Enabling and disabling Valet mode on Sherkhan alarm systems 5, 6, 7, 9 series

What does “Zzz” mean on the Sherkhan keychain? This question arises regularly among owners of alarms equipped with alarms from the Logicar and Magicar families, since it is not difficult to accidentally activate the Valet function here. This is often mistaken for a malfunction: the car stops responding to blows, the autostart does not work, the control LED is constantly on... One involuntarily recalls the saying that in Russia they read the operating instructions only when something breaks. And even then not always.

In fact, there is no sign of any malfunction here. The “Valet” mode on the “Sherkhan” alarm system, like other manufacturers, allows you to disable its security functions. Only the central locking, additional channels activated from the key fob (for example, trunk control, if connected), and the turbo timer continue to work. In addition, the ability to program key fobs is blocked, which is why this function was designed: you can transfer the car into the wrong hands (for example, to a car service) without key fobs, without the risk that it will leave with an “extra” key fob in memory.

This makes no sense, and for several reasons. In your absence, it is easier for a potential lover of someone else’s to disable the blocking in advance. If there is a code grabber, the old Sherkhans do not pose any problems for the hijacker. So Valet is a purely decorative function, with no practical meaning.

How to enable/disable Valet status

The site employs an auto electrician-diagnostician, a certified StarLine specialist. If you have questions about car alarms, ask them at the end of the article in the comments or on Vkontakte. When applying, please indicate the make of the car and the model of the alarm.

Since it’s easier to turn on “Valet” on “Sherkhan” from the key fob, you just need to remember the combination 1+3 - by briefly holding these buttons when the security status is disabled, you will activate the service alarm mode. It also turns off.

To disable Valet on Sherkhan without a key fob, use a multifunction button, which is displayed in a prominent place in these systems (for Logicar it is combined with an LED, for Magicar it is on the back of the driver call sensor). However, the control algorithms here are more complex than the key fob offers.

To activate the service mode you need:

1. Disarm the car and turn on the ignition.
2. Press and hold the service button for 2 seconds (the light should blink once).
3. Briefly press the button again. After this, the light will flash twice if a PIN code is not set in the alarm settings, or once if a PIN code is set.
4. If a PIN code has been set, you will need to enter it. To do this, you need to quickly press the button the number of times that corresponds to the first digit of the code, wait for a single flash of light, then repeat the same steps for the remaining digits.
5. After a pause of no more than five seconds, press the service button. Valet mode will turn on.

The “Valet” button on the “Sherkhan” alarm system can also disable the service mode, while much fewer actions are performed: it is enough to hold it down for two seconds with the ignition on.

Instructions for Univers models

If you do not have a Universe 1, 2, 3 alarm remote control, follow this diagram.

1. Open the car door. Security mode is activated.
2. Insert the key into the ignition and turn it three times from the “Off” to “On” position. This must be done in four seconds.
3. Turn off the ignition. If done correctly, the siren should go off.
4. After four seconds. The blockage will be removed from the starter. The “Valet” mode of the Universal security system is activated. The LED will light up continuously.

Requirement of a PIN code

The “Valet” mode is not the only thing the service button controls. It is also used to disable security without a key fob: just open the door with the key, turn on the ignition and hold down the Valet button for two seconds. If the PIN code is not set by the owner, the car will be disarmed.

• How to completely turn off the alarm without a key fob so that the car engine starts

Now imagine how much time a car thief will spend pulling out the door rod and turning the ignition lock cylinder. Without a given pin code, Sherkhan is not able to protect against even the most primitive hacking, and this must be remembered.

Valet on telematic alarms and mobile applications

The first family of Scher-Khan alarms with telematic capabilities was Universe - controversial and at the time of its debut, which caused not the most flattering reviews, since Universe 1 worked in pure Slave mode, without additional authorization mechanisms - wearable tags appeared only in Universe 2.

However, this is not relevant to the topic of the article. As for the service mode, its management has been changed. The “Sherkhan” alarm system, which does not have its own key fob, can turn on the “Valet” function (renamed here to the “Car Service” mode) through a mobile application, the “Commander” interior unit or via a GSM channel (by call or SMS).

On the mobile app, drag the screen to the left to display the side menu. In it, select the appropriate item (we will leave the phrase “Enable car service” to the conscience of the authors). After this, all that remains is to confirm your choice.

Without a mobile application, you can simply call the SIM card number installed in the central alarm unit and dial the appropriate command. The system is put into the “Car Service” mode with the command *6#, and removed using *3#. We type the same commands on the Commander interior module, which has built-in alarm control LEDs. Please note that in both cases

the alarm will ask you to enter a secret PIN code. Unlike other Scher-Khan systems, here the PIN code is initially set at the factory and is indicated on the plastic card included with the security system.

Control of Universe systems is also possible through the manufacturer’s Internet portal, but it does not provide a function for switching to service mode, unlike portals from other companies.

For Mobicar alarms, the mobile application connects to the alarm not via the Internet, but via Bluetooth. Therefore, the company has released its own application for them, which differs in interface from the one made for Universe.

And control of the service mode is placed in a separate menu item.

• Step-by-step instructions for setting up autorun on Sherkhan 7

Here, fortunately, the menu is written out more clearly, and after selecting the “Enable Auto Service mode” item, no confirmation is needed. The color of the machine icon changes, indicating that the service mode is activated, and the window title also indicates this.

In service mode, the alarm retains all the capabilities of monitoring the status through a mobile application, and the functionality of the driver call button in the cabin is also maintained.

Something else useful for you:

Video: Management and configuration of Scher-Khan

VidSyst.ruManufacturersScher-KhanEnabling and disabling the Valet mode on Sherkhan alarms 5, 6, 7, 9…4minute(s)

In some situations, the car owner has to hand it over to third parties for maintenance or repair. For these cases, a minimum security mode is provided while maintaining certain alarm functions.

It is worth understanding how the Valet mode is activated on Sherkhan security systems, and what features of its use are important to consider.

Why do you need valet mode on Sherkhan alarms?

When a driver takes his car to a car wash or service center, he cannot leave the security system on - this may prevent the service personnel from working on the car.

• Shere Khan 3 autostart how to enable

For such cases, the Valet mode is provided. Thanks to this function, you do not have to give the alarm key fob to the service center employees.

After activating the service mode, most functions of the anti-theft system will be disabled. At the same time, you can lock and open doors using the key fob.

Since the Valet mode is intended only for transferring the car to a service center, it is not recommended to turn it on regularly during daily use - in this case, the risk of car theft increases significantly.

Where is the Valet button?

The location of the service button must be chosen by the car owner. It is usually hidden in a visible place or installed in a hard-to-reach compartment. It is better if the button is placed in an inconspicuous place.

If the button can be quickly detected, it will not be difficult for attackers to hack the security system and steal the car.

Features of the button and its placement:

• the service button is small in size and is connected to the standard wiring of the main module;
• the device is hidden in the cabin, and when installed at a service center, information about the location of the button is communicated to the car owner;
• Usually the valet button is installed on the signal receiver, under the steering block or in close proximity to the gas pedal.

If there is no information about the location of the button, it can be easily found through the wires from the main unit of the security system. If you have instructions, you can find out the purpose of each wire and find the button using cables of a certain color.

How to enable Valet service mode?

On many Scher-Khan anti-theft systems, you can enable the service mode using one combination of buttons. It is activated by pressing the “1” and “3” keys on the main key fob.

When the Valet mode is turned on, the window closers stop working and the sound signals are turned off. On the display, the service mode is indicated by four letters Z (Zzz).

In the Magicar 7 and Scher-Khan 9 alarm models, it is possible to activate the Valet mode without a key fob.

To do this, perform the following sequence:

• put the car in the “disarmed” mode;
• turn on the ignition;
• hold down the key on the call sensor body for 2 seconds;
• wait until the hazard warning lights flash;
• quickly press the call sensor button - it should be pressed until 5 seconds have elapsed since the light signal;
• if necessary, enter PIN 1;
• the hazard warning lights will flash 2 times;
• Briefly press the call sensor button within 5 seconds.

After these actions, the service mode will be enabled. The system will notify you of the transition to minimum functionality with a single siren signal.

The key fob will also beep once.

Activation features on Sherkhan 7 alarm models:

• You can open and lock doors using the “1” and “2” keys.
• There is access to the luggage compartment lock.
• The use of additional channels is allowed.
• You can activate turbo mode.

It is worth remembering that you can activate the Valet mode by accident - just hold down 2 buttons in your pocket for the car’s security to switch to minimal functionality.

In such cases, it is worth figuring out how to turn off the service function.

How to disable it?

You can turn off Valet mode in the same way as turn it on. You will need to disarm the car (open the locks) and press “1” + “3”, holding the buttons for 5 seconds.

There is a second way:

• turn on the ignition;
• press the LED indicator button;
• hold the button for 2-3 seconds.

As a result of these actions, Valet mode will be deactivated.

After this, the anti-theft system will work with standard functions.

After turning off the mode, the siren will sound twice, the hazard warning lights will flash twice, and the key fob will emit 2 short “CHIRPS”. The car's headlights will flash 1 time.

Recommendations for use

Valet mode is necessary not only in case of car servicing or repair. It is also suitable for fine-tuning the anti-theft system.

There are several recommendations that will help every car owner use valet mode without the risk of car theft:

• It is important to monitor the status of the function on the key fob display - when it is off, the Z symbol does not light up.
• It is advisable to install the button in a hard-to-reach place that will take a long time to get to. However, its location must be such that the driver himself can quickly use it.
• Do not tell anyone about the location of the button.
• Since the button is small, it should be securely fixed so that it does not fall through.
• The push-button mechanism operates through a traditional connection to the security system, so it is mounted in a place where a standard cable can reach.
• The wire that leads to the Jack button is quite bright, so the driver should disguise it as much as possible.

Taking these recommendations into account, the driver will be able to emergency disable the security system, or set certain settings without the risk of leaving the car unprotected.

However, the vehicle owner himself should remember the subtleties of placing and masking system elements.

The Valet service mode, provided in Sherkhan car alarms, allows you to conveniently manage the functionality of the anti-theft complex. It can be turned on either with or without the key fob.

It is important to remember the possibility of accidental activation of the mode. Following simple recommendations for installing the button will protect your car from theft.

When transferring a car with a Sherkhan alarm system to a service station or car wash, you must disable the security system.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

It is prohibited to give the car alarm key fob to the service center employees, as this increases the risk of car theft. To temporarily deactivate the security system, the car owner should understand what valet mode is and how to turn it on and off if necessary.

Once the valet mode is activated, the alarm will disable most of its functions. In this case, for example, you can lock and unlock the locks of the iron horse using the key fob.

It is not recommended to use this mode for daily use of the car, since in this case the car’s ability to resist theft is minimal.

Magikar 7 autorun settings

Autostart parameters in the Sherkhan alarm system are configured in both the first and second settings menus. The first uses the following functions:

• 9: turns on the “battery warming up” mode before autostart in value 2, turning on the light alarm before attempting to start for 15 seconds. It has no real meaning, it is better to leave it at the factory value (1 – disabled).
• 15: engine operating time at auto start – 5, 15, 25 and 45 minutes.
• 13: autostart interval by timer. In value 1, autostart will occur every day at the time set on the key fob, in values ​​from 2 to 4 - every 8, 4 or 2 hours after activating the autostart mode by timer, regardless of the time setting.
• 14: limiting the number of timed motor starts. As soon as this number is exceeded, the system will automatically turn off the timed start, and the TIMER inscription on the main key fob screen will go out. In options 1-3, a limit is set to 5, 7 and 16 starts, respectively; in option 4, their number is not limited.
• 15: light signaling operation during autostart. The default value is 1 (the light alarm blinks), you can turn it on in constant mode by selecting value 2. Please note that this will only work with power control of the light: if the alarm duplicates pressing the alarm button, and is not connected directly to the wiring of the lamps, then The light will blink anyway.
• 16: autostart backup mechanism for cars with a manual transmission. In option 1, it is necessary to pull the handbrake to intercept the ignition when the engine is running and the doors and hood are closed. This is the default option, and it is also the most convenient. If you do not need auto start at a specific moment, it is enough to tighten the handbrake after turning off the ignition. In option 2, the ignition is intercepted automatically when the key is turned, if the handbrake is pulled out: in this case, there is a small “gap” between turning off the ignition and turning it back on by the autostart circuits. During this time, the engine may stall; you should not use this option. In value 3, this function sets reservation by pressing button 2 on the key fob, if the engine is running, the doors and hood are closed, and the handbrake is applied. That is, every time you intend to use autostart in the future, you will have to manually enable the reservation, otherwise autostart will be impossible.
• 17: How to complete the reservation. In option 1, the engine will stall after the door is opened and closed, but arming will not occur automatically. In option 2, the engine will also stall after closing the door, but the car will be armed. The most convenient mode is 3, when the car stalls only after forced arming - this eliminates the possibility of forgetting the keys in the car.
• 20: limit the number of starts by timer based on battery voltage. Disabled by default (option 1); in option 2, autostart by timer will occur only when the voltage drops below 11.5 V. If temperature triggering is activated at the same time, then this function will not interfere with its operation.
• 21: temperature threshold for timed starts. If you set up a temperature alarm, then Magikar 7 autostart will be possible only if by the time the timer is triggered the next time the temperature has dropped below -15 or -25 degrees (functions 2 and 3) or does not rise above 60 degrees (value 4). In option 1 there are no temperature restrictions.

In menu 2 the following functions are relevant for autostart:

• 12: minimum starter rotation time, 0.6, 0.8, 1.2 or 2 seconds. It is better to set the value to the minimum, ensuring reliable engine starting.
• 13: limitation of starter activation time, if tachometer control is not used. Values ​​are 2, 4, 8 or 10 seconds. It is also necessary to set it to the minimum possible in order to avoid long-term “overexposure” of the starter, which significantly reduces its service life.
• 14: Scroll time increment after unsuccessful startup attempt. In options 1 and 2, each subsequent attempt lasts longer than the previous one by 0.2 and 0.4 seconds, respectively; in option 3, the time is fixed.
• 15: pause between turning on the ignition and cranking the starter. For gasoline engines, value 1 (4 seconds) is sufficient; for diesel engines, select options 2-4 (8, 10 or 15 seconds).
• 21: type of engine control. Please note that for each of them the alarm connection is different, that is, only the setting determined by the installer, or option 3 (based on the voltage in the on-board network), is operational. To use option 1, the signal input is connected to the generator warning lamp, in option 2 - to the tach signal source (analog input of the standard tachometer on the dashboard, injector control signal, and so on). If possible, tachometer control should be used.

During the operation of Scher Khan Magicar security systems, it may be necessary to reflash existing control panels or add new ones. Programming the Sherkhan 7 key fob and other systems of the Magikar family has a simple algorithm and can be performed by the owner independently.

In what cases is it necessary to reprogram the key fob?

Checking the serviceability of the key fob

Instructions for recording key fob codes into the alarm memory

For model 7 and 9

For model 13 and 14

Common mistakes when programming alarm key fobs

How to activate valet on a car

Activation of the “Valet” mode in the Sherkhan 5 auto alarm system is performed by briefly simultaneously pressing the combination of keys I and III. The icon will then appear on the screen

To unlock and lock the doors, the driver should use the I button. When valet mode is activated, the security system actions shown in the table below should be observed.

Table of the security system’s reaction to the activation of the “Valet” mode

Valet activation for Sherkhan 7 is similar to magicar 5, but there are some features:

• the icon indicates that the mode is turned on;
• opening and closing doors can be performed not only with button I, but also with button II;
• there is access to the trunk lock;
• additional channels are allowed;
• key fobs are programmed;
• You can turn on the "Turbo" mode.

Display Sherkhan 7 with activated “Jack” mode
Additionally, magicar 7 and Sherkhan 9 have the ability to activate the “Jack” mode without using a key fob. To do this, follow the sequence below:

• The vehicle must be in the “disarmed” mode.
• Turn on the ignition.
• Press the button on the call sensor body for two seconds.
• Wait for the alarm to flash.
• Briefly press the call sensor button. The pause should not be more than five seconds.
• If necessary, enter PIN 1.
• The warning light should flash twice.
• Within five seconds, briefly press the call sensor key. The system activates the “Valet” mode.

Scher-Khan Magicar: how to turn off without remote control

The Sherkhan Magikar line contains models A, B, 1, 2, 3, 4, 5, 6, 7 S, 8 S, 9, 10, 11, 12, 13, 14, 6 mini, 10 mini. The anti-theft system of this model can be disabled using the factory PIN code.

1. Use the key to open the vehicle door. The alarm mode will go off. To deactivate it, turn the key in the lock three times from “Off” to the “On” position.
2. Within four seconds, turning the ignition on and off, enter the first PIN value.
3. Deactivate the ignition.
4. After four seconds, the lights will flash once, indicating that the next code digit can be entered.
5. Enter the remaining numbers in the same way.
6. A correctly entered password activates the “Valet” mode of the system. The starter is unlocked.

How to disable the “Valet” mode on the “Sherkhan” alarm system

In order to disable the jack mode of scher khan magicar 5, you need to hold down the combination of buttons I and III. The security system will inform the driver that the driver has managed to turn off the mode using the steps below.

Table of events accompanying the exit from “Jack”

In order to disable the Jack Sherkhan 7 function, you need to briefly press keys I and III, similar to magicar 5. Another option is to remove the mode. To do this you need:

• Turn on the ignition.
• Press the button on the call sensor. The duration of the clamping is about two seconds.
• Wait for two short beeps if this function has not been disabled first.
• The alarm will flash twice.
• Full function mode will be activated.

You can exit valet mode when using Sherkhan 9 in the same way as magicar 7. The system reaction is shown in the table below.

"Sherkhan 9" reaction to disabling the "Jack" mode Tired of paying fines? There is an exit! Forget about fines from cameras! An absolutely legal new product - Traffic Police Camera Jammer, hides your license plates from the cameras that are installed in all cities. More details at the link.

• Absolutely legal (Article 12.2);
• Hides from photo and video recording;
• Suitable for all cars;
• Works through the cigarette lighter connector;
• Does not cause interference to radios and cell phones.

Find out more Subscribe so you don't miss anything important Sources used:

• https://avtocity365.ru/avtosignalizatsii-i-protivougonnye-sistemy/chto-takoe-funktsiya-valet-na-signalizatsii-scher-khan/
• https://vidsyst.ru/signalizaciya/avtosignalizaciya/proizvoditeli-avtosignalizaciya/scher-khan/rezhim-valet.html
• https://alarmspec.ru/signalizacii/scherkhan/valet-sherxan.html

Opening a car without a Mobicar key fob

If the Mobicar A, B, 1, 2 alarm key fob breaks down, you can unlock the system using a PIN code. For this.

1. Tap the glass where the call sensor is located ten times. The LED should light up red.
2. The LED started flashing blue frequently, which means you did everything right.
3. Tap the glass to enter the initial digit of the secret password.
4. Enter the remaining PIN values ​​in the same way.
5. If the previous steps are performed correctly, the car doors will unlock and the security mode will be deactivated.

Find out everything about repairing the Sherkhan alarm key fob.

Where is the Valet button?

Scher-Khan security systems do not have a separate Valet button, which puts the equipment into programming mode. On equipment from other manufacturers there is a special switch, which is located under the instrument panel or on the processor unit. To enable the service function on the Sherkhan 5, 7, 10 alarm system, you need to disarm the car, and then briefly press keys 1 and 3 located on the end of the communicator.

After pressing the keys, the car emits a short siren signal, which is accompanied by a flash of external lights. On all car alarms, the control diode located in the signal sensor to the owner lights up continuously. A light signal notifies the driver and service station personnel that the security system is in sleep mode. The icon for the headlights and the security mode status flashes 5 times on the communicator; an additional short signal is given by the buzzer.

It is possible to activate the function on the Magicar 7 product without using a communicator:

1. After the security mode is released, press the call sensor multi-function switch for 2 seconds.
2. You should wait for the lights to flash.
3. After the light signal, a 5-second timer is activated; the owner needs to briefly press the toggle switch. An impulse is given by external lamps, and the control diode goes into rapid flashing mode.
4. Enter 1 digit of the password into the memory of the central unit. Programming is carried out in short pulses, the interval between impacts does not exceed 1.5 seconds. 4 seconds are allotted to enter the number; if the driver does not fit within the time limit, the procedure begins again.
5. Wait for the control diode to blink rapidly, and then program the second register.
6. Using a similar scheme, enter the 3rd and 4th password fields.
7. After entering the last digit, a 5-second timer is activated, the driver briefly presses the sensor button. You can pause for 5 seconds, then the Valet mode will be automatically activated.
8. Wait for the siren to sound, confirming that the Valet function has been activated. Simultaneously with the sound signal, the vehicle's external light alarm is activated.

On the Magicar 5 system, it is possible to enable the Valet parameter during an emergency disarming of the security mode. The driver opens the door and the alarm mode starts at the same time. The key is turned three times in the lock from one extreme position to the other, then the ignition circuit is deactivated. Turning off the alarm is accompanied by the start of a 4-second starter lock disabling timer, then the equipment goes into the “Jack” state.

The additional Valet mode used during the programming process is set by a long complex press on buttons 1 and 4 or 2 and 4. The car will sound a single beep with a siren and flash the hazard lights; the communicator display does not show any additional symbols. Then the car owner makes the necessary adjustments in accordance with the tables and recommendations given in the operating instructions.

Principle of operation

Sherhan brand car alarms have an automatic security activation function that locks the doors 30 seconds after the last limit switch is closed. When handing over the car for service or washing, you must either disable the parameter or leave the keys with the key fob to the employee. There is a special function to temporarily disable the head alarm module of the Scher-Khan Magicar 5, which is activated by pressing the buttons on the key fob.

This Valet mode is displayed on the communicator display with the Zzz icon. When the function is active, it is impossible to enable vehicle protection or program codes for additional transmitters. After the car is released from the service, the buttons are pressed again, activating the normal operation of the complex. This alarm mode is not recommended for everyday use, as it increases the likelihood of car theft.

The Sherkhan 5 alarm system, when the Valet function is active, supports the operation of the central locking; additional channels for controlling the trunk lock are disabled. When activating Valet on Sherkhan 7, it is possible to adjust the operation of additional channels (using buttons on the remote control), and the function of operating the power unit with a supercharger (turbo timer) is supported. The Sherkhan 10 modification uses similar head unit software; the driver controls locks, additional channels and changes the state of the turbo timer function.

VALET mode - service mode of the Alligator S-250 car alarm

The Valet push-button switch is used to enable the Valet service mode (i.e. temporarily disable the security functions of the car alarm). This is necessary, for example, if you need to leave your car at a service station or car service center. At the same time, you will be able to control the service functions of the car alarm (for example, remotely unlock the car doors) and turn on the remote “Panic” mode.

To enable Valet mode:

Note

: When the car alarm is in Valet mode, each time the ignition is turned off, the siren will emit 2 short warning signals.

To turn off Valet mode:

You can also turn off Valet mode remotely using a transmitter (car alarm pager) (see the section “Remotely turning on and off Valet mode” below).

ATTENTION

: Don't forget to turn off Valet mode. This ensures your vehicle is always protected.

Remote activation and deactivation of the Valet mode of the Alligator S250 car alarm

The Alligator S250 car alarm also allows you to turn on or off the Valet service mode (Valet mode is a mode for temporarily disabling the security functions of a car alarm) remotely, using a transmitter. Please note that you will not be able to remotely enable Valet mode while the car alarm is in armed mode, in alarm mode, or if the Anti-Hijack anti-theft function has been enabled (you will need to disable it first).

To remotely enable Valet mode

:

• Get into the car, turn the car ignition on and off;
• After, within 10 seconds, press and hold the button and the transmitter button simultaneously for 3 seconds;
• The car alarm siren will emit one short signal and the LED will start to light continuously, indicating that the car alarm is in Valet mode.

Note

: When the car alarm is in Valet mode, each time the ignition is turned off, the siren will sound 2 short warning signals.

To remotely disable Valet mode

:

• Get into the car, turn the ignition on and off;
• Within 10 seconds, press and hold the button and the transmitter button simultaneously for three seconds;
• The car alarm siren will emit two short beeps and the car alarm LED will go out.

You can also disable the Valet remote mode (car alarm service mode) using the Valet push-button switch (see the “Valet Mode” section above in this text).

What it is

Valet mode or simply service mode is widely used in car alarms of various configuration levels and budgets. When this mode is activated, key functions that perform vehicle protection tasks are deactivated. That is, in fact, the car is not protected. This mode is used in situations where the car is safe; it is impossible to disarm it completely, but it is also not worth turning off the system entirely. A striking example is the transfer of a car to a car service center. By turning on the Valet, the alarm will not go off and the technician will have access to the interior, trunk or engine compartment without any problems. In this case, the keychain remains with you.

If we talk about older models, then there is another purpose for the service mode. Previous security systems implied the need to switch to Valet if it was necessary to configure the system.

Usually, when installing a car alarm that has Valet, a special button is installed. They try to put it in the most accessible place so that an attacker does not have the opportunity to use it and disarm the car.

Never tell anyone where this button is. Even if you leave the car at a trusted car service center.

Valet is found on a fairly large number of security systems designed for vehicles.

In particular, they can be found on the following signals:

• Sherkhan Magicar;
• Sheriff;
• Tomahawk;
• Cenmax;
• Jaguar;
• Pandora;
• Ghost;
• Alligator;
• Starline, etc.

In fact, motorists have two main questions:

• how to remove the mode if it is enabled;
• how to activate it.

Somehow I personally encountered the fact that after activation I stubbornly could not disable Valet on my machine. I had to dig into the instruction manual. The problem was resolved quickly. But I advise you to first look at the instructions from your manufacturer.

Pros and cons of the mode

The key fob communicator allows you to control the Sherkhan alarm system installed in the car at a distance of 1500 m. Data exchange takes place over a radio channel, the information is protected by a “floating” MAGIC CODE, which prevents intelligent hacking, reducing the likelihood of interception and decryption of the signal by a code grabber.

When the “Hands Free” function is enabled on Sherkhan 5, the owner does not need to set the car alarm when going home and remove it from it in order to get behind the wheel. The system automatically tracks the location of the key fob and, when it is removed 5 m (mode 1), puts the car under protection.

Positive aspects of the “Hands Free” mode:

• When unloading the car, when the driver has his hands full with bags or things, there is no need to take out the key fob and activate the security system.
• When a person approaches a car with busy hands from the store or preparing to transport cargo, just pull the handle of the car door or trunk and they will open.
• In unfavorable weather conditions, when it’s frosty or rainy outside, you don’t need to take off your gloves to press the key fob communicator button and stay in uncomfortable conditions longer.

Disadvantages of this mode on Scher-Khan Magicar 5:

• Reduced level of security provided by the security system. When moving away from the car, the car owner leaves the doors open for some time. An attacker can take advantage of this circumstance and steal valuables from the vehicle.
• If a car is parked in the yard and the owner walks past it, it will open automatically without the owner's desire.
• The key fob is in active mode all the time, which leads to rapid battery discharge.

Characteristic “responses” when activating/deactivating the hands-free function

When enabled, the function performs:

• one-time car siren signal;
• single short-term signal from the key fob;
• single flash of alarm;
• on the LCD screen of the key fob the inscription “SV. HANDS". In this case, the headlight and lock icons will blink five times.

When the function is deactivated, the following will happen:

• car siren signal twice;
• double short-term signal from the key fob;
• double flash of alarm;
• on the LCD screen of the key fob the inscription “ST. HANDS". In this case, the headlight and lock icons will blink five times.

This mode can only be used on a switch with an LCD display. The function will not be available on a key fob without an LCD.

When disabling the “Hands Free” mode, one nuance must be taken into account: if the programmed function 1/19 (two-step disarming) is activated, automatic disarming will not occur.

Alarm system Sherkhan 6 (Scher-Khan Magicar) is quite ancient, but can still be found on the shelves of car dealerships.

Sherkhan 6 does not have an automatic engine start, and differs from Sherkhan 5 only in the blue key fob body and the absence of the Absolut 202 launch module in the kit, otherwise the models are completely interchangeable.

If your main Sherkhan 6 key fob is broken, you can safely change it to the Sherkhan 5 model without losing functionality. Also, the case from Sherkhan 5 in gray color fits Sherkhan 6 without any problems

Sherkhan 6 mini (Scher-Khan Magicar 6 mini) the main difference is that the kit does not include a key fob with an LCD display and feedback, only an additional one.

Autostart from the Sherkhan 6 key fob - autostart is possible only if there is a launch module. If such a module is present, you need to press button 2 for 2 seconds. The car doors will close and the engine will start.

Read more: The difference between polyurethane and rubber

The “hands-free” mode is a kind of mode that allows you to determine friend or foe. That is, when approaching a car with the mode on, the car opens on the main key fob, and closes when moving away. With constant use of this mode, the main key fob is disconnected from the system; for it to work fully, it must be re-registered to the car according to the instructions.

The recording of Sherkhan 6 key fobs differs from Sherkhan 5, therefore, if you purchased a key fob from the fifth model, you need to register it according to the instructions for the sixth.

To record key fobs, Hands Free and Valet modes must be disabled.

Disable hands-free mode (if enabled). To turn off the mode, press the key fob button “1” for 2 seconds. Mark under the inscription SV. HANDS will disappear from the display.

Valet mode , if enabled, to exit VALET mode, use a short press of the key fob buttons (I+III).

Recording new key fobs is a little more difficult than for the fifth model, since Pin1 is hardwired into the programming mode, which does not turn off if it has not been changed, the factory value is 1 -1.

How to correctly register the Sherkhan 6 keychain , even if you have a keychain from the 5th model (gray case) in your hands.

Within 4 sec. Turn the ignition key three times from the OFF to the ON position. Turn off the ignition, the hazard warning lights will flash once. If the alarm is not connected to the emergency gang, the relay should click.

After the alarm flashes, turn on the ignition the number of times corresponding to the first digit of the personal code (). The alarm will flash once to confirm that the second digit is ready to be entered.

After the alarm flashes, turn on the ignition the number of times corresponding to the second digit of the personal code (). The hazard warning light will flash once, confirming that the key fob codes are ready to be entered.

After the alarm flashes, press button 1 of the key fob, the code of which must be entered into the memory of the processor unit. To confirm that the code has been recorded, the hazard warning lights will flash 1 time.

If you need to record the code of only one key fob, then briefly press the I button of this key fob three times.

To exit the programming mode, do not take any action for 4 seconds. after recording the code of the last key fob.

The system has three memory cells for storing key fob codes. When you try to record the fourth key fob, the code of the first recorded key fob will be deleted.