Alarm system Mongoose with 3-button key fob (operating instructions)

Equipment

The classic Mongoose car alarm package includes the following products:

• main processor unit;
• siren;
• two-level shock sensors;
• a set of installation cables with connectors;
• main communicator with LCD display and feedback;
• auxiliary key fob without screen and two-way communication;
• LED element used to assess the state of the security system;
• service button for emergency shutdown of the Mongoose alarm;
• fasteners;
• limit switches installed on the hood and trunk;
• installation and operating instructions.

Some Mongoose alarm models are supplied with volume sensors that respond to intrusion into the cabin.

Alarm connection diagram

The device is installed in accordance with the algorithm:

1. installation of siren, sensors, receiver, control unit;
2. connection using wires;
3. connection to the main electrical elements - window regulators, locks, headlights, turning lights;
4. testing is in progress.

The connection diagram is clearly shown in Fig.

Installing an alarm on a VAZ 2110 (video):

Designation of icons on the keychain

Each device has its own control panel. Alarm Mongoose 600, for example, has 2 buttons (lock/unlock). They correspond to icons with an open and closed lock. They may have a different appearance - on and off signs.

Functions

The Mongoose alarm has the following functionality:

• silent activation of anti-theft mode;
• automatic entry of the system into protective mode;
• turning on the alarm mode (activated after receiving data from the shock sensor);
• signal coding that prevents hacking using modern technical means;
• intelligent prevention of false positives;
• automatic shutdown of faulty sensors;
• two-stage disarming of the system;
• storing trip data in non-volatile memory;
• control of the driver's seat, mirrors, climate control system (alarm system in some models);
• setting up central locking control;
• ability to connect an immobilizer, GSM module and other auxiliary devices;
• manual control of the functioning of the central lock;
• Restoring user settings after a power failure.

Self-installation of a security system

Installation of a Mongoose brand security alarm requires compliance with a certain sequence of actions:

• First of all, the siren, sensors, receiver and control unit are installed;
• all of the above elements are connected to each other using cables;
• they are connected to all important car mechanisms (window regulators, central locking, turn signals and headlights);
• The operation of the security system is tested.

How to install

The Mangust alarm installation process includes the following steps:

1. De-energization of the on-board network. To do this, remove the battery terminals.
2. Installation of the processor unit. The head unit containing the distribution relay is placed in a place inaccessible to criminals. Do not install the unit near sources of heat or moisture. Self-tapping screws or plastic ties are used to secure the element.
3. Installation of the antenna module. The device is placed in the highest part of the windshield. Do not allow the antenna unit to interact with metal parts of the body and power cables. It is not recommended to change the module design or lengthen the standard wire. This may reduce the range of the key fobs. Before installing the antenna, the surface is degreased. For fixation use double-sided tape included in the package.
4. Siren installation. The part must be placed in a place inconspicuous to criminals. It is traditional to install the siren in the engine compartment on the mudguards or engine shield. It is recommended to turn the horn down. The device should be protected from water and heat. If the siren has an autonomous power supply, you need to gain access to the lock, with which the device will be turned off.
5. Installation of limit switches. The parts are placed on the hood and trunk so that they do not get wet. Switches must not be installed near drainage structural elements. If moisture gets in, the operation of the controllers is disrupted.
6. Installing a shock sensor. The element is mounted in the middle part of the cabin, which ensures the greatest susceptibility to attempts to damage the vehicle. The device is placed on a metal surface and securely fixed with self-tapping screws. The stable position of the sensor ensures the lowest frequency of false alarms.

Connection diagram

The installation cables are connected in accordance with the pinout contained in the instructions. The power supply wires connecting the system components to the head unit are equipped with fuses of the appropriate rating. Cable connections must ensure reliable contact. It is recommended to wrap them with electrical tape. According to the connection diagram, the negative terminals of the harnesses are connected to the ground nuts located on the body.

Mongoose installation: car alarm installation, connection

Installing a Mongoose brand alarm is a very complex process that requires the car enthusiast to have certain skills and technical knowledge.

If the owner of a vehicle doubts his abilities, it is better for him to seek help from professionals.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

Those drivers who have the necessary tools at hand and are well familiar with the features of the Mongoose brand security systems can use the instructions and carry out installation without the involvement of third-party specialists.

Features of car alarms of this brand

Mongoose brand alarms differ from similar security systems in their simplicity of design, excellent performance characteristics and affordable cost.

It copes well with the tasks and reliably protects the car from illegal entry. Thanks to these qualities, the Mongoose alarm system continues to be very popular among vehicle owners.

Installing such a security system will prevent hacking of the hood, trunk and doors of the car.

Tools

To independently connect the Mongoose car alarm, vehicle owners need to prepare tools and consumables:

1. Wires (a car enthusiast may not have enough cables, which are included in the Mongoose alarm package).
2. Multimeter.
3. Socket and adjustable wrench.
4. Screwdriver (will be used when removing instrument panels).
5. Knife.
6. Double-sided tape (for fixing sensors).
7. Insulating tape.
8. Foam rubber.
9. Connection diagram (included in the Mongoose amg alarm package).

Preparation for installation

Before installation of the Mongoose car alarm begins, the vehicle owner must disconnect the power cable (negative) from the battery. Experts recommend dividing the upcoming amount of work into several stages:

• prepare the car interior and power unit for installation;
• install all elements of the Mongoose car alarm;
• reassemble all dismantled elements;
• configure the security system and test its operation;
• prepare the vehicle interior for further use.

When independently performing work on installing the Mongoose alarm system, the vehicle owner must dismantle the panels as efficiently as possible. This is done to gain access to the car alarm cable connection points. First of all, the dashboard is removed, after which the car radio and glove box are dismantled. At the next stage, the car enthusiast will have to remove:

• from the steering column trim panel;
• stove (air duct) lining;
• fuse box cover;
• panel located under the hood release handle, etc.

Recommendations from experts

Each owner of a vehicle who will independently install the Mongoose alarm system must use the connection diagram for this security system. During the work process, experts recommend adhering to the following recommendations:

1. Decide on the location of installation of sensors, antenna, radio receiver, control unit, siren and other elements of the Mongoose car alarm.
2. Neither moisture nor dirt should get into the installation location of the control unit and siren. This element should be kept away from heat sources.
3. To achieve maximum comfort, the radio receiver and antenna should be installed at the highest point.
4. All power circuits must be protected by fuses.
5. The location of the impact sensors should be as close as possible to the axis (longitudinal) of the vehicle.

Self-installation of a security system

Installation of a Mongoose brand security alarm requires compliance with a certain sequence of actions:

• First of all, the siren, sensors, receiver and control unit are installed;
• all of the above elements are connected to each other using cables;
• they are connected to all important car mechanisms (window regulators, central locking, turn signals and headlights);
• The operation of the security system is tested.

How to properly connect cables to the main mechanisms of the car

The table shows how the wires should be connected to the elements of the vehicle:

Unit name Cable color

Points to remember

Each owner of a vehicle must, before installation, carefully study the instructions that are being developed for a specific modification of the security system.

When laying cables, you must avoid all places that are exposed to moisture.

The wires must be secured using plastic clamps. To avoid kinks in the wiring, you need to use pass-through tubes made of rubber.

After the installation of the security system has been completed, you need to configure the sensors. The next step is to program the remote control key fob and the main operating parameters of the system.

Following the recommendations of specialists and instructions, car enthusiasts will independently install the Mongoose car alarm.

• Absolutely legal (Article 12.2);
• Hides from photo and video recording;
• Suitable for all cars;
• Works through the cigarette lighter connector;
• Does not cause interference to radios and cell phones.

Designation of buttons and symbols on the key fob

Depending on the model of the anti-theft system, key fobs may have different numbers of buttons.

With 2 buttons

Key fobs of this type are equipped with keys indicated by closed and open locks. Working with the device involves single or sequential clicks. In the latter case, the break between actions should be 1-2 seconds. Using the key fob you can activate and deactivate the following functions:

1. Security mode. A short press of button 1 with the engine off activates the anti-theft functions. To select a security mode with inactive sensors, use sequential pressure on keys 1 and 2.
2. Silent activation of the alarm. Sequentially press buttons 1 and 2, after which use button 2 again. The actions are performed with the engine not running.
3. Deactivation of security functions. When the ignition is turned off, press button 2. To turn it off without sound alerts, press keys 1, 2, 1 in succession.
4. Turning on the lock block. With the engine running, press button 1. Key 2 is used to deactivate the lock block.
5. Anti-robbery. The option is activated by long pressing button 1 with the engine running.
6. Alarm mode. To turn on, a control element, indicated by a closed lock, is used.
7. Search for a car. When the ignition is inactive, button 1 is held for 3 seconds.

With 3 buttons

The key fob with 3 buttons in the Mongoose alarm is equipped with a diode, under which there are 2 rows of control elements. The first one is different from the others in color. Operating a communicator with three buttons involves performing the following actions:

1. Enabling anti-theft mode. It is carried out by short pressing 1 key. The action is performed when the engine is inactive.
2. Activation of protective mode with disabled sensors. Pressing 1 button twice activates this function.
3. Silent arming. Keys 3 and 1 are pressed sequentially. The ignition must be turned off.
4. Switching to silent protective mode with inactive sensors. Press control 3 once, then briefly press key 1 2 times.
5. Activating protective mode with the power unit running. Hold down button 3 for 3 seconds, then briefly press button 1.
6. Silent activation of security. Press button 1 twice, then use control 3.
7. Disable the alarm signal. This is done by briefly pressing button 2.
8. Deactivation of the security mode. The alarm is turned off by briefly pressing button 2.
9. Unlocking the driver's door. Door unlocking is activated using the programming menu. After this, press button 2.
10. Silent disarming. You must press buttons 3 and 2 successively.
11. Turning on the lock block. After activating the ignition, briefly press key 1. To turn off the lock block, use key 2.
12. Activation of alarm mode. With the engine inactive, hold down button 1 for 3 seconds.
13. Activation of search mode. The function is triggered by pressing button 1 twice. Search can be used when the system is in security mode.
14. Opening the trunk. Activated by pressing control 3 twice. Older Mangus car alarm models do not have this feature.

With 4 buttons

The system is controlled by activating the following functions:

1. Activation of security. When the ignition is not working, briefly press button 1.
2. Enabling protective mode with deactivated sensors. To do this, press button 1 2 times. The intervals between actions should be no more than 3 seconds.
3. Silent switching to security mode. When the engine is inactive, press keys 3 and 1.
4. Turning on the security mode with a working power device. After using 3 buttons, press key 1 2 times.
5. Deactivation of the anti-theft mode. This is done by briefly pressing control element 2.
6. Silent deactivation of protective mode. Press keys 2 and 3 successively.
7. Opening the trunk. When an additional channel is connected, press button 4 twice.
8. Turning on the turbo timer. When the ignition is active, use key 4 2 times.

With 5 buttons

The purpose of the controls is similar to those of four-button models. 5 button is used to activate vibration alert, change the type of sound signal and turn on the backlight.

Types and models

Now we invite you to familiarize yourself with the models and types of anti-theft installations of Mongoose.

Below are the systems that have gained the most popularity among consumers:

• AMG line, models 700, 700 plus, 700 Super plus, 750, 770, 800B, 800C, 800S/M, 850C;
• DX 1zone;
• ADD On;
• Base line, models 20, 30, 40, 50, 100, 200, 275, 300, 400, 475;
• Digital 100;
• Duplex line, models 2.1, 2.2, 3D;
• The EMS line includes models 1.7, 1.9, 7.0;
• Imperium line, models 5000, 7000;
• Cyborg;
• Matrix;
• Next;
• QS;
• QS Lux;
• RKT line, models 07S, 09S, 11S;
• TT-1 and TT-2;
• Two Way;
• Immobilizer.

Key fob programming

Programming of communicators in alarm systems Mongoose 750 and 770 is carried out as follows:

1. The system is disarmed, after which the key is turned in the ignition switch.
2. The password is entered. After dialing the first number, the engine is turned off. To enter 2 digits, repeat the steps with the ignition. When using an unambiguous code, proceed to the next step.
3. The key fob data is entered into memory. After 2 beeps appear, press key 1 of the key fob. After the beep appears, they proceed to binding the auxiliary communicator.
4. The emergency button is pressed. The programming mode is deactivated after 15 seconds of inactivity.

To bind the control panel to Mongoose 700 and 800 you need to perform the following steps:

1. Turn on the ignition and press the emergency button 5 times.
2. After a long beep, press any button on the key fob to be attached. The entry of the device into the head unit’s memory is confirmed by a short beep.
3. Perform the above steps for key fob 2.
4. Turn off the engine and wait 10 seconds. Exiting the programming menu is accompanied by a long beep.

Linking key fobs in Boomerang Premier is done as follows:

• after turning on the ignition, press the service button 5 times;
• after the sound signal, keys 1 and 2 of the linked key fob are used sequentially (data entry is confirmed by a beep);
• The above steps are performed for the additional remote control.

Pros and cons of the anti-theft system

First, let's look at the advantages of an anti-theft installation:

• as reviews show, Mongoose alarms allow you to easily cope with the tasks assigned to them, regardless of the ambient temperature;
• most models have extensive functionality that allows you to ensure reliable protection of the vehicle from burglary;
• in most cases, all components, from the remote control to the central unit, function flawlessly;
• affordable price for most buyers.

Now, briefly about the shortcomings that can occur in the operation of a car alarm:

• malfunctions may occur in the operation of the anti-theft system, we wrote about them above;
• the procedure for installing a car alarm is a rather complex task, the implementation of which is best left to professionals;
• One of the “diseases” of Mongoose alarms is considered to be the failure of the control panel.

Setting up autorun

Activating autorun can be done in several ways:

1. From the keychain. To do this, briefly press the M and 1 buttons. The corresponding indicator will appear on the screen. The duration of the motor operation is set in the programming menu.
2. By time. The setup begins by simultaneously pressing the M and S keys located on the side of the remote control. After this, an indicator appears showing the time. Change the value using buttons 1 and 2. Use button 3 to confirm the selection of the parameter. A sound signal notifies you that the procedure was performed correctly.
3. By temperature. Use the M and S keys to enter the programming menu. The warm-up time is selected by pressing buttons 1 and 2. After that, hold down the M key for 3 seconds.

How to turn off the alarm

To disable Mongoose 400 Base, you need to open the car with the key and start the alarm mode. In the next 7 seconds, perform the procedure of turning the engine on and off three times. After the blinking starts, the number of flashes will be counted. After reaching the value corresponding to the code, the ignition is turned off. To disarm the Mongoose 600 after starting the alarm mode, press the service button 6 times. The system is completely deactivated.

Mongoose 700, 800 and 900 are switched off by pressing the emergency button once. Mongoose B001 is protected by a complex code, so after opening the door you need to start and turn off the engine 4 times. The first number of the code is entered by deactivating and activating the ignition. The remaining numbers are entered in the same way. Mongoose 750 or 770 also turns off.

• Install an alarm with auto start
• Alarm Red Scorpio
• Connecting autostart to the ignition switch
• DIY rear view camera washer