If the security equipment is programmed incorrectly, the operation of the automatic or remote start function is disrupted. Resetting the Sherkhan 5 alarm system to factory settings allows you to eliminate the cause of interruptions in operation. The driver then re-sets the parameters, taking into account the design features of the vehicle and additional equipment.
How to remove ZZZ on Magicar?
How to disable ZZZ on Sherkhan 5? Simultaneously press buttons I and III of the key fob and hold them for two seconds. Pressing this combination allows you to remove the service mode, which disables the security system.
Interesting materials:
What moon is May 2022? What is the bookmaker's margin? Which matrix is better than IPS PLS? What pneumatic power is allowed? What is the wattage of the monitor? What is Gazmanov's real name? What is Austria's nationality? What bait for grass carp? What is the amount of cottage cheese per day? Which RAM is better DDR3 or DDR3L?
How to reset settings
Resetting the settings of Sherkhan security systems (starting from the Scher-Khan 3 modification) is performed using the buttons located on the key fob. Since alarms use a programming table consisting of 2 sections, the operation is performed in 2 stages. The equipment design does not provide for a procedure for simultaneous zeroing of all parameters.
Some security systems use a method of resetting values using a programming button or entering a numeric password. In early modifications (for example, Magikar 2), the operation is performed using a series of 2-position switches located on the rear wall of the case. Returning to factory settings involves moving the toggle switches to the “off” position.
Menu No. 1
To reset the first table (programmed by the key combination “1” and “2”), you must:
- Enter the function adjustment mode by holding down buttons “1” and “2” for 2 seconds. If the command is executed correctly, the horn or siren is activated once, and at the same time a flash is given by the external lighting equipment (connected to the security equipment).
- Perform 3 short-term consecutive impacts on the “3” key. Each time the siren should sound a short beep and the external lights should flash.
- Wait until 5-7 seconds have passed after the third press: the delay is necessary to automatically return the values to the factory settings. Confirmation is a triple short signal from the lamps, supplemented by a triple activation of the siren.
Menu No. 2
The second table is cleared using a similar algorithm; to call the programming mode, press the “2” and “4” buttons for 2 seconds. The procedure is standard for Magikar alarms A, 5, 6 or 7. In the Jungle or Vegas modifications, a common programming table is used, which is deleted using 2 methods (depending on the initial programming of the central unit).
To remove values without using code, you need to follow these steps:
- After activating the ignition, press the Valet switch three times within 5 seconds.
- After flashing the light signal, press the button 3 more times (the interval between impacts ranges from 1 to 3 seconds).
- Wait the 3 seconds required to delete the settings.
If the owner has set the reset using a password, then after turning on the ignition, the first digit is entered (by pressing the switch). Then the driver waits 3 seconds, after the lighting lamps flash, the second character is dialed. If the password is correct, a single flash occurs; if an error is made, the lamps will blink twice. There are 3 attempts to enter the code; if all the numbers are incorrect, a 30-minute timer is activated, blocking the password request function.
After receiving confirmation that the code is correct, the Valet button is pressed three times. The alarm design allows an interval between presses in the range from 1 to 3 seconds. Each operation is accompanied by the operation of lighting lamps. After a 3-second pause, during which it is prohibited to press the communicator keys, the settings return to their original settings. Confirmation is a triple flash of lamps.
- How to disable Valet mode on Sherkhan Magikar 5 alarm system
- Alarm Sherkhan Magikar 5 does not respond to the key fob
- Magikar 5 installation instructions
- How to reset a Starline alarm
Resetting values for programmable functions from menu No. 2
The principle of operation will be similar, only to enter menu No. 2 you need to hold down for at least 2 seconds. key fob buttons numbered I and IV. Performing this action will result in short alarms with light and sound. They confirm that the login was successful.
Next, reset the settings like this:
- Press the key fob button III for 0.5 seconds three times.
- Wait for a short emergency flash signal and siren.
- Wait for reset confirmation. This will happen after a short time. Confirmation will be a three-time siren sound and a three-time flash.
The reset procedure is not difficult. But professionals do not recommend doing it yourself. The reason for this is the possible and unpredictable failure of various components of the car - it is impossible to start the engine, turn on the security mode, etc. It is better to entrust this procedure to a professional installer.
Scher-Khan Magicar V - instruction manual
Scher-Khan Magicar V is one of the previous generations of the popular alarm system, combining security, monitoring and functions that improve the performance of the car.
Scher-Khan Magicar V is one of those types of car alarms that have feedback via a control key fob. The Scher-Khan Magicar V alarm system is controlled remotely using a key fob with a display located on it. The control key fob allows you to remotely control the alarm functions using several keys on the key fob (I, II, III, IV), various combinations of buttons and press lengths - short presses (0.5 sec) and long presses (2 sec).
Resetting values for programmable functions from menu No. 1
ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"
SCHER-KHAN machine security systems differ in functionality, but not in control principle. Therefore, the instructions for resetting the settings will be the same for both the popular model Sherkhan Magikar 5 and for devices of earlier and later releases.
- Press buttons (the purpose can be found in the instructions) I and II simultaneously.
- Hold them for at least 2 seconds.
- Wait for a short single sound and light signal. The device will perform them once. Sound and light signals make it clear that the user has successfully entered menu No. 1 of Sherkhan 7 or another SCHER-KHAN model.
- Hold button III for 0.5 seconds (short hold). Carry out the procedure three times.
- Pay attention to short signals with light and sound from the device each time you press it. There definitely must be.
- Wait until the alarm emits three consecutive light and sound alarm signals.
The last point is performed after a short time of 7-15 seconds. They symbolize that the factory reset of functions from the programmable menu was successful.
Adjusting the shock sensor
The impact sensor notifies the car owner about an incident with the car while the car is parked with the alarm on.
Scher-Khan Magicar V alarm sensors are two-level: with a weak impact, a beep sounds 4 times and the alarm flashes 4 times. If there is a strong impact, the key fob goes into alarm mode, lasting 30 seconds - 30 flashes of the emergency lights and 30 short beeps. Shock sensors can be turned on or off by pressing the combination of buttons I and III and holding them for 2 seconds.
Adjusting the impact sensor helps to avoid false alarms of the accident warning sensor, since with a sensitive sensor, even the passage of a neighboring car can be falsely perceived by the system as an emergency impact. To adjust the sensitivity of the sensors, physical access to them is required; you can find out about the location of the shock sensors at a service station. There are regulators installed on the sensors themselves; turning clockwise increases sensitivity, counterclockwise turns it down until the sensor is completely turned off.
How to turn off the alarm?
To disable the security alarm functions, the system provides a special VALET mode. The shutdown function is necessary, for example, when taking the vehicle to a service station to prevent the alarm from going off. To switch to VALET mode, just briefly press keys I and III. You can also turn on the mode with the ignition key - just as when registering a new key fob, you need to turn the key in the cell three times from the OFF position to the ON position, that is, enter the programming mode. In the future, do not take any action for 4 seconds, after which the system will automatically switch to VALET mode.
In VALET mode, the function of opening/closing doors is retained, for which you need to briefly press button I. You can exit VALET mode by pressing the combination of keys I and III.
How to register a key fob?
The Scher-Khan Magicar V alarm system can “remember” 3 different key fobs. To synchronize a new key fob with an alarm system you need to:
- turn the ignition key three times from the OFF position to the ON position - the “hazard light” should flash once, confirming entry into the programming mode;
- no later than 4 seconds after the flash, you need to press the I key on the new key fob;
- Next, you need to enter the key fob code into the memory of the alarm processor unit.
The memory of the processor unit can store data from only 3 key fobs, so when registering the fourth key fob, the code of the first is deleted from memory.
You can exit the programming mode without taking any action for 4 seconds after recording the last digit of the code.
Engine starting
The Scher-Khan Magicar V alarm allows you to start the car engine using the control key fob. To do this, press button II of the key fob and hold it for 2 seconds (long press). In this mode, the alarm goes into security mode, the car doors are locked, and the engine starts. The duration of the motor operation can be programmed for different time periods:
Starting the engine is accompanied by several indicators confirming the successful execution of the request:
- siren signal
- sound signal from the key fob;;
- flashing of the emergency lights;
- The headlights light up 5 times on the key fob display
If starting the engine fails, the system will repeat attempts a maximum of 2 more times. If after this the engine still fails to start, the alarm goes into normal mode.
In order to start moving the car, the driver, with the engine started from the key fob, needs to open the doors, insert the ignition key and turn it to the ON position. To do this, the driver has 20 seconds after opening the doors. If during this period the key is not turned to the desired position, the system will automatically turn off the engine.
The alarm may not start the engine for several reasons:
- the engine is already started;
- the ignition is already on;
- doors or trunk are open;
- The reservation mode has not been completed for vehicles with manual transmission (the control lever has not been moved to the neutral position).
Therefore, in order to automatically start the engine, the driver of a car with a manual transmission must first, after stopping:
- set the gearbox lever to the “Neutral” position without turning off the engine;
- close the hood and trunk;
- press button II on the key fob;
- turn the ignition key to the off position and pull it out (the engine will continue to run);
- get out and slam the door (the engine will stall).
Setting the time on the key fob
Setting the exact time on the key fob display is a necessary procedure in order to be able to start the car engine using a timer in automatic mode. Since the exact time is reset when the power is turned off, the installation is carried out not only before starting operation, but also when replacing the battery.
Setting the exact time on the key fob consists of several stages.
- You need to press the combination of buttons II and III. Pressing duration is 2 seconds. After this, the programming mode is entered, about which the owner is notified by the sound signal of the key fob, the flashing of the alarm and a special symbol on the display.
- Next, press the I button and hold it for 0.5 seconds. This activates the mode for setting the exact time, confirmed by a sound signal. The device display shows the current time flashing.
- Next, the exact time is set. Using button I you can change the hours, and using button II you can change the minutes. To change one step, you must hold the desired key for 0.5 seconds.
- The last stage is exiting the programming mode, which is carried out by pressing the combination of keys II and III. Exit from the mode is confirmed by a sound signal.
Autorun programming
The Scher-Khan Magicar V alarm allows you to automatically start the engine in various modes:
Starting the engine every 24 hours allows you to start the engine at the same time every day, which is convenient, for example, for warming up in the morning. Starting every 2 hours allows you to maintain the temperature of the engine and interior on cold days or, conversely, cool the interior in the summer season. Both timer modes cannot be used simultaneously. The autorun mode is selected through the programmable functions menu.
To program autostart every 2 hours, you need to briefly press buttons II and IV. In this case, the engine will automatically start 2 hours after pressing. In this case, setting the time is not required.
Factory reset
Errors in self-programming of alarm functions may require a rollback to factory settings. Resetting programmable alarm functions to factory values is carried out in 2 stages.
- At the first stage, you should enter the programming mode - press buttons II and III simultaneously and hold them for 2 seconds.
- In the second step, you need to press button III on the key fob three times (0.5 seconds each). Each press is accompanied by the flashing of the emergency lights and a sound signal. After a short period of time, 3 beeps should sound, and the hazard warning lights will also flash three times. In this way, the owner is notified that the function programming settings have been reset to the “default” settings.
