Alarm Panther - key fob: instruction manual

How to attach a key fob to a Panther alarm? Disarm the car and sit in the driver's seat, turn on the ignition and press the Valet button three times. After a short signal, click on the button with a closed lock on the remote control being linked. A long beep indicates that the action is correct. To exit the mode, turn off the ignition or do nothing for 15 seconds. Below we will consider in detail how to proceed to connect, how many and which transmitters can be connected to the security system.

Alarm Features

The device with which control is carried out is a key fob.
It has five buttons with which you can give commands. Communication is two-way. To provide the necessary information, the key fob is equipped with a small liquid crystal display. In addition to the main key fob, the kit also includes an additional key fob with four buttons. The radius at which two-way communication is ensured is one thousand meters. If we talk about the distance at which an information signal can be transmitted, then we are talking about two thousand meters.

How many key fobs can be registered

Before programming the Pantera key fob, decide on the maximum possible number of transmitters. According to the rules, you can link no more than four remote controls. A maximum of two devices with five and the same with four buttons. In this case, the codes of previously linked key fobs are erased, and you will have to configure the Panther alarm remotes again. How to do this correctly is discussed in the instructions above.

Main functions

The Panther keychain has a number of important functions for car security, but the functionality is not limited to them. In order to specifically imagine the possibilities, we will tell you in more detail about its functionality.

• Hours provided. Of course, this won’t surprise anyone these days, but note that this function is complemented by the presence of an alarm clock and a countdown timer.
• The code provides protection against scanning and interception. As is known, modern technologies in some cases allow unauthorized access to the system, but in this case, dynamic modification of the program code is provided, which provides an increased level of protection in such situations.
• Arming function with the signal to the main key fob disabled. Protection against false alarms. On the one hand, this may somewhat reduce the degree of protection of the car in the event of an attempt to steal it. On the other hand, there are cases of accidental activation due to weather (heavy rain) or other similar influences on the vehicle. In any case, the driver can use this if he deems it necessary.
• Possibility of transferring a call from inside the car to the owner's key fob. This may be important in the case when there is a passenger left in the car and he wants to remind the driver of himself.
• Remote engine start. There are several different use cases here. There is a launch on command. Periodic start-up with shutdown is also provided. A regular time interval at which the engine is started can be specified. It is possible to start depending on temperature changes.
• Some other features.

Can any keychain be attached?

Many questions relate to choosing a suitable transmitter. Do not rush to configure the Panther alarm key fob until you determine its compatibility. To obtain information, you can contact the seller of security systems or the service station where installation is carried out.

It is best to bind a remote control that is fully compatible. Most often, such devices have a completely identical design or a slightly modified design. In this case, all functions will work correctly.

An alternative option is to register the Panther QX 270 alarm key fob or another model with partial compatibility. But keep in mind that in this case only the standard set of functions can work, for example, arming and disarming. Other options (including autorun) are not always available.

The worst thing is when the remote controls are not compatible with each other at all. In this case, it will not be possible to resolve the issue and attach the key fob to the Panther alarm system at all. To avoid such consequences, it is better to take fully compatible models.

Contents of delivery

This system consists of several parts. After purchase, they must be carefully installed. If the driver has some skills in working with such equipment, then he can carry out the installation without much difficulty. If this seems too difficult, then it makes sense to contact an appropriate specialist. Let us list the main devices that make up the Panther.

• Main electronic unit.
• A key fob with a display and five control buttons.
• Additional keychain. It does not have a display and only three control buttons.
• The shock sensor is two-level.
• Siren to give a loud sound signal.
• A relay that is designed to block the engine upon command from the security system.
• A special block with wires designed for installing a blocking relay.
• LED indicator, along with its own cable.
• Push-button switch for Valet operating mode. Sometimes you may wonder what this mode is for. The point here is to disable some protective functions when the driver needs it. This situation, for example, may arise during the process of washing a car.
• The delivery set includes a limit switch.
• Set of wires.
• Instructions.
• Package.

Please note that we are talking here about the standard delivery set. Possibility of expansion is provided.

As an example, we can talk about the possibility of installing GPS sensors. Such additions will increase the level of safety for the car.

Reviews

Vitaly, 37 years old, Samara. Pros Reliability, works flawlessly for more than a year, no problems with it. Cons The battery in the main key fob runs out very quickly.

Arthur, 31 years old, Omsk. It works and works, a solid B! It triggered falsely several times.

Konstantin, 47 years old, Sochi I agree with the above. I'm already tired of changing the batteries in the key fob, a little more than a month passes and problems immediately begin. There are few settings for the shock sensor - it works quite often, it is not clear why. There is one plus and this is functionality - you won’t find more for this money.

How the key fob works

Once upon a time, the very first models used static code. Due to the fact that it constantly retained its value, there was a high probability of hacking and, as a result, the ability to turn off the alarm if it was stolen. This level of security was clearly insufficient.

Later, the creators began to use much more secure dynamic code. The principle of its operation is that each time a command is issued by the key fob, the access codes of both the key fob and the entire security system change.

Since this approach uses a different code each time, the likelihood of hacking has sharply decreased. However, such a possibility still exists.

In modern models, the principle of operation of the key fob has been improved again. The dialog model of code modification is taken as a basis here. The point is that its formation occurs in three stages.

1. The key fob communicates with the security system.
2. Based on the received data, a special signal is sent to the key fob.
3. Taking into account the information received, the key fob makes changes in the security system codes.

This security system makes it almost impossible to hack the system's access codes.

Models with auto start

Now you can purchase modern car alarm systems with an autostart function:

1. SLK-775RS;
2. SLK-868RS;
3. SPX-2RS;
4. PR-2.

These models have a whole package of added options and are considered the most reliable in terms of signal encryption and code reading.

Model capabilities and modes

Alarm system SLK-775RS is the most simplified option. It cannot be connected to the vehicle's CAN bus.

Its set of functions includes:

• two-way communication;
• auto engine start;
• turbo timer;
• protection against signal interception;
• preventing scanning;
• disabling the alarm system in two stages.

But the SLK-868RS model is an option adapted to any type of gearbox. It has the function of integrating control of engine operation by speed and oil pressure. To protect the code from attempts to read it, it uses a dynamic channel encryption method and doubled frequency, which increases the range to 2 km and significantly reduces interference.

SPX-2RS protects against hacking and code-grabbing due to the simultaneous operation of two interactive and redundant communication channels.

Other features include:

• reprogramming of additional channels;
• connection to CAN bus and immobilizer;
• 7 security zones;
• two-way communication;
• Panic mode;
• driver call function;
• control via GPS and GSM;
• two-stage disabling of security.

Model PR-2 is the most modern version. By using modern interactive communication channels, it makes hacking by code grabbers unacceptable.

Its specifics include:

• quick response to pressing;
• independent security zones;
• operating distance up to 1.2 km.

User manual

In order for everything to work correctly, you need to carry out proper installation and programming. The attached instructions should serve as the basis for this. Let's talk about it briefly.

The first section of the document briefly lists the main functions. Then there is a list of functions that will need to be programmed. Here are some of them.

1. Automatic arming.
2. Locking the doors when arming.
3. Locking the doors when the ignition is turned on.
4. Unlocking doors in the same situation.
5. Immobilizer mode.
6. Protection against false alarms.
7. Restart the system automatically.
8. Thirty-second delay for turning on the security (we are talking about the fact that if you start the engine without turning off the protective mode, then after the specified time the siren will turn on).
9. And also some other functions.

The next section describes how to give certain commands using various presses on the key fob buttons.

• Unlocking or locking doors.
• Turning security on or off.
• Complete or partial shutdown of the shock sensor.
• Silent activation of the security system.
• Temporary cancellation of passive vehicle arming.
• Turn Panic mode on or off. We are talking here about the short-term inclusion of chaotic sound and light signals for a short period of time.

The following is a description of the operation of the LED sensor in various operating modes of the system. Talks about using the special Valet button.

The second part of the instructions contains a detailed description with explanations for each issue discussed.

The programmable functions are discussed in detail and how to configure them is described in detail.

The instructions end with a detailed description of the security system and its installation process.

Pantera SLK 10i pager does not work properly

At the most inopportune moment, the car alarm remote control refuses to work. The key fob does not work when the buttons are pressed; the car cannot be armed or disarmed. What are the reasons?

1. The remote control has fallen off. Re-program it into the system memory.
2. My battery is almost done. Change the battery.
3. The car is parked in a radio interference area. Move it to another place.
4. Low battery voltage. Recharge the battery or install another one.
5. Failure of the alarm control unit. Contact the specialists.

Find out how to link a Pandora DXL 3000 keychain.

What to do if a malfunction occurs

As with any technical device, malfunctions can sometimes occur. Let's consider several possible situations of this kind.

The range of the key fob is very important for the safety of the car. If it begins to rapidly decrease, then something needs to be done about it. In this case, the most likely cause is a dead battery. This is a possible, but not the only reason.

In order for the security system to recognize the key fob, it needs to “remember” about it, remember its data. To correct this, you need to carry out the procedure for initializing the key fob data, which is described in the operating instructions.

If the key fob stops working due to a discharged car battery, due to possible sudden exposure to an electromagnetic field or due to very low temperatures, then its operation may change unpredictably, first you need to make some attempts to correct this situation. To do this, it is necessary to carry out an emergency shutdown and, having driven some distance, check the operation of the system. Sometimes repeatedly pressing the key fob buttons can help.

If the malfunction continues to occur, then the next step is to disassemble the key fob. It needs to be unscrewed and checked for dust and dirt and for the integrity of the contacts. It is also possible for liquid to penetrate into the key fob. You need to clean it and check the health of the system.

If this kind of measures does not help, then it makes sense to contact a service workshop.

Why bind the remote control?

Knowing how to register a key fob for the Panther system with or without auto start, you can solve many difficulties in the operation of the device. A garter may be required in the following circumstances:

1. Internal malfunctions in the security system.
2. Mechanical damage to the remote control.
3. Inappropriate behavior of the Panther alarm.
4. The need to increase the number of working transmitters.
5. After resetting the settings.
6. Other situations related to a malfunction of the security device.

Knowing how to attach a key fob to a Panther, you can solve many difficulties in the operation of the security system. But be careful and strictly follow the manufacturer’s instructions described in the manual.

In the comments, tell us if you had to do this kind of work, what difficulties arose during the connection, and what steps allowed you to solve them.

Security system programming

In order to correctly configure the security functions of the system, you need to program some of its functions. When purchasing a Panther, there are preset parameters described in the operating instructions. Perhaps this will suit you. If not, you will need to enter programming mode. Let us briefly describe how this should be done.

• Initially, you need to turn off the security system and get into the car.
• Using the Valet button, additionally make sure that the security system is disabled.
• Enter your personal code to access programming mode. It is issued upon purchase of the system and can only be entered once.
• Start the car, turn off the ignition and press the Valet button as many times as the first digit of the security code. Try to meet the allotted time. If the code consists of several numbers, then you need to enter them too, not forgetting the need to adhere to a strict time schedule.
• After entering the program, you need to press the Valet button three times. After this, a beep should sound and the system indicator light should start flashing.
• After this, you need to turn on the ignition or do nothing for a while until a signal sounds (one short and one long beep). After this, the system will go into security mode.

Page 2

© Saturn Marketing Ltd.

Functions of the remote engine start system:

Fully compatible with both automatic and manual transmissions

Compatible with petrol and diesel engines

Possibility of extending engine operating time using a transmitter

ShortStop function: arming the system with the engine idling

Remotely activated automatic engine start function at low temperatures with selectable temperature value

Low battery auto start function (SLK-675RS only)

Specifications

Panther alarm, useful information, how to install.
Panther car alarm connection diagram Pantera alarm scheme Main technical parameters of the Panther 868 alarm:

• command transmission distance - up to 1000 m;
• the working radius of the communicator in signal reception mode is up to 2000 m;
• signal encoding type - BACS;
• number of security zones - 7;
• frequency range - 868 MHz;
• supply voltage - up to 15 V;
• operating temperature - up to +85°C.

Equipment

List of components included in the car alarm kit:

• main block;
• adjustable shock sensor;
• multi-tone siren;
• small-sized transceiver module;
• thermal sensor (for installation on the engine);
• control diode (blue);
• Valet switch;
• 5-button communicator;
• backup 4-key transmitter;
• a set of parts for installing components;
• set of wiring cords with Molex connectors;
• documentation and set of stickers.