Characteristics and instructions for connecting and operating various alarm systems with auto start from Panther

Author: Victor

All Panther alarms with auto start provide the ability to automatically start the engine according to the timer, temperature sensor and command from the remote control. Anti-theft systems have a two-way communication function and a dynamic code that protects signal transmission from interception, intelligent hacking and scanning. In addition, Pantera car alarms can be configured with several protection options - standard, quiet, silent and with the engine running.

[Hide]

Specifications

Description of the main parameters of the Panther car security system:

• codes are transmitted via two-way feedback via a special channel with an operating frequency of 433.92 MHz;
• the maximum operating range of the communicator (pager, key fob, remote control) in the anti-theft complex control mode is 600-1000 meters;
• the operating range of the transceiver when the warning system is turned on will increase to 1.2-2 km;
• the alarm current consumption when the protection mode is activated is no more than 25 mA;
• The security system is powered from a 12-volt power source (short-term voltage surges up or down by 4 V are allowed);
• The Panther alarm system can simultaneously work with no more than four key fobs;
• There are mainly six security zones used to protect the vehicle;
• The degree of protection according to GOST of the siren corresponds to the IP54 standard, and all other car alarm elements correspond to IP40;
• the temperature range to ensure uninterrupted operation of the system is from -40 to +85 degrees%;
• In terms of climatic design, Panther alarm models comply with the U-2.1 standard.

The range of key fobs depends on several factors:

• relative position of the transceiver and transceiver;
• terrain;
• number of dense buildings and architecture;
• weather;
• correct installation of all alarm components;
• battery charge in the key fob.

It is important to know

The actual operating range of the Panther alarm remote control is no more than 200 meters.

Additional characteristics of system advantages

Alarm Scher Khan Magicar

First of all, it is worth noting that the Panther alarm system meets a high level of protection. The developers have reached a completely new level in protecting the signal from electronic hacking and interception, and its noise immunity. The implementation of these characteristics was made possible through the introduction of dual dialogue technology and the use of narrowband FM control and feedback channels. This technology also facilitates seamless alarm management in shopping mall parking lots.

Increased protection against theft of a system with autostart includes:

• Enable active and safe engine shutdown in Anti-HiJack mode automatically or from the key fob.
• Built-in power relay, which is responsible for blocking the engine start.
• When the security system is activated, the faulty zone is bypassed, which is instantly displayed on the key fob display.

A wide range of capabilities of the autostart system offers:

• Automatic heating of the car, switched off remotely, at temperatures of -5C˚, -15C˚, -20C˚, -25C˚, which ensures an increase in engine and battery life.
• For diesel engines, the operating time of glow plugs is 2/10 sec.

Panther alarm keychain

Two-way control of the system is carried out using a key fob with a liquid crystal display. The temperature range of use is quite wide. Some Panther modifications are offered with automatic engine start. With a detailed acquaintance with this manufacturer, product representatives will introduce a huge number of other advantages. The advantages listed above distinguish the new product with auto start from all alarms presented on today's security systems market.

Equipment

Delivery kit for alarm system with auto start Panther:

1. A control device equipped with a microprocessor. Supplied to the market in a black plastic case with brand markings.
2. Main pager for control, equipped with five buttons and a display. The presence of a screen makes it possible to use remote communication with the car.
3. Additional key fob without display. This device has four controls.
4. A transceiver module equipped with an antenna adapter and a button to call the car owner from the passenger compartment. The device is equipped with a built-in temperature sensor.
5. Impact regulator designed to fix any physical impacts on the vehicle body. The device belongs to the class of two-level sensors and is equipped with a cable for connecting to the mains.
6. Siren.
7. LED light to determine alarm status. Equipped with a wire for connection.
8. Button to activate the service maintenance mode. Also comes with a cable for connection.
9. Push-button limit switch with connecting terminal.
10. A set of wires with connectors for installation.
11. Service user manual that allows you to correctly install, connect and operate the security system. The manual includes an electrical diagram for installing the alarm.
12. Two sets of power supplies for installation in the main and additional consoles.
13. Stickers on car glass for fixing the transceiver.
14. Consumer Memo.
15. Warranty card.
16. Packing box.

Good to know

Since the Panther alarm system does not include limit switches for doors and trunk, these devices must be purchased separately.

Photo gallery: Panther alarm elements

The photo shows the complete set of alarm delivery kits

One-way remote controls

Main keychain

Recommendations for correcting malfunctions

Reviews from motorists who use this car security system are generally positive. But she also has her weak points.

Some drivers are interested in the question of what to do if the key fob light is constantly on when the batteries are new. This may indicate a malfunction of individual parts of the unit, incorrect connection of the trunk, or the key fob needs to be reprogrammed.

If some alarm elements malfunction, it is better to contact specialists or replace it completely. To reconnect the trunk, you need to carefully read the instructions again and study the diagram to connect it to the system correctly.

But if reprogramming the key fob is required, then you need to be especially careful. To correctly link the block and keychain, you need to perform the manipulations specified in the instructions. For the model with index 1000, the instructions contain detailed steps on how to do this.

If the instructions do not contain such recommendations (outdated one-sided models), then it is better to turn to specialists.

Also, many car enthusiasts are interested in the question of how to turn off the alarm if it goes off. The easiest way is to press the button on the key fob. If the light continues to light, it means that unauthorized entry into the car has occurred, and here the algorithm of actions is different.

In this case, the alarm must be turned off using a special button, which is installed in a secret place, but accessible to the driver. If the alarm requires entering a PIN code, then you need to do this, if not, then you simply press a button and the system turns off.

Panther car alarms produced by a Russian company are created on the basis of the latest technologies, are well adapted to the conditions of the CIS countries, and are reliable systems, therefore they are recommended by many car enthusiasts.

Key Features

List of main features and capabilities of Panther alarms:

1. Transmits data, alarms and alerts to a screen-based communicator.
2. Availability of “Panic” mode. It allows you to remotely activate the siren and external lights to scare away intruders from your car. Using this function allows you to designate a machine as protected.
3. Blocking the car's power unit and preserving it when the alarm is removed or turned off.
4. Possibility of adjusting shock sensor parameters remotely, by level. The user can disable warning or alarm zones individually or immediately. To adjust the sensitivity parameter, use the communicator.
5. Availability of additional channels for controlling auxiliary devices and equipment.
6. Ability to control interior lighting fixtures installed in the vehicle interior.
7. Indication of time and temperature on the communicator screen. The key fob display also displays information about the battery charge. Thanks to the remote control indicators, you can promptly determine the discharge of the power source.
8. Possibility of remote engine start at a certain time. The user independently adjusts the cranking time of the starter device when starting, as well as engine operation. Remote extension of time for motor operation is allowed.

Removing the alarm according to the instructions

Documented descriptions of user actions allow you to familiarize yourself with the sequence of steps that must be applied to disable the alarm signal or the entire protection system. Several shutdown options are possible

:

• dynamic alarm muting
• disabling security functions
• silent removal of security functions
• disabling immobilizer mode

How electronic door locks, if installed in the system, function is also described in detail in the Pantera alarm instructions. Provides information about the purpose and operation of the Valet function

. The actions aimed at disabling the system using a personal code are explained.

Alarm models with auto start

All systems with automatic engine start can be divided into two classes - commercially available alarm systems and discontinued models.

On sale

List of models that can be found on sale:

• SPX-2RS;
• PR-2;
• SLK-775RS;
• SLK-868RS.

SPX-2RS

Features of the SPX-2RS alarm:

• 7 independent security zones;
• it is possible to bypass a faulty zone when arming by indicating a zone or trigger;
• there is a passive engine blocking mode / immobilizer;
• has dual dialogue signal coding, as well as the SmartStart intelligent control system;
• 8192 communication channels are used to protect impulses of the security complex;
• equipped with a GPS/GSM unit, which provides the ability to control the system anywhere in the world;
• characterized by the highest possible performance - the response time is 0.25 s.

Alarm SPX-2RS

PR-2

Model PR-2 is characterized as follows:

• equipped with the SmartStart intelligent control system;
• The presence of a GSM module in the kit allows you to control the alarm using cellular communication channels;
• Pulse data is protected through the use of dual dialogue encryption technology;
• the alarm is available to control functions within a radius of 600 meters, and its signal is audible at a record 1200 meters;
• disabling the security mode is carried out in two stages.

One of the features of the alarm is the presence of a Saturn SCB-1230D digital programmable relay and a standard Saturn AU-50 immobilizer crawler. The relay provides an additional level of anti-theft protection in the event of a shutdown of the main system unit. Saturn AU-50 allows you to implement autostart on cars with a standard immobilizer.

Main unit and communicator model PR-2

SLK-775RS

System 775RS:

• allows you to remotely start a car engine at a specified time, according to a timer, or when the temperature drops to a certain threshold;
• in alert mode, the range of the communicator, according to official data, is 1500 meters, when sending signals - up to 800 m;
• implemented remote monitoring of the necessary indicators (engine temperature, cabin temperature, on-board voltage, engine speed);
• there is an automatic closing of the doors upon the “brake” signal;
• there is an additional output for remote control of the trunk actuator/other device;
• equipped with a protection system against external interference.

Primary and additional communicator model Panther SLK-775RS

SLK-868RS

Model 868RS has the following features:

• allows you to control the operation of the security complex from anywhere in the world using a mobile phone;
• the control unit is equipped with two additional outputs for connecting the power unit lock;
• data transmission is carried out via a radio channel with a frequency of 868 MHz;
• in control mode, the range of the communicator should be 700-1000 m, when receiving alerts - up to 2 km;
• protection is provided in the “warm-up” mode (with the engine running at idle speed);
• There are functions “Car Search”, “Owner Call” and “Comfort”.

Equipment Panther SLK-868RS

Out of production

Models of Panther systems discontinued:

• SLK-650RS;
• SLK-675RS;
• SLK-625RS;
• LX-320.

SLK-650RS

Main characteristics:

• car alarm with feedback, remote start and 7 independent security zones;
• presence of an advanced Anti-HiJack mode (AVR™);
• 6-tone siren;
• 1- or 2-digit system shutdown PIN code, programmable;
• modernized dynamic code with protection against scanning and interception;
• possibility of connecting up to 2 additional engine blockers;
• the presence of a function for separate control of right/left turn indicators using a built-in relay;
• possibility of arming without the help of a key fob transmitter;
• option to arm the system with separate disabling of sensor zones;
• Valet mode with remote control capability and warning about activated mode.

Alarm equipment Panther SLK-650RS

SLK-675RS

Model Description:

• This version implements two-way communication using Bilarm technology and dynamic pulse encoding;
• there is a self-diagnosis function;
• disabling the security mode is carried out in two stages;
• the model provides 7 security sections independent from each other;
• operating radius of the main/additional key fobs - control 1000-450 m, notification 2000 m-700 m;
• presence of the IntelliStart function;
• the presence of a programmable turbo timer mode;
• remote monitoring of the vehicle’s condition (measurement of t in the cabin, voltmeter and tachometer readings with the engine running);
• automatic door opening/closing mode - by brake and ignition;

Alarm Panther SLK-675RS

SLK-625RS

Features of this model

• an alarm system with auto engine start and two-way communication allows you to timely determine the discharge of the battery in the car;
• equipped with the option of self-diagnosis and bypass of non-working areas;
• has 7 independent security areas;
• an additional channel is provided for controlling the trunk actuator or other device;
• has all the standard functionality necessary for full use;
• it is possible to control the central locking by turning the ignition system on and off;
• When operating in open areas, the range of the 625RS communicator should be up to 2 km.

Alarm Panther SLK-625RS

Video: Panther 625 alarm operation

The AvtoGSM channel in its video demonstrated the operation of the Pantera 625 anti-theft system.

LX-320

Features of this version:

1. Even though this model is older, it supports the ability to control a mobile device. If, when the security system is turned on, the system detects a problem area, it will “bypass” it and warn the consumer about it.
2. The system provides the ability to connect up to two car engine locks.
3. The range in control mode is up to 600 m, and in alert mode up to 1200 m.
4. The package includes a 6-tone siren.
5. Silent activation and deactivation of the security mode.
6. 4 additional channels for controlling vehicle devices.
7. 6 induced security zones.

Main alarm communicator Panther model LX-320

Models and prices

Features of the latest versions of anti-theft systems:

1. SLK 625rs. This model of the security system has a feedback feature and an option for automatic engine start. The system remote control is equipped with a screen, which makes it easier to control the alarm. The display shows the battery charge. Using a pager, the car owner can turn the system on and off, and enter service mode. You can also remotely start the engine in accordance with temperature indicators or time, and search for a car in the parking lot. The engine start function can be implemented remotely on both gasoline and diesel modifications of cars. When the ignition is functioning, the driver can open and close the doors. The range of the key fob in the 625 model is 2 kilometers in open areas. The cost of the complex is about 3,300 rubles.
2. QX 270. There is a feedback option, service mode and remote engine start. The alarm has a Panic function, the activation of which is accompanied by a visual and audio alert. The package includes a temperature and sensitivity controller; it is possible to activate the security mode when the engine is running. The range of the pager with signaling is 300 meters. However, the security complex can send messages to the remote control if it is within a radius of 800 meters. The device will receive messages about an attempt to break into the car. You can configure the activation of the security mode automatically. The operating temperature range varies from -40 to +85 degrees. The cost of the complex is 4500 rubles.
3. QX 44. The system is equipped with all standard functions aimed at ensuring the safety of the machine. The security complex warns car owners about a possible threat by sending a message to a pager. The key fob screen displays information about the battery charge. You can implement the option of automatically closing the doors when the ignition is activated. When configured and programmed, the pager's operating range is 30 meters. The package includes two remote controls. There is a Comfort function that allows you to open the car door locks without pressing the corresponding key fob button. The security system recognizes the car owner using the key as he approaches the car. You can configure the functions of automatically closing doors when you press the brake, self-diagnosis, passive testing, as well as silent disabling of the security mode. The cost of the complex is about 3 thousand rubles.
4. SLR 5625 B. This car alarm also has a feedback option. The vibration alert function is implemented, the remote control is equipped with a screen. If necessary, you can configure the operation of the door closers that ensure the closing of the electric windows. The tailgate can be controlled. There are options for Panic and switching to service mode. You can enable or disable remote engine start using a timer. The function of silent activation of the security mode has been implemented; you can turn on the protection when the engine is running. If the car is stolen, the security system will automatically block the operation of the power unit. The communication channels through which signals are transmitted are protected by encryption from interception and scanning. The range of the remote control is 800 meters. The cost of the complex is 4500 rubles.
5. 868rs. In this system, the developer has implemented the ability to configure the duration of operation of the power unit after a remote start. Secure communication channels are used to transmit data, which eliminates the possibility of signal interception by attackers with a code grabber or other scanner. The security complex is fully integrated with vehicles equipped with any type of transmission - manual or automatic. You can start the motor based on temperature by setting the temperature threshold in advance. If, after starting, the power unit stalls for some reason, the alarm can trigger the option of quickly checking the problem. The system monitors the functioning of the engine using the engine fluid pressure indicator; you can monitor the operation of the unit using the tachometer. The price of the device is about 5,000 rubles.
6. The 675 uses Beearm technology feedback. It also has the option of remote engine start. Enhanced dynamic BACS is used to provide additional security. This allows you to protect the pager channel from interception of pulses and scanning by grabbers. The developer assures that the security complex was designed specifically to function in the harsh conditions of the north. The security system is fully adapted to work with electronics and equipment in modern cars, regardless of configuration. The car can be equipped with a diesel or gasoline engine, automatic or manual transmission. The main difference of this system is the presence of the Intellistart option; its implementation is possible with advance configuration of the manual transmission. The pager screen displays all the necessary data regarding the operation of the system. The price of this car alarm is about five thousand rubles.

An overview of the 675 model is presented in a video filmed by the AutoAzart channel.

How to install correctly?

In accordance with the installation manual, Panther systems are installed on vehicles with the on-board power supply disconnected, so the battery must be disconnected. You can also connect all alarm elements to a 12-volt power source in advance to make sure it is working.

Recommendations for placement and installation

Tips for the location and installation of alarm elements:

1. The control unit is installed inside the car, in the most hidden place. For additional protection of the module from water and vibrations during movement, the device can be wrapped in cellophane and foam rubber. The block is placed with the block down to prevent drops of condensation from flowing down the wires onto the board. It is recommended to install the module behind the instrument cluster to ensure a minimum wiring length when connecting.
2. A transceiver with an antenna and a built-in temperature sensor is installed on the car window. For installation, you need to use the rear window; if there is a protective film on the windshield, the latter can cause a shielding effect. The surface on which the transceiver is installed is cleaned and degreased in advance. Do not install the antenna near electronic equipment or metal devices, as this will reduce the range.
3. The siren is located under the hood. The device must not be installed near the cylinder head or metal surfaces adjacent to it. The siren should be placed with the horn facing down to prevent moisture from accumulating inside.
4. The impact sensor is mounted in the vehicle interior; it is recommended to place it in the central part of the body. During installation, it is necessary to ensure free access to the controller's adjusting elements.
5. Additional regulators are installed in accordance with the recommendations specified in the service manual.
6. The button to enter the service mode is located in the vehicle interior. It must be installed secretly.
7. Limit switches are installed on moving body elements. Installation of triggers is not allowed in drains or places where moisture accumulates.

Connection diagram

General electrical diagram for connecting the microprocessor unit

Laying and connecting wires

Laying of power lines should be done under the decorative cladding in the car interior. There should be no moving mechanisms or components at the installation site. To better protect the wires from rapid wear and tear, the electrical circuit can be wrapped with electrical tape.

Table: connecting the main connector (main block of the block)

Table: Connecting the power connector (6-pin power output)

Connecting electric lock drives

Electrical diagram for connecting central locking drives:

Electric drive connection diagram

If the vehicle is not equipped with central locking, you can install additional drive devices:

• black-green and black-blue contacts are connected to “ground”, that is, any bolt screwed into the car body;
• red-green and red-blue outputs must be connected directly to the battery or any electrical circuit where 12-volt voltage is always present;
• the white-green contact is connected to the blue opening input of the electric drive;
• The blue/white pin should be connected to the green closing output of the actuator.

Connecting additional connectors

Connecting additional connectors on the microprocessor unit:

• a four-pin white connector is designed to connect a shock and sensitivity controller;
• a two-pin blue block is used to connect the button to enter the alarm service mode;
• The white two-pin connector is designed to connect an LED indicator of the anti-theft system status;
• The black five-pin block is used to connect the external transceiver module.

Types of pantera car alarms

There are various modifications of this pantera security system on the market, the alarm of which is designed to inform the driver about the condition of his car, as well as start the engine at a distance or within a certain period of time. Therefore, the Panther alarm is suitable for any car (even an automatic transmission).

The developers tested it in various atmospheric temperature conditions, and therefore its use is permitted in cars operated in the far north or Asia.

The developers of these products have created the following types of security systems.

1. Single-sided models. They have the following modifications: pantera xs 1000, qx 77, qx 44, CL 500, CLK 355. They are characterized by the fact that they are equipped with an emergency alarm shutdown function using a special button, which is encoded with a pin code (model xs 1000), have two-level shock sensors, which makes it sensitive to any damage, even minor ones. This also includes protective coding of the signal, which prevents it from being read by scanners (models xs 1000, CL 500, CLK 355), and of course this is an alarm with auto engine start, plus a 6-channel siren. In general, the xs 1000 model is one of the flagship panther one-way alarm systems.
2. Double-sided models. These include pantera slk 675rs, slk 468, clc 180, slr 5625. They are characterized by an improved anti-theft system, constant communication with the car owner about the condition of the car, the remote ability to turn off the engine in case of illegal possession, regulation of the engine starting capabilities (turning on at a certain temperature air, low battery charge). In addition, the installed additional sensor will be able to turn off the engine while it is moving.

But before you start using this alarm, it is important to remember that its range in feedback mode does not exceed 2 kilometers, and in remote engine start and lighting mode, no more than 300-700 meters. This does not apply to the function of starting the engine at a certain air temperature, or low battery charge

This all happens automatically.

User manual

In accordance with the instructions for use, operation of the anti-theft system is possible only after checking that the alarm system is connected correctly. To do this, you need to turn the vehicle security mode on and off. When the function is activated and deactivated, the door locks should open and close.

Setting up the control panel

Before using the remote control, the user must install a working battery into the device. The battery is inserted into a special compartment located behind the back cover of the key fob. When installing the battery, you must take into account the polarity.

Meaning of buttons and indicators

The system includes one 5-button key fob transmitter with 2-way communication and an LCD display and one 4-button communicator.

Location of buttons on the main and additional key fob of the Panther alarm system

Description of the symbols located on the display of the main key fob:

1. Indication of the power source located in the pager.
2. Second additional channel.
3. The car alarm service mode has been launched.
4. The car's power unit is started.
5. Open luggage compartment.
6. Icon of unlocked door locks, one or more.
7. The function of automatic reactivation of the security mode is enabled.
8. The hood of the car is open.
9. The function of alerting the user via vibration signals is enabled.
10. Daily engine start mode is activated.
11. The handbrake lever is disengaged.
12. Function of calling the car owner from the passenger compartment.
13. The remote start mode of the power unit based on ambient temperature is enabled.
14. The communicator receiver is activated.
15. Indication of communication with the vehicle.
16. Icon for determining the physical impact on the car body.
17. The remote control battery saving mode is activated.
18. Open or closed door locks icon.
19. The alarm option is activated.
20. Indication of the second half of the day.
21. First half of the day.
22. Silent vehicle security is enabled.
23. Car protection with sound signals.
24. Displays current time and temperature.
25. Temperature scale indication.
26. The countdown timer is activated.
27. Ignition on indicator.
28. A—Anti-robbery mode is enabled or disabled.
29. B - icon for the operation of the third additional channel.
30. C—autostart of the power unit based on temperature is activated.
31. D - daily remote engine start.
32. E - remote engine start or stop icon.
33. F - silent vehicle protection.
34. G - full-fledged vehicle security with siren sounds.
35. H - remote disabling of the sensitivity controller.
36. I - service mode for servicing the anti-theft system.
37. J—machine status and engine temperature icon.
38. K - second additional channel.
39. L - remote opening of the tailgate.

Indication of icons on the display of the Panther remote control

Key fob programming

For the CLK 355 model, the communicator is linked as follows:

1. The vehicle's security is turned off.
2. Over the next five seconds, the ignition is turned on.
3. Over the next 5 s, the user presses the button to enter the service mode three times.
4. Then you need to wait until the siren sounds once.
5. The ignition system is turned on. Two sound pulses should sound - one longer, the second short. This will cause the LED light to start blinking.
6. Over the next 10 seconds, any button on the assigned communicator is pressed. If programming is successful, the siren will play one long signal.

In the LX-320 model, binding is done differently:

1. The ignition is activated.
2. The service mode button is pressed and held. It can be released after the siren sounds 4 sound pulses.
3. The first button on the communicator (with the closed lock indicator) is pressed. If an additional key fob is attached, a similar control is used.
4. The same steps are performed to program the remaining key fobs. The time between pairing devices should be no more than five seconds, otherwise the alarm will exit the setup menu.
5. The ignition in the car is turned off. The external lights should blink five times.

Video: binding the Panther keychain

The “In the Garage” channel in its video demonstrated in detail how to set up a communicator from the Pantera security system.

Turning security modes on and off

The security function is activated by pressing a button with an indicator in the form of a closed lock. The press should be short-term, and in confirmation the system will give one sound and light signal. If you want to enable silent security, the indicator on the key fob display must be moved to the position of the corresponding indicator and the second button pressed. This means key II.

You can turn on car security with the engine running like this:

1. The parking brake on the car is raised.
2. On a car with the power unit running, press button I. It must be held for several seconds until the communicator emits a melodic signal and the external lights blink.
3. The ignition in the car is turned off. The key must be removed from the lock. The motor should remain running.
4. Then the user must leave the car and lock all doors. Press the key with the closed lock icon. After this, the alarm should block the operation of the engine and other components.

Activating the protective function without using a key fob is done as follows:

1. The car's ignition turns on, but the engine does not start.
2. The button to enter the service mode is pressed eight times.
3. The ignition is deactivated. The siren and external lights should sound once each.
4. In the next twenty seconds, the user must leave the car and lock all door locks with the key. After 20 s, the protection mode will be activated.

It is important to know

Disabling the normal security mode is done by briefly pressing the key with the key fob open. The protection is deactivated in a similar way on a car with the engine running.

Emergency shutdown of the security function is performed as follows:

1. The vehicle door is opened with a key. The system siren will sound.
2. The ignition is activated, but the engine does not start.
3. Over the next twenty seconds, the service mode button is pressed four times.
4. The ignition turns off. When the security mode is turned off, the external lights will work twice.

Setting up autorun

You can start the engine in several ways:

1. By temperature. To activate the option, the cursor on the key fob screen is moved to the indicator with a thermometer and the inscription “Start”, after which key II is pressed. An icon with an indicator in the form of a thermometer will appear on the remote control display. Disabling the option is done in the same way.
2. By timer. The principle of setting and disabling the option is identical. Only now the user must select an icon on the key fob screen with the inscription “Start” and an indicator in the form of a dial.

If you want to start the power unit on command, you need to hold down the I button on the remote control. This element is held for three seconds, after which the engine should start.

Restoring factory settings

If one of the functions does not work or functions incorrectly, you can try to solve the problem by resetting the parameters.

To do this you need to do the following:

1. The car's ignition system turns on.
2. The button to enter the service mode is pressed ten times.
3. The ignition in the car is deactivated. If the siren then beeps ten times, this indicates that the reset menu has been entered.
4. The service button is pressed once. The siren will sound.
5. On the communicator, the closed lock control is pressed. If the parameters are successfully reset, one beep will sound.
6. To leave the menu, the ignition is activated.

Why does the alarm not work and how to fix it?

Failures in the operation of the complex can occur for the following reasons:

1. The battery in the pager is low. The problem is solved by replacing the dead battery with a new one.
2. The key fob fell into the water and no longer transmits signals. Try drying the pager by placing it in a warm place, near a radiator or stove, but not in close proximity to them. If this does not help, disassemble the remote control and leave it in this condition for a day. If the problem persists, the device will need to be repaired or replaced with a new one.
3. All doors do not close. The cause should be sought in damaged wiring. Diagnostics of electrical circuits is carried out using a multimeter. If you don't know how to check the wiring, contact an electrician.
4. The antenna adapter connection cable is damaged. If the transceiver is not working, transmitting pulses will not be possible. Diagnostics of electrical circuits is performed. Damaged wires are replaced with new ones or restored, depending on the nature of the damage.
5. The contacts on the control unit have oxidized. This problem can occur as a result of exposure of the device to moisture. It will be necessary to dismantle the module and clean the contacts from dirt and oxidation. Check the connectors themselves; there may be oxidation on them too.
6. The control unit has failed. It is difficult to solve this problem at home. Detailed diagnostics of the device will be required. You can try to solve the problem by flashing the module. If water gets on it, you can try to dry the device.
7. The siren goes off for no reason. You need to check the sensitivity sensor. The cause is usually due to improper adjustment of the controller. Setting up the sensor will solve the problem.

Download installation and operating instructions in PDF format

You can download technical documentation for controlling and installing Panther alarms using the following links:

Current manufacturer models

Types of security systems produced under the Pantera brand:

• with a 2-way communication channel without automatic start function;
• equipment that supports remote or automatic engine starting;
• budget alarms equipped with 1-way communication.

SPX-2RS

The complex supports the car's CAN bus; the operating parameters of popular transport models are pre-entered into the equipment's memory. Additional FLEX channels are supported with the ability to intelligently configure. To prevent command interception, 128-bit encryption keys are used.

PR-2

The alarm system is distinguished by the use of a double dialogue code to encrypt key fob signals. The operating frequency of the transmitter is 434 MHz, the range of the remote control does not exceed 1200 m. The complex is connected to the car’s digital bus, which allows you to implement the Slave function (control of the alarm system using a standard key).

SLK-775RS

The equipment operates at a frequency of 434 MHz, the range of the remote control reaches 1500 m (reception of signals). The complex supports automatic engine start based on a signal from the voltmeter, providing battery recharging. A block is provided for quickly determining the causes of premature shutdown of the power unit.

SLK-868RS

The signaling is distinguished by the frequency of the transmitter, increased to 868 MHz. Increasing the parameter improved signal transmission and increased the operating radius to 2000 m. The equipment is equipped with additional channels that allow you to control the luggage compartment lock or other devices.

Advantages and disadvantages of Panther systems with autostart

List of benefits:

1. A large selection of different models, differing in characteristics and functionality. On sale you can find both cheap automatic start systems and more expensive options.
2. Ability to control the system using a mobile device. This can be implemented only by modern versions of Panther.
3. Versatility. This allows you to use the Panther alarm on any car that meets its parameters. The system can be installed on diesel and gasoline engines, as well as on vehicles with manual and automatic transmissions.

According to consumer reviews, the disadvantages of such alarms are as follows:

1. Rapid discharge of the battery in the key fob. The presence of an energy saving mode does not solve this problem, especially during the initial setup of the system. The average battery life is about three months.
2. Dynamic signal encryption technology is an outdated encoding option. This technology is used on some modern models. It should be taken into account that a professional criminal can easily bypass such encoding.

One-way systems

One-way systems are much simpler in design, which has a positive effect on their service life. This fact also reduces the price of the device.

One-way car alarms "Panther" are easy to use and very reliable. In addition, they integrate all modern security technologies, such as SuperKeeloq dynamic code. It is extremely difficult to hack.

You should also note the Anti-HiJack mode and additional engine blocking in case of car theft. A useful innovation in Panther car alarms are sensors with two sensitivity levels. The correct setting allows them to distinguish between a blow aimed at destruction and an accidental contact with a passing passerby.

Modern car alarms allow you to control many systems inside the car. For example, you can turn on the lights while being a kilometer away from the vehicle. This option can be very useful if you need to convince intruders that there is someone in the car.

Important! Some models of Panther car alarms make it possible to control power windows.

Another significant advantage of Panther car alarms is the central locking. It allows you to unlock and lock the doors while approaching the car. This function can be very useful, especially when every minute counts.

Panther car alarms have a number of programmable functions. You can add or remove them if necessary. It is also possible to make adjustments to the work and fine-tune.

Important! It is worth noting that two-way systems have most of these functions by default.

What is the price?

Approximate prices for the purchase of Panther anti-theft systems:

How to set the time on a Panther keychain

Correct display of the current time on the remote control screen is very important. After all, the clock turns on and off the most important functions: timed autostart, turbo timer, etc. The following instructions will help you set the clock correctly.

1. To enter the setup mode, hold down the F key for five seconds.
2. The key fob will emit two short beeps.
3. The watch face data will flash on the screen.
4. Using the “Trunk Opening” button we increase the clock value. Use the “Star” key to decrease the readings.
5. To set the minutes, briefly press the F key.
6. By clicking “Open trunk” we increase the minutes value. Use the “Star” button to lower it.
7. Hold F for five seconds to exit time setting mode.

Video: setting up autorun

The “Sigmax69” channel, using the Panther 625 model as an example, showed the process of setting up automatic engine start.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (100.00%)

No

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 2 votes, average: 5.00 out of 5)

Discuss the article:

SLK-868RS alarm connection diagrams

If you do not need to equip the motor with autostart, connect only the main connector (16 PIN). Its “red” (PIN 2) as well as the “red-white” cord receives power. In general, you need to implement the following scheme:

How to connect power

The purpose of other wires is described further.

Low-current signal connectors

Wiring of the main terminal block

The “green-black” cord is connected to the hood end, but a thermistor can be connected in parallel. And through the “purple-yellow” wire, the system determines whether there is “12 Volts” on the starter. Connect the cord to pin “50” of the lock.

The purpose of some wires will have to be programmed. The following instructions are suitable for Pantera alarms:

1. If the “purple-white” cord is connected to the tachometer, then function “9” is assigned the value “2” (the default is “3”);
2. To make the "yellow-black" wire control the crawler, options "13" are set to "2";
3. The purpose of the “brown-white” cord is specified by option “12”. For cars with a manual transmission, set the value to “2” (first set to “1”).

Let’s say the microphone on the “brown-white” cable is connected to ground, that is, a signal of reverse (minus) polarity is used. Then, be sure to follow step “3”. The manual also provides explanatory diagrams.

How to connect low-current circuits

Central lock connector pinout

Connecting the power connector

To implement a circuit with autostart, connect a 6-pin “power” terminal block:

Connector 6 pins, connection

There is no “+12 Volt” on the IGN2 contact when the starter is started. If the lock has an IGN3 contact that switches reverse polarity voltage, connect a relay. But reading the reviews, you can understand that this option is undesirable.

The signal is connected to pin “50” thanks to a low-current cord. And current is supplied to the starter through the “purple” wire. You can perform installation in the reverse order, restoring the break circuit. Then you get a system without autostart.

Remote engine start and shutdown

To implement this function, the car must be in an open or ventilated parking lot. You should first:

• apply the handbrake or put the automatic transmission lever in the PARK position;
• set the air conditioner settings;
• switch the ventilation system to recirculation mode.

Remote engine starting is performed by pressing the “*” button of the main or additional key fob 2 times with no more than a 3-second break.
Acknowledgment occurs through the short-term activation of the turn signals. In case of failure, the engine starts (the starter cranking time can be changed) a maximum of three times. The air conditioner and other preset devices turn on 1.5 minutes or a preset time interval after the engine starts running.

Engine operation time after remote start or interior warm-up time is limited to 12 minutes or other programmed value.

You can turn off the car remotely using the “*” button. The activation of the system is confirmed by an acoustic signal or a 2-second vibration signal.

Additionally, the key fob display is switched to the current time display mode.

What to do if a malfunction occurs

As with any technical device, malfunctions can sometimes occur. Let's consider several possible situations of this kind.

The range of the key fob is very important for the safety of the car. If it begins to rapidly decrease, then something needs to be done about it. In this case, the most likely cause is a dead battery. This is a possible, but not the only reason.

In order for the security system to recognize the key fob, it needs to “remember” about it, remember its data. To correct this, you need to carry out the procedure for initializing the key fob data, which is described in the operating instructions.

If the key fob stops working due to a discharged car battery, due to possible sudden exposure to an electromagnetic field or due to very low temperatures, then its operation may change unpredictably, first you need to make some attempts to correct this situation. To do this, it is necessary to carry out an emergency shutdown and, having driven some distance, check the operation of the system. Sometimes repeatedly pressing the key fob buttons can help.

If the malfunction continues to occur, then the next step is to disassemble the key fob. It needs to be unscrewed and checked for dust and dirt and for the integrity of the contacts. It is also possible for liquid to penetrate into the key fob. You need to clean it and check the health of the system.

Programming Pantera SLK-75SC

In order to program the Pantera SLK-75SC you need to follow the instructions:

• Disarm the system.
• Turn on the ignition.
• Press the Valet button the number of times corresponding to the selection of the desired mode in the table below.

• Press and hold the “Valet” button until the siren beeps.
• While continuing to hold down the Valet key, press button 1 for mode 1-2 or give any signal if 3-6 is activated.
• Turn off the ignition

Alarm Features

The device with which control is carried out is a key fob. It has five buttons with which you can give commands. Communication is two-way. To provide the necessary information, the key fob is equipped with a small liquid crystal display.

In addition to the main key fob, the kit also includes an additional key fob with four buttons. The radius at which two-way communication is ensured is one thousand meters. If we talk about the distance at which an information signal can be transmitted, then we are talking about two thousand meters.

How the key fob works

Once upon a time, the very first models used static code. Due to the fact that it constantly retained its value, there was a high probability of hacking and, as a result, the ability to turn off the alarm if it was stolen. This level of security was clearly insufficient.

Later, the creators began to use much more secure dynamic code. The principle of its operation is that each time a command is issued by the key fob, the access codes of both the key fob and the entire security system change.

Since this approach uses a different code each time, the likelihood of hacking has sharply decreased. However, such a possibility still exists.

In modern models, the principle of operation of the key fob has been improved again. The dialog model of code modification is taken as a basis here. The point is that its formation occurs in three stages.

1. The key fob communicates with the security system.
2. Based on the received data, a special signal is sent to the key fob.
3. Taking into account the information received, the key fob makes changes in the security system codes.

This security system makes it almost impossible to hack the system's access codes.

Contents of delivery

This system consists of several parts. After purchase, they must be carefully installed. If the driver has some skills in working with such equipment, then he can carry out the installation without much difficulty. If this seems too difficult, then it makes sense to contact an appropriate specialist. Let us list the main devices that make up the Panther.

• Main electronic unit.
• A key fob with a display and five control buttons.
• Additional keychain. It does not have a display and only three control buttons.
• The shock sensor is two-level.
• Siren to give a loud sound signal.
• A relay that is designed to block the engine upon command from the security system.
• A special block with wires designed for installing a blocking relay.
• LED indicator, along with its own cable.
• Push-button switch for Valet operating mode. Sometimes you may wonder what this mode is for. The point here is to disable some protective functions when the driver needs it. This situation, for example, may arise during the process of washing a car.
• The delivery set includes a limit switch.
• Set of wires.
• Instructions.
• Package.

Please note that we are talking here about the standard delivery set. Possibility of expansion is provided.

As an example, we can talk about the possibility of installing GPS sensors. Such additions will increase the level of safety for the car.

Features of the alarm CLK 355 375 455

These are budget alarm models of the Pantera brand. To record key fobs, do the following.

1. Remove the security mode.
2. Turn the ignition on and off within five seconds.
3. Press the jack key three times. Do it in five seconds. One long siren sound will sound.
4. Activate the ignition. 1 short and long CHIRPS will follow. The LED will flash slowly. The system is ready for programming.
5. Within ten seconds, click on any key on the first key fob. The system will emit one long beep. The main pager code is stored in memory. The LED will light up continuously.
6. Carry out the same actions with the remaining remote controls.
7. After entering the data of the fourth key fob, the control unit will exit the recording mode. A short and one long siren sound will follow.