Signs of a broken cylinder head gasket, troubleshooting, replacement features

The cylinder head gasket is an element of an internal combustion engine installed between the cylinder block and its head. Designed to prevent the escape of gases from the combustion chamber, as well as lubricating and cooling liquids from the channels through which they circulate.

Damage to the cylinder head gasket can lead to leaks from under the head, decreased compression, engine tripping and loss of power, overheating, problems with the stove, etc.

The easiest way to recognize a malfunction is by external signs: the presence of oil leaks, a sharp increase in its level and a change in color, the appearance of carbon deposits on the spark plugs, exhaust gases “shooting” from under the cylinder head when the engine is running and a change in their color when exiting the exhaust pipe.

Below we will consider whether it is possible to drive with a broken cylinder head gasket, what are the signs and reasons for its breaking, and will dwell in detail on the methods for checking and eliminating the malfunction. Let's discuss the subtleties of choosing this element of the internal combustion engine.

Is it possible to drive with a broken cylinder head gasket?

Car owners often ask whether it is possible to drive with a broken cylinder head gasket. It is not always possible to immediately fix the problem, for example, when the malfunction occurs on the road or far from a service station.

Experts say that it is impossible to travel in such a situation. This is especially true if antifreeze gets into the oil or vice versa. The only way out is to move only in tow. If you ignore this requirement and drive even 200-300 km, the engine may need to be overhauled.

In a situation where oil and antifreeze do not mix, driving a short distance is allowed. Here we are talking about minor damage, but it is necessary to monitor the engine temperature and coolant level. After all, if the gasket is punctured from the inside, then there is a high risk of damage to the valves and pistons as a result of antifreeze getting into the cylinders.

Symptoms of malfunction

As mentioned earlier, the main task of the gasket is to completely seal the combustion chamber and prevent antifreeze from entering the oil and fuel blocks. The difficulty lies in the fact that depressurization of the structure often occurs. Therefore, if the cylinder head gasket is blown, the symptoms can be very ambiguous:

• the temperature of the engine begins to increase without good reason;

• compression decreases, the engine begins to stall, and ignition may occur;

• the oil level in the crankcase increases, an emulsion appears, an emergency light comes on, indicating oil pressure;

• the cooling system hoses swell and the reservoir safety valve begins to operate. Antifreeze becomes cloudy;

• the heating system of the car interior does not work;

• white and thick smoke appears from the exhaust pipe;

• oil or antifreeze begins to leak.

If the cylinder head gasket has blown, what signs exist are discussed above. Each symptom has a high danger.

Signs of a broken cylinder head gasket

The main difficulty for novice car owners is to promptly detect damage to the cylinder head gasket. Almost all cars are in the “risk zone”, but most often the problem is faced by owners of Niva Chevrolet, VAZ 2106, 2109, 2110, 2112, 2115, 2114, 2107, BMW E39, Opel Astra, ZMZ 406, Daewoo Lanos and Kalina. This is an incomplete list of cars in which the cylinder head gasket periodically fails (burns out). Symptoms of a malfunction may differ depending on which area is broken.

Damage to the cylinder head gasket between the cylinders

In VAZ cars and a number of other models, the gasket very often burns out between the second and third cylinders.

The easiest way to recognize a malfunction is by the following signs:

  1. Uneven operation of the engine during operation of which you will feel a missing spark plug due to coolant or oil getting into it. As a result, the internal combustion engine will triple.
  2. Reducing engine compression. Damage to the cylinder head gasket leads to exhaust gas leaking from the cylinder block during the piston stroke, causing compression in the problem area to drop or decrease to minimum values.
  3. Addition to clause 2. At the moment when a compression stroke occurs in one cylinder, and a power stroke occurs in the adjacent one, when the gasket is broken, the exhaust gases, in our case, of the second cylinder are mixed with the air-fuel mixture of the first. This will lead to problematic starting of the engine, but after warming up the latter operates stably.

To diagnose the problem, it is enough to remove the caps of the high-voltage wires from the spark plugs one by one and pay attention to changes in the operation of the engine.

If no changes occur when removing a cap, this may indicate damage to the cylinder head gasket in this area. Also check the compression in the engine cylinders.

Damage to the cylinder head gasket between the cylinder and the cooling system

Sometimes the problem occurs between the cylinder and the cooling channel. In this case, the malfunction can be recognized by the following symptoms:

  1. Uneven operation of the power unit (as in the previous case). A cylinder spark plug that gets antifreeze on it will not work.
  2. Reduced coolant level. This factor is explained by coolant leakage due to a violation of the integrity of the gasket.
  3. Formation of steam or air bubbles inside the expansion tank. It is better to carry out diagnostics on a cold internal combustion engine, because when checking “hot”, the cause of the problem may be poor-quality coolant. The problem occurs due to exhaust gases entering the cooling system. For diagnostics, you can put a rubber glove or a condom on the outlet of the expansion tank. We will dwell on this issue below.
  4. The appearance of thick white smoke from the exhaust system. Appears due to active vaporization. This is facilitated by the combustion of antifreeze in the combustion chamber and subsequent removal through the exhaust pipe.
  5. The presence of a kind of “emulsion” in the expansion barrel. Car owners often call it “mayonnaise” or “sour cream” because of its characteristic yellowish color. The reason is the mixing of antifreeze and oil. The problem can be identified by looking into the tank or removing the oil level dipstick from the engine.

Other signs

There are a number of other signs that can be used to draw conclusions about a damaged cylinder head gasket.

Let's briefly look at their features:

  1. Exhaust gases exit from under the cylinder head. The symptom appears when there is damage between the cylinder and the outer part of the cylinder head. This is because gases find their way through the damaged area of ​​the gasket. If the gasket burns out significantly, loud sounds uncharacteristic of engine operation will be heard.
  2. The appearance of oil at the junction of the head and cylinder block. If the integrity of the gasket is damaged, it allows lubricant to leak out and contaminate the outside of the engine.
  3. Problems with the stove. Due to disturbances in the cooling system, difficulties arise in warming up the interior. Gases from burnt fuel enter the “corridors” of the cooling system. As a result, air reaches the heater heat exchanger, which works worse.
  4. Soot or moisture on spark plugs. To diagnose, unscrew the spark plugs one by one and look at their condition. The appearance of oil or antifreeze on the contacts, as well as carbon deposits, often indicates a violation of the integrity of the cylinder head gasket.
  5. Increase in oil level. This occurs due to antifreeze entering the lubrication system.
  6. Engine overheating. Damage to the cooling and lubrication system impairs heat dissipation, and the engine quickly gains temperature.
  7. Release of coolant from the exhaust system. Antifreeze droplets fly into the air, which are easy to diagnose.
  8. Deterioration of internal combustion engine characteristics. Indirect signs of a malfunction include an increase in the “gluttony” of the motor, a decrease in power, etc.
  9. Increased pressure inside the cooling system pipes. A hole in the gasket where the coolant passes through will result in exhaust gases entering the cooling system pipes. The latter, due to the creation of increased pressure in them, will be very hard (like stone) to the touch.

Please note that it is necessary to analyze the malfunction as a whole. For example, the appearance of carbon deposits on spark plugs or problems with the stove may indicate other malfunctions of the machine.

How to troubleshoot

There should be no minor repairs here. Gone are the days when the gasket was changed without even removing the head from the engine, but only by lifting it. So, at best, you can only simply destroy the new part.

Even when asking for repairs, you cannot ask to change the gasket. The correct wording here is to eliminate the cause.

  1. After removing the cylinder head, you need to find out exactly what happened and for what reason. Without finding a specific sequence of events, it is better not to assemble the motor. And only after understanding everything, you can begin to eliminate it.
  2. The surfaces of the head and block must be cleaned and brought into perfect plane using measuring tools and machine tools, if necessary. There is no need to hope that the gasket will fix everything by adjusting to the unevenness. It doesn't work like that.
  3. The fastening bolts are replaced with new ones; those that have worked in the fluidity zone of the material are unreliable, even if the dimensions are still normal. The threads must be clean, oil and antifreeze from the blind holes must be completely removed by blowing.
  4. Installation is carried out strictly according to technology; there is no need to do any experiments or transfer of outdated fastening methods from the last century.
  5. In some engines, it is necessary to take into account changes in the volume of the combustion chamber due to repeated milling of surfaces - the compression ratio changes.
  6. The cooling and lubrication systems will have to be thoroughly flushed; no traces of emulsion should remain. Of course, oil and antifreeze are replaced.

At first, operation should be carried out as if the engine were running in, without heavy loads and with temperature control. It is quite possible that something was missed during the repair; there is no need to aggravate the situation.

About mixing oil and antifreeze

The appearance of antifreeze in the oil or vice versa is one of the main signs of a broken cylinder head gasket. In this case, the operation of two systems at once is disrupted: lubrication and cooling.

In the future, rings and pistons may become deformed, and engine efficiency will decrease significantly. You cannot drive a car with such a malfunction; it is better to immediately go to a car service for repairs.

When mixing oil and antifreeze, other consequences may occur:

  • clogging of cooling system elements with oil, which reduces their efficiency;
  • damage to rubber or plastic elements of the cooling system (CO);
  • overheating of the motor even in cold weather and reducing its service life, etc.

Due to mixing of the two compositions, a yellowish emulsion appears. Its appearance requires not only replacing the cylinder head gasket, but also performing other repair measures. Be sure to clean the CO, the pan and the channels through which the lubricating fluid flows.

The most unpleasant consequence of oil getting into antifreeze is engine wedge. This occurs due to the appearance of rust on the cylinder walls. The problem is especially acute on diesel engines.

As the engine cools down, coolant enters the combustion chamber, and upon subsequent start-up there is no longer enough coolant in the CO. If you do not track this moment on the instrument panel, the power unit may jam.

An additional disadvantage is the increased formation of soot, which subsequently settles on engine elements. The oil filter that suffers the most is the one that requires replacement. But this work can only be done after eliminating the cause of the leak (in our case, installing a new cylinder head gasket).

Characteristics

The engine consists of two parts: the head and the cylinders. The combustion chamber is protected by a head that covers the structure. The chamber is equipped with a special valve mechanism and camshaft. The valve cover is fixed on top.

Considering a 4-cylinder engine, there will be the same number of round-shaped holes, as well as several bolts for fastening. Special channels help circulate air mass as well as coolant. In practice, there are products made from copper, asbestos and graphite.

It is important to note that gaskets do not belong to a special category of components. What will cost more is not the purchase of a new product, but the installation process. This is due to the fact that a specialist will have to disassemble the engine, and then set up the system responsible for gas distribution.

The main functions of the cylinder head include the following aspects:

• ensuring a sealed state for the combustion chamber;

• preventing gas leaks;

• reducing the risk of oils and liquids entering the combustion chamber;

• the possibility of mixing liquids is eliminated.

In practice, inexpensive asbestos options are most often installed. Therefore they burn out much faster. As a result, coolants and other substances enter the combustion chamber. The main danger is that the oil film, which acts as a protective barrier, begins to gradually wash away. As a result, the service life is sharply reduced, and the pistons may jam.

Signs of engine overheating

When diagnosing a breakdown, it is important to correctly determine the fact of engine overheating.

There are several main features here:

  1. Sharply rising coolant temperature according to the indicator in the cabin.
  2. The appearance of condensation on the surface of the unit.
  3. Steam from under the hood.
  4. Reduced power.
  5. Noisy and rough operation of the internal combustion engine, detonation, and will not start.
  6. White deposits on the spark plug electrodes.

Operation of the machine in case of overheating of the internal combustion engine is prohibited, because this is fraught with its wedge and the need for major repairs.

How to find out if the cylinder head gasket is blown

The greatest difficulty for many car owners is to determine that the cylinder head gasket is the cause of the problem.

To check, follow these steps:

  1. Start the engine and inspect it. Pay attention to the presence of smoke from the gap between the head and the cylinder block itself. During operation there should be no ringing or other suspicious noises that have not previously been observed.
  2. Inspect the expansion tank of the cooling system, the container for filling the lubricant and the radiator cap for the appearance of a reddish emulsion. If the lubricant gets into the antifreeze, traces of the emulsion can be seen on the cap of the expansion tank and radiator tank.
  3. Check compression in different cylinders. Its sharp decrease may indicate a broken gasket; also read why different compression occurs in the cylinders.
  4. Start the engine, let it run and look at the condition of the exhaust gases. The appearance of thick white smoke often indicates damage to the element in question. Pay attention to the smell of smoke. If you use antifreeze in the cooling system, it will be slightly sweet.
  5. Check the fluid level in the expansion tank. Its decrease indicates a problem.
  6. Measure the engine oil level. If antifreeze gets into the lubrication system, you may notice a rise in the level above the MAX mark.
  7. Open the radiator/expansion tank cap and check the coolant for gas emissions. For diagnostics, you can use a rubber glove or bag (we will discuss this in detail later).

Additionally, pay attention to the signs of a broken gasket, which were mentioned at the beginning of the article.

Fault detection methods

If the driver has even the slightest suspicion that the gasket has failed, it is worth contacting a technical center as quickly as possible. However, you can carry out a quick diagnosis on your own. It is enough to prepare the simplest means and tools. The main thing is to have at least minimal knowledge of physics.

Listed above are the main signs that indicate a breakdown. All that remains is to correctly determine the location of the fault.

Using a Glove or Balloon

If gas has entered the cooling system, this malfunction can be recognized by a specific smell. However, it is not always possible to determine it against the background of other possible odors.

You can try putting a rubber device on the neck. If the gas does escape, it will inflate the glove or child's balloon, which will be a major sign for the car owner. Such an experiment makes it possible to quickly establish the transmission of gases. Conduct the experiment without the engine running, otherwise the antifreeze will boil.

Using the bottle

The bottle is used according to the same principle. Fill the bottle with water and make a hole into which the hose will be inserted. The second end must be tightly connected to the hole in the tank. If gases are present, the liquid will definitely show this.

Why does the cylinder head gasket break?

Car owners often ask why the cylinder head gasket fails and gets damaged. Let's highlight the main reasons.

Overheat

Most often, the cylinder head gasket burns out due to engine overheating, so it is important to identify the problem at an early stage and fix it. Due to changes in temperature conditions, the block cover “moves away” and the contact between parts of the motor deteriorates. The result is a lack of tightness of the power unit with consequences for the gasket.

As a rule, aluminum cylinder heads are susceptible to this problem. The cast iron head (installed on diesel engines) is more resistant to temperature changes. But it may become deformed or damaged.

The effect of temperature often leads to deformation of the gasket itself, which breaks the tightness of the system.

Incorrect torque when tightening cylinder head bolts

When assembling the engine, it is important to know the exact tightening torque of the bolts holding the head to the cylinder block. Increasing or decreasing this parameter can lead to destruction or deterioration of tightness, respectively.

In the second case, the cylinder head and cylinder head do not fit tightly to each other, which is why gases with atmospheric air pass into the existing holes and destroy the gasket.

To avoid such consequences, it is necessary to tighten the bolts using a dynamometer and strictly follow the manufacturer's instructions.

An equally important point is compliance with the screwing sequence. Detailed information on how to perform the work is given in the instructions for the car.

For example, the VAZ uses the following rules:

  1. First, the central bolts are screwed in, and then diagonally.
  2. The force is 3 kg*s, and then they reach 6 kg*s and 9-10 kg*s.

In 8 out of 10 cases, the cause of a broken gasket is non-compliance with the broaching rules in matters of torque, sequence and other nuances.

Therefore, be sure to read about the correct tightening of the cylinder head and with what force this should be done.

Low quality material

When purchasing pads, choose products from trusted stores.

Products come in the following types:

  1. Multilayer steel. Contain from two to five layers. The surface is treated with silicone for channel edging.
  2. Composite. Old technology that is almost never used. The base is asbestos and graphite, and the piston part is surrounded by steel rings.
  3. Copper. They are characterized by a high degree of reliability and are used on some types of cars.
  4. Elastomeric. Made of steel with a plastic material applied to the surface. There are steel rings at the gas joints, and the passages are edged with sealant.
  5. Non-asbestos. Manufactured using more modern materials.

The cost of a cylinder head gasket is not too high, so it is not recommended to save much on this, since such savings can be costly later.


Places where cylinder head gaskets burn out

Additional reasons

There are a number of additional factors why the gasket may burn out:

  1. Natural aging.
  2. Violation of the fuel combustion process. Most often, problems arise in the head, where cracks occur. The cylinder head, as a rule, has an aluminum base. When heated, rapid expansion occurs and the head presses on the gasket. The latter cannot withstand and is damaged.
  3. Increased temperature in the combustion chamber due to incorrect ignition angle, etc.

The car owner must understand the difference between a “breakdown” and a “burnout.” In the first case, there is serious damage to the gasket or its elements, and in the second, minor damage to integrity occurs, which sometimes cannot be found on the surface.

Actions for a broken cylinder head

Most drivers in such a situation wonder what will happen if they drive with such a gasket? Travel is not recommended except for a short distance. Otherwise there may be dire consequences.

After carrying out diagnostic measures confirming the breakdown of the element, it is better to replace it with a new product. It is advisable to also inspect other nearby surfaces. It is necessary to understand the cause of the burnout. Depending on the car model, the cost of the gasket will also depend.

If you want to replace the failed gasket yourself, first the head is cleaned of scale and the remnants of the old product are removed. Then you can inspect the surface. Armed with a ruler, you need to determine the presence of gaps, which should not exceed one millimeter. If the value is greater, you should grind the surface or install another one.

If you don't have a measuring device at hand, thick glass will do. You need to put it on top of the head, previously oiled. Next, inspect the surface for air spots.

One more point: when changing the gasket, it is recommended to apply graphite lubricant to its surface. This will give it more elasticity and softness. This way it will fit perfectly into place. Also, if it is removed, it is easier to get out. The advantage of using a graphite substance is the fact that during operation, graphite turns into ash.

How to check the cylinder head gasket

During the diagnostic process, the car owner must know how to check the head gasket for serviceability. To do this, use the following methods.

Using a glove, bag or balloon

Place a rubber glove, a bag (must be secured at the base), a condom or a balloon on the expansion tank, then start the engine and leave it for three to five minutes. It is advisable to increase the speed to three to five thousand. The more serious the damage, the faster the product fills with gases.

Use a bottle

On trucks to check, find a 0.5 liter bottle.

Next, do the following:

  1. Locate the breather on the expansion tank.
  2. Fill the bottle with water.
  3. Insert the tube into it.

The appearance of air bubbles indicates the presence of damage.

Diagnostic methods

When direct or indirect signs are detected, a new task arises for the car owner. He needs to figure out how to check the cylinder head gasket for a breakdown.

There are several methods in total. Moreover, the diagnostics are quite simple and can be used in garage conditions. Experience does not play a key role here, since even novice motorists can cope with the task.

If you are interested and need to know how to check whether the cylinder head gasket on a car engine has been broken, perform the following manipulations. Any of the presented methods is suitable for obtaining an accurate answer regarding the integrity and current condition of the seal between the block and the head.

  1. Visual inspection. The simplest option is how you can determine for yourself that the cylinder head gasket on the engine is broken or worn out. There is no specific and strict algorithm of actions here. The malfunction is determined simply by visual observation. First you need to start the engine, open the hood and take a closer look at the area where the block and head connect. If even a small amount of smoke comes out through the cracks, there is a problem. You can also listen to the behavior of the motor, which may begin to produce uncharacteristic ringing sounds.
  2. Checking the radiator and coolant expansion tank. It is also necessary to check the neck, with the help of which new engine oil is filled as part of scheduled maintenance. The method is also visual. Just unscrew all the caps and look at them carefully. Don't forget to look inside the tank. If coolant has penetrated into the engine, you will see a characteristic red emulsion on the oil filler cap. If the oil is in the antifreeze, then oily spots will appear on the radiator cap or expansion tank.
  3. Exhaust pipe monitoring. Start the engine. You can ask an assistant to rev the throttle a little to increase the volume of smoke coming out of the exhaust pipe. If you see white smoke coming out, which is actually steam, there is probably a problem with a broken gasket. When using antifreeze, white smoke with a characteristic sweet tint usually comes out of the pipe. Additionally, look into the coolant expansion tank. If the level gradually drops, then you have probably diagnosed a gasket failure. Although the sign is considered indirect.
  4. Checking the presence of exhaust in the cooling system. To do this, you can use one of 2 methods. The first method involves unscrewing the cap on the radiator or expansion tank. If there is active seething inside, this is a bad sign. The second method is to use a balloon or a regular condom. The product is pulled onto the neck of the tank, having first removed the lid. Then the engine starts at a speed of about 3-5 thousand per minute. If the balloon or condom inflates (quickly or slowly), a leak has occurred. This means that the gasket will need to be replaced in the near future.

Checking for microcracks

When checking the cylinder head gasket, it is important to pay attention to the presence of cracks. Several methods are used here.

Magnetic particle testing

The action algorithm is as follows:

  1. Place magnets on all sides of the head.
  2. Place metal shavings on top of the cylinder head.
  3. Pay attention to the "drawing". The chips will be drawn to the magnets, but they will remain in places of depressions and damage.

Using liquid

To check, do the following:

  1. Prepare the colored liquid using kerosene, acetone or another solvent.
  2. Apply the composition.
  3. Wait five to ten minutes.
  4. Remove excess liquid.

If there are defects, they are easy to notice even without a detailed inspection.

Pressure test

There are two ways used here - with or without immersion in water.

When immersed in water, do the following:

  1. Close all circuit channels.
  2. Place it in a container and pour in warm water.
  3. Apply compressed air to the area where bubbles appear.

Without dipping:

  1. Close the holes.
  2. Pour more liquid into the channel.
  3. Using a pump, pump in air to create a pressure of 0.7 MPa.
  4. Let the head sit for two to three hours. If the water leaks, we can talk about the need for repairs.

For repairs, a gas installation with additives is used with mandatory heating of problem areas to a temperature of 200 degrees Celsius or more. After completing the welding work, the seam is cleaned and pressed.

What to do if the cylinder head gasket breaks

If a malfunction is identified, the only way out is to replace the faulty element and determine the cause of the breakdown. The cost of the gasket varies depending on the brand of the machine and the quality of the product.

It is useless to repair the cylinder head gasket, because the work of a specialist will cost even more.

Other steps may be required:

  1. Replace the bolts if they become warped or if the manufacturer recommends installing new bolts each time the head is removed. If the bolt cannot be unscrewed due to bending, try tearing it off.
  2. Sand the cylinder head plane if it is bent. To do this, you need to contact specialists who use special machines. After removing the layer on the head, use a felt-tip pen to indicate the thickness of the removed metal, and you need to buy a gasket taking this thickness into account.

After eliminating the technical faults, you can begin installing a new gasket.

Follow these tips when doing this job:

  1. Clean the cylinder head from carbon deposits, scale or old gasket elements.
  2. Inspect the surface using a measuring ruler. It helps determine the presence and size of gaps. The latter should not exceed 0.5-1.0 mm. If this parameter is greater, the head requires grinding or replacement. If you don't have a ruler, use a thick sheet of glass that is 5mm thick. Place the product on the cylinder head and pay attention to the presence of interlayers. For greater accuracy, the surface can be lubricated with oil.
  3. Before replacing, treat the gasket with a graphite-based lubricant. This step makes the product softer and promotes better pressing to the surface. In the future, after such treatment, the product will be easier to remove. In addition, graphite is not squeezed out during use.

After completing the work, you should be interested in the stability of the engine. Pay attention to the signs of malfunction that were mentioned at the beginning of the article. At the same time, do not force the operation of the internal combustion engine. Give it a little load first so that the head gasket finds its position.

Please note that removing/installing the BC head is a labor-intensive process. It is necessary to discard many components, drain technical fluids, screw in bolts correctly, etc. If you lack experience, it is better to entrust the work to professionals.

By the way, some car owners complain about increased power consumption of the engine after replacing the gasket.

Reasons for gasket burnout

There are few reasons why a cylinder head gasket burns out, but with a new engine there is only one – overheating. Even a short time of engine operation at temperatures above normal can cause this malfunction. In this case, the gasket may burn out quite a bit, and inexperienced motorists will not notice the first symptoms that appear. With further operation, the burnout increases, and the symptoms become more pronounced. Due to the fact that many car owners turn to specialists not after overheating, but after some time of operation, when the malfunction becomes a clear fact, they do not connect the burnout of the gasket with the recent overheating and demand from motorists other explanations why the cylinder head gasket burned out.

If the volume of coolant is insufficient, you may not notice a slight overheating of the head, since the liquid, circulating in the system, manages to cool in the radiator, but does not have time to remove heat in the required amount. Instruments in a car show the temperature of the coolant, not the temperature of the engine parts. Thus, when operating a car with an insufficient level of antifreeze, you can burn the gasket without realizing that the cause was overheating.

Burnouts occur due to poor-quality gaskets, but this mostly applies to engines after repair. This happens extremely rarely on new cars. Even on repair engines, the cause of such a malfunction may be factors related to the quality of the repairs performed:

  • unsatisfactory condition of the mating surfaces (remains of the old gasket, shells or scratches on the surfaces are poorly cleaned, head deformation);
  • incorrect tightening torque of the cylinder head bolts;
  • the order of tightening the cylinder head bolts is incorrect;
  • the thickness of the gasket is incorrectly selected (on engines where they come in different sizes).

When filling the cooling system with liquid, it is important to remove all “air plugs”! Otherwise, you can “burn” the gasket the first time you start the engine.

Which cylinder head gasket is better: selection rules

When choosing a cylinder head gasket, you must focus on the following criteria: resistance to corrosion, high temperatures, pressure and service life. Above we looked at the types of such products. Now let's take a closer look at their features.

Metal

Cylinder head gaskets made of metal are very popular among car owners.

Their advantages:

  • increased strength;
  • load uniformity;
  • long service life;
  • the presence of sealing elements that protect against depressurization.

Metal products are recommended for use on machines with a turbine or equipped with forced motors.

Asbestos

Asbestos-based gaskets are in great demand among car owners.

Their advantages:

  1. High temperature resistance.
  2. Affordable price.
  3. Slight shrinkage.
  4. The presence of metal elements in places where it is necessary.

Of the minuses:

  1. Deterioration in quality with prolonged use.
  2. Sensitivity to vibrations and temperature changes.
  3. The health hazards of asbestos (more relevant for people involved in production).

Non-asbestos

This category includes products made from modern composite materials.

They have a number of advantages:

  1. Almost complete absence of shrinkage.
  2. Long service life.
  3. Elasticity, guaranteeing a good fit to the surface.
  4. High temperature resistance.
  5. No fear of pressure changes.
  6. Reinforcement of main areas with metal components.

It is important to take into account that the service life of the cylinder head gasket depends not so much on the material as on the correct installation. If you don’t hit the shrink spot, there will be problems even with the most expensive product, so this issue must be approached with all responsibility.

The main sign of improper installation is its rapid damage and the appearance of the signs that were mentioned at the beginning of the article.

On diesel engines, improper installation may result in knocking of the piston system due to the fact that the moving element touches the edge of the gasket.

Which cylinder head gasket to choose

If the engine specification specifies a metal gasket, then that is what should be used. It will be most reliable to use an original spare part, but if you experiment, then for the better.

Many manufacturers produce products of even higher quality, not being limited by the peculiarities of mass production of cars. Their brands are easy to find through online reviews.

Usually they are also factory suppliers, but the goods are supplied according to their own catalog numbers. A list of analogues is available in the catalogs of major suppliers.

Results

In conclusion, we note once again that if you identify signs of a broken cylinder head gasket, you must immediately go to a service station for replacement or do the work yourself.

It is important not just to replace the damaged element, but to find the cause of the malfunction. For example, if it is an overheating of the engine, you must first deal with the problem, and only then install a new cylinder head gasket.

When replacing, follow the manufacturer’s recommendations in terms of the sequence of actions and tightening torque, because if these rules are violated, the product will not last long. But in such matters, the right thing to do is to find a good specialist and entrust all the work to him.

Found a mistake or disagree with something? Write in the comments.

Which gasket material is better?

Gaskets made of different materials

When replacing a gasket, many car owners have a reasonable question: which gasket is better - metal or paronite? Each of these materials has its own advantages and disadvantages. At the same time, you need to understand that if the manufacturer recommends using gaskets made of a certain material, then you must adhere to these requirements.

As a rule, a metal gasket is stronger than its paronite counterpart. Therefore, it is advisable to install it on powerful turbocharged or forced engines. If you do not plan to tune the engine of your car, but simply operate it in a gentle mode, then the choice of material does not matter much to you. Accordingly, a paronite gasket is quite suitable. Moreover, this material is more flexible and is able to adhere more tightly to work surfaces.

Also, when choosing, it is necessary to take into account that the material from which the gasket is made does not have a primary impact on its service life. A much more important indicator is how the gasket was installed. The fact is that there are very thin walls between the individual groups of holes. Therefore, if the gasket is not installed exactly in the seat, then there is a high probability of burnout even in the strongest material.

The most obvious sign that the gasket was installed incorrectly is its rapid failure. Also, if you installed it incorrectly, the car may simply not start. In diesel engines, the knocking of the pistons may also be heard. This happens because the piston touches the edge of the gasket.

Conclusion

If you have a broken cylinder head gasket, then it is not advisable to drive a faulty car . Therefore, we recommend that if you discover a gasket break, replace it immediately. In addition, it is important not only to detect the very fact that it is broken, but also the reason for this. In particular, why the engine overheats or other malfunctions occur.

During the replacement process, monitor the torque on the mounting bolts. Timely replacement of the cylinder head gasket will save you from large financial expenses on repairing more expensive components. The longer you drive a car with a blown cylinder head gasket, the more likely it is that other, more expensive and important engine components will fail.

Rating
( 2 ratings, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]