed in their place. Insert the cartridges into the sockets and turn them half a turn clockwise to secure them. After this, it is recommended to connect the terminal blocks, apply operating voltage and check the functionality of the light bulbs until the casing is assembled.

The vehicle systems are checked:

• turn on the ignition and check the operation of the oil pressure, generator and check indicators. Raise the handbrake lever and see if the lamp lights up;
• trigger an alarm to check;
• switch the high and low beam of the headlights and determine whether the indication works;
• include dimensions.

If all elements of the lighting system are operating normally, reassemble the dashboard in the reverse order. This completes the process of replacing the VAZ 2114 dashboard bulbs.

How to replace light bulbs

Installing new lamps is a simple process that novice car owners can do.

To replace you will need the following devices:

• Phillips screwdriver;
• a set of new light bulbs.

Replacing the backlight

To improve the quality of dashboard lighting, it is advisable to replace old lamps with new LEDs - they provide brighter and softer light that does not irritate the eyes, have minimal power consumption and allow you to more accurately read data from devices.

Before you begin installing the lighting fixtures, you need to remove the decorative trim from the music system - the instrument panel and radio on the VAZ 2114 are connected to each other, so this step cannot be avoided. Dismantling is carried out by snapping off the fasteners with a flat screwdriver

Remove the cover from the bottom edge and be very careful, as all the latches can be damaged.

How to disassemble the dashboard

Dismantling the VAZ 2114 dashboard is the first step in the process of replacing backlight bulbs. Without removing the plastic cover it is impossible to get to the lighting fixtures themselves.

Scheme for disassembling the VAZ 2114 dashboard

The dashboard on the VAZ 2114 is disassembled according to the following scheme:

1. Three self-tapping screws are unscrewed, the lower protrusion and the cover are removed.
2. There are five screws on the right console trim that also need to be removed.
3. The screen is removed and the negative terminal is disconnected from the battery.
4. The wiring harness is disconnected from the cigarette lighter.
5. The handle is removed from the gear shift lever.
6. The stove fasteners are removed.
7. The bolts that secure the steering wheel block are carefully unscrewed.
8. Decorative inserts, lamp sockets and LEDs are removed from the panel.
9. The hydraulic corrector illumination lamp is removed using a 21 key.
10. The upper and lower screws are dismantled.

After completing the dismantling of the instrument panel, the wiring circuit is closed to prevent dust, moisture or dirt from entering it.

Only 8 out of 13 lamps can be replaced in the instrument panel of a VAZ 2114.

Before installing new lamps, remove the plastic cover from the instrument panel

Replacing backlight bulbs

After removing the plastic, you can begin the process of replacing the lamps.

1. The required number of lamps to replace the backlight of each sensor and panel device is calculated in advance.
2. Lamps and resistances are installed in special places - sockets - after removing the block. The cartridges are unscrewed counterclockwise by hand, without the use of tools. New ones are installed in the vacant spaces, then lamps are inserted into them. The LED heads are screwed in with correct polarity.

   Placing new lamps on the instrument panel

3. The power is connected and the functionality of the updated backlight is checked.

   Checking backlights with a multimeter

4. The instrument panel is being reassembled. The wiring is neatly routed to the board and attached to it, so that the parts will not interfere during assembly.

   The instrument panel is being reassembled with the sensor arrows placed

5. All arrows of sensors and instruments must be positioned correctly. If you rush too quickly during installation, you may break or bend them.
6. The entire structure is attached with screws.
7. The power supply of the LEDs and light bulbs is combined, the arrows are placed in their places and set to zero.
8. The operation of the panel instruments and sensors must be checked by the on-board computer. If everything is functioning properly, the dashboard is reassembled and returned to its original state.

   Assembled and tested instrument panel of VAZ 2114

Video: replacing the dashboard light bulbs of a VAZ 2114

Replacing the dashboard backlight bulbs of a VAZ 2114 is an easy job that can be done by the most inexperienced car owners. You can restore its functionality in a matter of minutes, the main thing is to correctly select and install sensor and instrument lamps.

Main conclusions

The process of replacing the backlight takes some time. The whole difficulty of the procedure lies in dismantling the front panel. The following conditions must be met:

• free the casing from handles, sliders and other elements;
• remove the handle from the gear shift lever;
• push the panel towards you, unscrew the shield and disconnect the terminal blocks from it.

The remaining operations are simple, performed quickly and without surprises. It is impossible to make a mistake during reassembly; the blocks with wires are made different and cannot be mixed up. Express your thoughts about replacing light bulbs in the VAZ 2114 dashboard in the comments.

Sources

• svetilnik.info/avtomobilnyj-svet/zamena-lampochek-v-pribornoj-paneli-vaz-2114.html
• drive2.ru/l/3636448/
• kalina-2.ru/remont-vaz/skolko-lampochek-v-pribornoj-paneli-vaz-2114
• ladaprofi.ru/vaz-2114/skolko-vsego-lampochek-v-pribornoj-paneli-vaz-2114.html