VAZ 2107 trunk lock, device, automatic opening

How to replace the trunk lock on a VAZ 2113-VAZ 2115?

1) As for hatchbacks, their lock can be easily removed, and there won’t be any problems with sedans either, but the principle of replacement on two different bodies is different, first we’ll talk about hatchbacks, if you have a specific car with such a body, then on theirs first remove the upholstery that is attached to the inside of the trunk lid with 10 pistons, it is not at all difficult to remove, all the pistons were pry off with a screwdriver and after that the upholstery was put aside, for more details on how to do this, read the article: “Replacing a spoiler on cars”, point 1 Study the nd in that article carefully.

2) After the upholstery is removed, unscrew two bolts and thereby remove the lock from the car, but only when unscrewing the bolts, take into account the fact that under one of them there are several terminals, one of which goes to the tailgate wiper motor, and the other to the stop -signal, and that’s it, the lock has been removed from the car.

Note! To adjust the lock on this type of car, take a spanner wrench (You can use a spanner if you don’t have a spanner, it’s just possible to break off the bolts securing the lock) and use it to loosen the bolts holding the lock (Do not turn them out completely, in this case, by the way, you are adjusting the position of the lock, due to in a knocked down position, the trunk lid may be difficult to lock, lock with a blow, or it is very poorly fastened and opens at all on bumps), then move the latch in the appropriate direction, ensuring that the lock, when closing the trunk lid, enters the latch without strong force and that the trunk is firmly locked (see photo 1), if you need to adjust the trunk lid in height (In other words, the lid does not lock well and it has free movement if you pull the lid), then in this case completely unscrew the bolts securing the latch, remove it and then then select the adjustment plates behind it (Always remember one thing, the more plates you put, the higher the trunk lid will stand and it will have free movement, the fewer plates there are, the worse the trunk lid is locked and the tighter it is pressed against the body car, and if there are no records at all, then you won’t be able to simply close the lid, so you look for a middle ground, see photo 2)!

3) As for sedans, first remove the plastic clips using a screwdriver, which strengthen the lock cover, and then the cover is removed (see photo 1), and when it is removed, proceed to disconnect the rod, for this the end of the rod (the rod is indicated in blue with the arrow in photo 2) remove it from the hole indicated by the green arrow, but keep in mind that the tip is bent and secured with the screw indicated by the yellow arrow, so first unscrew the screw, then straighten the bent end of the rod with pliers and only then pull the rod out of the hole in which it is located Once this is all done, remove the rod from the hole in the lock cylinder lever (see photo 3) and remove it, immediately after which unscrew the three nuts that strengthen the lock (see photo 4) to the trunk lid and remove it from the studs and Finally, unscrew the bolt that secures the lock

(see photo 5) and remove it (see photo 6).

Note! The new lock is installed in its place in the reverse order of removal; when installing the nuts, do not tighten them all the way at first, but rather tighten them a little and try closing the trunk lid in different positions of the lock, then you will adjust the lock to the lid and it will lock normally!

The procedure for installing doors in the desired position

On a VAZ 2107 car, each of the door hinges is fixed to the pillar with two screws; they must be loosened to move the part. Its position can be accurately adjusted only by releasing the fasteners and with constant monitoring from the outside. The operating procedure is as follows:

1. We set the screwdriver to unscrew and with a sharp blow loosen the door fastening.
2. Slightly tilt or lift the knot and tighten it in this position.
3. We close the door and look from the side and check its position.

We perform the action several times until we obtain a result that suits the owner of the VAZ 2107 car. https://www.youtube.com/watch?v=p7MTXCcw-Cg

Opening the trunk using the VAZ 2107 button

Opening the trunk of a car from a button in the cabin will no longer surprise anyone. Today, such an option on a car can significantly facilitate human labor. Domestic cars have only recently begun to be equipped with such useful options from the factory. But this does not mean at all that this option is not suitable for owners of VAZ-2107 injection and carburetor versions. If desired, you can make a semblance of a foreign car out of any domestic car and vice versa. In this material we will pay attention to the question of how to open the trunk from the button of a VAZ 2107. This procedure is not particularly difficult, especially if there is such a goal.

Convenient button location

Trunk lock VAZ 2107

The luggage compartment lock of the VAZ 2107 has a simple design and fails extremely rarely, but sometimes it may be necessary to adjust or replace the mechanism.

Trunk lock malfunctions

Malfunctions of the trunk lock on Zhiguli cars of the seventh model are usually associated with malfunctions of the cylinder. In this case, the lock will need to be removed from the trunk lid and disassembled to replace the part. As for the adjustment, it is carried out when the luggage compartment lid does not close well or knocks while driving.

The trunk lock of the VAZ 2107 consists of the following parts: 1 - rotor axis; 2 — housing cover; 3 — drive extension; 4 — lever; 5 - spring; 6 - rotor; 7 — body; 8 — clamp; 9 — retainer plate

Trunk lock repair

To carry out repair work on the trunk lock, you will need to prepare the following list:

• wrench 10;
• installation;
• pencil;
• new lock or cylinder;
• Litol lubricant.

How to remove

To remove the luggage compartment lock, perform the following procedure:

1. Mark the position of the lock on the lid with a pencil.
2. Using a 10mm wrench, unscrew the 2 nuts securing the lock.
3. Disconnect the mechanism and remove it from the car.
4. By pushing the larvae inside the lid, it is dismantled.
5. Remove the cylinder together with the spacer bushing.
6. If necessary, remove the seal from the lock.

Replacing the larva

If the need for dismantling is due to replacing the cylinder, then before installing a new part, the mechanism is cleaned and lubricated with Litol. If the lock is completely replaced, the new parts of the product are also lubricated.

How to put

After lubricating the lock, it is installed in the following sequence:

1. Insert the sealing element into the luggage compartment lid.
2. Place the lock cylinder in the spacer sleeve.
3. Mount the cylinder together with the bushing into the lock.
4. Install the lock on the trunk lid in accordance with the previously made marks.
5. Fasten and tighten the mechanism with two nuts.

How to adjust the trunk lock

If the trunk lid lock on the “seven” closes with difficulty, it needs to be adjusted relative to the locking element. To do this, loosen the fasteners and change the position of the mechanism so that the latch easily fits into the body and the lever secures it well, and there is an equal gap between the luggage compartment lid and the body over the entire area.

Adjusting the trunk lid

Sometimes it becomes necessary to adjust the trunk lid. It happens that the part is located above the rear wings or is shifted to the right or left. If the trunk lid can be moved to the sides by unscrewing the fastening nuts on the hinges, then with an incorrect height position the situation is somewhat different.

The trunk lid is adjusted using hinged mounting nuts.

To adjust the lid in height, you will need to open it completely and, holding the edge of the lid with one hand, apply force in the hinge area with the other. A similar procedure should be repeated on the other side.

If the trunk lid is not positioned correctly relative to the rear wings, the hinges must be slightly bent

The main thing is not to overdo it. Then close the lid and check the tightness of its fit. If necessary, repeat the procedure. To adjust the force of opening the trunk lid, the edges of the torsion bars of the springs are shifted to one of the teeth of the luggage compartment hinges.

Trunk of VAZ 2107 - why do you need a luggage compartment

The VAZ 2107 car has a factory-fitted luggage compartment designed for transporting passenger cars or cargo. Because the luggage compartment is an integral part of the body, it is designed to withstand impacts from luggage and absorb the load in the event of a rear-end collision. Access to the luggage compartment opens when you open the lid, which is attached to special hinges and secured with a lock.

Standard trunk dimensions

The torso of the VAZ 2107 is far from ideal, that is, the free space in it is not distributed in the best way, which is typical for other classic Zhiguli models. Due to the special design of the body and its components (fuel tank, side members, wheel arches, etc.), a certain space is created, called the luggage compartment, which is not easy to measure. For a better understanding of the dimensions of the cargo compartment, below is a drawing that shows all the necessary dimensions taking into account the geometry of the rear part of the body.

Trunk seal

The trunk lid of the "seven" is sealed with a special rubber element, which is attached to the flange of the upper part of the trunk. Over time, the sealant becomes unusable: it becomes loose and cracks, as a result of which dust begins to penetrate not only inside the barrel, but also inside. This situation indicates the need to replace the rubber product, and one of the main issues is the choice of a quality element. Today they are considered the best gaskets for the trunk lid BRT (Balakovoresinotechnika). You can install tires from a VAZ 2110, but the lock will have to be adjusted, since the gasket is a little thicker and the lid is difficult to close.

There is no doubt about the immediate replacement of the gasket. After disassembling the damaged product, the new part is evenly distributed around the entire perimeter of the slab. To prevent water from getting into the trunk in case of rain, it is better to make the connection from the rear rather than the front. Squeeze the rubber lightly along the curves, but avoid creases. After uniform distribution, the gasket is finally compacted with a hammer.

Trunk trim

To improve the interior space of the VAZ 2107 trunk, you can use a variety of materials, especially since the original trim is made only in the form of plastic elements. Carpets are the most commonly used covering materials. In most cases, subwoofers, boxes and podium speakers are sheathed with this material, but there are also drivers who use this material to weave interior parts (trunk, dashboard parts, door moldings). Using carpet, you can not only give your car individuality, but also provide sound insulation, which is practically absent in the “classics”. In addition, carpet is one of the available materials, whose properties are practically not inferior to more expensive ones.

In addition to the luggage compartment itself, it is possible to cover the trunk lid, since its inner surface is not covered with anything. The "Seven" does not sell ready-made rear door kits, so the owners have to do everything themselves. The same mats can be used as material. All you need to do is cut the material to the shape of the inside surface of the lid and secure the rail using special plastic plungers or self-drilling holes in the pre-drilled holes.

Trunk mat

In the trunk of a VAZ 2107 you can transport various cargoes (fuel cans, milk, bricks, livestock, etc.), so the likelihood of floor contamination is quite high. An accessory that protects the luggage compartment from penetration and exposure to various contaminants is a mat. The product must meet requirements such as increased durability, ease of maintenance and resistance to chemicals, which depend on the materials being transported. 7 trunk mats are usually made of plastic or polyurethane.

Benefits of this option

Many people do not find anything special in this option, but once you try the electric trunk drive, you immediately begin to appreciate all the advantages. The positive aspects of the option to automatically open the trunk on the VAZ-2107 include:

1. Convenience. By the time the driver leaves the cabin, the trunk will already be open.
2. Practicality. There is no need to remove the keys from the ignition switch to open the trunk with the key, especially if you have just started the engine and are warming it up.
3. Fashion. Almost all modern cars are equipped with such an interesting option, so the “seven” with this function will look more interesting against their background, especially with tuning.

Next, we’ll look at what the procedure for installing an electric drive for opening the trunk on a VAZ 2107 is with your own hands.

What is required for the work

Before starting the work process, you should purchase the necessary equipment. To carry out the work you will need:

• A button that, when pressed, will activate the electric drive. The best option is a button from a VAZ-2110 car, the cost of which is about 50-80 rubles.
• The relay is four-pin and has a special terminal for it.
• Activator.
• Wires.
• Female and male connectors, as well as electrical tape and heat shrink.

You can easily find any of the components in any auto store, and then install and connect it to your car yourself.

Installation of the activator

Initially, it is necessary to install an activator, which is an electric drive that works to retract or repel, depending on the connection. The first step is to remove the lock and install the activator rod. To remove the lock, you will need to unscrew two nuts.

After this, you need to drill a hole in the side of the lock to insert the rod and connect it to the lock tongue. The rod will need to be bent (secured), it should look something like the one shown in the photo below.

After fixing the rod to the lock, the latter can be installed in place. It is advisable to remember the tilt level of the lock and install it as well, so that you do not have to adjust it during installation. Now you can attach the activator to the trunk. To do this, you will need 2 self-tapping screws and a special plate, which comes with the product. After this, you can manually try to see if the lock will work when opening. When the activator is installed on your VAZ 2107 car, you can proceed to the next stage - connection.

Connecting the product

Before carrying out connection work, be sure to disconnect the negative terminal from the battery. To begin with, we present the diagram according to which the product will function.

The electric lock will be supplied with 12V power directly from the battery, although you can also use a wire from the cigarette lighter. First, connect the wire to the “+” terminal of the battery.

The battery supplies power to the relay, which can be located both in the cabin and in the engine compartment, which will be much more rational. From terminal “86” the wire is fed to the trunk opening button, which can be located in any convenient place on the dashboard. To install the button that will open the trunk lid, you will need to drill a hole of the appropriate diameter in the dashboard.

The wire from the relay terminal “30” is laid through the cabin to the activator. Its length must be at least 5 meters. The wire can be laid together with the standard wiring. This wire must be connected to the green wire of the activator using female-male connectors. The blue wire must be short-circuited to vehicle ground. Now you can check how the electric trunk lock of the VAZ 2107 functions. It is enough to spend 2-3 hours so that the trunk will eventually open using the VAZ 2107 button. After completing the work, do not forget to connect the negative terminal to the battery.

Alternative trunk opening for VAZ 2107

Many owners of domestic cars, due to the lack of opportunity to purchase a more expensive vehicle, are trying to make their cars more comfortable. One of the options for improving the functionality of the VAZ 2107 is to control the trunk lock from the passenger compartment. This can be done either using a button or using a cable, which eliminates the need to open the mechanism with a key.

Opening with a button

As the owner of the “Seven”, equipping the car with a device for opening the trunk with a button will not be difficult. The positive aspects of the electric drive include the following:

• convenience;
• practicality;
• following fashion.

Installing a trunk lock control button allows you to control the mechanism from inside the car

Some motorists believe that such an option on the VAZ 2107 is useless, but it’s still worth trying and seeing the usefulness of such a device. If you have decided to install an electric trunk drive, then first you will need to prepare the necessary parts:

• four-pin relay and a special terminal for it;
• activator;
• wires;
• button;
• female and male connectors, as well as electrical tape and heat shrink.

To install an electric lock on the trunk lid you will need an electric drive, wires, connectors, terminals and a button.

The activator is an electric drive, the operation of which is based on retraction or repulsion, depending on the installation diagram. First you need to remove the lock and install the drive rod. In order to be able to influence the lock tongue, you need to drill a hole in the side of the mechanism and bend the rod itself slightly. Once the rod is secured, the lock can be put in place. To avoid adjusting the mechanism, you should first mark its location with a marker or pencil. Next, you need to secure the electric drive, which will require 2 screws and a plate included with the device. Having fixed the product on the lid, proceed to the connection stage.

To be able to control the trunk lock from a button, you will need to connect the electric drive rod to the tongue, and attach the activator itself to the trunk lid

Before starting electrical work, remove the negative terminal from the battery and study the connection diagram.

Installation of the electric lock is carried out according to the electrical diagram

The electric drive device is supplied with power directly from the battery or through a fuse. Electrical installation consists of the following steps:

1. Voltage is supplied from the battery to the relay in accordance with the diagram.
2. Relay contact No. 86 is connected to the electric lock control button. The button is located on the dashboard in a convenient place.
3. Using a wire, contact No. 30 of the relay is connected to the green conductor of the electric drive using connectors.
4. The blue wire of the electric lock is connected to the vehicle ground.
5. Check the operation of the device.

Video: installing an electric trunk lock on a VAZ 2107

Exiting the trunk lock cable to the passenger compartment

The trunk lock on the “seven” can be opened using a cable pulled into the car’s interior. To implement this idea you will need:

• cable 4 m long and 1.2 mm in diameter;
• braid 4 m long from bicycle cables;
• braid ends and cable clamps.

In order to be able to unlock the trunk lock using a cable, it is necessary to make holes in the mechanism to thread the cable and secure it to the tongue. Then they lay a cable from the lock to the driver's seat through the trunk lid, and install a suitable lever to open the mechanism. As a lever, you can use the hood opening mechanism from the VAZ 2109, on which the cable is attached. All that remains is to check the operation of the design.

Photo gallery: installation and routing of the cable to the trunk lock

To control the trunk lock using a cable, you will need the cable itself, a braid and some components

The cable is attached to the tongue of the trunk lock to control the mechanism

The cable from the trunk lock is laid to the driver's seat

The cable control lever is installed near the driver's seat

Door adjustment VAZ-2109AutoRemka – Car repair

On a VAZ-2109 car, and not only on this model, one of the necessary procedures is door adjustment. Each car owner should be able to cope with this process independently, without resorting to the services of a car service. Incorrect closing and opening of car doors may be due to the fact that the car was involved in an accident. In some cases, after serious accidents, one adjustment is not enough. When it is necessary to replace faulty doors, a competent approach is very important, since new body elements do not always “fit” without problems - they need to be adjusted.

Tools

In order to adjust the fit of the doors in the VAZ-2109 you will need only 2 tools - a hammer and a screwdriver.

Front doors

You can set them in the correct position by changing the location of the latch. You can do this in the following way:

1. Before you begin making adjustments, you should note the original location of the clamp. This is best done with a marker.
2. If the closing movement of the door is too tight, you need to loosen the clamp, move it a few millimeters outward and then tighten the fastening bolts.
3. In case of a loose fit, the latch, on the contrary, should be “recessed” a little.
4. When the door moves vertically, depending on whether it sags or is above the level, we adjust the lock in accordance with the problem. That is, if the door has sagged, we pull the latch up, and if there is a gap at the threshold, we move the latch a little up.

Tip: When performing work on adjusting the door, be careful that it does not sink or protrude, but is exactly level with the car body.

Rear doors

If the rear doors of the VAZ-2109 are loose, the problem can be solved as follows:

The hinges that hold the rear door of the car must be loosened and then, with it in the correct position, the door fasteners must be tightened.

Recommendation: In order to accurately determine how much the rear door hinge has shifted during the adjustment process, before starting work, just as in the case of adjusting the front doors, outline the brackets along the contour with a marker.

You can check how much the door has sagged like this: open the car door slightly and apply a gradually increasing load on it from 0 to 100 kg and back.

Adjusting the hood position

In order to adjust the hood cover, you must perform the following steps:

1. Loosen the bolts that secure the iron roof to the hinges.
2. Place the hood in the desired position (it is better to do this with three people).
3. Tighten the hinges using the required wrench head.

If closing the lid does not go well, you need to unscrew the pin, move it to the desired position, fix it with a key and make sure it works correctly

Luggage compartment of VAZ-2109

To solve the problem with closing the fifth door of the Nine, you will have to adjust the lock. You can do it this way:

1. Using a marker, outline the boundaries of the original location of the castle as accurately as possible.
2. Move the latch itself to the desired position.
3. Using a key of the required size, tighten the bolts securing the lock and check the functionality of the lock. If it works well, the bolts can be tightened all the way.

Installation of "quiet" locks

Unfortunately, the locks installed by the manufacturer produce not very pleasant metallic sounds during the operation of the car. If you don’t like such a loud mechanism, it can be replaced with a silent one. Today you can purchase “quiet” locks at any auto store or market. The choice of these new generation mechanisms is truly very wide - there are silent locks of domestic and foreign production. We recommend choosing Russian-made locks.

The replacement process is as follows:

1. Take with you a good impact screwdriver, maybe even a Soviet-era one (you'll have to be patient and strong, since the bolts are screwed in very tightly).
2. After removing one bolt, insert a pin or spoke into the hole to prevent the inside of the lock from falling.
3. The old lock must be removed and a new, silent mechanism purchased in advance installed in its place.
4. After tightening the bolts a little, you should make sure that everything works perfectly.
5. Using the same power screwdriver, tighten the mounting bolts as tightly as possible.

Thus, by following the above steps, you can save money and gain invaluable experience in fixing your car. Savings are no less important, because if you do the work yourself, the only cost will be the purchase of new components.

autoremka.ru

Replacement of VAZ-2106 doors

The biggest problem for a motorist is corrosion of the metal of car doors; replacement may be necessary for both the front door (and the driver's door is no exception) and the rear one. The price of door repairs in specialized auto repair shops can be unreasonably high, and the only option is to replace the door yourself.

To replace, you can purchase either a new door or a used one (previously used), already assembled with glass, door handles, and seal. At the same time, you should make sure that they are of good quality, especially the seal, card and door trim. The main thing is not to make a mistake and not to purchase “left doors”, which, although they will have the required markings and dimensions, will not fit your car. Either door moldings or various stickers are installed, which an unscrupulous seller can use to hide traces of corrosion.

The process itself will not take much time and a small set of tools:

• powerful Phillips screwdriver (power or impact) with a key for it
• hammer
• pliers.

Work order:

1. first, open the door that needs to be replaced and use pliers to compress the limiter until the ends come out of the holes in the body;
   Removing the limiter
2. Using a screwdriver, unscrew the bolts with which the door canopy is attached to the body (three bolts on top and two on bottom).
   If the force is not enough, you can use a hammer or a screwdriver; Unscrew the bolts on the door
3. Having unscrewed both canopies, remove the doors.

We install the door in the reverse order, but it may happen that it does not close. Then you will need to adjust the doors, or the door does not match your sample.

Below in the video you will clearly see how to remove the door of a VAZ:

Roof rack VAZ 2107

The VAZ 2107 roof can be installed as an old style boot as well as a modern type. The standard Zhigulov trunk has dimensions of 1300 * 1050 * 215 mm, and its lifting capacity is up to 50 kg. The fastening of this structure occurs through a roof gutter with screws. Roof shears can usually be divided into 3 groups:

What types of luggage racks are there?

• Open;
• closed;
• In the form of stands.
• The first option is universal. It consists of transverse and longitudinal metal beams with a square or round profile.

A closed trunk is a coffer (chest). The main advantage of such a structure is the protection of transported goods against adverse weather conditions.

The product, made in the form of chests, is used to transport bicycles and other equipment. This design is less commonly used, but the load can be easily and safely attached to it.

There are many manufacturers of VAZ 2107 roofing on the Russian market. Among the most popular companies are: Mamont (Russia), Golislino (Russia), Belts (Belarus), Inter (Russia). The price range of products varies from 640 pp. to 3200 pp.

Which manufacturer to choose

Structurally, the "Seven" roof has a water drainage system to which a boot can be attached. The trunks installed on the roof of the VAZ-A 2107 must be at the same distance from the front and rear windows. This way the load on the upper body and frame is evenly distributed. The spacer handles are located so as not to interfere with the opening and closing of the door. On the last 7 Zhigulas, there are special markings in the interior indicating where the front stringers are located. This simplifies the installation of the product on the roof and its placement.

How to install

Before tightening the spacers, make sure they are parallel to each other and not tilted. Otherwise, the roof surface may be damaged. After installing the supports, tighten them firmly so that the rubber elements are pressed tightly against the gutters. The product is ready for use after the luggage structure is securely attached to the body. The most important thing is that the load is properly secured to prevent it from being lost during sudden braking or maneuvering.

Nowadays, a car trunk is increasingly used for its intended purpose, so for greater convenience it must be properly prepared. In the trunk of a VAZ 2107, many people make a false floor where the necessary things and tools are located. This kind of work is not difficult to do with your own hands, since it requires a minimum of tools and materials. In this way, you can improve the condition of the luggage compartment and increase its functionality, which will ensure comfortable use of the vehicle.

Tuning VAZ 2109

The rear of the eighth and ninth series VAZ cars are designed in such a way that when there is a counter flow of air, they contaminate the rear viewing window of the vehicle. These models drive almost all the time with a dirty rear end. And accordingly, with contamination of the rear part of the vehicle, sand, dirt, moisture and salt solutions get into the trunk lock structure, leading to corrosion on the critical mechanisms of the lock, which often leads to its failure.

But the opening of the mechanism can be activated using a button that is located at the driver’s hand in the car interior. Thus, you don’t have to worry about dirt in the closing mechanism, and it will create more trouble for intruders who want to check the contents of the trunk. It is possible to improve the “closing-opening” device of the trunk on most Zhiguli models.

Installation of electric trunk opening lock VAZ-2107, VAZ-2105

Dear friends, today we will tell you about another small useful tuning, conceived for the convenience of using our fives and sevens in everyday life, namely, we will install an electrically driven lock (actuator) on the trunk lid so that you can open the trunk without leaving the cabin, or if you have a programmable free channel on the alarm, then you can connect the trunk opening to your alarm and open the trunk from the alarm key fob with one click of a button, while smart alarms will also disable the trunk security zone if you have everything correctly connected and the installers did not cheat.

Do-it-yourself adjustment of VAZ 2109 door locks

The locks are adjusted after an accident, when the factory position of the door changes location due to body deformation, or when installing a new door. It is necessary in order to eliminate the appearance of distortions and gaps that violate the seal of the body and allow dust to enter the interior, as well as to ensure that the door closes better. It happens that when the lock is assembled correctly, the door does not want to close and you have to apply a lot of force. In addition, incorrect adjustment of the locks leads to the appearance of characteristic noises in the car door, which can become an irritant for the driver.

How to adjust the front doors

Front left door lock VAZ 2104: 1 - internal lock drive lever; 2 — spring of the locking lever; 3 — external drive lever; 4 — lock switch rod; 5 — rod of the lock lock button; 6 — bracket; 7 — lock button; 8 — external drive rod; 9 — external handle of the lock; 10 — lock switch; 11 — cracker spring; 12 — retainer block; 13 — lock rotor; 14 — external drive rod; 15 — lock retainer body; 16 — lock ratchet; 17 — spring of the central roller; 18 — lock release roller; 19 — central roller; 20 — locking lever; 21 — rod of the internal drive of the lock

On the “nine” body, a special latch is installed in the doorway, which is responsible for the correct closing of the doors and regulation of the gaps when closing them. Changing the position of the latch can greatly affect how the door closes and what gaps there will be. Before starting the adjustment, the door is opened and the lock is loosened. There is no need to unscrew the bolts all the way. It is enough that the latch begins to move freely relative to the body.

Listed below are all the problems with the door and how to fix them.

• The door closes very tightly. The clamp must be moved outward and the fastening bolts must be tightened. Continue this procedure until the door begins to close properly.
• If the door closes too weakly, then you need to do the opposite - push the latch inward and tighten it.
• In the case when the door goes down or up when closing, the latch needs to be raised or lowered accordingly.
• Sagging doors can be eliminated by tightening the lower hinges or installing spacers under them. It is advisable to make gaskets from a rigid material to prevent further deformation of the gasket and repeated sagging.

VAZ rear doors

Adjustment of the rear door locks is similar to the front ones. However, it is not limited to moving the latch. In addition, the VAZ 2109 has the ability to change the position of the hinges, which expands the range of adjustment.

Adjusting the trunk lid gap

Adjustment of the gap and closing force is achieved by changing the position of the internal lock and hinges of the trunk lid. During adjustment, the bolts are first lightly tightened, then the operation of the lock is checked. The procedure is carried out until the gap becomes minimal, and the door begins to close with minimal effort.

That's all. As you noticed, adjusting the VAZ 2109 door locks is not difficult and can be easily carried out in standard garage conditions with a basic set of tools.

vipwash.ru

What to do if the trunk lid of a VAZ 2115 does not stay on

Repair of trunk lid fastening of VAZ 2115

The trunk of the VAZ 2115 may have a problem with the lid not holding on. The lid is held in place by two torsion bars. However, over time they fail and will hit painfully if this problem is not corrected. There are several ways to solve this.

First, you can buy and install new torsion bars. They are not very expensive, but they are not so easy to install. You need to remove the back seat, take out the shelf and place a stick under the trunk lid - it’s easier to install it on an open trunk

It is important to install carefully so as not to break the rear glass

Secondly, you can buy two clutch springs for the classics and make two metal strips that will be attached to the screws securing the trunk trim. We will strengthen the springs behind them. It is more convenient to install springs that are attached to the body.

Third, you can buy a gas shock absorber for the trunk of a VAZ 2108 and attach it to the trunk hinge on one side and to the body on the other. However, the lid will close tightly if two shock absorbers are installed. With one shock absorber, the trunk will warp and the hinges will fail.

Fourth, you need to drill a hole where the shelf is attached and the seat is latched. There we fix one end of the stop. Then you need to clean the welding areas. The second is installed in welded rectangles to the trunk lid levers. After welding, you need to putty and paint. The trunk will open from a button in the cabin.

Adjusting torsion bars

Perhaps the problem can be solved by adjusting the torsion bars.
To do this you need to remove the rear shelf. One side of the torsion bar is fixed in a certain position, and its left part is secured with a nut. The torsion bar on the right is released, the nut on the left is unscrewed and the part that secured the torsion bar is moved in the opposite direction. Then the nut is tightened and the torsion bar is returned to its previous state. Now everything is ready. You can also remove the hole in the body from the bottom of the trunk rubber. Install one end of the shock absorber into the hole made, screw it on, unscrew the bolt that holds the trunk lid on one side and screw it together with the shock absorber.

In addition, you can modify the trunk itself. The plastic is glued with carpet and installed in the trunk, screwed using self-tapping screws; it is better to fill the screw-in points with anti-corrosion agent. Plywood is laid on the trunk floor, which can be cut to the desired shape. The carpet is attached to the plywood. You can also make a strap for the spare tire cover.

Lada 2107 Russian AVTOSH › Logbook › It's done! Open the trunk with a button)

We will need:

1. Activator - 1 pc. I have 9 kg, enough for my head.(

someone says actuator, I honestly don’t fully understand who is who