Features of the Sherkhan Logicar 1 alarm system and detailed installation and operating instructions

Author: Victor

The Sherkhan Logicar 1 car alarm system is the manufacturer’s flagship product, which has extensive functionality, including the option of feedback from the vehicle. Also, thanks to the unique signal coding, the security system is highly resistant to hacking.

[Hide]

Specifications

The Sherkhan Logicar 1 car alarm system has the ability to automatically start the engine either instantly, upon command from the communicator, or delayed, using a timer. The car owner is notified about the condition of the vehicle and the occurrence of alarming situations using the control key fob. For this purpose, vibration or sound signals are used.

Parameters that this system has:

• protection of pulse signals from interception is carried out using a special proprietary encoding Magic Code PRO 2;
• in alert mode, the operating radius of the key fob will be up to 1.5 km, and when transmitting commands, the range of the device will decrease to 500 meters;
• the ability to activate and disable the security mode without using a communicator, using a special password;
• using a code to disable security step by step;
• the presence of three types of alarm signals - audio, optical (using optics), as well as transmission of pulses via a radio channel;
• data is sent at an operating frequency of 433 MHz;
• to protect power lines, safety elements, resistor devices, transistors, and diodes are used;
• The microprocessor module is powered from the on-board network at 9-18 volts;
• the value of current consumption by the alarm in security mode will be from 20 to 35 mA;
• All functions of the system can be performed at air temperatures from -40 to +85 degrees;
• AAA batteries are used to power the main remote control, CR2016 batteries are used for the additional remote control;
• The service life of the batteries in the main communicator is about 4 months, in the additional one - up to three years.

MAGICAR model settings

This car alarm model is characterized by a high level of reliability and ease of control. To avoid errors while setting up the autostart system, do not forget to turn off the engine and turn on the security mode.

Here are some useful commands executed from the key fob:

Calculate the timing of cranking the starter so that the car has time to warm up before you arrive.

All Sherkhan alarm systems are highly reliable, so all malfunctions in the settings are most often caused by the inability of car owners to use the security system. Read the operating instructions carefully to avoid any difficulties.

Equipment

The Scher Khan system delivery kit includes the following elements:

1. Service user manual for system maintenance and setup. The documentation allows you to correctly install, connect and program the anti-theft system.
2. Wiring diagrams for connecting car alarms.
3. Main microprocessor device.
4. Communicator with liquid crystal display. Intended for adjusting technical parameters and alarm functionality. The presence of a screen provides the possibility of two-way communication with the complex.
5. Spare pager, no display. Its main feature and difference from the main key fob is the absence of feedback and a warning system.
6. Alarm installation kit, which includes power cables and connectors.
7. Shock and sensitivity sensor. Designed to detect any shocks and other impacts on the car body. In accordance with the signals sent from the sensor, information is supplied to the main communicator and control unit. If the impact is serious, the protection function is activated.
8. Valet service key, used to activate the emergency alarm mode. Equipped with a cable with a plug for connection.
9. Transceiver module with connected header.
10. Power unit blocking relay.
11. Limit switch for mounting on the hood.
12. Siren with connection block.
13. Sticker for fixing the antenna module on the glass.

For complete protection, before installing the Sherkhan Logicar 1 alarm system, you must additionally purchase limit switches for the doors and trunk.

The Arnage channel spoke in detail about the configuration of the Logicar 1 anti-theft complex.

Where is the jack button in the car?

Since the Valet button

on alarm systems Starline, Sheriff, Alligator, Pandora, Pantera, Scher-Khan and other popular models, it has miniature dimensions, it can be installed in the most secret place: under the fuse box cover, under the steering wheel, behind the glove compartment, behind the instrument panel, behind the radio, etc. d.

Interesting materials:

How to restore a previous session in Google Chrome? How to restore tabs in Chrome? How to recover deleted messages in Odnoklassniki? How to restore an icon to your desktop in Xiaomi? How to restore correspondence on Skype? How to recover messages in Viber? How to recover messages in Viber? How to recover deleted messages in Viber? How to restore a group in Viber? How to recover messages in Viber?

Main functions

Options that this alarm model has:

• the ability to synchronize the readings of communicators linked to the microprocessor module;
• option to control a second vehicle if it has a similar model of anti-theft system installed;
• presence of backlighting of the key fob screen;
• alarm option;
• online time display;
• locking buttons on the key fob;
• option to protect the car with the engine running;
• turning on the security mode without sound and alarm signals;
• the presence of five customizable channels for controlling additional electrical equipment;
• possibility of programming the type of power unit blocking relay;
• option to select the number of door lock control signals and their duration;
• closing and opening doors when activating and disabling the ignition system;
• the ability to monitor the intensity of engine operation in accordance with tachometer signals;
• option to automatically activate the protection mode;
• “Panic” function, which allows you to turn on alarms and lighting devices upon command from the remote control.

Functions related to automatic engine start:

• the ability to use this option on cars with manual or automatic transmission;
• setting up a remote start of an internal combustion engine (internal combustion engine) on vehicles equipped with a Start/Stop button to start the engine;
• the ability to use the function in cars equipped with diesel or gasoline power units;
• option to set the engine start time.

Description of car alarm Sherhan

This security system, as mentioned above, is designed for different types of power units (diesel and gasoline) and is ideal for both domestic and foreign-made cars of different classes, comfort and functions.

You should also draw the attention of those car enthusiasts who decide to purchase it to the possibility of installing additional functions and equipment that are not included in the basic package.

The Sherkhan alarm system has the following technical features:

• two-way communication, this is a digital security system that provides the ability for the car owner to communicate with his car via secure two-way communication channels, protected from code grabbers (devices that read codes);
• the presence of a built-in module, this innovation allows the magicar model (logicar 3) to connect to the digital car buses CAN and K-line, which are fully responsible for all the electronics and electrics of the car, this functionality helps the magicar 3 system, when it is installed, to connect to data digital buses without disrupting their operation, without additional equipment and unnecessary wiring;
• control using a standard Magicar 3 key fob, this system allows this security system to operate using the SLAVE function, that is, to completely monitor the car using a functional key fob and its LCD screen, arm it with the engine running, change the turbine cooling time, and also perform automatic setting of the car alarm at a specified time; there are special settings for this;
• functional key fob, its signal range reaches one and a half thousand meters, despite the presence of any obstacles, it is equipped with four buttons, which allows you to install various programs and functions, in addition, all possible system malfunctions are displayed on its functional liquid crystal display, as well as information about the state of the machine .

Key fob functions

The key fob of this magicar 3 security system has the following functions.

1. Multifunction display. Its peculiarity is that there are many icons (signal symbols) on its screen. From them you can find out what happens to the car when the owner is at a considerable distance from it, the charge level of the key fob battery (if it runs out, the key fob will constantly send signals), and the battery charge level. In addition, it has an alarm function, backlight, and shows the temperature inside the car.
2. Ability to drive a car. It must be said right away that this security system comes with two key fobs. Therefore, all information about the car and its systems is immediately sent to two key fobs, if they are turned on. The process of arming and disarming the alarm occurs with two buttons numbered 3 and 4. The user manual also indicates in detail how to use the key fob buttons (there are 4 of them) to program certain functions (autostart, turbine cooling, interior temperature control).
3. Double alarm. The car key fob emits a sound and vibration signal if strange things happen to the car in the absence of the owner (burglary, breaking glass, trying to start it). The key fob will also give a sound and vibration signal if the system detects any malfunction in the security system unit or key fob, or in the operation of the car itself. The sound and vibration signal will be duplicated by displaying the problem on the LCD screen with a certain icon lighting up.

Block functions

The magicar 3 model block has the following functions:

• the ability to control the power unit, some of the possibilities were mentioned above, additional ones allow you to set auto start at a certain time on automatic and manual transmissions, automatic shutdown, as well as warming up the engine, monitoring the intensity of the engine using the tachometer;
• control over the interior, functions for opening doors using a key, time to turn off and turn on the lights in the cabin, control over power windows, trunk and hood locks;
• security control, that is, you can set a function with signaling by light signals or without them (hidden security), PIN code for disarming if the key fob is broken or lost, two-step disabling of the security system (using a PIN code and working with a special button);
• diagnostic function, using special software, a car enthusiast can diagnose the operation of the security system and some vehicle functions via a computer and a USB cable.

The Sherkhan Logicar 3 car alarm has proven itself well in the security systems market, and is therefore in great demand among car enthusiasts.

Of course, every car owner is concerned about the safety of his car, its components and valuables in the cabin. This question will always be relevant. Most often, to protect their cars, owners equip them with car alarms, which not only can protect the car from theft, but also provide a number of service functions that provide comfort during operation.

Advantages and disadvantages

The advantages of this Sherkhan model:

1. Extensive functionality. The alarm system is equipped with many options that not only protect the car, but also simplify its use: synchronization of communicators, silent security mode, delayed engine start.
2. High reliability. In fact, it is almost impossible to hack the Sherkhan Logicar 1 signaling system by intercepting the code due to the author’s signal encoding system.
3. Affordable price. The cost of the alarm ranges from 3,800 to 5,000 rubles, depending on the region of sale.
4. Decent build quality. All elements and devices that are included in the system are supplied in a durable protective case.
5. No false positives. If the sensitivity of the shock sensor is correctly configured, the consumer will not be faced with the activation of the alarm mode for no reason.

Disadvantages that an alarm may have:

1. Incorrect operation of the system, “glitches” are possible. Consumers usually encounter this problem as a result of errors made during installation. In particular, we are talking about incorrect connection of wires.
2. According to reviews, another drawback is the low efficiency of the alarm at subzero temperatures. In cold weather, the system may execute commands late; sometimes LogiCar 1 does not respond to signals from the key fob.

The engine started, but it doesn’t show on the key fob

If the car was started not from an additional key fob, but from the main one, and incorrect information is displayed on it, then you should look for an error made when installing the alarm system.

Check that each connector on the main module is connected correctly. If there is no malfunction, contact a specialist.

PROMOTION: SALE OF NEW CAR 2022 PRODUCTION

The popularity of Scher-Khan alarms, especially the Magicar and Logicar families, is primarily due not to their any outstanding qualities, but to aggressive promotion in car dealerships at the time. In many cases there was practically no alternative as additional equipment. Accordingly, a solid statistics of problems with these alarms has accumulated, aggravated by the classic “in-line” installation method in dealer technical centers, where the “it will do” principle is practiced everywhere.

Therefore, it is not surprising that many people have encountered problems with autostart on Scher-Khan alarm systems. Meanwhile, these problems were often solved by reprogramming, so knowing the order of actions and their meaning will always be useful.

How to install an alarm?

The alarm can be installed in a garage. You must first prepare a set of tools for installation and also disconnect the battery.

To install an anti-theft system you need to have:

• multimeter for measuring voltage and determining breaks (short circuits) in electrical circuits;
• Screwdriver Set;
• set of socket wrenches;
• soldering iron;
• wire stripper;
• mounting blades for disassembling the interior;
• black electrical tape;
• foam;
• double sided tape;
• plastic clamps for fastening wiring.

Connection diagram

To connect the security complex, the following electrical circuit is used:

General card for connecting alarm elements (fragment 1)

General card for connecting alarm elements (fragment 2)

General card for connecting alarm elements (fragment 3)

General card for connecting alarm elements (fragment 4)

Step-by-step instruction

The installation procedure is as follows:

1. The microprocessor module is installed hidden in the vehicle interior. It can be located behind the instrument cluster, glove box or under the dashboard. It is advisable that in order to gain access to the device you have to disassemble the trim in the cabin, this will prevent the car from being stolen quickly. Double-sided tape or plastic ties are used to secure it.
2. The transceiver module is mounted in the upper corner of the windshield or rear window. It is important that the distance from the antenna to metal objects is at least 5 cm, this will avoid interference. Before installation, the glass surface must be cleaned. If the installation is carried out in winter, then its temperature can be at least 10 degrees Celsius. The wire from the antenna to the microprocessor module is laid under the decorative trim of the interior; during installation, care must be taken to ensure that the cable is not pinched.
3. The LED indicator is mounted in the corner of the front glass. First, its surface must be cleaned and degreased. You can embed the LED indicator into the dashboard, then you must first make a hole in it to install the light bulb.
4. The siren is located under the hood of the car, in a place that is maximally protected from external influences from under the bottom of the car. Do not install the siren near heating units and moving parts. It is recommended to place the device's horn down to prevent moisture from forming inside.
5. The hood limit switch is mounted on a metal surface that is as close to the body as possible. There should be no accumulation of moisture at the installation site. When the hood is locked, the sensor is protected by a rubber seal.
6. The shock sensor is fixed in the car using two bolts. During installation, it must be taken into account that the consumer must have access to the controller to change the sensitivity parameter. The sensor is equipped with two regulators. The first determines the sensitivity of the warning zone, and the second - the alarm zone. For fixation, it is better to choose the central part of the body so that the device detects physical impacts from all sides of the body.
7. If additional controllers are used, their installation is carried out taking into account the manufacturer’s recommendations. For example, the engine temperature sensor must be installed in the cooling system line.
8. After installing all the elements, they are connected to the control unit. The wires are laid under the decorative lining of the car interior.

User manual

Before using the key fob, you must install a working power source in the device. The battery is inserted into a special compartment hidden under the back cover of the communicator. Polarity must be taken into account when installing.

Designations of buttons and symbols on the key fob

All indicator designations and button numbers on the transmitter:

Designation of button numbers on the key fob

Pager programming

Without programming the communicator, setting up the Sherkhan Logicar 1 alarm functions will be impossible.

To bind a new remote control, perform the following steps:

1. The car alarm security mode is disabled. The ignition in the car must be turned off.
2. The button on the LED housing is pressed and held for two seconds. The car's headlights should then blink.
3. Within the next five seconds the button is pressed again. If a password has been set to control the alarm, the car's headlights should blink twice. If there is a PIN code, the blinking will be single.
4. If a password is used, it is entered. If you don't have a PIN code, you don't need to do anything.
5. After five seconds the LED will start to light continuously. This indicates that the car alarm is entering the communicator's binding menu. No more than three remote controls can be registered in the memory of the Sherkhan Logicar 1 microprocessor alarm module.
6. Over the next 5 seconds, the first key fob button is pressed. To program other devices, similar steps are performed.

How to program autorun?

To configure automatic engine start, you need to use the programming tables given in the instructions.

1. In accordance with the table, it is necessary to move function 2-13 to the third position. This will allow the car owner to change the assignment of programmable channels to control the starter device and ignition system.
2. Using the communicator, you need to set the time period from the moment the starter is turned on until the time the power unit starts. In accordance with the table data, the closest value for function 2-20 is set. If the setting is carried out on a vehicle with a diesel engine, then the time period for option 2-21 is indicated. If there is a Start/Stop button in the car, the values ​​of function 2-25 are adjusted. In cars with a turbocharged engine, option 2-24 is changed.
3. Then you need to adjust the parameters to ensure smooth operation of the function. This refers to the warm-up time of the power unit, as well as the operation of the headlights in automatic start mode. Additionally, you need to configure the number of cycles to start the motor in remote mode; it is recommended to select no more than four. If the engine will be started using a timer, you must select a time interval.
4. After the time is set, you need to “click” on button 4 ten times.
5. To complete the settings of all values ​​and functions, you must simultaneously press the second and fourth keys of the key fob. The timer option will be enabled. To disable the automatic start function, similar steps are performed.

Programming table

Programmable functions menu [buttons (II+IV)]:

Anton Kovalev spoke about the operation of the autostart option using the example of the Logicar 2 model; in the case of the Logicar 1 alarm system, the implementation principle will be similar.

Operating modes

The Logicar 1 system can operate in different modes:

1. To activate security, use the first button of the key fob, and to disable it, use the second key. After turning off the protection mode, all door locks will open, the starter mechanism and the power unit will be unlocked. If, when the security is deactivated, the alarm sounds six times with a siren, this indicates that the alarm was working. In the case of five signals, the system was turned on as a result of receiving an impulse from the sensitivity sensor.
2. Activation of the vehicle search function in a parking lot is performed with the first button. When setting this option, car security must be turned off. The vehicle's lights will blink five times, and the communicator will play a melodic signal.
3. To open the luggage compartment, the third key fob button is pressed for 2 seconds. When security is turned on, the mode will be turned off automatically, but the locks on the doors will not open. If necessary, the consumer can configure this option with unlocking door locks.
4. To check the status of the car alarm, the fourth key is used; it is pressed briefly. After the “click”, the communicator display should display data on the operation of the anti-theft system.
5. The “Panic” mode is activated by pressing and holding the 1st key fob button for two seconds. To disable the option, you need to “click” on the first or second key.
6. Activation and deactivation of alarm signals by command is carried out by pressing buttons 1 and 2 on the key fob.
7. Turning on and off the Valet service mode is done by simultaneously “clicking” on keys 1 and 3. This function is used if the car remains at a service station for repairs.
8. To turn the sensitivity controller on and off remotely, press buttons 1 and 4 simultaneously.
9. Activation and deactivation of the key lock mode on the key fob is performed by briefly pressing the third and fourth. When the function is turned on, the communicator will emit a short pulse and the display will show “Hold”.
10. Activation of the security mode with the engine running is done by pressing the first button on the remote control. The ignition must be turned on and all doors, as well as the hood and trunk, must be locked. The door locks will be locked, the alarm will activate the security mode. If the protection is turned off or the siren is activated, the anti-theft system will automatically stop the engine and block its operation.

Setting up the “Pit Stop” mode, in which you can turn on the security with the engine running and when there is no key in the ignition, is done as follows:

1. When the power unit is running, the transmission selector is set to the neutral speed position. In the case of automatic transmissions, the lever must be set to Parking mode.
2. The handbrake lever is lifted.
3. The second key of the communicator is pressed for two seconds. The transmitter will emit a melodic signal, the car's lights should blink once. The ignition support option will be activated, and the car’s headlights will blink once every five seconds.
4. The key is then turned to the Off position to turn off the ignition. The power unit will continue to function for a certain time, configured in advance by the consumer.

A detailed description of the options for the Sherkhan Logicar 1 key fob is provided by the Buyer Notes channel.

Why doesn't the car start with the Scher-Khan Universe pager?

Anti-theft systems Sherkhan Universal 1, 2, 3 are equipped with voice control and remote control via GSM communication. To enable autorun, do the following.

1. Press the # button for a few seconds. In this case, the engine should be running and the parking brake should be engaged.
2. Remove the key from the ignition.
3. Arm the alarm and press # for two seconds. The car should start with the key fob.

But there are times when the car does not start from autostart. The starter turns, but the engine is silent. This does not depend on the brand of the car; it can happen with both imported cars (Ford Focus, Hyundai Solaris) and domestic ones. Robot or mechanical box. This may happen for the following reasons:

• low battery charge;
• low engine temperature in winter;
• immobilizer malfunction preventing remote start;
• problems with the electrical equipment of the car;
• breakdown of the systems responsible for starting the engine.

If autostart fails, check whether the car starts with the key. If yes, then in this situation, reprogramming the autostart with a decrease in the startup frequency and an increase in temperature will help.

Possible faults

Problems typical for this car alarm model:

1. The key fob does not perform its functions and does not send commands. The cause of the problem may be low batteries, mechanical failure of the device, or a software malfunction. If the power supply fails, the battery must be replaced. If the problem is the negative impact of moisture on the device, but the key fob must be disassembled and dried so that there are no traces of water left on its board. If the remote control is damaged, its internal components are replaced by resoldering.
2. The wires through which the alarm is connected are damaged. With long-term use of the security system, wear of the conductors is possible, in particular if they are laid next to moving elements and components. To find a damaged cable, you need to use a multimeter. After replacing the wires, it is recommended to wrap them with electrical tape to provide them with additional protection from wear and tear.
3. One of the elements of the security complex has failed. We are talking about a transceiver module, a sensitivity controller, and a microprocessor unit. A detailed check of each device will be required; first of all, it is necessary to ensure the integrity of the contacts through which they are connected. If the control unit fails as a result of exposure to moisture, then its housing must be disassembled and dried by disconnecting its parts. Software malfunctions of the microprocessor can be resolved by flashing, which is best left to specialists.
4. False alarms have appeared, the alarm is activated for no reason. This problem is usually caused by the sensitivity of the kick controller being set incorrectly. To eliminate the malfunction, this operating parameter must be reduced by adjusting the sensor. It is not recommended to set the sensitivity value to minimum.

Protect your car even if the key fob is stolen!

This security system has powerful protection against electronic hacking attempts - it is equipped with a crypto-resistant radio signal coding algorithm MAGIC CODE™ PRO 2, and also in a number of operating modes time synchronization is used, which assumes an absolute coincidence of the time on the key fob and the unit when the car is disarmed.

Unlike most existing radio signal encoding systems, the unique MAGIC CODE™ PRO 2 keys are not transmitted live, which makes intercepting code messages absolutely pointless! The advanced error correction function allows you to accept and execute even commands corrupted by interference.

Video

The “Scherkhanalarm” channel spoke in detail about the security options of the Logicar 1 anti-theft system.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (75.00%)

No (25.00%)

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 4 votes, average: 4.75 out of 5)

Discuss the article: