How to set the time on the Starline A91 key fob: the alarm clock has gone wrong

In this article we will tell you how to set the time on the Starline A91 key fob. The instructions are simple, even a blonde can do it.

On the Starline A91 alarm system, the time setting is adjusted by button 3 of the key fob. Press and hold it until a series of beeps (1 long 3 short);
The time display will flash on the display. Using buttons 1 (+) and 2 (-) you need to set the exact time in hours;
Next, to save the result and proceed to setting the minutes, briefly press button 3 again. A scoreboard will appear on the monitor again, but this time to enter the exact time in minutes. To increase or decrease the value use the same 1 and 2 key fob buttons;

You don't need to press anything to save the result. Just wait for 10 seconds, the system will remember the set time and display it on the main display.
However, the time setting on the Starline a91 key fob is not limited to hours and minutes. If you click the 3rd key again, a menu will appear to enable/disable the alarm. Using keys 1 and 2 select the desired option.
If you need to change the moment the alarm goes off, briefly click on key 3 again. A display will appear. The required time is set in the same way, using keys 1 and 2. There is no need to save anything.
But that's not all. Another press of the program button 3 initiates the timer setting mode. Using familiar manipulations, set the desired value for hours and minutes, and also select the command: ON/OFF.

Let's summarize. The soft key (3) enters the time menu, as well as navigates through internal sections. Lowering or increasing indicators, as well as activating/deactivating the timer and alarm clock are performed using keys 1 and 2. Saving is automatic.

Reasons why the watch on the key fob fails

The time and date parameter is extremely important, so you need to periodically check its correctness. There are times when the clock gets lost and this can happen for a number of reasons. The most common one is a discharged power element. Each key fob is equipped with a battery, the charge indication of which is displayed on the main screen. Obviously, with minimal charge or its complete absence, this indicator may go astray. Mechanical damage is also a common cause of malfunction. Cracks in the key fob, its body or screen can lead to poor contact with the power supply itself. The result is loss of power and constant reset of settings.

If the key fob is completely intact, the nutrient element is in order and the contact is tight, but the time is still periodically lost, then the cause is a software failure. About setting the time on the Starline A93 key fob.

In addition, it is worth remembering that after replacing a tired battery with a new one, the main parameters of the security system are reset to factory settings. Accordingly, the time after replacing the element will be 00-00.

Setting the clock on the Starline key fob

A few words about the security system

These developments of security systems are among the most modern and reliable 12 Volt devices, have interactive authorization, encryption keys are individual for each product, and have a function such as remote start at a set time on the control panel timer or engine temperature. Performance is maintained even in conditions of strong radio interference in urban areas.

The use of interactive authorization eliminated the possibility of intelligent electronic hacking and provides high resistance to all code grabbers known today. This became possible after the use of conversational encoding algorithms, using individual encryption keys, as well as a new, previously unused frequency hopping method.

This encryption method is used for both control panels, both for the main key fob and for the additional one. The existing START/STOP button of this system fits well with machines that also have such a button. The device has good resistance to changes in outside air temperatures. High performance is maintained at temperatures from minus 45 degrees to plus 85 degrees.

Troubleshooting the alarm key fob

Some problems with incorrect display of the clock parameter can be resolved yourself. If the reason is a faulty or discharged battery, then you can replace the part yourself. To do this, you just need to open the back cover and install a new battery.

It is also advisable to check the contacts when replacing. If there is a suspicion of their oxidation or lack of conjugation with the nutrient element, then they need to be cleaned and bent.

Mechanical damage in the form of cracks in the display or breakage of the key fob body is “treated” by replacing the part. The new remote control can easily be “linked” to the old car. If the time is periodically “reset” or displayed incorrectly, then this is a software failure. Service center specialists and programmers will help you here. They will be able to conduct a thorough diagnosis, determine the cause of the malfunction and decide whether the remote control can be repaired or whether it will require a complete replacement.

Why it may not work and how to fix it

If it is impossible to enable autorun from the remote control, the reason should be sought in the following:

Incorrect setting of alarm unit operating modes. It is necessary to check and adjust the parameters.
Damage or failure of the control key fob or alarm. Check the operation of the system with an additional remote control.
To troubleshoot the remote control, replace the battery; if this does not help, the device must be disassembled. Often the cause of problems is the exposure of the communicator board to dust or moisture. After disassembling the case, the user needs to clean the circuit and also get rid of traces of moisture by drying the device in a warm and dry place. To remove dirt, you can use a cotton swab or a dry cloth treated with alcohol.
If the alarm operates from an additional key fob, then it is necessary to replace the battery in it.
Another reason could be a break or short in the control wiring. It is advisable to fix this problem in a specialized service. Damaged wires can be identified visually. First of all, it is recommended to check all contacts on the control unit, temperature sensor and ignition switch.
If only automatic start by alarm or timer does not work, then you need to check that the current time and the main options of the remote control are configured correctly. But this is only relevant if the remote engine start based on temperature is functioning.
The cause of the problem may be related to the standard immobilizer - there may be a conflict in the operation of the engine blocker and alarm system. To fix this problem, you will need to additionally install an immo bypass module. You can use crawlers from any manufacturer, but it is recommended to give preference to Starline blocks.
If this does not help, then you should contact the service for a more detailed analysis and purchase a new remote control or alarm.

Loading …

How to set the clock on the StarLine A91 key fob

One of the most popular Starline alarm models are the A series systems. Setting this parameter here is quite simple and is the same for all types. Below are instructions using the Starline A91 modification as an example:

The remote control is equipped with three functional buttons, each of which is responsible for a certain number of functions. To set the time on the Starline key fob, you will need to hold down the third button for a few seconds, until it emits a melodic signal. Afterwards, another sound should sound, and two melodies should also be played. Now the owner has entered the time settings mode, and the clock indicator blinks on the display.
Using the first and second buttons, the “Clock” parameter is changed. In the first case, it increases, in the second, it decreases. After setting the correct parameter, you must press the third button again. The “Minute” indicator now starts flashing. Its adjustment is carried out in the same way, by pressing keys 1 and 2.
The next click on the third button switches to the alarm setting mode. The procedure for programming it is exactly the same - the first button is responsible for increasing the parameter, the second - for decreasing it.
Pressing key 3 again allows you to activate or deactivate the alarm. In this case, the first button turns it on, and the second button deactivates it.
Another click of the third button allows you to go to the alarm timer setting menu. Parameters are reduced or increased in the same way.
It’s very easy to finish setting the clock on the Starline remote control - just don’t press anything for 5 seconds. The system will remember and save the changes made.

Description of the Starline 63 alarm system with auto start

Below is a detailed video review that will help you understand exactly how to fine-tune your watch.

Why doesn't the turbo timer work and how to fix it?

The main reasons why the turbo timer does not turn on, does not turn off the engine, or has stopped working normally and is activated every other time:

The function does not work as a result of incorrect connection of the system to the engine starting power line or poor contact. This problem may result in the option being activated randomly or not functioning properly. You must make sure that all contacts are connected correctly in accordance with the diagram presented in the instructions.
The option was configured incorrectly or all operating parameters were lost. To resolve the problem, you must repeat all setup steps again.
The timer does not work because the vehicle's parking brake lever is lowered.
Incorrect position of the gear lever. The selector must be set to neutral or to P mode for automatic transmissions.
The turbo timer function has been disabled.
Software failure in the operation of the alarm control unit. For this reason, the engine randomly stalls, and the anti-theft system “glitches” when working with other options.

What happens if you don’t configure the alarm remote control?

Of course, the alarm will continue to perform its basic functions if the time and date on the Starline key fob are not configured. The car will still remain under guard, the attacker will not be able to start the power unit, and the owner will receive an audio notification about hacking attempts.

However, many useful functions will not perform correctly. For example, automatic engine warming is carried out in conjunction with a clock. That is, if the owner needs to leave at 8 am, then the car can start at 7:50, reach operating temperature and warm up the interior by the specified time.

How to turn off the siren on Starline A91

But the system is “tied” to its internal clock, and if its parameter is displayed incorrectly, then the car will warm up at a different time. As a result, the driver will get into an unheated cabin and start driving on a cold engine. This is not good for the engine, because unheated oil does not provide sufficient lubricating properties.

After repeated procedures, the car may require major repairs. So, correctly setting the time on the Starline key fob not only makes life easier, but also takes care of the proper operation and safety of the car.

Cursor programming

Cursor programming, which appeared in the first generations of StarLine, is also used here. To call the cursor mode, you need to hold down button 2 or 3 until two beeps sound, after which the flashing cursor will appear on the first icon. You can move it using buttons 2 and 3, turning it on/off in a circle by pressing button 1.

Icon meaning:

“Clock” – auto-start mode from the key fob using an alarm clock.
“Hourglass” - periodic autostart according to a timer.
“Thermometer”—autostart again if the engine temperature drops below the set value.
“Wrench” — switching to service mode to transfer the car for repairs without a key fob.
“Turbo”—activated turbo timer (appropriate connections required).
“Auto” - automatic activation of the alarm after the ignition is turned off and all doors are closed. Please note that in this mode there is a risk of locking the car with the keys inside.
“Immo” is an automatic immobilizer; engine starting is blocked 30 seconds after the ignition is turned off, until button 2 is pressed.

Setting up autorun modes begins immediately after selecting the appropriate icon. To force autostart, you need to press and hold button 1, and after the sound signal, quickly press button 3. This combination works on both the main and additional key fobs. It also allows you to extend the autostart time when the engine is already running - the timer will start counting from the beginning. To stop the engine, you need to press 1 for a long time, and then 4 (or 2 on an additional key fob).

Download operating and installation instructions:

Operating instructions for Starline E90. Revision No. 5, September 2013

Installation instructions for Starline E90. Revision No. 5, September 2013