The standard radio of the 2nd generation Kalina or Lada Granta is significantly different from the head units (GU) of previous cars. The large touch screen makes it look like a foreign car radio, however, its functionality is poor. But you can expand the capabilities of the radio with a simple operation. |
Direct firmware mms 2190 grant
The firmware process is quite simple! All you need is an SD card. Note! The SD card must be formatted in FAT16. A common problem after flashing the firmware is the Lada logo freezing on the monitor of the standard multimedia system. This problem may occur as a result of:
• Failure to comply with the parameters of the required formatting system; • Old SD card model, different from SDHC.
If a problem of this kind arises, then it is necessary to check compliance with the above two points of the procedure for flashing multimedia firmware on the Lada Granta.
After the flash drive is formatted and the new software has been decided, for example, NewMenu V7.391Nitro, you need to download the new firmware NewMenu V7.391Nitro and unpack it directly onto the SD card itself.
As for the FirmWare folder, the files located in it must be moved to the root of the SD card. The root of the SD card implies placement of files in addition to other moved folders.
The copying process is complete, which means it’s time to remove the flash drive from the computer. It is worth noting the need for mandatory safe removal, which has long been known to all PC users.
An SD card with files placed on it must be inserted into the mms. After the removable media is inserted into the mms, it must be turned on. After waiting for the device to fully boot, long pressing the volume key will reboot it.
The reboot takes place in four stages, which is shown in the example of four boot lines, upon completion of which, MMS will start in normal mode (standard display menu). Just a few seconds after the standard menu, the radio will go to the altmenu.
Note! If any device is connected to the USB radio, the altmenu will not start. After removing the device, the radio must be rebooted again.
The advantage of using the ATH-08 DNS USB splitter, which was mentioned at the beginning of the article, is multi-polarity. A GPS receiver and other USB devices connected to the hub will not interfere with the launch of the altmenu, but will become inactive.
How to update the radio firmware to ver.38 (23.0.2.38)
Archive password: club-lada.rf
Features of the assembly with the altmenu:
- The build is based on version 23.02.38.
- Has built-in Russian localization.
- Launching the altmenu without rebooting from the standard menu (by long pressing “Settings”).
- Built-in driver for GPS receiver BU-353s4.
- Initialize sound and time without the participation of the MMC.exe process.
- Display of engine temperature and remaining fuel (provided the CAN bus is entered into the MMC).
- Screen and sound settings.
- There is a radio.
- Support for radio buttons.
Firmware: Unpack the contents of the archive to the root of the SD card:
Next we proceed as described above. This assembly can work without an SD card, or you can delete the Install and Firmware_v38 folders. The Navigation folder must be present on SD or USB, it was created for navigation programs, for example, for Navitel you need to put Navitel in this folder. Now all that remains is to install the navigation program, configure the GPS and GSM modem. In the comments, share your reviews of the firmware and links to them. By the way, do you know how to play most video formats on the standard radio?
How is the firmware for MMC 2190 performed on a Lada Granta?
How is the firmware installed for the MMC 2190 Grant? This question is asked by many car enthusiasts. Lada Granta is a modern domestically produced car; it differs significantly from previous models offered to VAZ car owners. This is a reliable car that belongs to the budget class. The interior equipment deserves attention. Unlike previous VAZ models, the Lada Granta Lux is equipped with a multimedia system that is not inferior to foreign cars. There are several models of MMC Lada, so you can purchase the most suitable option. The multimedia system is equipped with TouchScreen. Much attention should be paid to catalog numbers. The Lada Granta MMC runs under the Windows CE 6 operating system, which is designed for devices that have maximum memory. But the operation of a multimedia system is not always ideal. In this case, the firmware for MMC 2190 Grant will eliminate some problems.
Main functions and appearance features
The infotainment display is very bright and the touchscreen is sensitive to touch.
Multimedia supports three formats. It provides the opportunity to listen to audio, see the cover and artist name. You can adjust the sound quality using the equalizer. MMC Lada Granta has about six programs that perfectly optimize sound quality. Of course, such settings do not allow you to achieve ideal quality, but the music will sound clear and without interference.
MMC 2109 has the ability to view video files
Not all video formats can be viewed using multimedia. For this MMS, only WMV format is available. Therefore, you can only record video files using a converter. Higher file resolution will cause the system to freeze. The processor used in the multimedia system is quite weak. Viewing photos is a little difficult. The better the quality of the photo, the longer it takes to open.
The standard version of the MMC Lada Granta Lux allows you to use the Bluetooth installed in your mobile phone and listen to the recordings that are on it. The multimedia system can “read” flash drives, but their maximum capacity should be no more than 64 GB, as well as SD cards up to 32 GB.
Easy link mms 2190
Download:
Description:
Alternative menu (shell) for MMC cars Lada Granta, Kalina, Priora. In NewMenu 9, all functionality is divided into separate applications. The main applications - radio, video player, audio player, BT player, AUX, phone and navigation - are located on the main menu screen. The remaining additional functions of MMC are divided into corresponding applications. For example, application options: Trip computer, Car (displaying a car with doors, indicators, etc.), Climate (for displaying climate status), Motor (for reading and decoding errors, controlling fans), an application for measuring dynamics, an application for street racers (red flash), etc.. You can come up with many applications. Applications can be uninstalled and installed through the Application Manager. Those. You can create your own MMS functionality. Installed applications are displayed and launched in the Applications window. Some applications can be launched as a screensaver (Trip Computer application). Applications can be launched either by a hot button (the Trip Computer is launched by clicking on the Fuel icon in the Kan-panel) or by an event (for example, when check the Motor application is launched).
Possibilities:
- Listening to radio, audio files; watching videos.
- Connection with phone via Bluetooth protocol; Speakerphone; the ability to receive and make calls; phone book with quick contact search; listening to music from your phone via Bluetooth (via BTPlayer).
- Launch a navigation program, simultaneous use with all audio applications.
- Playing navigation prompts when listening to the radio, AUX, music from the phone, during a telephone conversation on the front or rear speakers (mixing).
- AUX input support (hardware modification required).
- Sound settings (balance, equalizer, advanced hardware equalizer settings); screen settings, automatic day/night mode switching; turning on the parking camera.
- Setting up sound alerts, mixing direction and volume, and the ability to immediately do a mixing test.
- Kan-panel with vehicle data readings, voice prompts about the vehicle’s condition.
- Automatic volume adjustment depending on the current speed (auto volume).
- Support for navigation programs, support for USB GPS receivers, support for standard GPS receiver.
- Trip computer application: display of trip data (speed, revolutions, gear, mileage, time, consumption, cost, remaining range, etc.), recording trip data in the log, log viewer with data grouping, adjusting the accuracy of mileage and fuel level in the tank, and etc.
- Motor application: reading, displaying, decoding engine errors, resetting ABS automatic transmission SRS errors, manual and automatic control of engine fans, idle speed control when the car is stationary.
- Other applications: file manager, text viewers, calculator, browser and many others.
- Switch between all running applications using the Mode (Menu) button.
- Ability to change the design style, preview the changes made.
- All main menu settings in one window with tabs.
- Saving all user settings (including design) when switching to a new version.
- Steering column switch support.
Installation, update, removal, disaster recovery:
Installation
1. Unpack the archive into the root of a USB flash drive or SD card (Install folder). 2. Exit to the MMS desktop. Run the file InstallInstall.exe (white label) from a USB flash drive (SD card). When installing on a clean MMC, there will be a reboot, then the installation will continue. 3. To install the MMC to the internal memory, click Install. To install to an SD card, click Cancel, then click Install. 4. Select drivers for the USB devices you are using and click Install. If there is nothing, click Cancel. 5. Select the MMC type. 2190 – MMS standard installed on Granta, 2192 – MMS standard installed on Kalina/Priora. For MMC with standard navigation, select the type with navigation.
Section 1. MMC management console
The Microsoft Management Console is the primary administrative tool in Windows Server 2003. The Microsoft Management Console provides a standard interface for one or more applications, called snap-ins, that you use to configure elements of your environment. These snap-ins are tailored to solve specific problems and can be organized and grouped within the MMC console according to your preferences.
For example, the pre-configured Active Directory Users and Computers console is designed specifically for administering security principals (users, groups, and computers) in a domain. Consoles within the MMS (but not the MMS itself) are the administration tools you use.
MMC console
The MMC control console is similar to Windows Explorer, only with fewer buttons. The functional components of an MMC are contained in so-called snap-ins: the menu and toolbar provide commands for managing parent and child windows, and the console itself (consisting of snap-ins) defines the required functionality. In addition, depending on the situation, the MMC console can be saved with different parameters and in different modes.
Note MMC consoles run under Windows Server 2003, Windows 2000/NT 4/XP/98.
Navigation in the MMS console
An empty MMC management console is shown in Fig. 2-1. Notice that it is given a name and has a Console Root . It is in this root of the console that all the necessary equipment will be placed.
Rice. 2-1. Empty MMS console
Each console has a tree (shown on the left), menus and toolbars, and a detail pane (shown on the right). The contents of these elements depend on the purpose and functionality of the console you are using. In Fig. Figure 2-2 shows the MMC console with two snap-ins loaded, as well as a child window of the Device Manager snap-in.
Working with the menu and toolbar of the MMC console
Although each snap-in adds its own unique menu and toolbar elements, there are a few key menus and commands that are used in many situations and are common to most snap-ins (Table 2-1).
Rice. 2-2. Filled MMS console
Table 2-1. Typical MMC console menus and commands
How to set up "GPS" on the firmware version of the multimedia?
Carrying out this action will not take much effort. The procedure involves preliminary switching with the GPS module and consists of the following algorithm of actions:
- go to the corresponding “Tools” menu;
- activating the display keyboard;
- direct module switching;
- route instructions: “staticstoredll232usb.dll”;
- continuously pressing the “OK” key after the prompt regarding driver selection is displayed on the screen.
TV standard
How to flash a car radio
Frequent requests from a Russian driver who wants to reflash his Japanese or Korean car radio are also related to a TV monitor. It cannot be used for its intended purpose, since it does not support the standard of our Secam television.
Due to some features of television broadcasting, it may also be impossible to watch high-quality television programs while driving. To ensure traffic safety, some cars use a lock that turns off the image on the monitor while driving.
How to reflash a car radio
To improve the TV systems of car radios from Japan (reflash the software, change the standard, remove locks), it is customary to use special adapters. They can be installed in any car.
Flashing car radios
Descriptions of media control options
Before you begin the step-by-step manipulations of retrofitting the MMC, you should familiarize yourself with the descriptions of the multimedia control options.
Important! The use of multimedia is permitted only if it is guaranteed that there is no threat to traffic safety due to the possible loss of control of the road situation by the driver.
So, the Niva Travel multimedia system consists of a control unit, as well as a resistive and touch screen (see photo)
Control block option symbols
The control unit consists of:
- Encoder washers (with PWR on/off and MUTE volume control functions).
- Radio switch.
- Multimedia power buttons.
- Home Main Menu Options.
- Navigation system switch
- Enable Bluetooth mode.
- Encoder for file transitions, settings for FM radio stations - TUNE, as well as turning off the display - D OFF.
- Microphone.
- Card slots.
- RESET button (covered in the photo) to restart the multimedia.
- Sockets (also under the cover) for USB connection.
As for managing options, all manipulations, both with encoders and buttons, are intuitive. Except, perhaps, for two important features. Namely, if you turn off the ignition while the multimedia is running, this system will not automatically turn off. Therefore, in order not to discharge the battery during idle time, you should also turn off the multimedia using encoder washer 1.
And the second feature of the control unit is that it is prone to freezing. The RESET button is intended to reboot the system.
Important! Before you start rebooting the system, you need to remove the memory card from the slot located under the cover (not shown in the photo) to avoid damage to the system program files.
Home or Main Menu
When you press the Home button on the touchscreen, intuitive icons will again appear. When you touch the corresponding icons, certain sections necessary for the driver will appear.
How to eliminate some shortcomings of the multimedia system
Sometimes, in order to start using new media, you need to purchase it. She will certainly be able to cope with tasks that are standard. But you can’t expect more from it without additional modifications. Without this, you will not be able to configure the navigator or connect a rear view camera.
It must be said that many multimedia that modern foreign cars are equipped with are significantly inferior in their capabilities to the MMC Grant. This system is unique and quite competitive. If there are minor problems in the operation of the MMC, then updating the MMC firmware will eliminate them. Let's look at how to make firmware for 2014.
Possible even from abroad
You can call the Unified Message Processing Center free of charge from anywhere in Russia at the number: 8−800−200−40−40. From abroad you can call: +7−499−550−40−40, +7−495−539−40−40.
Questions in the form of SMS and MMS messages are accepted to the number 0−40−40 only from the phones of Russian telecom operators. Sending a message is free. It will be possible only in Russian and no more than 70 characters.
The Direct Line program was first released in 2001. Then the president was asked about 400 thousand questions. The live broadcast asked 47.
There is an analogue of the direct line for children - the program “Non-Childish Conversation with Vladimir Putin.” In it, the head of state answers questions from gifted schoolchildren.
- People
- Putin Vladimir Vladimirovich
- Die Zeit published Putin's article “Be open despite the past”
- Putin called for uniting in order to increase incomes by 2026, and have time to get vaccinated before then
- The armor is strong: the media compared Biden’s “Beast” and Putin’s Aurus
- Plot: “Direct Line” with Vladimir Putin
This bookmark is intended for those more attentive of you who notice typos, spelling, punctuation and factual errors in our texts and would like to help us correct them. We thank in advance everyone who works with us to improve the quality of our materials. Your help is invaluable not only for the editors - it is also important for those readers who, thanks to you, will read these texts in the correct edition.
To tell us about a typo, select it with the mouse and press Ctrl+Enter
Are you interested in how to connect MMS to MTS without entering settings? The operator has a free one. When connected, special equipment sends your messages regardless of whether you have set up your own phone or not. To connect, dial *1112156#, or send an SMS to number 111 (text – 2156).
In addition, you can activate in your personal account if you have an Internet connection. The entrance to your personal account is located at this link - online.mts.ru.
How to remove the BC or MMS screen (monitor) on the Lada Priora
April 22, 2022 Lada.Online 22 109
On the new Priora, the on-board computer (BC) or the multimedia system screen (MMS) is placed on the panel (dashboard) in a specially designated place. During vehicle operation, it may be necessary to remove these devices (for example, to replace or install sound insulation). More on how to do this below.
The upper visor is attached to the panel using clamps (clips). To remove the visor you will need:
- pull its right side up (if necessary, pry it up with a flat screwdriver or plastic spatula);
- pull towards you, unlatching the rear latches;
- Unscrew the two screws securing the MMC or BC monitor (depending on the configuration). Lift the device up.
New Lada: Coolant temperature sensor Priora 16 valves
Assembly is carried out in reverse order. The dismantling process is also shown in the video:
If you need to further remove the center console, follow these instructions. Let us remind you that the windshield and body wings were less dirty; it is recommended to install aerodynamic flaps in the wheel arches.
Keywords: instrument panel Lada Priora | cassette player Lada Priora | on-board computer Lada Priora | Lada Priora torpedo
3
1
Found an error? Select it and press Ctrl Enter..
- AvtoVAZ offers discounts on LADA purchases for SDEK
- Which cabin filter is better to choose for Lada Vesta, XRAY
- The body colors of the Lada Granta Drive Active have become known
- We clean the drainage holes and lubricate the body fittings on the LADA
How to install 2 din in grant norm or standard
Everything is more complicated here. Need to:
- dismantle the center console trim - unclip the fastenings, move it forward and disconnect the buttons and heater handles;
- cut out a vertical plastic partition that will not allow you to install a 2 din device;
- file the plastic casing of the central air duct;
- try on a new acoustic unit, adjust the fastenings if necessary;
- install adapters from the delivery kit on the wiring (if required);
- install the device;
- if we leave the old center console trim: we cut out the partition, try it on, put it in place with the buttons and handles connected, adjust the decorative frame of the control unit, install it;
- if we install a new trim on the console under a 2 din device: we transfer the heater control unit and buttons from the old trim, install them in place, and put a decorative frame on the control unit.
Video instructions for flashing firmware for Lada head unit
If after the firmware the radio does not boot, but freezes on the “LADA” logo :
- Make sure nothing is inserted into the USB port.
- Create an empty Explorer.txt file in the USB root. After rebooting, the WinCE desktop should load.
- Try turning off the power to the MMC (remove the battery terminal) for 5 minutes.
- Try formatting the SD card to a different file system (FAT32/exFAT/FAT) and reflash the radio again.
- Use another SD card to flash the radio firmware.
Let us remind you that we solve other problems of MMS related to its operation in this article.
Description of types of firmware.
Versions 1.7 and 1.13 are stock. The navigation built into the car only works on 1.13, 1.23 and 1.24.
1.9, 1.10, 1.11 are based on 1.7; 1.23 is based on 1.13. In 1.7 there are only 11 IDs that can be forwarded to the COM port, no dividers, etc. no, and adding them is very difficult. In 1.13 there is an ID group (3 pieces 481, 551, 280) with dividers, an ID group without dividers (4Ax) and an ID group (8 pieces) without dividers disabled in the firmware. Also, information from some IDs is taken and processed inside the CAN controller. However, I don’t know how to get it. In 1.24 (modified 1.23) it was possible to receive IDs with a mask, that is, select the range of received IDs. I did this with the 7E8..7EF range to receive diagnostic requests from all controllers in our cars. ID 4A2 only for combinations with built-in GPS and only with a connected 6-button steering column switch.
Each version has its own pros and cons: Versions based on 1.7: + Reflashes well even with the engine running. — Data transmission is choked (if you often send data to the CAN controller, it stops being sent to the bus). — Not enough ID. Versions based on 1.13: + Data transfer does not choke. + Lots of IDs. + There are dividers (it really helps reduce the load, because ID: 180 messages are sent 100 times per second) - Flashing is very sensitive to bus activity, etc. (there have been cases of corruption).
How can you modify the MMC Lada Granta Liftback
To maximize the functionality of the MMS menu, we reflash the data. The process is not at all complicated; we strictly follow the recommendations of the experts.
- Flash card with a capacity of at least 4GB;
- Laptop (tablet);
- USB cable in case the system freezes.
Sequence of actions for independent firmware MMSlada Granta Liftback:
- We insert the SD card into the laptop, format it into the “FAT” file system;
- We write the modification of the firmware file to the root of the card. It is not recommended to copy the firmware to other directories, since the data is not counted when loading by the operating system;
Insert the SD card into the MMC
Note for the driver. The stock firmware is indicated by the index 2.2.2.11. A complete list of official firmware is posted on the official Lada website. Custom firmware is not always installed correctly, and sometimes the system freezes. All actions related to custom firmware are under the personal responsibility of the owner.
- After copying the firmware to the SD card, check for the presence of the following files: chain.bin, chain.lst, NK.bin, TINYNK.bin;
- We insert the SD card into the connector on the standard radio and check that there are no third-party gadgets connected to the USB connector. Restart the radio;
- During the first 20 seconds we observe the process of copying files, after which the screensaver starts - the Lada logo;
- The main menu appears, which will display the following sections:
- Navigation;
- Media;
- Office: reader, PDF reader, notepad, calculator, on-screen keyboard;
- Internet;
- Tools;
- Rear View Camera;
- Exit.
( 1 rating, average 5 out of 5 )
Work order
The process itself is very simple. To use such a card, you must first format it in FAT16. During the flashing procedure, the Lada logo may freeze, this happens for the following reasons:
- Outdated map;
- The card was formatted in the wrong system as required.
Therefore, the procedure is simple, but it must be treated very carefully. You can download the new firmware on the official Lada website.
We connect the card to the multimedia system. Then we turn on the standard system itself. We wait for the system to start and then reboot the radio by pressing the volume key.
The program must go through four stages. Once enabled, you will see an alternative menu. This ends the preparatory stage. If everything is correct, you will see working Windows. Then all that remains is to install the software. Go to the folders Start – Setting – Control Panel.
If you experience freezing when moving from folder to folder, then simply reboot the system. Going to the panel, open the Stylus – Calibration icon. This menu will help you calibrate your screen.
Next, reboot the system again, press the volume key and hold for about ten seconds.
After turning it on again, open the Soft – radio folder and run the installation file.
These actions will help the system recognize files and stabilize the operation of your media system, as well as adjust the equalizer when you listen to the radio.
Then we set up a navigator if you need one. Go to the tools, connect the module, specify the path Staticstoredll2usb.dll. After finishing the search, press OK, and continue to press until the menu disappears from the display.
Method No. 1
You will need : a USB-GPS receiver (for example, BU-353S4 or 0183 NMEA, see the AliExpress catalog), a driver for this device and a navigation program (for example, Navitel). It is not necessary to flash MMS.
The GPS receiver is connected to the USB connector of the MMC. You can place the GPS antenna in the glove compartment, or under the panel on an iron stand, using the receiver magnet.
Other features and firmware
Tampering with car radio
In addition, there are a number of manipulations that help improve the devices. Often these interventions are also called flashing and they are aimed at improving the capabilities of the device. Below is a table showing these manipulations.
Remaking car radios | D864 is unsoldered (if Toshiba) |
Decoding | The code (9507) is dialed and then BAND |
If the laser loses sensitivity and is unstable | The variable resistor RV14 is soldered |
Stereo reception has deteriorated, the mechanics fail, there is no sound | The electrolytes in the red shells on the board are removed, the space under them is washed, and then new electrolytes are sealed in |
If you need to change the range from Asian to European | Diode D701 is unsoldered. Resistor R752 is changed to 2.2K. After this, the voltage is set on FM VT |
If you hear a gurgling sound in one or even more channels | Electrolytes near the amplifier are to blame. They began to flow because the paths underneath them collapsed. |
The quality of playback of recordings from a cassette decreases. The sound is getting quieter, but the radio is coming through normally | Electrolytes are replaced with conventional small-sized ones |
The changer does not accept the disc and only works to eject | LED emissions are reduced. Typically, the limiting resistor is halved |
FM receiver does not pick up even-numbered stations | A 2Kohm resistor is placed on R824 and the capacitor is discharged to power the car radio |
4 linear outputs of the amplifier fail, but the subwoofer continues to work (trouble often happens on standard Toyota car radios) | The electrolytes in the red shells change again |
The car radio does not pick up the FM range or does so only after warming up | The reason lies in the communication coil |
Some buttons do not work when you need to enter a code | The firmware is changed, the code is installed. If that doesn’t help, look for the oxide under the buttons |
Receiver frequency tuning | Switch the broadcast network or change the local oscillator frequency in the tuner |
Transferring the car radio to European mode | Solder in diode D2 instead of D1, which is located closest to the processor on the board |
Flashing Japanese car radios
Electrics, sensors, battery Lada Vesta
Products from the Dustershop77 range on the topic of the article:
Name | Manufacturer | Price | Availability | Add to cart |
DC1134-7700427640 | Door limit switch (switch) original 7700427640 | Original | 800 / 500 rub. Discount: 400 rub. | 4 |
DC954-8200719629 | Manifold absolute pressure sensor MAP sensor for 2.0 and 1.6 engines - F4R/K4M original 8200719629 | Original | 2500 / 1900 rub. Discount: 1700 rub. | 1 |
DC1195 | Fuse set 180pcs in a plastic box | China | 1000 / 700 rub. Discount: 600 rub. | 1 |
DC990-8200060049 | Seat heating switch original 8200060049 | Original | 800 / 700 rub. Discount: 600 rub. | 3 |
DC485-497612479R | Power steering fluid pressure sensor original Renault 497612479R | Original | 1800 / 1400 rub. Discount: 1200 rub. | 1 |
DC997-255678753R | Steering column switch right article number 255678753R | Original | 2800 / 2700 rub. Discount: 2700 rub. | 1 |
DC1143 | Renault mirror control button (joystick) | Original | 700 / 500 rub. Discount: 450 rub. | 5 |
DC1027-8201167988 | Left steering column switch with PTF article number 8201167988 / 255400337R | Original | 6000 / 4700 rub. Discount: 4000 rub. | 1 |
DC1360-7711238598 | Rechargeable battery original Renault 7711238598 | Original | 15000 / 12000 rub. Discount: 10500 rub. | 1 |
DC1754-104035756 | Door limit switch Lada Vesta HANS PRIES TOPRAN (1 piece) 104035756 | Analogue | 300 / 200 rub. Discount: 100 rub. | 4 |
DC1404 | Trunk lid and door lock activator (Asam/MANOVER analogue 7700712901) | Analogue | 1400 / 900 rub. Discount: 700 rub. | 1 |
DC1828-35372203 | Pin fuse 15A 35.3722-03 (1 pc.) | Original | 10 / 7 r. Discount: 5 rub. | 3 |
DC634-601986892R | Speed sensor (plug) for cars with ABS original 601986892R | Original | 1900 / 1650 rub. Discount: 1450 rub. | 1 |
DC996-255675128R | Steering column switch left article number 255675128R | Original | 4700 / 4300 rub. Discount: 3800 rub. | 2 |
DC1520 | Solenoid relay 1.6 H4M | Analogue | 1900 / 1600 rub. Discount: 1400 rub. | 1 |
DC1793 | Ignition coil connector Duster, Terrano, Captur | Original | 600 / 500 rub. Discount: 450 rub. | 1 |
DC1812-6001547488 | Heater resistor Duster, Logan, Terrano, Sandero, Kaptur, etc. original 6001547488 | Original | 1500 / 1000 rub. Discount: 800 rub. | 1 |
DC623-8200547283 | Speed sensor original Renault 8200547283 / 6001548870 (without ABS) | Original | 1600 / 1100 rub. Discount: 900 rub. | 1 |
DC1665-21800141301000 | Manifold absolute pressure and temperature sensor MAP sensor 1.6l VAZ 21129 original 21800141301000 | Original | 2800 / 2200 rub. Discount: 1900 rub. | 1 |
DC1816-284375765R | Parking sensor 284375765R original (1 piece) | Original | 1200 / 800 rub. Discount: 550 rub. | 1 |
DC1825-353722 | Pin fuse 5A 35.3722 (1 pc.) | Original | 10 / 7 r. Discount: 5 rub. | 5 |
DC1826-35372201 | Pin fuse 7.5A 35.3722-01 (1 pc.) | Original | 10 / 7 r. Discount: 5 rub. | 5 |
DC1827-35372202 | Pin fuse 10A 35.3722-02 (1 pc.) | Original | 10 / 7 r. Discount: 5 rub. | 5 |
DC1829-35372204 | Pin fuse 20A 35.3722-04 (1 pc.) | Original | 10 / 7 r. Discount: 5 rub. | 5 |
DC1830-35372205 | Pin fuse 25A 35.3722-05 (1 pc.) | Original | 10 / 7 r. Discount: 5 rub. | 5 |
DC1831-35372206 | Pin fuse 30A 35.3722-06 (1 pc.) | Original | 10 / 7 r. Discount: 5 rub. | 5 |
DC1832 | 6.3 socket series tip with fixation (crimped with wire) | 15 / 10 rub. Discount: 8 rub. | >10 | |
DC1833 | 6.3 series female tip with locking (without wire) | 10 / 7 r. Discount: 5 rub. | >10 | |
DC1841 | Ring lug 8.2mm (without wire for crimping) | 10 / 7 r. Discount: 5 rub. | 5 | |
DC1844 | Pin lug series 6.3 with fixation (without wire for crimping) | 20 / 10 rub. Discount: 6 rub. | >10 | |
DC1842 | Ring tip 8.2mm (with wire) | 45 / 30 rub. Discount: 20 rub. | 3 | |
DC1843 | Pin lug series 6.3 with fixation (crimped with wire) | 45 / 30 rub. Discount: 15 rub. | >10 | |
DC1847 | Split corrugation for cable with a diameter of 6.8 mm (corrugated tube with a cut) price per 1 meter | 50 / 30 rub. Discount: 25 rub. | >10 | |
DC1848 | Split corrugation for cable with a diameter of 11.5 mm (corrugated tube with a cut) price per 1 meter | 50 / 30 rub. Discount: 25 rub. | >10 | |
DC1850 | Corrugation for cable, cut with a diameter of 9.4-9.8 mm (corrugated tube with a cut) price per 1 meter | 50 / 30 rub. Discount: 25 rub. | >10 | |
DC1867 | Seat back heater connection connector for Largus, Vesta, X-Ray | Analogue | 100 / 60 rub. Discount: 45 rub. | 1 |
DC1892 | Connector for crankshaft sensor Vesta, compressor, turn signals Renault, Lada, Nissan | Analogue | 100 / 70 rub. Discount: 50 rub. | 2 |
DC1900 | Seat heating connector Vesta, Largus, X-Ray, etc. Renault, Lada, Nissan | Analogue | 110 / 80 rub. Discount: 70 rub. | 2 |
DC1913 | Seat heating connector (4-pin male connector analogue 98822-1045 Molex with wires) | Analogue | 110 / 100 rub. Discount: 80 rub. | 2 |
DC1914 | Seat heating button connector analogue 98172-1003 Molex with wires with wires | Analogue | 110 / 80 rub. Discount: 70 rub. | 2 |
DC1915 | Fuse holder connector with wires | Analogue | 110 / 80 rub. Discount: 60 rub. | 2 |
DC1916 | 5-pin relay connection block with wires | Analogue | 110 / 80 rub. Discount: 60 rub. | 2 |
DC1917 | Automotive wire PVAM 1.0 sq. mm, 5 m. | Analogue | 190 / 130 rub. Discount: 100 rub. | 1 |
DC1918 | Connector for lambda probe, oxygen sensor, fuel pump | Analogue | 300 / 240 rub. Discount: 200 rub. | 1 |
DC1919 | Door limit switch Lada Vesta, VAZ 2190, 1118, 2123 original | Original | 150 / 80 rub. Discount: 60 rub. | 4 |
DC1927 | Connector socket for baseless lamp T10 W5W with wires | Analogue | 120 / 80 rub. Discount: 60 rub. | 3 |
DC1933 | Flat fuse holder with cover and wire from 1 to 30A | Analogue | 190 / 120 rub. Discount: 90 rub. | 1 |
DC1935-255404709R | Left steering column switch (without front PTF, horn on steering wheel 2015-) original 255404709R | Original | 8500 / 6500 rub. Discount: 4900 rub. | 1 |
DC1943 | Quick-detachable positive battery terminal with clamp (1 pc.) | Analogue | 900 / 700 rub. Discount: 550 rub. | 1 |
DC1944 | Quick-detachable negative battery terminal with clamp (1 pc.) | Analogue | 700 / 500 rub. Discount: 350 rub. | 1 |
DC1945 | Lubricant for electrical contacts and battery terminals Liqui Moly | Analogue | 600 / 400 rub. Discount: 300 rub. | 1 |
DC1947 | Electrical contact cleaner aerosol 0.2L | Analogue | 500 / 300 rub. Discount: 200 rub. | 1 |
DC1250 | Set of small fuses (10 pcs) | Analogue | 200 / 150 rub. Discount: 100 rub. | 0 |
DC1881 | Headlight connector block H4 with wires Duster, Vesta, Terrano, Logan, etc. universal (1 pc.) | Analogue | 100 / 60 rub. Discount: 50 rub. | 0 |
DC1907-12010996 | Connector for retractor relay Vesta 12010996 | Analogue | 110 / 80 rub. Discount: 70 rub. | 0 |
DC1946 | Lubricant protection of terminals and contacts 210 ml LAVR aerosol in a bottle | Analogue | 600 / 400 rub. Discount: 300 rub. | 0 |
DC1949 | Fuel level sensor Duster, Largus, Logan, etc. | ASAM | 1300 / 1000 rub. Discount: 800 rub. | 0 |
DC1950-172024388R | Submersible electric fuel pump module assembly (one fitting) 172024388R original | Original | 2200 / 1800 rub. Discount: 1400 rub. | 0 |
DC1958-79.3710 | Glove box limit switch 1118,2170,2180 Vesta, Handbrake 2123 - 79.3710 original | Original | 200 / 120 rub. Discount: 80 rub. | 0 |
DC1959 | Cigarette lighter connector Largus, etc. | Analogue | 300 / 200 rub. Discount: 150 rub. | 0 |
DC1959 | Tray for the battery (mat tray for the battery) Largus, Vesta, etc. | Original | 300 / 200 rub. Discount: 150 rub. | 0 |