Detailed review of the Sherkhan Logicar 4 car alarm: characteristics and differences, installation, configuration and operating instructions

Modern security systems are equipped with a separate input that allows you to read the high-voltage signal supplied to the tachometer. Based on the presence of a signal, the system determines whether the motor is running or stopped. This option is the most reliable if you compare it with control using a generator and so on. Next we will look at how to connect the Sherkhan signaling device to a tachometer sensor. We will talk about two different models: Logicar and Magicar of family 4. In theory, the Scher Khan Logicar 4 system will have to be additionally programmed, and for Magicar, and only for it, the settings are set by switches.

Connection diagram to the tachometer sensor

In the car you need to find a wire through which impulses flow while the engine is running, and when it stops there should be no signal. The pulse amplitude can reach 50-80 Volts, and there is nothing special about it. If the specified wire is found, make a T-connection to it.

The connection itself is the installation of an additional load. But its presence, as you will see, does not lead to breakdown of standard systems.

Next, if you are connecting a Scher Khan Magicar 4 alarm, find a yellow-black wire with a thin cross-section:

Next we look at how to configure the Scher Khan Magicar 4 system for tachometer control:

1. The DIP1 selector is moved to the ON position;
2. Connect the battery;
3. Start the engine with the key;
4. When the speed levels out, press the SW1 button for 1 second;
5. After releasing the button, a single beep sounds.

Let's say you hear a triple signal. This indicates that the system was unable to perceive the sensor signal.

If there are three signals, look at how the turn signals or dimensions behave:

• One flash – DIP1 in OFF position;
• Two flashes – there is no ignition (the green wire of the power terminal block is not connected);
• Three flashes are the worst: the tachometer signal was not received.

The sensitivity of the input receiving the high voltage signal cannot be adjusted. Also, on the Sherkhan alarm body there are no toggle switches that allow you to set the type of sensor (magnetic or Hall sensor). But even with a low-voltage electrical sensor, everything will work, which also applies to another system - Scher Khan Logicar 4.

Logicar, programming

Option "30" from table "2" should receive the value "2". In general, the Scher Khan Logicar 4 signaling is programmed from the key fob, and the key number corresponds to the value you need.

To start programming, the car is disarmed (key II). Then you need to do the following:

1. Turn off the ignition;
2. Press keys II and IV simultaneously, holding them for 2 seconds;
3. Short presses on the IV key select the option number;
4. The value is set with one click.

In the last step, obviously you will press the II key.

The firmware of the Scher Khan Logicar 4 system is designed like this: you can select both the option number and the table number. In the example, “table 2” is used, since buttons II-IV are pressed. Combination I-IV corresponds to “Table 1”. Exiting the service mode will happen automatically - just do not change anything for 4 seconds.

It turns out that the time period between the two closest actions should not exceed 4 seconds.

Training Logicar to idle

The essence of the actions repeats what was done to train the Scher Khan Magicar 4 signaling. But the button that needs to be pressed will not be installed on the main unit:

Sequence of training actions (security is not active):

1. Engine starting;
2. Pressing the VALET key for 2 seconds;
3. Before 5 seconds have elapsed, the key is pressed again and released after 4 seconds.

Successful learning is confirmed by a sound signal. If three signals follow, the system did not accept the sensor readings. Look for other connection points or refuse to use the option. Then the value “1” is set in the table. Good luck.

see also

Comments 14

Why don't you install heating? At -30C I turn on “Defa” for 8 hours (at night), start it in the morning, warm up the interior and go))

Yes, for some reason I don’t want to install heating, unless it’s Webasto and then how much money it costs)))

Webasta is a TOPIC, but it’s too expensive. And while warming up, you will spend more gasoline than with heating. But as they say, taste and color...

I do everything as it’s written there, but it’s still not set to 2 o’clock (first I press 2 and 4 at the same time, and then I press 2 and what appears is supposed to indicate 2 o’clock?

It happens? When enabling engine start by timer:

SIREN SIGNAL: One beep EMERGENCY ALARM: Flashes once LED INDICATOR: According to the status of the STSTS DISPLAY: Headlights flash five times, the lock image flashes five times, a mark appears on the display under the inscription “Timer” KEY FOB SIGNAL: One beep

The timer turns on but starts after 24 hours

PROGRAMMING FUNCTIONS USING THE KEY FOB

Programming STSTS functions using a key fob consists of four steps.

Entering programming mode and selecting the programming menu.

To enter Menu No. 1 “Central locking functions” press buttons I+II simultaneously for 2 seconds.

To enter Menu No. 2 “Security functions and operation of additional channels,” press the I+IV buttons simultaneously for 2 seconds.

The siren will sound one short signal and the hazard warning light will flash once, thereby confirming the successful completion of STEP 1.

Press the IV button to select the Menu function you want to change. For example, to select function 4, you must briefly press button IV of the key fob four times.

Wait a few seconds. The STSTS will confirm the number of the function selected for change with short siren signals and alarm flashes. The number of signals will correspond to the number of the selected function.

If, when choosing a function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you must repeat all the steps starting from STEP 1.

Press the I button to select the function's factory setting. To confirm this, the siren will emit one short signal and the hazard warning lights will flash once. Press button II to select an optional function value. To confirm this, the siren will emit two short beeps and the hazard warning lights will flash twice.

If you heard one long siren signal, this means that the STSTS exits the function programming mode. To continue programming, you must repeat all steps starting from STEP 1.

The timer turns on but starts after 24 hours

You need: 1.)Press the I+IV buttons simultaneously for 2 seconds. The siren will emit one short beep and the hazard warning light will flash once, confirming that STEP 1 has been completed successfully. 2.)Press the IV button to select the Menu function you want to change. To select function 2, you must briefly press button IV of the key fob twice. 3.)Wait a few seconds. The STSTS will confirm the number of the function selected for change with short siren signals and alarm flashes. The number of signals will correspond to the number of the selected function. 4.)Press the I button to select the factory default setting (24 hours). To confirm this, the siren will emit one short signal and the hazard warning lights will flash once. Press button II to select the optional function value (2 hours). To confirm this, the siren will emit two short beeps and the hazard warning lights will flash twice.

If you heard one long siren signal, this means that the STSTS exits the function programming mode. To continue programming, you must repeat all steps starting from STEP 1.

Characteristics of car alarm Sherkhan Logicar 4

The Sherhan Logicar 4 security system is designed to work on vehicles with an on-board voltage of 12 V and equipped with a standard CAN bus.

Characteristics of Sherhan Logicar 4:

• The duration of alarm pulses when security is activated is 30 seconds;
• protection of the processor and antenna unit is made according to the IP-40 standard;
• the siren is manufactured in IP-65 format;
• to send data between the unit and the communicator, a channel with an operating frequency of 433.92 MHz is used;
• control of the security complex is possible using a key fob, Valet service button;
• to protect signal power lines, fuses of a certain rating, transistors, resistors and diodes are used;
• The complex is powered using an on-board network designed for 9-18 volts;
• in protection mode, the current consumed by the alarm is 15-35 mA;
• The anti-theft system can operate in a temperature range from -40 to +85 degrees.

Main functions

Detailed overview of the main alarm options of Sherkhan Logicar 4:

1. Arming with or without sound and visual support. When the silent protection mode is turned on, the user will only be able to find out about an alarm being triggered by a message that will be sent to the communicator. The car's siren and lights will not work.
2. Monitoring the operation of the machine's power unit using tachometer readings.
3. Logicar has an automatic engine start function. The engine is started by command from the key fob or at the time specified by the car owner.
4. Self-diagnosis of all elements and equipment of the anti-theft system when activating and disabling the protection. Activation of the security mode is accompanied by testing of all devices connected to the control unit. If one of the faulty elements is detected, information is sent to the key fob.
5. Monitoring the condition inside the vehicle. It is possible to change the activation and deactivation times of lighting fixtures and adjust the operation of electric windows.
6. The presence of the “Slave” function, with which you can control the security complex using the remote control from the standard central lock.
7. Activate and disable protection automatically.
8. Availability of the “Panic” option. Upon command from the communicator, the user can turn on alarms.
9. Ability to configure priority opening of the driver's door.
10. Activation of the security function when the engine is running.
11. Using a personal password to disable the protection mode if the communicator is lost.
12. Possibility of programming additional channels for controlling electrical equipment.

Specifications

The Sher-han Logicar 4 car alarm has the following technical data:

• alarm duration - 30 seconds;
• type of power source of the head unit - vehicle on-board network with a voltage of 9-18 V;
• the frequency of the channel used to transmit data between the key fob and the head unit is 433.9 MHz;
• control method - using a communicator, digital vehicle tires and a service button;
• the amount of current consumed by the system when in security mode is 15-35 mA;
• operating temperature range - -40…+85°С;
• the range of the pager when transmitting signals is 800 m;
• The range of the key fob in message receiving mode is 1.5 km;
• range of the auxiliary communicator - 15 m.

Equipment

The Scher-Khan Logicar 4 alarm system is available complete with the following products:

• operating and installation instructions;
• installation cards, including electrical cable connection diagrams;
• head unit equipped with a microprocessor;
• main key fob with liquid crystal display and feedback function;
• auxiliary pager that does not have a screen or feedback;
• limit switch for hood with installation cable;
• protective relay for the power unit with connector;
• siren;
• a set of stickers for installing system components;
• antenna unit with transceiver;
• set of installation wires with connectors.

How to install a Sherkhan Logicar 4 alarm system?

Before installing the Sherkhan Logicar 4 complex, it is recommended to assemble all elements and connect them to the battery. This will ensure that the system is working properly and that there are no errors. After connecting the alarm to the car battery, you must first activate the operating mode and then turn it off. If it works, then you can proceed with installation on the car.

Activation of the limit switches of the Sherkhan Logicar 4 system is carried out only after stopping the car engine. The same goes for the kick controller.

Installation of Sherkhan Logicar 4:

1. The on-board network of the machine is de-energized. A wrench is used to disconnect the terminal block from the negative output.
2. The control unit is installed in a hidden place in the cabin, for example, behind the instrument cluster. The microprocessor module is installed with the connector down, which avoids moisture getting inside the device when drops of condensation flow down the wires. The block is wrapped in foam rubber to prevent the negative effects of vibrations while driving.
3. The siren is installed in the engine compartment of the car. The element must be installed secretly. The horn is directed downward to prevent moisture from accumulating inside the device. Do not place the siren near the cylinder block or intake manifold, or sources of moisture.
4. A Valet service key is installed in the car interior. It must be positioned so that the driver sitting behind the wheel has access to the element. You can cover the button with electrical tape so that it is invisible to prying eyes.
5. A transceiver module is installed on the windshield. The cable from it is laid under the decorative cladding.
6. A limit switch is mounted on the hood. If devices were purchased additionally for the doors and luggage compartment, then they are also installed. Wires from switches are laid under a plastic lining; there should be no rubbing components or parts nearby. Switches should not be installed in places exposed to moisture.
7. The shock and sensitivity controller is placed inside the car, preferably in the center of the body. It is possible to install the sensor on the partition separating the engine compartment from the passenger compartment. Do not use spacers between the controller and the work surface, as this may cause the device to operate without reason. The wires from the sensor are pulled under the interior trim towards the control module.
8. The power unit blocking relay is being installed. The element is installed next to the ignition switch. You will first have to remove its lining using a screwdriver.

The “We Repair Ourselves” channel showed the process of installing the Sherkhan Logicar 4 anti-theft system using the example of a Volkswagen Jetta.

Description of car alarm

This security system, as mentioned above, is designed for different types of power units (diesel and gasoline) and is ideal for both domestic and foreign-made cars of different classes.

It should be immediately noted that the basic set of its functions provides the ability to automatically start the engine, so the driver does not have to configure autostart as an additional function. The instructions for installation and use are simple and there are no difficulties in using it.

You should also draw the attention of those car enthusiasts who decide to purchase it to the possibility of installing additional functions and equipment that are not included in the basic package.

Alarm Sherkhan Logicar 4 has the following technical features:

• two-way communication, this is a digital security system that provides for communication between the car owner and his car via secure two-way communication channels, protected from code grabbers (devices that read codes), while the signal is not transmitted to the public (on the air);
• the presence of a built-in module, this innovation allows the Logicar 4 model to connect to the digital automotive buses CAN and K-line, which are fully responsible for all the electronics and electrics of the car, this functionality helps with its installation, connection to these digital buses does not interfere with their operation, when this is done without additional equipment and unnecessary wiring;
• control using a standard key fob, this system allows this security system to operate using the SLAVE function, that is, completely monitor the car with its help, arm it with the engine running, automatically arm the car with an alarm at a given time;
• functional key fob, its signal range reaches one and a half thousand meters, despite the presence of any obstacles, it has four buttons, which allows you to install various programs and functions, in addition, all possible system malfunctions are displayed on its functional liquid crystal display, as well as information about the state of the machine ;
• autostart of the power unit, this alarm system is classified as elite, due to the introduction of an innovative automatic engine start system, which provides not only warm-up and start modes at a certain time, but also the ability to control the operation of the starter and engine using tachometer readings.

It is interesting to know that the Starline alarm system, especially its model Starline A 91, also has similar functions, but unlike Logicar 4, its response time to turning off the starter is much longer.

Key fob functions

The key fob of this security system has the following options.

1. Multifunction display. Its peculiarity is that there are many icons (signal symbols) on its screen. From them you can find out what happens to the car when the owner is at a considerable distance from it, the charge level of the key fob battery (if it runs out, the key fob will constantly send signals), and the battery charge level. In addition, it has an alarm function, backlight, and shows the temperature inside the car.
2. Ability to drive a car. It must be said right away that this security system comes with two key fobs. Therefore, all information about the car and its systems is immediately sent to them if they are turned on. The process of arming and disarming the alarm occurs using two buttons numbered 3 and 4. Also, the user manual indicates in detail how to use the key fob buttons (there are 4 of them) to program certain functions (turbine cooling, interior temperature control, opening doors at a distance or key).
3. Double alarm. The car key fob emits a sound and vibration signal if strange things happen to the car in the absence of the owner (burglary, breaking glass, trying to start it). The key fob will also give a sound and vibration signal if the system detects any malfunction in the security system unit or key fob, or in the operation of the car itself. The sound and vibration signal will be duplicated by displaying the problem on the LCD screen with a certain icon lighting up.

It is important to remember that before using this security system, the car owner must carefully read the instructions and learn the designations of all icons in order to respond to the signals given in a timely manner.

Block functions

Model Logicar 4 instructions for use provide the following options:

• it is possible to control the power unit based on the operation of the tachometer, as well as automatically turn it on and off at a given time;
• control over the interior, functions for opening doors using a key, time to turn off and turn on the lights in the cabin, control over power windows, trunk and hood locks;
• security control, that is, you can enable the option with or without light signaling (hidden security), PIN code for disarming if the key fob is broken or lost, two-step disabling of the security system (using a PIN code and working with a special button);
• diagnostic function, using special software, a car enthusiast can diagnose the operation of the security system and some vehicle functions via a computer and a USB cable.

The main advantage of the unit is the ability to program it for various additional functions and download additional software.

The Sherkhan Logicar 4 car alarm has proven itself well in the security systems market, thanks to a large range of options and functions.

Key fob programming

Setting up your communicator can be done with or without a code.

No password

If there is no unique set of numbers, the binding is performed as follows:

1. The security function must be turned off and the ignition must be in operating mode. The Valet service mode entry button is pressed and held for two seconds. The vehicle's lights should blink.
2. In the next five seconds, the Jack button is pressed again. The car's headlights will flash twice.
3. After 5 seconds, the LED lamp will light continuously, this indicates that you have entered the communicator binding menu.
4. Within the next five seconds, you must press key 4 on the key fob. If binding is successful, the car's turning headlights should blink.
5. The rest of the communicators are configured in the same way.
6. To exit the programming menu, the ignition is turned off.

We start the car using the Scher-Khan Logicar key fob

Logicar anti-theft system models A, B, 1, 2, 3 i, 4 i, 5i, 6i, 5 iS, 6 iS are easy to operate. All actions are performed on the main key fob with a display; put the spare one aside. Configure autorun using the following algorithm.

1. By simultaneously pressing keys 2 and 4 on the remote control, activate the timer.
2. To enter programming mode, press and hold for a few seconds. buttons 1 and 4.
3. Activate the timed engine start by pressing key 4 ten times.
4. Set the time to turn on the car engine: once a day – key 1; after eight hours – 2; in four hours – 3; in two - 4.
5. Pressing 2 and 4 at the same time will turn on the timer.

Guide to using car alarms

Setting up all functions should be done only after binding the key fob, otherwise adjusting the parameters will be impossible. Before using the device, you must insert a working power source into it. To do this, open the back cover of the remote control, install the battery in the free compartment, taking into account the polarity.

Entering a personal password without a key fob

Guide to specifying the code if the communicator is missing or broken:

1. The vehicle doors are opened with the key, which activates the alarms.
2. The control element is installed in the lock. You need to turn on the ignition, but do not start the engine yet.
3. The Valet service button is pressed and held for two seconds. The light devices in the car will blink, the alarm should turn off.
4. Within the next five seconds, the key is pressed again. The LED will begin to flicker.
5. When the lamp blinks quickly for 4 seconds, you must enter the first digit of the code, the number of presses must correspond to it. If the symbol is indicated correctly, the car's headlights should blink.
6. The remaining digits of the password are entered in the same way. If the procedure is performed correctly, the siren will sound twice, and the car’s headlights will also blink. If the password is entered incorrectly, the device will sound an alarm.

Enabling/disabling the turbo timer

Activation and deactivation of this function is carried out with one combination of buttons: you need to press the third and fourth keys of the remote control. With the turbo timer activated, after the ignition is deactivated, the engine will idle for two minutes.

The function is configured like this:

1. On a car with a manual transmission, the gearshift lever is set to the neutral position; with an automatic transmission, it is set to the “Parking” mode.
2. Keys 3 and 4 are pressed.
3. The ignition is turned off. If configured correctly, the engine should remain running.
4. The driver leaves the barrier and locks all the doors. When the last lock is closed, the LED indicator will begin to blink.

Setting the time on the key fob

Changing parameters is done as follows:

1. The second and third keys of the communicator are pressed and held for two seconds until the “Pro9” indicator lights up on the key fob display.
2. The first button on the remote control clicks briefly. The alarm should go to the time settings menu. The display on the communicator will start flashing.
3. Press key 1 again and use it to adjust the clock values. The second button is used to change the minutes.
4. To leave the time setting mode, press keys 2 and 3. They must be held for two seconds.

User Sergey Gennadievich, using the example of the Sherkhan Logicar 6 alarm system (the actions are similar with model 4), showed the procedure for setting the clock.

Reset

1. The security mode, electrical equipment and ignition must be turned off.
2. The first and fourth buttons of the communicator are pressed and held for two seconds. The siren of the protective device will emit a single signal and the car's headlights will blink.
3. Press button 3 on the remote control three times. With each subsequent “click” the siren should go off, the same goes for the car’s lighting devices.
4. After a few seconds, the car's headlights will blink three times. This indicates that the settings have been reset to factory settings.

Enabling the protective function

Features of managing the security mode activation option:

1. The first key of the communicator is pressed.
2. The vehicle's headlights will turn on momentarily.
3. After activation of the protection, the security system LED begins to blink at a time interval of 1 second.
4. On the communicator display, the car optics should blink 5 times. An icon in the form of a closed lock is displayed on the screen.
5. The key fob plays a melodic signal, which indicates activation of the security mode.

Preparing the car for autostart

1. The car stops; there is no need to turn off the engine. The gearbox lever is moved to the neutral speed position or to the “Parking” mode if the car is equipped with an “automatic”.
2. The parking brake lever is raised. There is no need to keep your foot on the pedals.
3. The key in the lock must be turned to the “Off” position, then the control element is removed. If the doors are closed, the anti-theft system will intercept the ignition. Then the engine should continue to operate.
4. Over the next two minutes, you must leave the vehicle. After closing the door locks, the power unit should stop randomly. It will work for another two minutes if the “Turbo Timer” function has been previously configured.

User Anton Kovalev showed the operation of the automatic engine start option with the Sherkhan Logicar 4 alarm system.

User manual

For Logicar 4, the operating instructions describe all actions that may be required when programming and using the alarm.

Turbo timer

To enable or disable the Turbo Timer function, you must simultaneously press keys 3 and 4 on the control panel. To start the mode after a trip, you need to:

• set the gear lever to neutral position;
• turn off the ignition;
• leave the car and close the doors (the alarm produces several light signals).

Setting the time

To set the time you need to do the following:

• press buttons 2 and 3 on the key fob (the Pro9 indicator will appear on the display);
• hold down 1 key for a second (the current time indicator will flash on the screen);
• by pressing button 1 change the hour value, using button 2 to select the minutes);
• press buttons 2 and 3 simultaneously.

Reset

For Scher-Khan Logicar 4i, the instructions prescribe the following reset algorithm:

• simultaneous pressing of buttons 1 and 4;
• pressing key 3 three times (the siren will sound 3 beeps and the turn lights will flash).

The alarm settings will then change to the basic ones.

How to enable autorun

To enable automatic start by time, you need to hold down keys 1 and 2. Afterwards, it is recommended to press button 4 10 times in succession. Having switched to time mode, use keys 1 and 2 to select the parameter value. The timer will turn on after pressing buttons 2 and 4 simultaneously. Autostart by temperature is configured by pressing keys 1 and 4 on the key fob. To enter the menu, press button 4 15 times. The temperature value is selected using 2, 3 or 4 keys. Activate the function in Logic 4 by pressing buttons 2 and 4.

Why does the alarm not work and how to fix it?

Reasons why the system does not respond to the key fob or functions incorrectly, as well as recommendations for eliminating them.

You will need to disassemble the device and clean it of dust. If the malfunction is caused by exposure to liquid, then the board is removed from the communicator and dried in a dry and warm place.

It will fail if you dry it:

Connecting the key fob to the Sherkhan Logicar 4 alarm system

There are two ways to link the Scher Khan Logicar 4 remote control to the security system: without a PIN code and with its use. Let's look at the instructions without using a password.

1. Deactivate the vehicle security mode and turn on the ignition. Hold down the “Jack” key for two seconds. The hazard lights will flash once.
2. You have five seconds to take your next action. Quickly press "Jack". The lights will flash twice.
3. 5 seconds will pass and the LED will light up continuously. This is a signal to start entering remote control codes.
4. Complete the next step in five seconds. Quickly press the 1st key of the first communicator. Confirmation – the turn signals blink once. Enter the details of the remaining remote control communicators. If the action is carried out successfully, the emergency light will blink once. After entering the data for the third key fob, the light lights will blink twice and the control unit will exit the setup mode.

Procedure for entering a secret code.

1. Disarm the car and turn on the ignition. Hold “Jack” for two seconds. A single blink of the turn signals will confirm the correctness of your actions.
2. Within five seconds, click “Jack” once. One light signal will follow and the LED will flash quickly.
3. Complete the next step in 4 seconds. Click on the "Jack" key. The number of clicks is the first digit of the individual password. How will four seconds pass? the alarm will blink once. This is confirmation of the correct actions. The LED will flash quickly.
4. Using the same method, enter the remaining digits of the password (two or four).
5. After entering the last number of the secret code, the LED should be lit continuously. You can enter data for new control devices.
6. In five seconds. click the 1st key on the first remote control. After the alarm goes off once, press key 1 on the second and third key fobs. After encoding the third switch, the signal will exit the recording, confirming this with a double flash of optical instruments.

Instructions for Mobicar models

Remote engine start from the Mobicar A, B, 1, 2 alarm remote control is only possible in security mode. For a manual vehicle, carry out the following preparations.

1. With the engine running, the handbrake raised, and the brake pedal released, press key 3 on the key fob.
2. Remove the key from the ignition.
3. Get out of the car and arm it by clicking on button 1.

The following key combination will enable autorun.

1. Press button 3 for a while. An image of smoke will appear on the screen, indicating the engine is starting.
2. The autostart time will countdown. Briefly press 3 and you will stop the timer.
3. The mode is exited by long pressing key 3.

You can also set the autorun time manually by carefully reading the instructions.

Instructions for setting up a new Magicar 4 remote control

You can program an additional key fob without using a PIN code according to these instructions.

1. Turn the key three times within 4 seconds to activate the ignition. If the actions are carried out correctly, a single signal from the lighting devices will be given.
2. Within four seconds, press the 1st button of the first communicator. The hazard lights will flash once. If you do not continue programming, then after four seconds. The emergency light will sound twice and the service mode will be activated.
3. If you want to enter the data of the second remote control, then no later than four seconds, press the 1st button on it.
4. Use the same algorithm to register the third key fob.
5. After entering the last pager code, wait a little without pressing anything, the switch will automatically exit the adaptation mode.

System overview by model range

Scher-Khan Magicar Series

The Sherkhan Magikar alarm line is represented by several models.

Scher Khan 7 Magicar is a reliable, practical alarm system equipped with two-way communication and an auto-start engine function. The key fob, which has a range of 2 kilometers , combines the functions of control and information about unforeseen situations. The abundance of auxiliary functions, multi-level protection, thoughtful ergonomics and beautiful design allow us to call it a real breakthrough in the industry. Stream block ciphers, which encode access keys, prevent attackers from decrypting intercepted signals. Additional protection against substitution of control codes is provided by the time signaling function on the stopwatch of the ECU and the control key fob.

The Sherkhan 10 Magikar alarm system has received an updated encryption system. All information sent by the key fob into the air is encoded with a cryptographic algorithm Therefore, it will not be possible to hack the alarm system by intercepting the control signal. The alarm has an additional protective function. When it is turned on, the protection is removed only if the time on the stopwatch of the main unit and the key fob exactly match. The device has the ability to connect to CAN buses, which allows it to be used on modern cars without interfering with the “native” wiring.

Scher-Khan Magicar 11 alarm system has advanced software and hardware protection that can withstand high-tech equipment used by intruders.

Autostart by timer and temperature control allow you to comfortably use the machine in the most severe frosts.

Scher-Khan Logicar Series

Several models of Sherkhan Logicar . The control signal on them is encoded using a unique Magic Code Pro 3 . This allows the system to resist common hacking methods by intercepting commands.

The alarm key fobs have a contrast display , which is convenient to use in bright sunlight and at night. A two-way communication channel allows you to receive information about the status of security functions, engine temperature, battery charge, and the state of the engine start timer.

The module for matching the control unit with K-Line and CAN buses ensures compatibility of car alarms with the on-board electronics of modern cars.

Sherkhan Logicar models have a factory emergency disarm code. JackStop function , which is equipped with top models, is capable of resisting intruders even if the car is forcibly seized. Step-by-step ignition interlock is activated as soon as the car moves away from the owner.

The developers took care of the owners of cars with a turbocharged internal combustion engine - the alarm system includes a “Turbo timer” .

Alarms in this series have low power consumption, allowing the use of one AAA battery for 4 months.

Scher-Khan Mobicar Series

The alarm system embodies all the latest achievements in the industry, ensuring the protection of the car and making it difficult to break into:

• compact control unit;
• many control zones;
• built-in shock, movement and tilt sensors;
• signal encryption.

Radio exchange between the ECU and the alarm key fob is carried out at a frequency of 868 MHz. This ensures the channel's noise immunity over a long communication range.

Manufacturers have equipped Mobicar with a function to prevent accidents . If the accelerometer of the control unit detects a sharp deceleration of the car (more than 20 km/h per second), it turns on the car's hazard warning lights. This allows other road users to react to the situation and take measures to prevent an accident.

The autostart system is adapted for engines of any type and is mounted on a car with ignition keys and a start-stop button. The control unit is equipped with an adapter for connecting to K-Line and CAN buses of modern cars. Automatic engine start is triggered by a timer or when the engine cools to a preset temperature. In this case, the voltage of the on-board network is taken into account.

Scher-Khan Universe Series

Alarms "Sherkhan" Universe 1, 2 and 3 are capable of protecting a car from intruders, regardless of the distance to the owner. They are equipped with a GPS module that transmits the location of the car and records the car’s movements, saving the log on a remote server.

An additional level of protection in the form of an immobilizer on the Scher-Khan Universe 2 can prevent the car from being stolen even if the keys are stolen. If there is no signal from the key fob, the engine stalls 20 seconds after starting. This will prevent intruders from escaping, but will allow them to move to a distance that is safe for the owner.

Universe alarm systems have six control methods: alarm key fob, mobile application, personal account on the website, call to the service number and the Commander interior module.

Scher-Khan Canyon Series

An alarm that has not lost its relevance, which appeared on the market in 2009. Two-way communication with a key fob communicator, radio signal encryption and audiovisual confirmation of commands are also used on all modern models.

Scher-Khan Media One Series

Alarm system in 2010, in which operating at a frequency of 868 MHz installed for the first time among domestic systems . The color OLED display installed in the key fob made it possible to clearly demonstrate the execution of commands and the state of the security mode using animated images. The alarm key fob is equipped with a lithium battery, which can be charged from the mains or the vehicle's on-board power supply using adapters.

How to flash and reprogram a key fob

You replaced the old remote control device of the anti-theft system (damage) with a new one. Programming uses a PIN code. And you don't know how to set up the key fob correctly. There is nothing complicated about this, follow these steps.

1. Turn on the programming mode within 4 seconds by turning the ignition on three times. A single activation of the lighting equipment is a signal to begin entering the first secret code value.
2. The next step must be completed in four seconds. The password numbers are entered by turning on the ignition. The number of key turns is the first digit of Pin. Wait four seconds. A single flash of lighting equipment will follow. This is a signal to enter the second value of the unique code.
3. Using the same procedure, enter the remaining PIN numbers. Wait until the emergency lights go off once and start recording the key fob.
4. Within four seconds, press the I key of the first pager. An alarm flash will confirm the correct action.
5. Program the remaining remote devices in the same way.
6. Do nothing with the remote control for 4 seconds and it will automatically exit recording mode.

Sherkhan Magikar 2

This instruction is universal and is suitable for Scher Khan 3, 5, 8 remote controls.

1. Turn on the key fob programming mode by pressing for two seconds. electric buttons II and III. Login will be confirmed by the Pro9 picture.
2. To go to setting the time, press the I button once. The numbers should flash.
3. Key I changes the hours, and II changes the minutes.
4. Pressing 2 s of buttons II and III will exit programming.

It happens that the remote control stops working: it opens and closes the doors, but there are no symbols on the display. The key fob only shows the time. What to do in such a situation? Reboot the car alarm and re-register the remote control into the system memory.