Regardless of the make of the car, the door is an integral part, but the correct operation of the door mechanisms is no less important. Over time, the door and lock need to be adjusted due to the formation of wear. Otherwise, locking becomes problematic and sometimes even impossible. All work on the door element can be done in a garage with a minimum set of tools.
- How to remove a door
- How to adjust the door
Video: door adjustment using the example of a VAZ 2106
- Door lock VAZ 2107
Working principle of the door lock
- Door lock adjustment
Video: adjusting door locks on a “classic”
- The door does not lock
- Replacing the larva
- External door handle
Which ones can be supplied?
- How to remove the handle
- Video: installing a central lock using the example of a “six”
Replacement of VAZ-2107 door handles
Owners of the domestic VAZ 2107 car know how inconvenient and sometimes unreliable door handles are. These elements often fail, especially if you do not pay attention to them, which entails the need to replace them. In the material we will pay attention to the question of how they are replaced with a VAZ-2107, as well as the main features of the work.
Beet lifter malfunctions
When the window regulator is functioning properly, it is better not to touch it, unless you are going to install an electric one. The mechanism is well regulated at the factory, so any interference with its operation usually ends in breakdowns.
However, like everything else, window regulators sometimes fail. The following signs indicate this:
- jamming;
- creaking;
- glass warping.
Unpleasant sounds that appear when you try to lower the window indicate wear and tear on the moving elements. As a rule, this symptom appears shortly before the final failure of the entire node. Getting rid of the problem is not very difficult - open the door, vacuum the inner cavity and lubricate (or replace) the rollers.
Sometimes unwanted noise appears when the glass no longer fits tightly to the rubber bands. In this case, dust gets into the grooves - that’s why it creaks. Here:
- wipe the seals with a sponge soaked in soapy water;
- dry;
- treat with silicone grease;
- open and close the window several times.
Occasionally the glass simply gets stuck. This happens because:
- serious wear of the star-shaped cable winding mechanism;
- breakage of the pressure plate;
- traction misalignment.
Often older cars have all of these problems at the same time.
Repair is carried out by replacing a failed part or the entire mechanism assembly. It happens that there is a pause between the start of turning the handle and the lowering of the window. In severe cases, the glass does not fix at all or falls inside the door. This breakdown is caused by a weakened cable due to the break of one of the rollers. A part that has become unusable must be replaced with a new one.
What you will need to complete the work
To carry out work on changing handles, you need to stock up on a standard set of tools. The changeover procedure is not particularly difficult, but it will take a lot of time. After all, in order to carry out the replacement work, you will need to remove the door trim, and after that begin the dismantling process.
In addition to the standard set of tools, you will also need to purchase new mechanisms and cylinders to replace the front door locking device. Let’s take a closer look at what the procedure for removing and installing them on the “seven” is.
Changing the external handle on a VAZ 2107
Removing the external door handle on the “seven” is carried out by performing the following manipulations:
When installing new products, we also recommend changing the rubber seal, which should be supplied with the new devices. This seal prevents water from penetrating inside the door.
Features of replacing the internal handle on the seven
Now let’s pay attention to the issue of replacing the interior handle on a VAZ 2107. We change the interior door handle on the “seven” in cases where it jams and does not work to open, but more often than not, it simply breaks. The removal process looks like this:
Replacing the larva
There is another important element in the front door, which is called the lock cylinder. This is a device through which it is possible to lock the door from the outside with a key, which prevents it from being opened by third parties. The cylinder requires replacement only when it fails or gets stuck when opening, and it is not possible to lock the car.
The new cylinder is sold along with the keys, which is something you need to pay attention to. We recommend changing all three cylinders at once: two in the doors, and one on the trunk lid. This will make the further operation of the car easier (all locks will be opened with a single key).
On the VAZ 2106 and VAZ 2109 car models, the cylinders are built into the handles themselves, while on the “seven” this product is located below the door opening mechanism, so its replacement is carried out separately.
To dismantle and change the larva, you will need to perform the following manipulations:
Installation of a new device is carried out in the reverse order of removal. All VAZ-2107 handles are changed in a similar way, and after the change process it is necessary to check their performance.
brand of mortar for garage floor screed
The serviceability of the devices in question on a VAZ 2107 car is very important. If the products are faulty, it is quite problematic to get into or out of the car (if the mechanism is jammed from the inside). Many owners know how unreliable the mechanisms in question are in domestic cars. At the first sign of a malfunction, it is necessary to immediately carry out diagnostics and, if necessary, lubricate or replace the part. Often it is not possible to repair (both internal and external) the device, so it is better to immediately buy new ones. As an option, you can install euro handles.
Source
Preparation for dismantling
To unscrew the fasteners and remove the door trim, you need to prepare a simple set of tools:
- screwdriver with cross slots;
- long flat screwdriver;
- a pointed tool, such as an awl.
Door disassembly tool
Since the door card of the Lada Kalina car is held on by plastic fasteners (otherwise known as clips, pistons), there is a warning regarding the working conditions. It is strictly not recommended to dismantle door trim in the cold, when the plastic becomes brittle and easily destroyed. Hence, there is a risk of breaking all the clips during the process of removing the decorative panel. Therefore, in winter, perform this operation in a heated garage or box.
In the summer, there are no requirements for premises; remove the casing even in the open air. There is only one recommendation: in windy weather it is better to drive the car into the garage, otherwise a lot of dust will be brought into the interior when the doors are open.
This is what the door card lock looks like
How to simply change the inside door handle on a VAZ 2107
The internal door handle of the VAZ 2107 is a standard device that opens the door structure. Replacement will be required after the internal rod breaks, mechanical damage, or if you want to replace the domestic opening mechanism with a euro one. The price of a regular device is half that of a European pen. The door handles of the entire Zhiguli family have the same configuration, so dismantling is carried out by analogy.
Let's sum it up
Since the problem is quite common, we hope that the material will be more useful for Lada Kalina owners. Now we realized that the rear door handles of the car we reviewed should be handled especially carefully so that the rear door handle does not need to be replaced.
We will show you how to replace the outside door handle on Lada Kalina and Lada Granta cars. I think many owners have encountered this problem: the front doors open from the outside without any problems, but to open the rear doors, you have to put in at least twice as much effort to get the lock to work. You have to pull the handle very hard, as a result the mechanism does not hold up and the metal tongue breaks off on the inside. In such cases, the entire handle assembly is usually replaced.
In our case, after removing the door card, the following detail was found:
This is the same metal “tongue” that sets the door lock rod in motion. From the inside, unscrew one nut 8:
Now the handle can be removed from the outside, one part of it can be removed without problems, but the second part will require a little fiddling. A new pen costs around 300 rubles, which is not so expensive that you have to bother with repairing the old one.
When the new handle sits in place, but is not secured. it is necessary to move it as far as possible towards the rear of the car, i.e. back so that the tongue, which was broken off, would engage with the door lock mechanism. In this position, you need to check how the door opens; if everything is fine, screw the handle.
Typical breakdowns and their causes
The interior door handle of the VAZ 2107 is made in black, like the main part of the car’s interior. The wear of this element depends on the activity of transport operation. Over time, scratches or microcracks begin to appear on the device. The filling of the handle dries out, begins to jam, creak, and jam. Damage may be caused by time, an accident, or the door breaking. What can break:
Sometimes the reason is hidden in body deformation or poor door adjustment. If part of the handle is broken, it will have to be replaced completely. This plastic element is non-separable and quite fragile, unlike a Euro pen.
The average cost of a car handle is 900 rubles.
Features of replacement, algorithm of actions
To change the door handle of a VAZ 2107, it is worth considering that they come in left and right. On the driver's side, the structure connects to the door lock. During disassembly you will need to disconnect the wires. The part is screwed to the card with three bolts, but first it is fixed to a special built-in attachment. Before attaching a new device, the opening and closing of the door fragment is checked.
The inner element is connected to the outer handle. If it breaks, you will have to replace the external fixator. To replace the old opening device with a Euro handle, you will need a flat-head screwdriver. The fasteners are hidden under plugs and can be easily removed by prying them with a sharp part of the tool. After this, the process is carried out according to a simple algorithm:
Before installing a new fragment, you need to clean the internal niches from dust and dirt. If detergent is used, you should wait until the elements are completely dry. Experts advise treating with alcohol: it cleans hard-to-reach places well, dries quickly, and erodes.
Source
Removal and installation of components in the door
Euro handles for a VAZ 2107 model car, prepared and painted in the desired color, are assembled and tested for functionality. Preparatory work includes the following operations:
- Removing door trim.
- Removing the handles, locking mechanism and counter part of the lock installed on the rack.
- If the car is equipped with central locking, then it is better to remove the solenoids.
Before installing a new locking mechanism, it is necessary to grind off the plastic housing evenly from the inside. The thickness of the part should be reduced by approximately 5 - 7 mm so that it does not cling to the rack. The work of installing the lock and handle is performed in the following order:
- Place the body of the locking device vertically from the outside and mark the attachment points.
- Drill holes for the bolts according to the marks.
- We combine the parts and connect them together with screws.
- We close the doors and check whether there is sufficient clearance between the lock and the pillar. Using chalk, mark the position of the mate.
- On the body, according to the mark applied, we install a bolt, for which a through hole is drilled through both walls.
At the end of this stage of work, we check the functionality of the lock by opening and closing the door several times. Seizing or hitting of parts against each other is not allowed; adjustments are made if necessary.
Part one: remove the door trim of the VAZ 2107.
In preparation for this repair, you need to stock up on water and a small amount of rags, since the inside of the door is usually covered in dust, and you wouldn’t want to touch the interior elements with dirty hands. Now you need to remove the door trim of the VAZ 2107. To do this, perform the following sequence of actions:
Now we can see the lock mechanism and now the VAZ 2107 door handle on the outside can be replaced.
how to properly prepare walls for wall putty
Mechanism design
The window regulator is a fairly simple mechanism, but it is important to know that the design for the front and rear doors is somewhat different. However, in both cases their equipment is exactly the same. So inside the cabin are located:
- the handle itself;
- protective cap;
- socket.
The window lifting mechanism consists of:
- brackets;
- lower and tension rollers;
- bolt;
- star winding mechanism;
- cable traction.
And the last part is the glass fastening system. It includes:
- pressure plates;
- fixing screws.
The 2107 differs from earlier classic VAZ models in the shape of its front windows - they are pentagonal. The old ones, as many remember, had a separate window, which the manufacturer, striving to optimize work processes, abandoned. Because of this decision, it was necessary to change the layout of the cable and its feeding, so the seven has an additional (tension) roller. You need to know this nuance in order to remove the window regulator without difficulty.
The mechanisms on the rear doors do not differ in any way from those installed on earlier models, therefore they are interchangeable.
Anyone can replace any structural element independently, without going to a service station. However, it is important to complete all work carefully and without errors.
Part three: assembly.
Before assembly, we wipe off dirt from the outside of the door, the hole where the new handle is inserted. It is best to lubricate the rubbing parts with aerosol or grease.
Now we put the new handle in place of the old one. Having inserted it into the hole, we first tighten the bolts, then we insert the rubber band into the hole of the lock and only after this procedure we tighten the bolts securing the handle. When tightening the bolts, make sure that the rubber gasket fits evenly and tightly.
The dirty work is over, you can wash your hands and with clean hands take the door trim of the VAZ 2107. We install the trim in the door by simply pointing the clips into the holes in the door and knocking on the trim with your hand.
We put a decorative trim on the door handle. We install the window lifter handles by first putting a washer on the shaft, then a handle, then insert a stopper between them, making sure that the slots in the handle and on the window lifter shaft match.
We fasten the three bolts of the door handle, insert the plugs and this completes the replacement of the VAZ 2107 external door handle.
Source
Replacing the interior door handle of a VAZ
First you need to remove the window handle. Insert a flathead screwdriver between the window handle latch and the washer. Press the latch, pull it towards you and remove the handle.
Using a curved screwdriver, unscrew the 3 bolts of the door handle, the bolt securing the strip and the decorative trim of the interior handle. You can leave it on if you wish.
We remove the casing with a flat screwdriver, carefully prying it by the edges and slowly overcoming the resistance of the clips. The latches are located on the top right, top left and in the middle inside the casing.
Unscrew the inner door handle and remove it. Do not break the traction control rubber band, otherwise it will slowly rattle on bumps.We install a new one and reassemble in reverse order.
This replacement operation is similar for all VAZ 2105 - 07 cars. If you need to replace the outer door handle of a VAZ 2107, then all this will have to be done in the same way, more on that in another article.
Attached is a video on replacing the inside door handle:
Source
Replacement of the internal handle of opening of doors — logbook Lada 2114 Wigga 2013 on DRIVE2
Replacing the internal door opening handle
Good day) today I was replacing the internal door opening handle (a jock friend tore it off: D) I would like to post detailed instructions for replacing it, because I haven’t found one myself, maybe it will be useful for someone)) So, let’s begin.
1. You need to pull out the plug. Since the entire door card and handle are plastic, there will naturally be kinks, so you should start removing it in a “more or less” inconspicuous place, somewhere below. Out of inexperience, I plucked it out with a screwdriver. In general, advice: pick somewhere where you won’t be able to see the nicks later, and after replacing you can go over it with fine sandpaper.
