Some motorists think that the air filter is not a very important element of the car, and you shouldn’t think about replacing it in advance. But the quality of air purification also determines how comfortable the operation of the vehicle will be.
Air is a necessary component of the working mixture, since its amount in this mixture is more than 90 percent. Therefore, if the air purity is insufficient, then the operation of the motor will be difficult. For example, in desert conditions, one day of operation without a filter would be enough for the engine combustion chamber to become completely unusable.
Removing the air filter and air intake Lada Granta
Tools:
- Medium Phillips screwdriver
- Ratchet wrench
- 10 mm head
Parts and consumables:
- Air filter (if necessary)
- Rags
Note:
Remove the air filter to clean the cavity of the filter housing from dirt, replace it, and also to access parts and assemblies located in the front left part of the engine compartment.
1. While pressing the lock of the engine management system wiring harness block, disconnect the block from the mass air flow sensor connector.
2. Using a Phillips screwdriver, loosen the clamp securing the corrugated hose to the air filter cover pipe and remove the hose.
3. Using a Phillips screwdriver, remove the four screws securing the air filter cover.
4. Remove the cover.
5. Remove the replacement filter element from the housing.
Note:
If you only need to replace the replacement element, use a damp cloth to wipe off dust from the internal surfaces of the filter housing.
Install a new replacement element and then reassemble in reverse order
It is important to install the replacement element with the correct direction of the filter lamellas (as shown in the photo below)
If disassembly is to further remove the housing and duct, follow the steps described below.
6. Remove the canister purge valve from the filter housing holder without disconnecting the tube and wiring harness block from the valve.
7. The air filter housing is mounted in the engine compartment on three rubber supports. The two front supports are located on the upper cross member of the radiator frame, and the rear one is located on the battery platform bracket. Remove the front right support from the slot in the filter housing bracket.
8. Similarly, remove the front left and rear supports.
9. Remove the filter housing pipe from the rubber coupling of the air intake.
10. Remove the air filter housing.
Note:
Remove the air intake for replacement, as well as when dismantling the fan or radiator of the engine cooling system.
11. Using a 10 mm socket, unscrew the air intake nut.
12. Remove the air intake from the radiator bracket stud, disconnect the rubber coupling of the air intake from the air filter housing pipe and remove it from the engine compartment.
13. Remove the rubber coupling from the air intake pipe.
14. After carrying out the work, install all elements in the reverse order.
The article is missing:
- Photo of the instrument
- High-quality photos of repairs
Why do you need an engine air filter?
To form the combustible mixture necessary to operate an engine, a combination of fuel and air is needed. On average, a car absorbs about 15 liters of fuel from the atmosphere per 1 liter of fuel. It enters the system through the air intake, the air filter pipe, usually installed next to the radiator grille.
Its quality leaves much to be desired. Street dust and dirt rush along with the air to the engine through the manifold, threatening serious clogging, failure of the power unit and subsequent expensive repairs.
A reliable protection against these troubles is an air filter that cuts off the flow of such debris. The air filter corrugation installed after it passes a purified atmospheric flow suitable for work.
This device also eliminates the noise of air supply through the channels and regulates the temperature of the combustible mixture in gasoline internal combustion engines. The last factor is especially necessary in cold weather to heat the fuel. This achieves the optimal effect of fuel combustion and improves the environment: significantly fewer harmful substances are released through the exhaust system.
You can learn how to replace the cabin filter from the informative material of our specialist.
Original cabin filters
- 11180-8122010-00, 11180-8122010-01 and 11180-8122010-03 are old articles of cabin filters.
- 11180812201008 — Cabin filter (“Motor-Super” JSC, Togliatti)
- 11180812201082 — Cabin filter in LADA STANDART packaging (“BIG Filter” LLC, St. Petersburg, direct article number BIG FILTER GB9831).
- 11180812201083 — Cabin carbon filter in LADA STANDART packaging (“BIG Filter” LLC St. Petersburg, direct article number BIG FILTER GB9831C)
- 11180812201090 — Cabin filter (“TD OAT” JSC Tolyatti)
All of them are suitable for the Lada Kalina, Lada Granta family, as well as Lada Granta FL (after 09.2018)
Replacing the cabin filter of Lada Granta -
Replacing the cabin filter Mazda 3
It is designed so that the cabin filter on the Lada Granta is completely identical to the cleaning elements from the Niva (4x4), Lada Kalina. In fact, this is the same filter. The manufacturer did not come up with anything new when producing the Grant model. So when buying, feel free to choose one of the options, any will do.
It’s easier to replace the air purifier yourself, because the operation is not that complicated. Going to a service center requires time and money. Which is often missing.
Despite the perimeter protection of plastic, the air system element is very susceptible to moisture and splashes. There are frequent cases of premature wear and deformation due to moisture.
For the purpose of maximum protection and increased service life, motorists practice putting a stocking over the filter. It serves as an additional purifier along the air flow path.
How effective and acceptable this is is up to each individual to decide.
At the stage of warranty service, it is not recommended to install non-standard, atypical equipment, as this may lead to negative consequences in the operation of the mechanisms, and the warranty at the service center will be void.
How often should I replace?
The operating instructions for the technical equipment indicate an interval of 30,000 km. mileage In practice, few car enthusiasts adhere to the recommendations and try to update the cleaner 5 - 7 thousand earlier than the deadline. If the machine is operated in special climatic zones with increased dust and gas pollution, reduce the service life of the paper filter by a third.
When is it necessary to replace the interior cleaner:
- The service station mechanic indicated that the deadline had arrived;
- major car repairs;
- recovery after an accident, collision, impact;
- water ingress after long trips through puddles;
- scheduled technical inspection in the workshop;
- an unpleasant odor, rot, and defilement can be heard in the cabin;
- The strength of the air flow from the deflectors has decreased, there is no airflow.
Choosing a cabin filter for Granta
Parameters of the factory filter element: rectangular shape, 16.1 x 25.6 x 3.55 cm. The filler is made of special paper laid in several layers.
Along the outer perimeter there is a plastic casing, which simultaneously serves as a stiffening rib to avoid deformation of the product.
Some models have an aluminum insert in the center, but the price of such a product is somewhat higher than its stock counterparts.
Factory catalog numbers:
It is better to purchase factory-made consumables at official points of sale, dealers, and other representative offices.
Recently, the most popular method has become the ordering and subsequent installation of spare parts in certified workshops.
This can be explained by the following factors: low cost compared to alternative options, quality assurance, professional installation, post-warranty service.
Replacing the cabin filter of Lada Granta
Changing the cabin filter on a Lada Granta with your own hands is not that difficult, provided you follow the recommendations. No longer than 15 minutes in time.
Preparatory stage: a new cleaner strictly in accordance with the catalog articles indicated above, a set of automotive tools, a screwdriver, and rags.
Where is the cabin filter located: the location is not standard - under the frill on the right side. As car owners note, the design is inconvenient and access to the element is extremely difficult. To carry out maintenance yourself, you will need to remove two protective plastic covers.
Sequencing:
- We set the car to the manual parking brake and open the hood. There is no need to use an inspection pit or an electric lift, since the work is carried out exclusively inside the car;
- in the upper left part, closer to the wipers, unscrew the two mounting bolts (cross-shaped nozzle). We remove it and put it aside;
- in the cavity we find another plastic cover. On the left side it is fixed with one latch, on the right - with two. Unfasten and remove the cleaner with your own hands;
- Gently wipe the cavity of the plastic housing with a rag and install a new filter. Foam rubber on the bottom.
In conclusion, we assemble the structure of the Lada Granta air system, start the power unit, check the performance and tightness. If there is air leakage or deformation of the protective cover, the latter must be replaced.
(1
Reviews
№ | Positive |
1. | Vitaly, 32 years old, owner of Lada Granta: I bought the car six months ago, under warranty service, I buy only original consumables. By the way, the air filter is completely identical to the Datsun from Nissan, the catalog number of the Grant air filter is 272775PA0D. Cost 150 – 180 rubles, for Datsun 200 rubles. |
2. | Konstantin, 35 years old: before each scheduled maintenance I buy the consumables specified in the operating instructions. I think that native people are more effective than foreign ones. This is a subjective opinion, of course, but I’m happy with the quality. My advice to car enthusiasts. |
3. | Vladimir Ivanovich, 55 years old: after retirement, I have more free time, which I devote to Grant. I change oils, filters, and other consumables myself. I give preference to domestic producers. Optimal price-quality ratio, accessibility, developed network of official representative offices, dealers, and authorized service centers. |
4. | Kirill, 44 years old: at the previous maintenance, the technician pointed out the need to replace the air system filter; the old one was very dirty. Since I don’t understand brands, I entrusted the choice to a specialist. They installed domestic, “native” ones. My positive feedback and support from the manufacturer. |
5. | Vyacheslav, 28 years old: I bought Grant second-hand, the second owner, to clean it, I went to a service station and carried out a comprehensive diagnostic. There are no comments, the condition is good, all consumables need to be replaced. When purchasing, I made the choice in favor of the domestic one. |
Negative | |
1. | Savely, 39 years old: at the previous maintenance I bought “original” filters, I was dissatisfied with the quality, the accordion began to peel. I had to buy new ones, but foreign ones (Filtron AP 006). There are no complaints, it has been in use for several months. |
2. | Stanislav, 41 years old: I bought my own air purifier at the car market. Apparently, it was defective, served for several months, and then had to be thrown away. Since then I only buy MAHLE LX 220. Good quality at an affordable price. My advice to motorists. |
3. | Alexander, 47 years old: I have been working as a mechanic at a service station for five years, I know a lot about spare parts. I don’t trust domestic ones, only foreign analogues. I buy filters from Mann. Quality you can trust. |
Conclusion The process of removing the Grant air filter is not at all difficult, and can be done by the average driver. It is not necessary to have experience or skills; it is enough to follow the instructions in the instructions. You are guaranteed to replace the air filter yourself within 10 minutes. Depending on operating conditions, subsequent maintenance is required after 12 - 15 thousand km.
Replacement instructions
Manufacturers of Lada Priora and Grant recommend changing the filter after 30 thousand mileage. But in practice, it is advisable to change it every 10 thousand kilometers or when it gets dirty.
The signal for the replacement procedure is the following signs:
- engine power has dropped;
- fuel consumption has increased;
- exhaust gases contain large amounts of carbon dioxide.
The frequency of replacement is affected by operating conditions, driver's driving style and the quality of the filter element.
Lada Priora
To carry out the procedure, you need to prepare new consumables - an air filter for the Lada Priora and a Phillips screwdriver.
The procedure itself consists of a sequence of steps:
- First of all, you need to open the hood.
- Next, you need to unscrew the four fastening screws on the cover of the plastic housing of the Lada Priora air filter.
- Then we dismantle the cover and take out the old filter.
- The cavity inside the case must be cleaned of dust and dirt with a vacuum cleaner and a damp cloth.
- After cleaning the case, we install a new product. In this case, the corrugations should be parallel to the arrow drawn on the bottom of the box.
- Next, return the cover to its place and fasten it with screws. This completes the process of replacing the filter on the Lada Priora (the author of the video is Techno-056).
Lada Granta
To perform the replacement, you will need a new consumable from materials and a Phillips screwdriver from tools.
Replacing the Lada Granta air filter consists of the following steps:
First you need to open the hood and find the filter
It is located next to the expansion tank and battery. Next, unscrew the four bolts and remove the cover from the housing.
After removing the cover from the plastic box, remove the filter element. Before inserting a new consumable, you need to clean the plastic case from dirt using a vacuum cleaner and a damp cloth. When installing a new product, you need to pay attention to the arrow that is drawn on it. It is necessary to ensure that the arrow on the new consumable coincides with the direction of air flow
We install the cover in its original place and secure it with screws.
At this point, replacing the filter on the Lada Granta can be considered complete.
Necessary tool
To carry out preventive maintenance you will need: a Phillips-head screwdriver, rags, and a new cleaner. The rubber seal on the top cover of the housing must be replaced if it is damaged, deformed, or dried out.
Carry out work at home - prepare a household (car) vacuum cleaner to remove dust and leaf particles from the body cavity. During the filtration process, a large amount of debris from outside settles to the bottom of the plastic housing. Replacing one filter is not as effective as in combination with blowing with a vacuum cleaner or cleaning with a damp cloth.
When the fuel filter is dirty
The quality standards of gasoline at gas stations are constantly increasing, but it is not yet possible to get rid of the presence of mechanical particles and other contaminants in their composition. In addition, dirt, corrosive deposits and other fractions are also found inside the fuel tank. All this does not have the best effect on the operation of the power plant.
To prevent foreign particles from entering the cylinders and to rid the fuel-air mixture of excess condensate, coarse and fine fuel filters are used
Operating a car without these parts will lead to premature wear of the fuel pump, injectors responsible for stable injection of the mixture into the engine block with combustion chambers and the entire system as a whole, no matter whether it is 8-valve or 16-valve.
Fuel filter location
The Lada Granta has 8 and 16 valves, in luxury or in base - it doesn’t matter, the filters are in standard places. Fine cleaning element to the right of the gas tank at the bottom of the sill. This applies to all body types, sedan or liftback. It is secured with nylon or plastic clamps. To get to it, you need to use an overpass; if you wish, you can crawl under the bottom by lifting the desired side with a jack.
In order to secure such a procedure, you should duplicate the position of the car with an additional support, since the jack may fall off. The coarse filter, or simply a mesh, is located inside the gas tank on the gas pump. To access it, you need to fold down the rear seat. Under it there is a hatch through which you can get to the block with the fuel pump.
Replacement Regulations
The frequency of replacement of fuel filters on the Lada Granta is not of fundamental importance, regardless of the configuration, type of power plant and body design. According to the manufacturer, the mesh does not require replacement and is designed for the entire service life of the fuel pump. Considering the low quality of gasoline, this is not true. Such a statement can be justified if only high-quality and clean fuel is used. Of course, this does not mean that you need to change the filter often. But it is recommended to do this every time the fuel pump is removed for some reason.
They are considered consumables, i.e. such parts become dirty and wear out relatively quickly and must be replaced on time. The fuel filter under the gas tank (fine cleaning) according to the regulations on the Lada Grant 8 valves or 16 should be changed every 30,000 kilometers. In reality, everything looks a little different, since pollution directly depends on the purity and quality of gasoline at the gas station. Experienced car enthusiasts try to change the fuel filter twice as often, i.e. after 15,000 kilometers. Or once a year. And for some, even more often - during a seasonal oil change in the engine.
Signs of a faulty filter
The main problem of a clogged mesh is a decrease in fuel throughput. Accordingly, insufficient supply leads to a decrease in pressure in the fuel rail. The filter does not become dirty overnight, and therefore the pressure in the fuel system does not decrease immediately. At first, the effects of pollution are almost invisible. The lower the pressure in the system, the worse the fuel-air mixture. An insufficient amount of gasoline depletes the mixture with air, and accordingly, this negatively affects the stable operation of the power plant.
A clogged element can be identified by the following signs:
- unstable operation of the propulsion system;
- the engine stalls at idle;
- revolutions “float”;
- decrease in dynamic characteristics and power failures;
- When driving, sharp jerks are felt without pressing the accelerator pedal.
If any of the above symptoms occur, the first thing you need to do is determine the pressure in the fuel rail. If the level is below the values set by the manufacturer (less than 4 kgf/cm), the consumables should be checked and, if necessary, replaced. Since the fine filter is easier to change, you need to start with it.
Next, you can replace the filter in the gas tank. A dirty mesh in the tank negatively affects the proper operation of the fuel pump, since not enough fuel enters the fuel line. The gas pump increases speed, trying to capture more gasoline, as a result of which its already limited resource is sharply reduced. At the same time, do not forget that gasoline is also used to cool the working parts of the gasoline pump and lubricate them. Insufficient fuel leads to lack of lubrication and overheating.
Working principle of the air filter
During operation, the power unit requires a systematic supply of oxygen for the purpose of its subsequent mixing and ignition in the combustion chambers of the cylinders. To ensure the continuity of oxygen supply, pressure is created inside the system to facilitate the absorption of flow from the outside. The main air intake is the air intake.
During operation, along with oxygen, dirt, dust, sand, and other particles penetrate into the line and settle on the filter fibers. An excessive amount of “garbage” leads to its contamination and the formation of an artificial obstacle to the natural flow.
As a result, the power unit spends part of its efficiency to overcome resistance. In addition, fuel consumption increases, dynamics decreases, and operation is unstable at idle when starting the engine.
Reasons for replacing the air filter on the Lada Granta
As noted earlier, timely replacement of the air filter on a Lada Granta vehicle is very important. Next, the reasons will be stated according to which the car enthusiast will understand that it is necessary to perform the presented action.
There are a certain number of typical circumstances due to which the owner of a Lada Granta vehicle should replace the contaminated power unit air filter with a new element.
List of reasons:
- The most common reason is planned replacement. In this case, car manufacturers individually specify in the car’s operating manual the mileage of the vehicle or the time after which the car owner should begin replacing the old air filter with a new one. Auto industry experts recommend focusing on mileage, namely when the car reaches 15-30 thousand kilometers;
- The next reason is unscheduled pollution. Replacing the air purifier may be caused by the fact that the owner of a Lada Granta vehicle has been using the car for a long time in conditions where the air is heavily polluted - rural areas, off-road conditions. Sudden contamination of the air filter on a Lada Granta vehicle may be caused by the fact that the car owner used low-quality filter material in the presented device;
- The last reason to replace the air filter of a car's power unit is mechanical damage. The reason presented may be caused by an emergency in the car engine or in the air filter, improper installation of the filter material, as well as a large particle entering the air purifier, as a result of which the filter material was rendered inoperable. It is also necessary to note that air filters are damaged during other repair work, which means that in this situation the car owner is required to immediately replace the part.
Replacing the air purifiers of the power unit on a Lada Granta car is carried out based on the operating characteristics of the vehicle. Vehicle manufacturers do not always indicate mandatory timing for replacing the air filter. However, it is recommended to change air cleaners when changing the oil. This means that car enthusiasts need to change the air filter after the car's mileage has passed the 15 thousand kilometer mark. In addition, it should be noted that owners of vehicles with a diesel engine need to change the air filter more often. The design features of the designated motor unit require more attention to be paid to the designated part.
Before starting the process of replacing a dirty air filter with a new one, the owner of a Lada Granta vehicle should conduct a visual inspection of the part. Due to the fact that the indicated action is quite easy, every car enthusiast can carry it out. Even a beginner can distinguish the optimal condition of the air purifier of a Lada Granta car from a polluted one. There should be no oil stains on the surface of the air filter. Otherwise, replacing the air purifier is required.
Frequent inspection of the condition of the air filter of a Lada Granta vehicle is recommended for car owners who use the car on country roads: summer residents, rural residents, travel enthusiasts, fishermen. It is under these conditions that dust formation is most intense. These small particles rush into the inlet channel to the car's power unit through the air intake, which leads to engine failure or overheating. Based on the information provided, we conclude that in these conditions it is imperative to keep the air filter clean.
It should also be noted that there are signs by which the owner of a Lada Granta vehicle can understand that not everything is in order with the air purifier.
Symptoms that can help the owner of a Lada Granta car understand that the air filter is dirty:
- The car’s power unit is difficult to start and sometimes stalls while driving;
- Fuel consumption has increased significantly;
- Increased level of release of toxic substances;
- Loss of engine power in a Lada Granta vehicle;
- Data appears on the instrument panel indicating that the vehicle’s power unit is not operating properly.
In the above cases, you should immediately replace the VF of a Lada Granta car.
How to replace an element in the Grant model?
How to replace the air filter correctly and step by step?
- At the beginning of the “operation”, we open the hood of the Lada Grant and find a housing located directly next to the battery and coolant reservoir.
- Disconnect the connector from the MAF socket.
- Using a screwdriver, unscrew the screws securing the housing cover of the LADA Granta element. Before the procedure, it is recommended to clean the “box” of dust and dirt. A vacuum cleaner or compressor for blowing a stream of compressed air is perfect. Here we cover the MAF socket with a suitable rag.
- We take out the used element.
- We correctly install the new element on the Lada Granta. To do this, look at the arrow marked on the surface of its frame. Its pointer should coincide with the direction of the air flow. This is a very important point, since an incorrectly installed element will not ensure the effective functioning of the air supply system.
- We reassemble all the dismantled elements in reverse order and connect the removed connectors.
This completes this simple procedure, the air filter is installed on the Lada Granta car. Please note that reusing an old filter is unacceptable. It must be disposed of without alternative. And when the air filter is replaced, an exclusively new one is always installed.
Each part of the vehicle has its own special purpose. If individual elements of the car malfunction, this defect affects the performance of the car as a whole. The air filter is no exception. This article will provide information about the role of the air filter, its purpose, as well as the importance of timely replacement of the air cleaner on a Lada Granta car.
Each Lada car model has its own air filter model. The main differences between air purifiers are their shape and size. Any of the air filter models is based on a filter element, the functions of which are as follows: protecting the vehicle’s power unit from dust, moisture and dirt.
The engine of a vehicle, and in this case the Lada Granta brand, cannot run solely on fuel. Air is also required for its optimal functioning. Big cities often don't have the cleanest air. In addition to oxygen, the urban atmosphere also contains a large amount of impurities such as dust. This creates a high probability that undesirable substances will enter the vehicle’s power unit, which will affect the performance of the vehicle. And to prevent such a situation from happening, an air-filtering auto part was created.
This article will provide information on how a car owner can independently replace the air filter on a Lada Granta car, when it is necessary to do this, and about the negative consequences of untimely replacement of the air filter.
Design features of the “air filtration system” of 8 and 16 valve engines
The air supply elements in the 8 and 16 valve engines of the Lada Granta do not have any special design differences. Therefore, we will look at the process of replacing the air filter using the example of an 8-valve engine 21116.
Of all the tools we need, we will need moderately straight hands and a crosswise screwdriver. Difficulty: minimal. But the result can exceed all expectations. A clogged filter may result in loss of power and increased fuel consumption (factory fuel consumption data).
Replacement process with photo
- Open the hood. The air filter housing is circled in red.
- Remove the terminal from the MAF connector. You don’t have to remove it, but it’s more difficult. Disconnect
- We take a screwdriver in our hands and unscrew the 4 bolts securing the air filter housing. These bolts must be unscrewed
- We remove the old filter.Old filter
- We clean the filter housing from the inside; most likely, there will be a lot of dust inside it, and there may also be dry leaves. You can use a damp cloth, just make sure that the lint does not remain in the filter housing after use.
- We install the new air filter in the same way as the old one.
- We assemble the body and screw back the 4 bolts. Screw everything back
Air filter life
The service life of the air filter is marked on its housing.
The service life of the air filter is 30,000 km.
This is the number indicated on the case. But it should be remembered that if the car is operated in poor external conditions, then this figure can be reduced. In this case, it is necessary to regularly check the cleanliness of the filter.
If you mainly drive on dirt roads, then replacement may be required after six or even five thousand kilometers. In desert areas the situation will be even more complicated.
Part numbers
There should be no problems purchasing an air filter. They are available in any self-respecting auto store. But just in case, we will write a couple of proven articles.
GB-9597 E4 - Big Filter - (146 rubles in total in the autodoc) One of the cheapest filters
Working principle of the air filter
Left - old, right - new air filter
Air intake usually occurs from outside the vehicle.
And, given that the conditions outside can be very different, sand, dust, pieces of asphalt and even pollen can get inside with the air.
All these inclusions do not allow the engine to operate properly. So, on the way from the air intake to the engine there is an air filter in which these particles are retained.
Most often, so-called dry air filters are used, which have the structure of a regular paper cartridge. As the practice of the automotive industry has shown, it is this filter format that has the best ratio of cost and degree of purification.
Air filter devices
The design of such a filter requires the presence of a plastic casing in which the cartridge is located. It, in turn, includes a frame with a special sheet of paper folded like an accordion. The paper should have a pronounced porous structure. And additional processing of the paper allows us to talk about reliable protection against moisture, which can damage ordinary paper products. And the peculiarities of the interweaving of cellulose fibers are such that air can pass between them, but anything larger than microscopic sizes will be retained.
Injection car models, as a rule, use rectangular-shaped filters, while carburetor options use oval and round shapes. The box can last quite a long time, but the filter element itself needs to be changed regularly.
Which air filter to choose?
The dry paper filter option we already mentioned is standard for most machines. But, sometimes, alternative options may be used. We are talking about liquid-type models that use mineral oil to purify the air. Moreover, in order to save money, you can choose already used material for the role of oil.
The key advantage of such filters is that you can change the oil as soon as the old one becomes too dirty. But the disadvantage of such filters is that they have a large mass, so they should not be used on modern cars.
Zero resistance filter under the hood of Lada Granta
Separately on the list are “zero resistance” filters, which have a special structure, but are built on the same type of paper. They are used on cars with a sporty "bias". This can significantly increase the engine power.
➤ Replacing the Lada Granta air filter - detailed description
The importance of the Grant liftback air filter is somewhat exaggerated - this is an opinion expressed by inexperienced motorists. And this is the main mistake of “young” drivers
The functionality of the air system cannot be underestimated.
The dynamics of vehicle acceleration, fuel consumption, and stability at idle speed depend on the percentage ratio of air and fuel. Timely replacement of the cleaning element, purchase of original components, professional installation is the key to a long service life of the technical product.
Working principle of the air filter
During operation, the power unit requires a systematic supply of oxygen for the purpose of its subsequent mixing and ignition in the combustion chambers of the cylinders. To ensure the continuity of oxygen supply, pressure is created inside the system to facilitate the absorption of flow from the outside. The main air intake is the air intake.
During operation, along with oxygen, dirt, dust, sand, and other particles penetrate into the line and settle on the filter fibers. An excessive amount of “garbage” leads to its contamination and the formation of an artificial obstacle to the natural flow.
As a result, the power unit spends part of its efficiency to overcome resistance. In addition, fuel consumption increases, dynamics decreases, and operation is unstable at idle when starting the engine.
When to change the air filter on Grant
The manufacturer in the manual indicates a replacement interval of 30,000 km. In relation to domestic transport, including the Lada Granta, the indicated resource is slightly increased. Experienced car service workers recommend replacing the Grant air filter at around 12,000 km.
If the machine is often (systematically) used in conditions of increased gas pollution, reduce the replacement interval by a third. Regardless of the quality of the material or the originality of the workmanship, dust particles still penetrate inside, interfering with normal functioning. Part numbers and overview of manufacturer prices
Brand / article / OEM | Price, rub.) |
GB-9597 E4 Big Filter | from 150 |
MANN-FILTER C 22 117 | —/— |
LYNXauto LA-1505 | —/— |
CHAMPION CAF100505P | From 200 |
PURFLUX A515 | —/— |
KNECHT LX 220 | —/— |
FILTRON AP006 | From 250 |
CLEAN FILTERS MA 435 | —/— |
Factors for the need for replacement
When learning how often to change your engine air filter, you need to consider the factors that influence this. In some cases, cleaning elements become clogged faster than indicated by the manufacturer in the operating instructions. This may be due to the harsh operating conditions of the engine.
During the summer season, dust from the road rises more strongly. If the car is driven in snow, the air filter becomes clogged much more slowly. Also, in addition to dirt from the external environment, engine oil can get into the cleaner. This also leads to the need to replace this motor element.
If the engine is new and operated in relatively clean conditions, it will need to be replaced much less frequently. For cars with high mileage that drive on dusty roads, this process will have to be done more often.
Other FILTRON selections for this brand
Automobile | Selection |
Selection of FILTRON filters for LADA (BA3) 110 (VAZ-2110)(1.3 Wankel) | View selection |
Selection of FILTRON filters for LADA (BA3) 110 (VAZ-2110)(1.5) | View selection |
Selection of FILTRON filters for LADA (BA3) 110 (VAZ-2110)(1.5i) | View selection |
Selection of FILTRON filters for LADA (BA3) 110 (VAZ-2110)(1.5i 16V) | View selection |
Selection of FILTRON filters for LADA (BA3) 110 (VAZ-2110)(1.6) | View selection |
Selection of FILTRON filters for LADA (BA3) 110 (VAZ-2110)(1.6) | View selection |
Selection of FILTRON filters for LADA (BA3) 110 (VAZ-2110)(2.0i 16V) | View selection |
Selection of FILTRON filters for LADA (BA3) 111 (VAZ-2111)(1.5i) | View selection |
Selection of FILTRON filters for LADA (BA3) 111 (VAZ-2111)(1.5i) | View selection |
Selection of FILTRON filters for LADA (BA3) 111 (VAZ-2111)(1.5i) | View selection |
Where is the cabin filter located on the Lada Granta?
Until 2012, in accordance with the design solutions of the AvtoVAZ company, the cabin filter was provided under the hood of the car. Since the release of the Largus model, the purifier has been moved to the interior. In Lada Granta, the filter element is placed according to the first method.
To understand where the air filter is located, you need to consider the engine compartment. Between the engine compartment and the windshield, closer to the passenger seat, under a plastic cover, there is an air purification system. If you remove the casing, you can see the filter - it looks like an accordion made of paper.
Types of filter elements
It should be noted that there are two most common types of products: - coal type; - paper type.
The carbon element has excellent filtering characteristics. The product perfectly freshens the air, copes with dust and unpleasant odors (dampness, exhaust gases and emissions). The optimal place for use is large, polluted cities. The disadvantages include the rather high price and short service life.
A paper filter element is much cheaper than a carbon one, and is slightly more durable under conditions of proper use. In principle, it also carries out all the necessary protective functions, but does not do it so zealously and thoroughly. The disadvantages include excessive fragility and wear when the product gets wet.