Instructions for programming alarm key fobs Sherkhan Magikar

The breakdown has nothing to do with the car. So in January, button II (responsible for opening) on ​​my main alarm key fob failed. When I took it apart I saw that the microphone had broken off from the board:

I ordered a new one from Ali for 1054 rubles, in Tomsk there are 1500-1700 rubles. Last week a new keychain arrived from China:

Then I got my hands on the key fob, but I can’t link it to the alarm. I found information specifically about Sherkhan 5: PROGRAMMING NEW KEY FOBS The system can remember the codes of three key fobs. Follow two steps to program new key fobs. Turn the ignition key three times from the OFF to the ON position. The alarm will flash once to confirm entry into programming mode. No later than 4 sec. after the alarm flashes, press button I of the key fob, the code of which must be entered into the memory of the processor unit. To exit programming mode, do not take any action for 4 seconds. after recording the code of the last key fob. If after step 1 you do not take any action, then after 4 seconds. the alarm will flash 2 times, the system will switch from key fob programming mode to VALET mode. Note: the system has three memory cells for storing key fob codes. When you try to record the fourth key fob, the code of the first recorded key fob will be deleted.

As I understand it, there is no separate valet button on the 5 Sherkhan, turning the key three times as written above does not give anything. I found the whitefish itself under the tidy, when I soldered the Led pin, I removed it.

Most likely some kind of handyman installed the alarm, everything there is twisted. It looks like you need to look for a diagram, see what you screwed where.

Programming the Sherkhan 5 key fob may be needed in the following cases:

1. The alarm does not turn on or off from one remote control, others work fine.
2. Damage to the switch housing or circuit board.
3. Incorrect operation of the main unit and remote control.
4. Use of additional key fobs.

Three pagers can be stored in the anti-theft system's memory. This is not difficult to do, but the procedure has its own characteristics.

Linking a new key fob to the Scher Khan Magicar 5 alarm system

The instruction manual will help you to record a new communicator into the memory of Magikar 5. Please read it carefully before performing any operations with the remote control.

You can program the anti-theft system key fob only when the security mode is disabled. If you connect new remote controls, do not forget to overwrite the old ones, otherwise they will be deleted from the system memory.

1. In four seconds. turn the ignition on and off three times. The lights will flash once. The programming mode has been entered.
2. Enter the remote control code by pressing button 1. This must be done within four seconds. The vehicle's lights will light up once.
3. If necessary, record the following switches in the same way.
4. Do nothing for four seconds after programming the last remote and the system will automatically exit settings.

Keychain - communicator

Features of Sherkhan Magikar 5 car alarm with auto start: installation and operating instructions

Before using the remote control, you must install a power source into it.

To do this, remove the protective cover from the back of the communicator into which the battery is inserted, observing the correct polarity. After this, the lid closes.

Indicator designation

Labels of buttons on the remote control display

Description of symbols on the communicator screen:

• A - operation of the power unit by timer;
• B — turbo timer option;
• C — passive security activation mode;
• D — option to automatically activate security without clicking on the keys;
• E - activated siren;
• F—sensitivity controller disabled;
• G—the communicator has the vibration alert function enabled;
• N - control of door locks after activation of the ignition system;
• J - open luggage compartment door;
• K - the power unit is started in automatic start mode;
• L — state of the anti-theft installation;
• M - open door locks;
• N - information field for displaying clock data, as well as temperature conditions during automatic start;
• О — Valet service mode is enabled;
• P - the car has a light alarm or the side lights are not turned on;
• Q - activation of the sensitivity controller;
• R—communicator power supply icon;
• S—signal level.

Main functions of the key fob

To adjust basic parameters and set functions, use the button combinations shown in the table.

How to get the key fob into working condition?

The procedure for binding a new communicator is as follows:

1. The key is inserted into the lock, after which the ignition is turned on and off three times. The light alarm should sound once, indicating that you have entered the setup mode.
2. Over the next four seconds, you must click on the first button on the communicator.
3. Then the pager code is entered into the memory of the microprocessor module.

The car owner can register no more than three communicators. Therefore, when setting up the fourth device, information about the first is deleted from the microprocessor memory. To exit the settings mode, you must not touch the key fob for four seconds.

The MasikBonLive channel talked about independently linking a new communicator to a microprocessor alarm module.

Firmware and reprogramming Sherkhan 5

You can reflash the Magikar key fob version 5 using the PIN code. Record the remote control codes by following the instructions below.

1. In four seconds, turn the ignition key three times from the “Off” to “On” position. Turn off the ignition.
2. Turn the ignition back on within four seconds. The number of activations must match the first value of the secret code. The light optics will light up once, confirming that the second value can be entered.
3. Turn on the ignition. The number of activations must correspond to the second digit of the code. The emergency light will blink once, confirming correct action.
4. Enter the remaining secret number values ​​in the same way.
5. After entering all the numbers, press button 1 of the switch. The lights will light up once to confirm the pager entry. After four seconds, the system will exit programming mode.

Setting up Sherkhan Logicar 1

All actions are performed with the protection mode turned off. To sync your Logicar 1 pro 2 remote control, do the following.

1. Turn off the ignition if it is on. Press and hold the key located on the body of the diode element for two seconds. The lights will flash once.
2. Within five seconds. Press the key a second time. If no password is used, the turn signals will light up twice. If there is a code - 1 time.
3. Enter your PIN if you use one. The hazard warning light should blink twice.
4. After 5 sec. The LED will light up continuously. This means you can register a new key fob. Three remote controls can be activated in the memory of the Logicar security system.
5. Within five seconds, press the first key on the pager. The installation procedure for the remaining switches is similar.

The additional Magicar 5 key fob is not registered: reasons

There are often situations with the anti-theft system communicator when it is not programmed. There are a number of reasons for this:

• the remote control is damaged;
• “Valet” mode is activated;
• The system does not recognize the “Ignition on” command.

If you are unable to register the key fob on your own after trying all the options, you should replace it with a new one or contact the service src=”https://daciaclubmd.ru/wp-content/uploads/2018/12/peyterka-2.jpg” class =”aligncenter” width=”600″ height=”320″[/img]

MAGIGAR 5 INSTALLATION ON ENGINE WARMING UP KEY FOB, MORE THAN 5 MINUTES

Good day to all. Please tell me, who uses such a device, what buttons need to be pressed on the key fob so that the engine, when started remotely to warm up, is programmed to run for more than 5 minutes?

I downloaded the manual, it’s 80 pages long, but I couldn’t figure it out.

Thanks in advance to anyone who can provide information on this issue.

Last edited by Vl; 11/16/2015 at 06:34.

Everything about Magikarov needs to be merged into one topic. there's been a lot of this in recent days...

Thank you robot for your efficiency. I retyped it, I’ll try it (now the car is warming up from the pre-start heater) Then I’ll post what happened

Setting up Sher Khan 5 autorun

Button pressing modes (not to be confused!):

1. A short press
   is a single press lasting no more than 0.5 seconds, accompanied by a short sound signal.
2. A long press
   is holding the button pressed for more than 2 seconds. - until a beep appears, then you can release the button.

You only need to change 3 functions:

• 1-12 engine operating time (5min/15min/25min/45min)
• 1-13 start frequency (24h/8h/4h/2h)
• 1-21 start temperature threshold (no/-15/-25/+60)

Before programming, you need to remove the car from the alarm and open/close the driver's door (so that the alarm doesn't go back on during programming), and you also need to be in or near the car. An example of programming the engine operating time (function 1-12) for 25 minutes:

1. Entering programming mode No. 1: press buttons I and II simultaneously - hold until the remote control emits a signal. The alarm will go into programming mode.
2. We successively perform short presses of the IV button as many times as required for the selected program. In our case, we need to press 12 times. Each press will be confirmed by signals from the key fob and the car. After you press the IV button the required number of times, you need to pause for 2-4 seconds, after which the alarm will sound sequentially, confirming the number of the programming item (12 times).
3. Then you need to press the button once in accordance with the required value: (example: I - 5min, II - 15min, III - 25min, IV - 45min)

After this, the alarm will exit the programming mode. If you make a mistake at any step, you will have to repeat everything from the beginning. So, to configure Sherkhan 5 to autorun every 2 hours

or
when the temperature in the cabin drops to -15
and with
a warm-up time of 25 minutes,
you need to perform the following steps:

1. function 1-12 - set to 25 min (III). (I+II)—; IV(12 times); III
2. Function 1-13 is set to 2 hours (IV). (I+II)—; IV(13 times); IV
3. function 1-21 is set to the value -15?С (II) (I+II)—; IV(21 times); II

everything worked out, the second time I programmed the engine to warm up for 15 minutes. Now I’m thinking about finding a temperature sensor in the cabin and connecting it directly to the engine. And then it turns out weird, the car started up unattended and what happens there. And after looking at the engine warm-up temperature, you will feel better about the condition of the equipment. The temperature sensor is probably easier to install in the heater air duct.

and thanks again to everyone who helped solve the problem.

Autorun setup instructions

Starting the engine is a very convenient function of the security system. After carefully studying the instruction manual, every car enthusiast can start the car using the key fob. Before programming, disarm the car, turn off the ignition, turn off the hands-free mode, and open one door just in case.

Time setting.

1. To enter programming, simultaneously hold down keys 1 and 2.
2. Enter the timed autorun settings by pressing button 4 thirteen times. After each press, the system should emit a single beep.
3. Select the desired autostart time: button 2–8 hours, 3–4 hours, 4–2 hours.
4. Then turn on the timer by clicking keys 2 and 4 simultaneously. The “timer” symbol will appear on the display.

Automatic engine start based on temperature.

1. Enter programming mode: buttons 1 and 2.
2. Press key 4 twenty-one times.
3. Select the required temperature: key 2 – (-15), 3 – (-25), 4 – (+60).
4. Turn on the timer by pressing 2 and 4 simultaneously. The display will show “timer”.

Where is the Valet button?

Scher-Khan security systems do not have a separate Valet button, which puts the equipment into programming mode. On equipment from other manufacturers there is a special switch, which is located under the instrument panel or on the processor unit. To enable the service function on the Sherkhan 5, 7, 10 alarm system, you need to disarm the car, and then briefly press keys 1 and 3 located on the end of the communicator.

After pressing the keys, the car emits a short siren signal, which is accompanied by a flash of external lights. On all car alarms, the control diode located in the signal sensor to the owner lights up continuously. A light signal notifies the driver and service station personnel that the security system is in sleep mode. The icon for the headlights and the security mode status flashes 5 times on the communicator; an additional short signal is given by the buzzer.

It is possible to activate the function on the Magicar 7 product without using a communicator:

1. After the security mode is released, press the call sensor multi-function switch for 2 seconds.
2. You should wait for the lights to flash.
3. After the light signal, a 5-second timer is activated; the owner needs to briefly press the toggle switch. An impulse is given by external lamps, and the control diode goes into rapid flashing mode.
4. Enter 1 digit of the password into the memory of the central unit. Programming is carried out in short pulses, the interval between impacts does not exceed 1.5 seconds. 4 seconds are allotted to enter the number; if the driver does not fit within the time limit, the procedure begins again.
5. Wait for the control diode to blink rapidly, and then program the second register.
6. Using a similar scheme, enter the 3rd and 4th password fields.
7. After entering the last digit, a 5-second timer is activated, the driver briefly presses the sensor button. You can pause for 5 seconds, then the Valet mode will be automatically activated.
8. Wait for the siren to sound, confirming that the Valet function has been activated. Simultaneously with the sound signal, the vehicle's external light alarm is activated.

On the Magicar 5 system, it is possible to enable the Valet parameter during an emergency disarming of the security mode. The driver opens the door and the alarm mode starts at the same time. The key is turned three times in the lock from one extreme position to the other, then the ignition circuit is deactivated. Turning off the alarm is accompanied by the start of a 4-second starter lock disabling timer, then the equipment goes into the “Jack” state.

The additional Valet mode used during the programming process is set by a long complex press on buttons 1 and 4 or 2 and 4. The car will sound a single beep with a siren and flash the hazard lights; the communicator display does not show any additional symbols. Then the car owner makes the necessary adjustments in accordance with the tables and recommendations given in the operating instructions.

How to remove Valet mode without a key fob

On the Sherkhan alarm system, it is quite easy to turn on the “Valet” mode by accidentally pressing it. Very often this is mistaken for a system failure: the alarm does not respond to blows, autostart fails, key fobs are not programmed, the LED is constantly on. Only the central locking and trunk opening work.

To disable Valet without a key fob, use the multifunction button located in a visible place.

1. Turn on the ignition, do not start the engine.
2. Press and hold the multifunction key for two seconds. "Jack" is disabled.

Enabling security mode

The Sherkhan Magikar 5 alarm system is configured in accordance with established rules. First of all, experts recommend mastering the security regime. To do this, you need to turn on the alarm. All car doors must be properly locked. The glass should be raised all the way. The driver must check that the trunk and hood are closed.

If all the doors and windows in the car are tightly closed, the user presses the first button on his main key fob. The locks should lock at this moment. It also eliminates the possibility of the starter working. The Sherkhan Magikar 5 alarm key fob will emit a special signal. The siren will also produce the sound specified by the program. The car should turn the headlights on and off 5 times.

The indicator in the cabin will light up. If it flickers with a certain frequency, this indicates that the security mode has been successfully activated. The frequency of the LED light signal should be once per minute.

If the driver does not close the doors tightly, does not raise the windows completely, or the trunk is open, the key fob will beep 3 times. The siren will also emit 3 beeps. This needs to be monitored closely. If the indicator does not light up, then you need to check the operation of the system. This will avoid troubles in the future.

Are all Sherkhan Magikar 5 keychains interchangeable?

The alarm remote control is something that is constantly lost, forgotten, broken, or falls into the water. It is not possible to connect a second key fob due to its absence. Replacing with the original remote control is also unrealistic. You have to look for a communicator from a family that is more or less compatible with yours. The pager may be completely, partially, or not suitable at all. We reviewed the compatibility of key fobs for the Sherkhan Magikar 5 anti-theft system earlier.

Main characteristics

The Sherkhan Magikar 5 car alarm, the instructions of which must be studied by the user before starting work, is a popular anti-theft system. It is known for its versatility and reliability. The alarm software is compatible with almost all gearboxes installed in modern vehicles.

Experts say that this is one of the most reliable and efficient systems on the automotive market today. "Sherkhan Magikar 5" is created on the basis of two-way communication with the vehicle. Information about its status is displayed on the display of the liquid crystal key fob. A clear interface and easy setup allow the user to fully control the state of their car’s systems.

The Sherkhan Magikar 5 alarm system, the instructions for which will allow you to fully use the existing functions, has a whole list of built-in programs. They improve the safety of the car, the driver and all road users. Some programs increase the operating comfort of the vehicle. These primarily include the autorun function. However, this is far from the only program that increases driver comfort.

Each vehicle owner can choose a specific set of commands for himself. To do this, it is important to carefully study the instructions, as well as the advice of experts. This will allow you to select the most suitable list of system functions.

Meaning of icons

Before you start programming the Sherkhan key fob, you need to find out what the icons on the display mean and what they are intended for. Key icons on the screen are used for the following notifications:

1. Indication of the functionality of the communicator transmitter.
2. Indication of the current battery charge level.
3. Indication of the clock, on-board voltage, temperature in the cabin, warm-up timer during autostart.
4. Indication of door lock status.
5. Security mode indication.
6. Indication that the shock sensor is turned off.
7. Vibration alert indication.
8. Indication of central locking control by ignition.
9. Indication of the “driver call” option.
10. Alarm indication when the shock sensor is triggered.
11. Indication of turned on side lights.

Expert reviews

The Sherkhan Magikar 5 signal has a lot of advantages. High technology and ease of operation make it in demand. Experts say that when installed correctly, this system has a high level of reliability. All its sensors have a special protection class. The antenna and processor are also completely protected from unauthorized access to the software. If desired, you can install the system yourself. However, experts say that this increases the likelihood of the user making a mistake. This compromises the reliability of the equipment.

There is a loud siren installed in the engine department. It has virtually no malfunctions. All system components were manufactured using the latest scientific developments. Thanks to the unique standards that were used in the development and creation of the alarm system, Sherkhan Magikar 5 is considered one of the most high-tech, intelligent security systems. During the manufacturing process, all components are tested at all stages of production. This allows for high system reliability.

"Sherkhan Magikar 5", the price of which is about 5-6 thousand rubles, belongs to the middle segment of security products. This product is available to almost everyone. You can separately purchase a key fob with an LCD display for 1.2-1.4 thousand rubles. They are also sold separately with removable covers. Their cost is about 300 rubles. They help protect the remote control from scratches. The availability of additional elements of the presented alarm system allows each car owner to update his security system if necessary.

Purpose of the buttons

Having familiarized yourself with the display icons, you can begin to understand what the control buttons on the key fob mean:

1. Pressing button 1 for 0.5 s is used to: turn on security modes, deactivate the siren, turn on the starter, lock the locks.
2. Pressing button 2 for 0.5 s turns off the security modes, pauses the alarm mode, turns off the lock and opens the locks.
3. Using button 3, held for 0.5 seconds, you can turn the screen backlight on or off.
4. Button 4 is used to check the status of the security system.

Beginning of work

The Sherkhan Magikar 5 alarm system, the installation and operation of which must be carried out exactly according to the manufacturer’s recommendations, is considered a simple, understandable system. Before starting work, you must carefully study all the provisions of the instructions. Experts recommend immediately highlighting those functions that will be used by the driver. This will simplify the process of remembering and managing the device. Having completed this task, you can begin working with the security system.

First of all, you need to insert the battery into the remote control. It comes complete with a keychain. After installation, you can turn on the remote control. It has 4 buttons and a display. The set of functions includes vibration alert and automatic backlight. The screen displays information about the state of charge of the battery and temperature indicators inside the car.

By pressing certain combinations of the available 4 buttons, you can set various commands to the control unit. The signal transmission encoding is highly reliable. She is unique. Any other remote control, even from a similar system, will not be able to control the car alarm.

The key fob must be linked to the system. The delivery package may also include additional key fobs. They also need to be registered in the program memory. Moreover, this procedure is performed simultaneously for all remote controls. You can rewrite if necessary.

Firmware and reprogramming

Programming the Scher-Khan Magicar 5 key fob is relatively easy. If flashing is necessary, it is better to use a PIN code and follow the following instructions:

1. Within 4 seconds, turn the ignition key three times to different positions, and then turn off the circuit.
2. Within the next 4 seconds, turn the ignition on again. It is important to ensure that the number of turns matches the secret code value. If everything is done correctly, the alarm will make a single light notification, which will confirm the possibility of entering other symbols.
3. Turn on the ignition. The number of presses must correspond to the second digit of the code - if everything is correct, the emergency light will blink once.
4. Using a similar principle, activate the remaining code values.
5. When the code is entered, all you have to do is press 1 button on the pager and wait until the indicator lights blink once, indicating that the results have been successfully saved.

Following these instructions, you can reflash the alarm key fob in a couple of minutes.

User guide

Programming key fob tomahawk x5

The system comes complete with an instruction manual in Russian, which outlines all the design features of the Scher Khan Magicar 5 system, tips for setup and use.

PIN Programming

To configure the code you need:

1. Turn on the ignition and open the driver's door.
2. Hit the call sensor ten times with slight force, with a break between blows of no more than 1.5 seconds. When there is an impact, the sensitive element in the sensor will begin to signal by turning on the green diode.
3. After the last hit, the diode will start flashing red. If this does not happen, then errors were made in the procedure and it should be started again.
4. If the diode is turned on normally, it is necessary to strike the sensor several times (the number corresponds to the first digit of the code). Wait until the number is confirmed by flashing the diode (red, turns on 1.5 seconds after the last strike).
5. After confirmation, the diode will return to its previous flashing mode. At this time, the second digit should be entered.
6. The third and fourth digits are entered in the same way.
7. After recording the last digit, the system will give a single short signal with a siren and an alarm.

How to open a car using a code?

In order to open the car by entering a code, you will need:

1. Apply ten light blows to the sensor at intervals of no more than 1.5 seconds. Each blow should cause the green diode to blink briefly.
2. Wait until the red diode starts blinking and apply the number of blows to the sensor corresponding to the first digit of the code. Confirmation of the correctness of the input will be flashes of a red diode with a different frequency. After this, it will switch to private flashing mode, which is a signal to enter the second digit.
3. Enter the rest of the code data in the same way. If the entry is successful, the system will turn off and the door lock will be unlocked. If an error occurs, the procedure must be started again.

Magikar 5 allows only five input attempts within 30 minutes. After this, the system is blocked for a day and can be turned off during this period of time only by a signal from the key fob.

Enabling security mode

In order to put the electronic system into operating security mode, you must briefly press the first button on the main or additional key fob. When setting, the turn signal lamps turn on and a short signal is given by the siren and buzzer of the key fob. A closed lock icon is displayed on the screen. The shock detection sensor turns on half a minute after the system is turned on.

Enabling security using key fobs

It is possible to disable the security by pressing the first button of any of the key fobs, which will produce a double alarm with lamps and a siren. The icon (open lock) will change on the display.

Deactivating the alarm from the key fob

The system can operate in passive mode, when security is activated half a minute after all doors and covers on the body are closed. If the doors do not open when the system is turned off, it will automatically arm. To use the passive mode, it should be activated by briefly pressing the second and third buttons of the main key fob.

Passive operating mode is active (the Passive icon is lit on the display)

If the doors and trunk lid were opened and closed, the system will turn on the protection half a minute after the lock of the last element is latched.

How to program a new key fob

To configure the new Sherkhan key fob without errors, you must follow the instructions exactly. First of all, it is worth installing batteries in the pager, having first removed the special compartment behind the cover. To remove the cover, you will need to slide the latch.

The new key fob is registered according to the following principle:

1. The ignition is activated three times and turned off by turning the key in the lock to the “Off” position. It is important for the driver to carry out these manipulations within 4 seconds. Otherwise, you will have to repeat the steps again.
2. When the light indication works, you need to press button 1 on the key fob. The interval between pressing and blinking should not exceed 4 seconds. If the communicator is paired successfully, the signal lights will blink 2 times.
3. The rest of the new key fobs are registered in exactly the same way. To exit the settings mode and save them, just do nothing for 4 seconds.

If an additional key fob is not registered

If attempts to program the key fob are unsuccessful, you need to check the device for faults, taking into account the following guide:

1. Try to get into the salon using the main remote control.
2. If the security system does not respond to commands from the main key fob, you need to use an additional one. If problems arise far from home, turn off the system using the emergency method, i.e. entering a secret code. When you return home, you need to check the alarm with a second remote control.
3. If there is no response to the second pager, make sure the transceiver is working properly. Re-register the key fobs. If this does not solve the problem, contact a service center for help and carry out a comprehensive diagnosis.

Sherkhan key fobs with one-way communication standards are equipped with control diodes. Their performance can be determined by the presence of a light indication.

At home or in a workshop, the possibility of transmitting a signal is determined by a tuned radio receiver that receives waves in the range of 280-450 MHz. Depending on the intensity of the sound produced by the remote control, the current state of charge of the batteries is determined. The role of the antenna is performed by a loop of copper wire.

To check the device, you must:

1. Place the keychain on the top.
2. Press the button that produces a signal.
3. Change the orientation of the key fob by rotating the variable capacitor handle. This will allow you to achieve high sound quality. If desired, the capacitor is equipped with a scale of operating frequencies, made using the example of a working device.

After checking the signal level, you can dismantle the device to check the condition of the keys and other operating elements. If visual defects are noticed, including loose legs or peeling, they will need to be re-soldered. Parts with mechanical damage are replaced with similar new ones.

How to install?

In accordance with the operating instructions for the Sherkhan Magikar 4 car alarm, the installation of the anti-theft system should be carried out on a car with the battery disconnected.

Magicar 4 Installation Guide:

1. The control unit is placed in the cabin, in the driest and most protected place. For mounting, a flat surface located behind the instrument cluster is used. Thanks to this, the user does not have to extend the wires for connection.
2. The transceiver with antenna is installed on the inner surface of the windshield. A car owner call sensor can also be placed next to the device. For fixation, use a sticker, which is included in the package, or glue. Do not place electronic equipment or metal products near the transceiver as this will result in poor signal transmission.
3. The siren is mounted in the engine compartment; to mount it, holes are drilled in the body, which will allow the bracket to be fixed. This device must not be installed on the cylinder block or metal surfaces adjacent to it.
4. The service mode entry button is installed in the cabin, in the most hidden way. During installation, it must be taken into account that the user must have free access to the key from the driver’s seat.
5. The shock sensor is installed in the central part of the body, for example, on the partition separating the engine compartment from the passenger compartment. For fixing, a flat surface is used; fastening is carried out using self-tapping screws or plastic clamps.
6. The LED indicator is installed on the instrument panel, inside the car. After installation, the cable is laid from the device to the control unit.
7. If you plan to use a temperature sensor, you will need screws or plastic ties to secure it.

Connection procedure

Features of connecting the main 8-pin connector of Sherkhan Magikar 4:

Wiring diagram of the 8-pin block CN 1 Sherkhan Magikar 4

Connection diagram

Connection map of the microprocessor module with other elements of Magicar 4:

1 part of the electrical circuit 2 part of the connection map 3 part of the microprocessor connections 4 part of the connection diagram

Instructions for setting up autorun

Automatic engine start is one of the most useful functions of all Sherkhan alarms, so every driver needs to know how to set up autostart by studying the instructions for the Sherkhan alarm, on the basis of which the Magikar key fob is prescribed. Before starting programming, you need to deactivate the security functions, turn off the ignition and the hands-free option.

Next, Scher-Khan Magicar 5 is programmed taking into account the following rules:

1. Automatic launch can only be used in open space with the ability to visually assess the situation.
2. Do not start the engine if there are people behind you.
3. If the car is parked, it is important to first apply the parking brake.
4. When turning on the autostart function, make sure that the gearshift lever is in the neutral position.
5. Constantly monitor the coolant and oil levels.
6. Do not allow children to play with the keychain or perform any manipulations.

If you want to bind key fobs with auto start on cars with a manual transmission, you need to use one of the following options:

The first option involves programming the key fobs registered in the system after stopping the vehicle, fixing the parking brake and pressing the neutral position of the gearbox lever. If the engine remains running, open the door, go outside, and then slam it - the power unit should turn off.

If you need to get things out of the trunk, you should use the second method:

1. After selecting the neutral position of the lever, go outside without closing the door behind you.
2. Open the trunk and take out the necessary things from it.
3. Close the door, slam the lid.

There is a third option. It is based on this principle:

1. Select the neutral position of the gearbox and lock the handbrake.
2. Close the doors and press the 2nd button on the key fob, holding it for 2 seconds.
3. Turn off the ignition and leave the cabin.
4. Close the door and wait for the engine to stop.

By time

To flash the autorun firmware using a timer, you need to be guided by the factory diagram and programming table. First you need to press buttons 3 and 4 and use the diagram with the programming table, which tells you what to do and how to do it. There are two options:

1. Launch every day with an interval of one day.
2. Automatic restart after 2/4 or 8 hours.

By temperature and voltage

When programming key fobs (v) to configure autostart according to the temperature range and on-board voltage, you should follow these instructions:

1. Disable timer start.
2. Press button 4 at least 21 times.
3. Select the switching threshold.
4. Turn on the timer.

Peculiarities

The Sherkhan Magikar 5 connection diagram is presented in the manufacturer’s manual, which is supplied with the device. It's quite complicated. The alarm requires installation in the engine compartment of the car. To ensure that all systems work correctly, it is better to entrust this work to a specialist. Only in this case can you be sure that the software will work without failures. Special companies provide a guarantee for the installation of car alarm components.

Sherkhan Magikar 5 is compatible with gasoline or diesel engines. Its versatility allows installation on almost all modern machines. The limitation set by the manufacturer applies exclusively to the voltage in the electrical wiring. It should be 12 V. This ensures stable operation of all system components.

A computer installed in the car collects signals from sensors. They are mounted in the main systems of the car. After processing the received data, the on-board computer transmits the information to its owner’s key fob. The remote control has a liquid crystal display.

This allows the driver to understand the current state of his car’s systems. If necessary, it issues commands to the software from a distance. The signal range in open areas is about 1.5 km. The car should be parked in an open area. Houses, tree branches and other obstacles can delay the signal and reduce its range. The driver must see his car.

Video

The scher khan magicar 9 car alarm system installed on the car allows you to remotely start the engine using the main and optional key fobs. The security system also provides the ability to configure the autostart of the power unit based on time or depending on the temperature or voltage of the on-board network. These functions allow you not only to save time spent on warming up the engine, but also to heat the car interior to a comfortable temperature. In hot weather, the Sherkhan 9 autostart activates the air conditioning, making the car cooler before the driver and passengers board.

How to remotely start and stop a car

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

Remote engine starting using the main or optional key fob is performed by holding down key II for two seconds. At the same time, magicar 9 will activate the security mode, and all door locks will move to the closed position. In the case of the main key fob pager, the screen will display a successful engine start in the form of smoke from the exhaust pipe. The LCD display will also show a countdown until the magicar 9 needs to turn off the engine.

The warm-up time for remote start can be programmed to standard values ​​of 5, 15, 25, 45 minutes. To do this, you need to hold down the combination of buttons I and IV, and go to the menu and select the engine operating time. Which buttons to press to activate the required duration are indicated in the table below.

After the driver has figured out how to turn on the engine remotely, he can try to turn off the car using the key fob. To do this, you need to press the same key II for two seconds, similar to how to start the power unit.

Functions

Alarm Sherhan Majikar 9 has the following functionality:

• “Turbo” mode for cooling a turbocharged engine, preventing wear of parts (the duration of the function cycle can be adjusted by the user);
• “Comfort” option (used to activate security when closing the doors);
• alarm mode (light and sound alerts activated by user command scare away criminals);
• activation of protection when the engine is running;
• “Pit Stop” function (allows you to activate the protective mode when the key is missing from the ignition switch and the engine is running);
• Slave mode (allows you to control the alarm using a standard car key fob);
• hidden security (if an attempt is made to steal, messages are sent only to the control panel located by the owner; the siren does not work);
• remote engine start at a set time or temperature (the driver can start the engine by issuing a command from the key fob);
• step-by-step disabling of the security mode by entering an individual password;
• interior lighting control;
• control of engine starting using information from the tachometer, generator and battery;
• automatic blocking of door locks when the ignition is turned off.

Advantages and disadvantages

According to reviews from owners, the Sherkhan Magikar alarm has the following positive qualities:

• two-way communication (the option can only be used when the key fob is within range, the user sees messages about the status of the vehicle on the screen);
• reliable protection of the car from criminal acts (the alarm system is equipped with a coding system that prevents signal interception);
• an expanded set of functions (many necessary modes allow you to configure the car alarm in accordance with the user’s wishes);
• ease of installation and use (the instructions contain useful recommendations for installing and configuring the system).

The disadvantages include the following characteristics:

• interruptions in the operation of the Slave (when the turbo timer is turned on, the option becomes useless; it will not be possible to close the locks using the standard key fob);
• the need to comply with special conditions when activating certain functions;
• large dimensions of the key fob, causing inconvenience when wearing and using.