According to the maintenance regulations for Lada Granta, Kalina and Priora cars, inspection and testing of the steering must be performed every 15,000 km. mileage The article describes possible steering malfunctions, their causes and solutions.
Steering components Lada Granta, Kalina
Steering of Lada Kalina/Granta VAZ-2190 cars with electric booster and tilt-adjustable steering column.
The steering wheel is mounted on the splines of the steering shaft and secured with a self-locking nut. On vehicles equipped with a driver's airbag, an airbag module is installed in the steering wheel instead of a pad.
The steering shaft is composite. It consists of an upper and intermediate shaft. The upper shaft rotates in two bearings pressed into the steering column tube.
An ignition switch with an anti-theft device is installed on the top of the column pipe. The intermediate shaft is collapsible and has two cardan joints at the ends.
The Lada Granta/Kalina steering column is assembled with a gear motor and an electric power steering control unit. The efficiency of the electric booster depends on the speed of the vehicle.
The electric booster only works when the engine is on. The steering column brackets are attached to the body on four studs with self-locking nuts. The brackets are pivotally connected to the steering column pipe.
The upper bracket is equipped with a steering column fixation mechanism. By moving the locking lever to the lower position, you can change the angle of the steering column. When the lever is raised, the column is fixed in the selected position.
The steering mechanism of the Lada Kalina/Granta VAZ-2190 is rack-and-pinion type, consisting of a crankcase, a drive gear and a rack in gearing. The mechanism is secured to the partition of the engine compartment with two brackets on rubber supports.
When the steering wheel is turned, rotation is transmitted through the upper and intermediate shafts of the steering column to the drive gear, which, when turning, moves the rack.
Steering rods, which consist of the rods themselves, tips and adjusting bushings, are bolted to the Lada Granta/Kalina steering rack. At the inner ends of the steering rods there are eyes with rubber-metal bushings pressed into them.
Ball pins are installed in the outer rod ends, with which the steering rods are connected to the swing arms of the front suspension struts. When the rack moves, the rods rotate the front suspension struts.
The length of the tie rods can be changed by rotating the adjusting bushings and thereby changing the toe-in of the front wheels. The bushings are secured against spontaneous rotation by tightening bolts wrapped in the flanges of the tie rod ends.
Fig.32. Steering Lada Granta/Kalina
1 — tie rod end; 2 — adjusting sleeve; 3, 6 — brackets for fastening the steering mechanism; 4, 5 tie rods; 7 right protective cap; 8 — right steering gear support; 9 — protective cover of the steering mechanism; 10 — steering mechanism; 11 - seal; 12 — intermediate shaft with lower universal joint; 13 — upper universal joint; 14 — steering column with electric power steering; 15 — steering wheel; 16 — contact ring; 17 — steering wheel fastening nut; 18 — steering wheel pad (driver airbag); 19 steering shaft bearings; 20 left protective cap; 21 left steering gear support
Checking the steering of Lada Granta/Kalina
Visually check the condition of the protective covers of the tie rod ends and steering mechanism. Damaged covers (torn, cracked) must be replaced.
Make sure that the steering column locking lever is raised all the way. Trying to move the steering wheel in a vertical plane, we check that the steering column is securely fastened with the locking mechanism.
If the steering column of the Lada Kalina/Granta VAZ-2190 moves, remove the steering column lining and use a 13 mm wrench to tighten the nut of the steering column fixing lever axis.
Trying to move the steering wheel along the axis of the steering shaft, we make sure that there is no play in the steering wheel on the splines of the shaft and shaft in the steering column.
To check the play in the steering, turn the steering wheel to the position corresponding to straight forward movement. We place a slotted screwdriver on the instrument panel so that its blade is located next to the rim of the steering wheel (for reliability, it can be secured with masking tape).
Turning the steering wheel to the right until the wheels begin to turn (selecting play), and then to the left and using the blade of a screwdriver as a guide, use chalk, pieces of wire, or otherwise mark these positions on the rim. The play should not be more than 5″ (or 18 mm) when measured along the outside of the rim.
Increased play indicates the need to troubleshoot and fix the problem. As a rule, the tie rod ends in the Lada Granta/Kalina steering system are the first to fail.
To check that there is no play in the tie rod ends, an assistant slightly rocks the steering wheel from side to side. We place our hand at the junction of the steering rod with the swing arm of the suspension strut so that the palm touches them at the same time.
When play appears in the tie rod end, a displacement of the steering arm relative to the rod will be felt. Check the tightness of the nuts on the steering column universal joint bolts. We repeat the check on the other side of the car. We replace faulty hinges.
When rocking the steering wheel from side to side, listen to the operation of the steering mechanism. A knocking sound from the right edge of the steering gear indicates wear of the support sleeve. We remove the faulty steering mechanism and repair or replace it.
Turn on the ignition - the electric power steering fault indicator light on the instrument panel should light up. Let's start the engine.
The warning light should go out and the steering wheel should turn easily with one hand. If the lamp lights up while the engine is running, it indicates a malfunction of the electric amplifier and the need for repair.
Replacing the steering column of Lada Kalina/Granta VAZ-2190
Depending on the purpose of the work, the steering column can be removed as an assembly with the steering wheel and steering column switches. The operation is described with partial disassembly of the steering column.
— Turn the steering wheel to the position corresponding to straight movement. Removing the steering wheel
— Remove the decorative lining of the steering column.
— Using a Phillips screwdriver, unscrew the three screws and remove the lower trim of the instrument panel.
— Disconnect the wiring harness blocks from the steering column switches and the slip ring.
— Loosen the coupling bolt and remove the connector assembly with the steering column switches and the slip ring.
— Disconnect the ignition switch wiring harness connectors.
— By releasing the clamps, we disconnect the two wiring harness blocks from the electric power steering of the Lada Granta/Kalina.
— You can remove the steering column complete with the intermediate shaft. However, it is more convenient to remove and install the steering column if you disconnect the intermediate shaft.
— The connection of the intermediate shaft universal joint flanges is possible only in one position, so you don’t have to mark their relative position.
— Unscrew the nut of the coupling bolt connecting the universal joints of the intermediate shaft. We remove the bolt.
— Loosen the tightening of the two nuts of the lower mounting of the Lada Granta/Kalina steering column.
— Using the same wrench, unscrew the two nuts of the upper mounting of the steering column.
— Remove the steering column assembly.
— Unscrew the nut of the coupling bolt of the flange of the lower cardan joint of the intermediate shaft. We remove the bolt.
— Using a slotted screwdriver, we open the flange and remove the cardan joint from the splines of the steering rack mechanism shaft of the Lada Kalina/Granta VAZ-2190.
Granta 3 new size
At the same time, at the moment the wheels begin to turn, we mark the boundaries of the free play of the steering wheel on its rim with chalk or wire.
Having measured the distance between the marks, we determine the free play of the steering wheel, which should not exceed 5° (corresponding to a distance between the marks of 15 mm) provided that the steering mechanism, tie rods, front wheel hub bearings and telescopic struts are in good condition.
When turning the steering wheel sharply from side to side at a small angle, we make sure that there is no knocking in the universal joints of the steering column and the steering mechanism. Otherwise, we tighten the loose fastenings of the steering elements or replace faulty parts and assemblies.
An assistant is required to assess the condition of the outer tie rod ends. We hang the front wheels and securely fix the car on factory-made support stands.
Steering of Lada Granta
It is designed to control the car while driving. Structurally, it consists of the following main elements:
The work of the mechanical part is that the driver acts on the steering wheel, the impulse through the steering mechanism and rack transmits force to the front wheels through the levers, and the car turns in the desired direction. A characteristic feature of a passenger car steering wheel is its smaller diameter (compared to a truck). The design of the mechanism also differs. The steering of the Lada Granta is complemented by an electric booster. The steering wheel can be adjusted in height. Unfortunately, there are no settings for departure.
The steering mechanism of the Lada Granta is rack-and-pinion type, the simplest and most inexpensive option.
The drive is mechanical, structurally consisting of levers, rods and hinges. For more efficient and convenient control, the Lada Granta is equipped with an electric amplifier. This is a complex mechanism that provides force through the use of electricity. An electric power steering, or simply EPS, is used to improve dynamic characteristics and controllability. And, according to some data, it allows you to save fuel by increasing the vehicle’s maneuverability.
Steering mechanism malfunctions and their elimination
The steering mechanism of the Lada Granta is quite reliable and rarely causes problems for the owner. However, this does not mean that problems do not occur at all. There are problems. And you need to know how to eliminate them.
| Cause of problems |
Elimination
Like the braking system, engine operation and other important components and assemblies, the steering system must be periodically inspected for malfunctions. If there are no signs, protective boots and other smaller structural parts must be inspected. The steering rack of the Lada Granta is a key control mechanism. It is thanks to this that the car is controlled by turning the wheel.
Not only the comfort of control, but also the safety of the driver and his passengers depends on the serviceability of the steering mechanism. Unit problems must be diagnosed and corrected in a timely manner.
Basic steering rack faults
The main sign of a breakdown is a knocking sound when turning. At first it is almost invisible and appears when hitting potholes. If you ignore the first symptoms, the noise will not go away and will constantly get worse. Then the knock will be transmitted to the steering wheel. If you ignore this symptom, the rack will simply jam, and this risks getting into an accident due to loss of control. The rack knocks due to wear of the hinges, teeth or rubber-metal bushings (damper).
Steering rack adjustment
The unit knocks for various reasons. In fact, this is a real disease of the control mechanism, inherited from the Lada Kalina, since the components are identical on these cars. You can adjust the rack yourself.
To do this you will need a minimum of tools:
- steering rack calibration key;
- socket heads for 10 and 13;
- shaped screwdriver.
To tighten the slats, you can use two methods. The first involves using a special key that can be inserted into the gap of the arch on the left side. The second method is more labor-intensive and is suitable if it is not possible to stick your hand into the gap. To do this, you will need to dismantle the battery and its platform; this is the only way to get to the nut for tightening the gearbox. The first method is simple, so it’s better to consider the second option.
To do this, you need to disconnect the battery terminals and remove it, and then remove the platform under it. Now you can get to the nut located on the inside of the gearbox housing. You can buy a combination wrench for tightening, on the one hand - for tightening the rack, on the other - for tensioning the timing belt.
To tighten the nut, turn it clockwise.
Instructions for replacing the steering column
The steering system of a car must be treated very responsibly, since it is primarily responsible for the safety of the car when driving. If control problems arise, they must be corrected immediately. One of the breakdowns in this system is the failure of the steering column. The procedure for replacing it is quite problematic, but if you have the right tool, you can get by with minor sacrifices. So, we will need:
- Head for 17 and 30
- Long and powerful crank
- Mount
- Hammer
- Ratchet handle
- Regular open-end wrench 17
So, the steering mechanism (column) is located on the left side of the space under the hood of the VAZ 2106, it turns out in the very bottom left corner
It is worth noting that before you start replacing it, the first thing you need to do is remove the steering shaft. When everything is ready, you can begin the repair. First of all, you need to unscrew the lower nut securing the column to the steering rods
To do this you will need a fairly long lever, which can be made from two powerful cranks:
The first step is to unscrew the lower nut securing the column to the steering rods. To do this you will need a fairly long lever, which can be made from two powerful cranks:
When everything is ready, you can start repairing. The first step is to unscrew the lower nut securing the column to the steering rods. To do this you will need a fairly long lever, which can be made from two powerful cranks:
To unscrew it, you will need a very strong force; I pressed my feet from below to break the connection:
In general, it is advisable not to unscrew this nut, since then you will have to knock the column off the splines, which is not a very pleasant task. It is more convenient to simply disconnect the column along with the steering tips. But since I completely disassembled the car, this was not important for me.
After the nut is unscrewed or the ends are disconnected, you can begin to unscrew the bolts securing the steering column to the side member. It is secured with three bolts. To get to them, it is better to remove the front left wheel, it will be more convenient.
We take the head with a 17mm knob and, holding it with an open-end wrench, unscrew the bolts one by one:
Holding from the inside is not very convenient, since there is very little space there; you have to insert the key from the end, especially for the lower nut on one side:
After the bolts have moved out of place, you can use a ratchet, as with it you can do everything much faster.
After the bolts are unscrewed, you can safely move the column to the side:
If the tips are disconnected, the column can be freely removed without any problems. If you unscrewed the largest nut, you will have to knock it off the splines, which brings quite a lot of trouble. The price of a new steering column for a VAZ 2106 and other classic models. If replacement is necessary, we buy a new mechanism and install it in reverse order.
Sources
- https://spike.su/index.php/Steering-rack-VAZ-2101-2106-2107.html
- https://remontysvoimirukami.ru/remont-kolonok-svoimi-rukami/remont-rulevoj-kolonki-vaz-2101-svoimi-rukami.html
Steering wheel tuning on Lada Granta
There are few options for upgrading the steering wheel on the Lada Granta. The most popular of them is installing a sports version. Such a steering wheel will not only make the interior more attractive, but will also increase the comfort of control, especially if it is selected correctly. You can install a multi-steering wheel, but only if the configuration is maximum, in other cases there will be nothing to control with its help.
The sports version must be injury-proof, that is, in the event of an accident it must be deformed without causing damage to the driver. Among the shortcomings, it can be noted that although there is an airbag in the standard steering wheel, the sports one does not have it. You can also modify the steering wheel by installing braid. More advanced ones install a heating thread under it.
To install the sports steering wheel, you will need to carry out the following operations.
- Align the front wheels straight (you can drive a little forward and back so that the trajectory is straight).
- Disconnect the battery terminals by de-energizing the vehicle's on-board network.
- The airbag control module must be disabled (if the Granta equipment is equipped with it). If you do not turn it off when removing the factory steering wheel, it may shoot out.
- Remove the steering wheel and install a horn on the adapter. The wiring must be stored in the adapter; to do this, carefully inspect all contacts.
- Connect the adapter to the shaft, but do not secure it with a nut.
- A sports steering wheel is installed on the adapter and secured with special screws.
You cannot throw away or sell the factory product; the sports version will raise questions when passing inspection.
Power steering and power steering: do-it-yourself installation
The electric booster first appeared on Kalina, then on Grant and on the new Priora. You can drive a car without an ESD. But if a car owner previously owned a car equipped with a hydraulic or electric booster, then, at a minimum, he will experience great inconvenience. On the Lada Granta in the minimum configuration, the manufacturer does not install electric power steering, so many owners of such cars decide to install the power steering themselves. This procedure is not the easiest, and the unit is not cheap. But its presence means a comfortable ride, maneuverability and safety.
Installation does not require any special knowledge or skills; minimal experience and a set of tools are sufficient. If, nevertheless, the question arose about installing electric power steering on the Lada Granta, then when purchasing an electric power steering unit, you should pay attention to its number.
The set of numbers contains a definition of the place of production, these are the last two digits:
- 00 – made in Makhachkala (not the highest quality, has many negative reviews);
- 04 – Korean amplifier, you can buy it in a store, a rare copy at auto wrecking yards;
- 02 – made in Kaluga, a good medium option.
To install the amplifier you will need a set of wrenches, screwdrivers and an angle grinder (grinder). Before proceeding with installation, the steering wheel, all steering column switches, the ignition switch, and the steering column with cardan must be removed. The further algorithm of actions is as follows.
- Knock out the bolts from the removed bracket in the form of a plate and cut off about 3 cm from the top with a grinder.
- Drill holes in the plate to mount the electric amplifier.
- Fix the cardan to the EUR.
- Place washers under the bracket (where the electric booster is mounted), and you can use them to adjust the steering wheel.
- Attach the electric booster, and then install the cardan into the rack.
Let's get started
First you will need to disassemble the steering wheel housing and remove the reverse threaded retaining bolt. Height adjustment is carried out using a special bracket. In the factory configuration, the width of the hole for the bracket is small, which explains the small steering wheel adjustment stroke.
In the absence of this limitation for the bracket, you can lower the steering wheel all the way to the seat.
In order to lower the steering wheel as much as possible without interfering with the mechanics and without using an angle grinder, you will need several washers that fit the size of the bracket mounting bolt.
We place washers under the main bracket, depending on how much you need to lower the steering wheel. To do this, you will first have to unscrew the two front nuts. Particular attention should be paid to the fact that it is the front nuts that are unscrewed; if you unscrew the rear ones, the bracket may fall off the steering wheel, and you will have to spend additional time installing it back. If you need to lower the steering wheel very low, you can place several washers under the second bracket.
After the desired level of the steering wheel is reached, we assemble everything in the reverse order and install the steering wheel cover in place.
The disadvantage of this method is that the lowered steering wheel will partially cover the instrument panel, which will reduce visibility, but the resulting comfort while driving will completely cover this disadvantage. In addition, you can adjust the seat, perhaps this will help solve the problem.
If you want more drastic changes, you can either independently enlarge the slots for the steering wheel bracket, but this will require an angle grinder and some skills, since you need to act very carefully. Or you can simply contact a car service center, where specialists will do this.
Some car owners suggest simply buying a complete steering column, with an initially high-quality adjustment mechanism, but this will require a very good knowledge of all the parameters of the mechanism or you will have to involve expensive professionals in the work. You can also replace a regular steering wheel with a sports steering wheel, including the entire mechanism, and initially install it individually for yourself.
Rack and pinion steering
If we talk in general about the steering mechanism of the Lada Grant, then the following are its main characteristics and features.
- The steering column provides the ability to adjust the tilt of the steering wheel. And the steering wheel itself can be locked by installing an anti-rotation device connected to the ignition switch.
- The steering mechanism is of a rack and pinion type, where it is possible to change the gear ratio in different operating modes.
- The mechanism is mainly equipped with electric power steering.
- The electric amplifier is equipped with a unit that allows you to independently diagnose the technical condition of the device, and, if necessary, exclude the amplifier from operation.
The schematic diagram of the Lada Granta steering device is quite simple. The rack-and-pinion type mechanism is fixed in the engine compartment on a special shield through rubber supports. Reliability of fastening is ensured by bolts welded to the body. Steering drive is provided through two separate tie rods, which interact with the steering arms of the front wheel struts.
Reliability of engagement of the gear pair on one side is ensured by a special gap set at the factory. On the other hand, the precision of engagement is maintained by a spring stop, which presses the rack itself against the gear teeth.
The above gap under normal conditions is 0.1 mm, but during operation it may be violated due to wear of individual parts. Thus, one of the main reasons why an extraneous knock appeared in the steering mechanism is a violation of the set gear clearance. It should be noted that there are other malfunctions that can lead to an unpleasant knocking sound in the car:
- loosening of the steering rack itself on the mounting bolts;
- loosening of the tie rod ball joint;
- wear or destruction of mechanical transmission teeth.
Removing the steering gear
If a knock does occur, the car owner will have to dismantle the mechanism. It is more convenient and faster to carry out this work when the vehicle is on a lift. To carry out the work you will need the necessary tools, which in this case include:
- socket wrench or socket wrench 13;
- flat screwdriver;
- durable knife;
- special 24mm wrench for the steering rack;
- hexagon 6 with wrench.
Before starting work, the battery is disconnected, thereby taking the necessary safety measures. At the initial stage, you need to first loosen the bolts securing the front wheels. The wheels themselves should be left in the “straight” position before lifting the car onto the lift. Next, the steering wheel driveshaft is disconnected from the rack and pinion drive shaft.
This work is carried out from the salon. Therefore, the car is not raised high. The swing rods can now be released by unscrewing them from the swing arms. And as soon as this work is completed, you can begin to dismantle the steering mechanism. Using a 13mm wrench, unscrew the nuts securing it and remove the mounting clamps.
The steering mechanism is removed along with the disconnected steering rods. The next stage of repair work is disassembling the removed device. Here you should free the steering rack from all protective covers that are put on the mechanism. For this purpose, cut off all the fixing clamps, which will subsequently need to be replaced with new ones.
Replacing the steering column
The need to replace the steering column arises if the splines in the connecting pair are worn out, and this connection cannot be restored. To do this, you need to dismantle this mechanism. For this purpose, it is necessary to disassemble the “Shohi” steering column, which even novice motorists can do. The procedure for removing the steering column is not particularly difficult technologically, but preventive measures take a lot of time.
Information for car enthusiasts: when replacing the steering column of the “six”, a slight modernization of this unit is allowed. It is possible to install a steering column from a VAZ 2107, the design of which is complicated by two small cardan shafts, increasing the degree of safety of the mechanism. In addition, additional equipment of the system with needle-type bearings will allow significantly less effort to be applied to the rotation of the steering wheel.
The required replacement of the steering column is carried out in the following sequence:
- We de-energize the battery and carefully remove it from the car and put it aside so that it does not interfere with work.
- We dismantle the steering wheel and the protective coating of the steering column shaft.
- We turn off the steering column control complex and the ignition switch.
- We dismantle the bracket fasteners, and it is possible that individual fastener components will have to be removed using a drill.
- Unscrew the tie bolt connecting the splines to the steering mechanism.
- We dismantle the sealing mount of the steering column shaft, and it is pulled out into the interior room.
Additional information: after completing the repair of the steering column, it is necessary to adjust the wheel alignment of the wheel pair to restore the required conditions of the chassis. It is almost impossible to install the wheelset at the optimal angle yourself without special adjustment equipment and stands.
Important: long-term operation of the “six” with splined joints, subject to increased wear, can ultimately create an emergency situation that is dangerous to the health and life of the driver and passengers. The steering wheel may turn completely uncontrollably, and this can happen at high speed. This is very life-threatening!
This is very life-threatening!
Operating a vehicle in extreme environments or on surfaces that do not meet acceptable standards can cause the steering rack to quickly become loose. This is especially true for VAZ models of the 2108-2109 series. Therefore, the part has to be periodically corrected - tightened. When this no longer helps, you need to carry out repairs or completely replace the rail. Next, we will tell you in detail how to replace the VAZ-2109 steering rack.
To carry out repair work you will need:
- hammer;
- mount;
- extension;
- socket heads for 10, 13, 22;
- ratchet handles;
- collars.
Having prepared everything you need, stock up on additional free time and the desire to do everything as needed, and not carelessly, so that later you have to redo it or send the car to a service station.
Diagnostics, repair and reassembly
Before determining why there is a knock in the steering, you should completely disassemble the rack and carry out diagnostics for wear, destruction of components and connections. Disassembly is carried out in this order. Secure the steering rack in a vice, having previously installed spacers made of soft metal or other material. Unscrew the nut securing the mechanism crankcase pipe. The crankcase tube is removed. Remove the clamps securing the pipe bushings and remove them.
Unscrew the adjusting nut. Here you need to use a special 24mm wrench, which has external edges for unscrewing. Sequentially remove the rack stop spring, the sealing ring and the rack stop. Remove the crankcase cover. After removing the bearing cage and sealing ring, remove the rack. The second element of the steering mechanism pair - the gear shaft - is dismantled.
Now you can diagnose the condition of the bearings and sealing rings. After thorough cleaning, the wear of the gear sectors and the condition of the surface of the rack and shaft are assessed. After all, this is where the reason lies that causes the knocking that appears. If necessary, select the necessary parts and replace them.
Before reassembly, all critical connections are lubricated with a special compound. Very often, it is the insufficient amount of lubricant that leads to rapid wear of loaded parts, which violates the previously established clearance. Therefore, even a recently installed rack knocks again.
Assembling the steering mechanism is carried out in the reverse order. For correct and easy installation of dismantled bearings, you should select the required diameter of pipe cutting, which will help to correctly install the bearings in place. The assembled steering mechanism must be adjusted, since the size of the gap can also determine whether a knock will appear after reinstallation.
A little theory: front suspension design
Before attempting to fix any problem, there is a tendency to look at the blueprints or repair manual. It is known that the VAZ-2192 parts catalog contains the following object:
This is what the steering rack looks like in the drawing
Whether the knock will remain in the steering rack of Kalina-2 depends on the following: how accurately element “14” is adjusted. The adjusting nut, marked “14”, looks almost invisible here. But first impressions are deceiving. In the catalog, by the way, the element is called “Stop Nut”.
Now let's move on to practice and see what the node in question looks like in reality:
If you remove the rail, it looks like this
The nut has a non-standard notch, and it can only be rotated with a special tool. By the way, the recess will be closed with a cap. In the catalog it is designated by the number “15”, and now, let’s look at the appearance of the special key:
Rack adjustment key
The thrust nut is turned at small angles. We are talking about values of 10-15 degrees. What happens if you overdo it with tightening the rack? The knocking noise will disappear, but the steering wheel will turn with difficulty. Therefore, if necessary, the nut can be pulled back.
Rack adjustment
Before installing the rack and rods back, it is necessary to set the gaps of the gear connection. Please note that it is better to immediately replace the thrust nut with a new one. Set the rack to the middle position, as if the wheels were straight. For adjustment, a special clock-type indicator mechanism is used. We start rotating the gear shaft and measure the indicator readings.
If the value is 0.05 mm, then the adjusting nut should be tightened to the same amount. After the steering rack adjustment is completed, check the ease and uniformity of movement along the entire length of the rack stroke. Provided that everything is done accurately, you should fix the position of the adjusting nut by performing special core punching with a punch. When all the work has been completed, you can begin to reinstall the steering mechanism on the Lada Granta. After the mechanism has been installed back on the car, you should, even before starting to drive with the car stationary, turn the steering wheel, checking the uniformity of rotation. A check that will reveal that there is no knocking can only be done while driving on a rough road.
Steering malfunctions usually occur due to insufficiently frequent preventive inspections. If the owner has missed the appearance of minor leaks in the steering mechanism, loss of integrity of the protective covers, then the likelihood that a knock will soon appear in it is quite high. Therefore, it is important to carry out annual diagnostics.
| Large steering wheel play | |
| The fastening nuts on the ball rods have become loose. | The cotter pin may be missing. Tighten the fastening and install a cotter pin if necessary. |
| The clearance in the ball joint rods is too large. | Replacement of steering tips for Lada Granta. |
| The silent blocks of the hinges are worn out. | Replace the rods. |
| There is too much clearance between the rack and nut. | Worn elements must be replaced, and after replacement the mechanism must be adjusted. |
| There is a knocking sound when turning the steering wheel | |
| The tie rod nuts are loose. | Tighten the fastening nuts. |
| There is a large gap between the rack and the nut. | Replace worn elements; after replacement, the mechanism should be adjusted. |
| The steering mount is loose. | Tighten the fastening nuts holding the mechanism. |
| Steering wheel turns too hard | |
| The support bearing of the shock absorber strut is faulty. | Replace the support bearing. |
| The support sleeve is worn, the rack stop is worn. | Worn elements need to be replaced. |
| Tire pressure is too low. | Inflate tires to optimal pressure. |
| Ball joint parts are worn or damaged. | Replace elements. |
| The shock absorber struts or their elements have expired. | Repairing the shock absorber strut or replacing it. |
| The shaft bearings are worn out. | The shaft bearings need to be replaced. |
| The electric power steering is faulty. | Replacement of the EUR together with the shaft. |
Reviews
| № | Positive |
| 1. | Vasilyevich , 44 years old (drive2.ru): the range of adjustment of the steering column vertically and in depth is sufficient for comfortable control and monitoring of dashboard readings. |
| 2. | Vladislav , 45 years old (prom.ua): for my small height (169 cm), the angle of inclination is not enough. I contacted the official dealer and decided to raise the front seat a few centimeters. |
| 3. | Mikhalych , 40 years old (autotoday.com): unlike the Lada Grant, Priora, the steering wheel adjustment for reach and visibility of the dashboard on the Lada Vesta are better implemented. |
| 4. | Kirill Alekseevich , 45 years old (rozetka.ua): one of the factors why I chose Vesta instead of Grant was its functionality and multifaceted settings. |
| 5. | Nikolay , 44 years old, (avtoflit.com): my positive review of the car. A good model, multiple tinctures, domestic cars are “at their best.” |
| 6. | Vasilievich , 39 years old, (autotoday.com): before Vesta there was Priora, there is something to compare with. The model has been improved, the functionality is much wider. |
| 7. | Dmitrievich , 44 years old, (drive2.ru): I bought a Lada model myself and recommend it to others. These are no longer the crude models that were several years ago; the engineers took into account numerous comments from the owners. |
| Negative | |
| 8. | Sergey , 30 years old (prom.ua): the standard settings are not enough for me, I have to use a foam rubber layer. My friends advised me to raise the front seat a couple of centimeters. |
| 9. | Semenovich , 35 years old, (avtoflit.com): I’m no longer glad that I purchased the model, after a year of active use it began to crumble. It was necessary to take Grant, my comrades recommended it. |
| 10. | Sanek , 33 years old, (drive2.ru): the standard backlight is not enough to read instrument readings in the sun. In addition, there is still limited travel of the steering column. |
| 11. | Sergey Vasilyevich , 42 years old, (autotoday.com): I am over 200 cm tall. The range of adjustments is not enough. I contacted the service station, the technicians said they couldn’t help. |
Read more: How to remove a brake drum on a Renault Sandero
