Replacing the timing belt on a VAZ 1111 Oka: diagrams and instructions

Timing for replacing timing belt

According to the regulations, car owners are recommended to check the condition of the timing belt, as well as its tension, every 30 thousand km.
It is recommended to replace the belt, despite its condition, after a mileage of 60-70 thousand km. If you do not change the belt in time, it may break, and this, as mentioned earlier, threatens very serious damage to the engine, and therefore expensive repairs. It is strictly prohibited to operate an OKA vehicle if even the slightest traces of oil are found on the surface of the timing belt. The leak must be identified and repaired immediately, and the belt must be replaced. If the timing mechanism is serviced on time and efficiently, then the car owner should not have any problems. If you follow all the tips given in this article, replacing the belt will seem like the simplest action possible.

In 1989, car enthusiasts saw the first copies of the VAZ 1111, which became the basis for the family. Three factories mastered the production of small cars: VAZ in Togliatti, KamAZ in Naberezhnye Chelny, Serpukhov, whose car plant specialized in the production of motorized wheelchairs for the disabled. This distribution of forces and resources made it possible to quickly begin production of this model without the construction of new production facilities.

Buyers were offered two versions of the car, which differed only in the power unit. The car has front-wheel drive, and replacing the Oka timing belt is carried out by analogy with VAZ 2108 and VAZ 21083 engines.

Checking and adjusting the ignition timing of VAZ "OKA" 1111 1988-2008

Ignition timing is a very important parameter on which the normal operation of the engine depends. If this timing (ignition timing) is set incorrectly, the engine will start poorly, operate unstably at idle, not develop full power, overheat and consume gasoline unnecessarily. In addition, if the ignition timing is too large (“early” ignition), detonation may occur - a very dangerous phenomenon, often leading to emergency engine damage.

In a contactless ignition system, ignition timing (ignition timing) can only be set using a strobe light

A strobe light is available to almost every motorist, as it can be purchased at almost every auto parts store at an affordable price.

The ignition timing is checked and set at engine idle (at a crankshaft speed of 820–900 rpm). The angle should be within 1°± 1° BTDC.

Check the ignition timing using the mark on the flywheel and the scale of the crankshaft rear oil seal holder (the rubber plug has been removed). When the marks on the flywheel are combined with the middle division (notch) on the scale, the piston of the first cylinder is installed at TDC. One division on the scale corresponds to 2° of crankshaft rotation.

The ignition timing can also be checked and set using the marks on the generator drive pulley and the front camshaft drive belt cover. The long mark corresponds to the installation of the first cylinder at TDC, the short mark to the ignition advance by 5° of crankshaft rotation. These marks are used to set the ignition timing on the stand.

• 
  Replacing timing belt Lada 2114 (Lada (VAZ) 2114) in Moscow - compare prices

1. For ease of operation, remove the air filter (see “Removing and installing the air filter”).

2. Disconnect the hose from the vacuum regulator.

3. To check the ignition timing, connect the “+” clamp of the strobe to the “+” terminal of the battery, and the “ground” clamp of the strobe to the “–” terminal of the battery.

4. Remove the tip of the high-voltage wire from the spark plug of the first cylinder and connect it to the strobe sensor in accordance with the instructions included with the strobe.

5. Remove the rubber plug from the clutch housing hatch.

6. Start the engine and direct the flashing strobe light into the clutch housing hatch.

The stroboscopic effect is based on the inertia of human vision. With frequent alternation of bright flashes, the eyes see objects only at the moment of the flash. If the frequency of repetition of flashes coincides with the frequency of rotation of an object, this object appears motionless. When adjusting the ignition timing, the flywheel with a mark on it appears motionless.

Illuminated by strobe flashes, rotating engine parts (crankshaft and generator pulleys, cooling system radiator fan), as well as the generator drive belt, appear stationary or slowly moving. Be careful not to get injured.

7. When the ignition timing is correctly set, mark 1 on the flywheel should be between the middle division 2 and the previous division 3 of the scale. Otherwise, it is necessary to adjust the ignition timing.

• 
  When to change the timing belt according to regulations and expert advice?

  Read also:  Buy in an online store, best prices, inexpensive delivery

8. To set the ignition timing, loosen the three nuts securing the spark timing sensor.

9. To increase the ignition timing, turn the sensor housing clockwise (the “+” mark on the flange of the sensor housing is towards the protrusion on the auxiliary drive housing. In this case, one division on the flange corresponds to 8° of crankshaft rotation). To reduce the ignition timing angle, turn the sensor housing counterclockwise (the “–” mark on the flange of the sensor housing is towards the protrusion on the auxiliary drive housing).

10. Tighten the sensor mounting nuts, check and, if necessary, repeat the ignition timing setting.

11. Connect the hose to the vacuum regulator.

Source

How to replace the belt on the Oka?

Difficulties should not arise when replacing the timing belt on the Oka if the procedure was always carried out in a timely and correct manner. All repair work must be carried out on a flat surface. First, place wheel chocks under the rear wheels to prevent the car from rolling.

Next you need to perform the following manipulations:

1. Remove the spare tire and washer water tank from the engine compartment. You will also need to remove the air filter housing and the ignition coil.
2. Loosen the tension on the alternator belt and remove it.
3. Remove the plastic casing that covers the drive.
4. Rotate the crankshaft clockwise to align all marks.
5. Install the socket 19 through the hole on the right mudguard onto the crankshaft pulley bolt. To unscrew it, you need to secure the engine from turning. To do this, put an assistant in the car, he must press the brake pedal with 4th and 5th speed engaged.

Ignition Features

Before we talk about how to set and adjust the ignition on the Oka with your own hands in accordance with the diagram, let's understand the features of the SZ.

The ignition system on any car includes several different components, the main ones:

1. Spark timing controller. This device is equipped with vacuum and centrifugal regulators. The device is designed to ensure the timing of spark formation, taking into account its standard installation, the number of engine revolutions, and the load on the motor. The signal reading procedure is based on the Hall effect.
2. The switching device is designed to open the supply circuit of the primary winding of the short circuit, thus converting control signals into current pulses. When the ignition is activated, the connector of the switching device must not be disconnected under any circumstances, since this will lead to damage not only to this unit, but also to other elements of the SZ.
3. Coil. In the ignition systems of Oka cars, in accordance with the diagram, a two-terminal short circuit with an open or closed magnetic circuit is used.
4. Candles. This element is designed to transmit a high-voltage pulse, which contributes to the ignition of the combustible mixture in the cylinders of the internal combustion engine. The service life of spark plugs is about 10 thousand km, but this figure can be changed upward in accordance with the specifics of the spark plugs themselves. Or to a lesser extent, if for some reason the service life of the spark plugs is reduced.
5. High-voltage cables designed to connect spark plugs to a distributor. In Oka, high-voltage circuits with distributed resistance are used. Do not touch them while the engine is running, as this may cause serious injury. It is also prohibited to start the power unit if the high-voltage circuit is broken (the wires may be broken or crushed, or the insulation on them may be damaged). If the insulation is broken, then other elements of the system may fail in accordance with the diagram.
6. Egnition lock. According to the diagram, the lock is designed to start the engine by supplying voltage to an additional relay when the key is turned (video author - Nail Poroshin).

Typical system malfunctions

Among the malfunctions of the SZ, the following should be highlighted:

1. Coil failure. This problem doesn't happen often, but it can happen nonetheless.
2. Distributor failure. You can read more about distributor malfunctions, as well as troubleshooting, here.
3. Spark plugs are worn out or have carbon deposits on them. This problem is relevant for many of our compatriots. Read about the reasons why soot appears and what ways to eliminate this problem exist in this article.
4. Malfunction of high-voltage wires. The wires may be broken (broken) or their insulation may be damaged. Operating a car with such a problem is not allowed.
5. Broken ignition switch. Wear on the inside of the lock will result in the driver being unable to start the engine with the existing key. Replacing the lock cylinder will solve the problem (the author of the video is Mikhail Burashnikov).

What will you need?

The only problem with timing belt adjustment is the shims. The fact is that a professional set of them is quite expensive, since it includes washers with a thickness of 3.0 to 4.5 mm (in increments of only 0.05 mm).

• 
  Which timing belt is better to choose for a VAZ-2112 16 valves

But many auto stores sell these washers separately, so the price of one washer is low. Only in the process of carrying out the work will you have to make all the necessary calculations, go to the auto store, purchase the required sized elements and download the assembly.

In addition, you will also need special devices - a tool for squeezing the valve and retainer. Since this specialized tool is practically not found on Oka, you can buy a regular one - for the VAZ-2108, and modify it a little.

The squeeze tool consists of a tube with holes for attaching to the valve cover studs, and a handle with a curved lever (pointed at the end) connected through an axle, allowing the lever to move freely.

The tool works simply: a handle with a lever is put on the tube. It is then secured to the valve cover studs. The handle moves freely along the tube, allowing it to be positioned exactly opposite the cam. The lever is installed between the cam and the pusher; when you press the handle, it compresses the valve spring, and all that remains is to install a clamp to hold the pusher in the depressed position. You can see how everything happens in the photo below.

As for modifying the tool from the VAZ-2108 to work with the VAZ-11113, you just need to drill two through holes in the tube, the distance between which corresponds to the position of the valve cover studs of the Oka engine (it is 17.8 cm).

In general, to make the adjustment you will need:

• Set of keys (open-end, socket);
• Screwdrivers;
• Punch and tweezers;
• Tool for squeezing pushers;
• Retainer;
• Set of probes;
• A tool for accurately measuring thickness (at least a caliper);
• Washers;
• Rags;
• New valve cover gasket;

Features of the timing device

The same applies to the gas distribution mechanism. The essence of the work is identical, as is the design, but the VAZ Oka has 11113 switchgear. the shaft has only 4 cams. Therefore, the maintenance of the power plant of a small car is no different from the VAZ-2108.

The Oka uses a gas distribution mechanism with an overhead camshaft, which is installed in the engine cylinder head. This made it possible to abandon a number of components (bars, rocker arms). In this design, the camshafts. shafts act on the valves through pushers. In this case, it is necessary to have a thermal gap between the component elements (cam-pushrod-valve heel), which compensates for the change in geometric parameters occurring due to expansion of the metal as a result of heating.

But during engine operation, wear occurs on the surfaces of the cams, pushers and heels as a result of friction, which causes the thermal gap to change. Moreover, it is not necessary that it will increase; it also happens that the gap decreases. This often happens due to low-quality oil, which leads to the appearance of deposits on the working surfaces of the timing belt.

As a result of a change in the thermal gap, a violation of the valve timing occurs, which is why the power plant loses power (which the Oka already has “sparsely”), fuel consumption increases, and dynamics decrease. And all because the valves either open insufficiently (increased clearance) or do not fit tightly to the seats (reduced clearance).

To compensate for changes in the thermal gap, the VAZ-1111 uses special adjusting washers, which are placed in a special seat in the pusher. That is, the contact of the camshaft cam occurs not with the pusher, but with the installed washer.

In order for the thermal gap to meet the standard, periodic adjustment of the valves on the Oka is required. Due to the design features of the timing belt, the entire process boils down to installing washers of the required thickness.

Oka gas distribution mechanism

If you compare old VAZ classic engines with a timing chain drive, you will notice significant differences in the design of the drive. The bulky metal chain was replaced with a timing belt. The design of the cylinder block has become shorter and lighter, since the opening for the chain in the timing drive mechanism has disappeared. The designers changed the principle of opening valves, it became simpler. If on old engines the camshaft cam pressed on the valve stem through the rocker arm, now it acts on it through the adjusting washer. The thermal gap is set on a cold engine by selecting a washer of the required thickness. Manufacturers make them in different sizes, the values ​​of which are marked on the ends of the washer. If the driver adjusts the thermal gap independently, he will have to purchase a certain number of such washers, which is not always economically feasible.

The design of the timing mechanism drive is such that the belt drives the pump in the Oka engine cooling system. Often it is because of the breakdown of this pump that the toothed belt drive fails. Therefore, car manufacturers recommend that the belt drive and pump in the engine cooling system be replaced at the same time

When inspecting, you should pay attention to the condition of the tension roller in the timing mechanism.

Belt replacement procedure

The process of replacing a timing belt on Oka is not very difficult. If you carefully study the process before doing this, you can do it yourself. The work can be done on any level surface.

Before starting the operation, install wheel chocks under the rear wheels and tighten the hand brake cable. The front wheels are turned to the right as far as possible (all the way), and the battery is disconnected. The further procedure will be something like this:

In the engine compartment, remove the spare wheel and the windshield washer fluid reservoir. You will also have to dismantle the air filter housing and ignition coil. After loosening the tension on the generator set drive belt, remove it from the pulleys. After this, you can remove the protective plastic timing case. Next, rotate the crankshaft clockwise until all the timing marks in the timing drive are aligned. It is not yet possible to remove the toothed belt; the generator set drive pulley on the engine crankshaft is in the way. There is a hole on the right mudguard in the direction of travel of the car. A 19mm socket wrench is inserted into it to unscrew the bolt on the crankshaft pulley. Before doing this, you should secure the motor from turning. This can be done through a hole in the top of the flywheel housing by inserting a strong screwdriver or suitable pry bar between the flywheel teeth. An assistant should hold it. Unscrew the bolt securing the generator pulley and remove it from the shaft. Next, loosen the tension of the timing belt. To do this, you need a 17mm wrench to loosen the tension roller nut. If it is replaced, then completely remove it from the axle. There is an adjusting washer in front of the roller on the block side. If the pump in the engine cooling system is being replaced, drain the antifreeze and then remove it from the engine block. Remove the timing belt

Important! The engine cannot be cranked after this, so as not to bend the valves. Carefully inspect the condition of the timing drive pulleys, clean them of possible contamination and traces of engine oil. Installing a new timing belt is done in the reverse order. Before this, carefully check once again how the timing marks in the timing drive mechanism match. At the end of the work, manually turn the engine several times, and again check how the marks match.

At the end of the work, manually turn the engine several times, and again check how the marks match.

VAZ 11113

For ease of operation, remove the windshield washer reservoir, ignition coil and air filter housing (see the relevant sections).

1. Remove the generator drive belt (see "Replacing the generator drive belt").
2. We remove the front cover of the gas distribution mechanism (see "Adjusting the tension of the timing belt (timing belt)").
3. Turn the front wheels all the way to the right.
4. Through the hole in the front right mudguard, using a 19mm head (with an extension), turn the crankshaft clockwise by the bolt securing the generator drive pulley until the mark on the camshaft timing pulley aligns with the mounting lug on the rear cover.
5. Having removed the rubber plug in the upper part of the clutch housing, we make sure that the mark (mark) on the flywheel is located opposite the central slot of the scale of the crankshaft rear oil seal holder (the coolant supply hose to the radiator has been removed for clarity).
6. We fix the crankshaft from turning by inserting a screwdriver through the hole in the clutch housing between the flywheel teeth.
7. Unscrew the bolt securing the generator drive pulley.
8. Remove the generator drive pulley.
9. Use a 17mm wrench to loosen the tension roller nut.
10. Turn the tension roller to a position in which the belt will be loosened as much as possible.
11. We remove the timing belt from the camshaft and crankshaft pulleys and the coolant pump. ATTENTION! On a VAZ-1111 engine with the belt removed, turning the crankshaft or camshaft is unacceptable - this will lead to engine damage.
12. When replacing the tension roller, unscrew the nut securing it and remove the roller from the stud.
13. A spacer washer is installed under the roller.
14. Install the timing belt in reverse order. We check that the alignment marks of the shafts match.
15. With the generator drive pulley removed, it is convenient to control the position of the crankshaft by aligning the marks on the crankshaft toothed pulley and the oil pump cover (for clarity, the operation is shown on a disassembled engine).
16. We put the belt on the crankshaft pulley. Then we put the rear branch on the coolant pump pulley and place it behind the tension roller. We put the belt on the camshaft pulley.
17. Using a special key with pins, turn the roller counterclockwise and slightly tighten the belt. Tighten the tension roller mounting nut.
18. We screw the bolt securing the generator drive pulley into place and using the 19-inch head, turn the crankshaft two turns clockwise by the bolt.
19. We check the alignment marks of the crankshaft and camshaft. If the marks do not match, repeat the operation to install the belt. When the marks are in the correct position, we adjust the belt tension (see Adjusting the tension of the timing belt).

Which timing belt to choose

To make it easier for you to find the answer to your questions about which belt to choose or which belt is suitable, we have prepared a table for selecting timing belts for different brands and models of cars:

Timing belt options for VAZ

If you can’t decide where to buy a timing belt in Volgograd, Volzhsky or another city in the region, contact us, you can’t go wrong.

Pay special attention to how to set the timing marks. We suggest taking a little more time to watch the video of replacing the timing belt on a VAZ with a 16-valve engine

Replacing the timing belt and rollers on 16 valve VAZ 2110, 2111 and 2112

The gas distribution mechanism (GRM) of a car fills the cylinders with a new portion of fuel and is also responsible for removing exhaust gases. This process occurs in the engine cylinders using overhead valves.

The camshaft controls the operation of the valves. It is located at the very top of the valves and rotates from the crankshaft using a toothed belt, which in addition to them also drives the water pump (pump).

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

Oka timing belt break at 10,000 km

In this video

I'll tell you in detail how to set the timing marks
on
the
eye
. If anyone wants to help develop the channel, here's a qiwi.

1. Make sure the crankshaft gear timing marking is properly aligned with the oil pump housing hazard.

1. Temporarily reinstall the crankshaft pulley bolt to allow the crank to rotate.

1. Loosen the tensioner nut, unfold the tensioner assembly and remove the timing belt.

Typical drive belt problems

1. Carefully examine the condition of the removed belt; in case of defects (see Illustration Typical drive belt malfunctions
   ), replace it.

1. Manually check the tension roller for free rotation.

1. Assess the condition of the tensioner spring.
2. Defective components are replaced.

1. Make sure the engine is still at TDC at the end of the compression stroke of the first cylinder piston.

1. Reinstall the spring tensioner.

If the retaining pin is removed, its threaded portion must be lubricated with retaining sealant before being screwed into the engine block.

Using a rod wrench, unscrew the tensioner and temporarily tighten the locknut.

After making sure the timing marks are correctly aligned, install the belt. The white lines on the tape should be aligned with the point markings on the distributor gears and crankshafts. Make sure the belt is installed with the arrow pointing away from the engine (front cover of the case).

Infiniti QX4 models equipped with the 3.3-liter engine use a 133-tooth timing belt in this manual. When installed between the camshaft gears, 40 belt teeth, between the wheels of the left distributor and the crankshaft. 43 teeth

Hold the tensioner with a wrench and loosen the nut securing it.

Using a wrench, turn the tensioner 70-80 degrees clockwise and temporarily tighten the nut again.

Rotate the crankshaft clockwise at least two full turns, finally bringing it to the TDC position at the end of the compression stroke of the first cylinder piston.

Press the belt in the area between the right camshaft sprocket and the tension roller with a force of 98 N (10 kG)

.

Fill the probe with a 0.35mm

and a width of 1
2.7 mm
in the gap between the belt belt and the tension roller.

While slowly turning the crankshaft clockwise, retract the dipstick blade completely under the tape.

When turning the shaft, the belt should move approximately 2.5 teeth.

The gas distribution mechanism (GRM) of a car fills the cylinders with a new portion of fuel and is also responsible for removing exhaust gases. This process occurs in the engine cylinders using overhead valves.

The camshaft controls the operation of the valves. It is located at the very top of the valves and rotates from the crankshaft using a toothed belt, which in addition to them also drives the water pump (pump).

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

About the engine

For these models, engines 2108 and 21083 were taken as the basis. They are 2-cylinder engines with an in-line vertical arrangement of cylinders. The camshaft is installed in the cylinder head. The working volume is 649 cm 3 and 749 cm 3. The increase in volume is obtained by increasing the diameter of the pistons from 76 mm to 82 mm. The cylinder blocks of these engines, heads, flywheels, and pulleys are different.

Many spare parts are unified with their 4-cylinder variants. The power supply system is carburetor, but with changed calibration data. In 1990, the timing belt on the power unit was replaced. If the previous product had semicircular teeth, then on the new one they began to have a trapezoidal shape with a groove at the top of the tooth. The pulleys were changed to match the tooth profile, but the belts themselves are interchangeable; you can use both new and old parts.

It is possible to obtain maximum efficiency from using an internal combustion engine only with the correct adjustment of the valve timing. There are marks on the timing drive for this purpose. One of them is the protrusion on the rear cover for the drive belt protection, which should coincide with the mark on the camshaft pulley. The second mark is located at the bottom of the cylinder block, and it coincides with the mark on the crankshaft pulley. The piston of the first cylinder should be at top dead center at this time.

Are the valves bending?

This question worries many owners, since after such an “incident” a costly overhaul of the power unit will follow. Mechanics know of cases where, after the pistons met the valves, in addition to bent valves, the piston heads were damaged and the guide bushings in the cylinder head were destroyed. The engine, based on the VAZ 21083 engine, is free from such shortcomings. The pistons of this internal combustion engine have recesses that prevent the valve head from meeting the upward-moving piston.

This problem can occur in two cases:

• Cutting teeth on the timing belt.
• The alignment marks on the engine being repaired are not aligned correctly.

To avoid this, you should carefully study the process of replacing the belt, or seek help from service center specialists.

DO IT YOURSELF! Adjusting idle speed and ignition on the road! Ignition distributor for Oka. DOWN. Replacing the ignition coil on an oka

Will the valves bend?

This question is sometimes almost the main one. Some motorists refuse to buy a car if the valves on the engine bend when the belt breaks. This is understandable, since after this you have to completely repair the cylinder head. And this pleasure is not very cheap. It must be said right away that on engines based on 21083, the valves do not bend. There are recesses at the top of the pistons that prevent them from hitting the valves (arrows point to them in the photo).

But on the 2108 motor there is a bending problem and it can arise in the following cases:

1. If the teeth on the drive belt are cut off.
2. If the marks on the shaft pulleys are set incorrectly.

To prevent breakage, you need to change the belt correctly. Any motorist who knows how to handle wrenches can replace the timing belt on the Oka.

OKA ignition system

Ignition system of Oka, VAZ 2109.
How to set the ignition on Oka

If Oka's car does not start the first time, then you need to set the ignition correctly. Also, the proper functioning of the ignition affects fuel consumption and the overall dynamics of the vehicle.

First, remove the air filter. You only need to check the ignition timing when the engine is idling. The crankshaft rotation speed should be 820–900 rpm. The advance angle should not deviate more than 1° from top dead center.

Other announcements on the topic:

The ignition system is one of the main systems of a car. If the ignition timing is set incorrectly, the engine will begin to overheat, will not develop full power, fuel consumption will increase significantly, and detonation will appear. To check the ignition timing, you can

Read

Correct setting of the ignition timing in a contactless ignition system makes it possible to operate the car in comfortable conditions. Otherwise, the engine does not develop full power and fuel consumption increases. You can set the contactless ignition not only to 100, but

The normal operation of a car engine depends on the correct ignition timing. Otherwise, fuel consumption increases, the vehicle's thrust decreases, and pistons, connecting rods and piston pins are destroyed. You should inspect its installation from time to time in order to always be

https://youtube.com/watch?v=jXTcxsl8ON0

Troit Oka

.
Setting the ignition on the Oka
.
Oka
carburetor .

https://youtube.com/watch?v=Kcomcxmgf3g

We set the timing marks

In this video

I'll tell you in detail how to
set
the timing marks on
the eye
. If anyone wants to help develop the channel, here's a qiwi.

The operation of a car engine is impossible without correctly set ignition timing. This is noticeable not only when starting it with the starter, but also when driving. Increased discomfort is created from uneven operation, a drop in engine power, increased fuel consumption and, most importantly, the car

The car's ignition system is one of the main ones. Without it, there is no way to start the engine and start driving. In addition, incorrectly set ignition timing not only causes discomfort when driving a car, but also contributes to increased fuel consumption, and in some cases

Read

Ignition problems quite often occur on VAZ cars. That is why experienced motorists have developed several methods with which you can quickly and easily adjust the ignition of a VAZ. Since adjustment can take a long time, quite often it is only done

Perhaps, one of the ways to most accurately determine for yourself the correctness of the ignition timing set in a car engine is to determine the specified parameter using a strobe light, which is always available for sale in any store that sells vehicles.

The ignition timing in a car is determined by the angle of rotation of the crankshaft from the moment the spark appears at the spark plug to the position of the piston at top dead center. The ignition angle is lost due to a poorly tensioned chain or a twisted belt. For good engine operation it is necessary to set the angle

For reliable operation of the Buran snowmobile engine in difficult operating conditions, it is necessary to correctly adjust the ignition system. The most important parameter that has to be taken into account when adjusting is the ignition timing setting. As a rule, even the factory setting

>

Replacement timing

The vehicle operation regulations recommend that owners check the condition of the belt drive and belt tension after a run of 30 thousand km (more often). It is recommended to replace it after 60 thousand km. If the car owner does not change the belt within this period, it may be destroyed.

It is not allowed to operate the Oka with traces of engine oil leaks in the area where the toothed belt operates. It has a bad effect on the belt material and accelerates its destruction. Engine oil leaks should be repaired and the toothed belt replaced with a new spare part. If you carry out maintenance work on the power unit in a timely manner and with high quality, then there will be no problems for the owner.

That's how the pump makes noise. Oka VAZ 1111

How to change the timing belt on an Oke video

Do not bend or twist the belt!

After removing the timing belt, do not rotate the crankshaft and camshafts to avoid damage to the internal components of the engine as a result of the valves hitting the piston bottoms!

Before installing the belt, thoroughly clean all timing gears, completely removing dirt, grease and moisture from them!

The timing belt must be installed on a cold engine!

Timing drive components installation details

1. Apply the parking brake, support the rear wheels with wheel chocks, then jack up the front of the car and place it on stands (see illustration Diagram of setting up the stands to secure the vehicle in a raised position
   ). If equipped accordingly, remove the crankcase protection.
2. Drain the radiator - try not to let coolant get on the drive belts.
3. Remove the radiator.
4. Remove the cooling fan and water pump pulley.
5. Remove the drive belts for the steering pump, AC compressor and generator.
6. Remove all spark plugs.
7. Remove the distributor protective screen.
8. Remove the support bracket for the intermediate roller of the AC compressor drive belt.
9. Remove the tube connecting the timing cover to the air intake hose.
10. Remove the coolant hose connected to the thermostat.

1. By turning the crankshaft by the bolt of its pulley, bring the engine to the TDC position of the end of the compression stroke of the piston of the first cylinder.

1. Remove the crankshaft pulley bolt and remove the crankshaft pulley using a suitable puller.
2. Remove the upper and lower sections of the front timing cover.
3. Make sure that the dot alignment mark of the left camshaft gear is aligned with the matching mark on the upper section of the rear timing cover.

Replacing the timing belt VAZ 11113 Oka

Replacing the timing belt VAZ 11113 Oka

now there are a lot of left belts

on the market, so buy only brands and there will be no problems. Although I came across that.

Good evening everyone. It’s slowly freezing outside, today it was 20 degrees in some places. The window was whispering slowly, in the evening I decided to warm it up, it started up normally, the panel showed -15 degrees. Who knows why this happened with the timing marks. The 1st photo shows how it should be, the 2nd photo shows how my timing marks are at the moment. The discrepancy turns out to be 2 teeth, I do it as expected and it won’t start. If anyone has encountered this, I would be glad to hear comments on this issue. Good luck everyone with your cars.

Price tag: 0 ₽ Mileage: 111805 km

Will the valves bend?

This question is sometimes almost the main one. Some motorists refuse to buy a car if the valves on the engine bend when the belt breaks. This is understandable, since after this you have to completely repair the cylinder head. And this pleasure is not very cheap. It must be said right away that on engines based on 21083, the valves do not bend. There are recesses at the top of the pistons that prevent them from hitting the valves (arrows point to them in the photo).

But on the 2108 motor there is a bending problem and it can arise in the following cases:

1. If the teeth on the drive belt are cut off.
2. If the marks on the shaft pulleys are set incorrectly.

To prevent breakage, you need to change the belt correctly. Any motorist who knows how to handle wrenches can replace the timing belt on the Oka.

A few words about the Oka engine

The engines used as the basis were models 2108 and 21083. There are only two cylinders in Oka engines, they are arranged vertically in a row. The camshaft is located in the cylinder head, engine capacity is 649 and 749 cc. cm respectively. The increase in volume was achieved by increasing the diameter of the pistons by 6 mm (from 76 to 82). As you can understand, motors have different blocks, flywheels, pulleys, and heads.

But it should be noted that most of the parts are unified with the 4-boiler options. The engine is powered by carburetors. On cars after 1990, they began to install not semicircular teeth on the timing pulley, but trapezoidal ones.

To increase the efficiency of the motor, you need to properly configure the timing mechanism. To do this, you need to align all its pulleys strictly according to the marks on the rear cover opposite the camshaft and on the crankshaft pulley.

Occasionally, the timing belt breaks at 10,000 km. Replacing the timing belt and rollers on 16 valve VAZ 2110, 2111 and 2112. This is how the pump knocks. Oka VAZ 1111

How to replace the belt on the Oka?

Difficulties should not arise when replacing the timing belt on the Oka if the procedure was always carried out in a timely and correct manner. All repair work must be carried out on a flat surface. First, place wheel chocks under the rear wheels to prevent the car from rolling.

Next you need to perform the following manipulations:

1. Remove the spare tire and washer water tank from the engine compartment. You will also need to remove the air filter housing and the ignition coil.
2. Loosen the tension on the alternator belt and remove it.
3. Remove the plastic casing that covers the drive.
4. Rotate the crankshaft clockwise to align all marks.
5. Install the socket 19 through the hole on the right mudguard onto the crankshaft pulley bolt. To unscrew it, you need to secure the engine from turning. To do this, put an assistant in the car, he must press the brake pedal with 4th and 5th speed engaged.

Springs

Springs (outer 16 and inner 17) press the valve to the seat and do not allow the valve pusher to come off the actuator. The lower ends of the springs rest on the support washer 18 springs. The upper support plate 15 of the valve springs is held on the valve stem by two valve nuts 14, which when folded have the shape of a truncated cone. The cotters have three internal flanges that fit into the corresponding recesses on the valve stems. This design provides both a reliable connection and the ability to rotate the valves during operation, so they wear more evenly.