How to make heated seats on a car? -

Welcome to the kuzov.info blog!
In this article we will figure out how to make heated seats in a car. Let's look at what kits there are for installing heated seats, their advantages and disadvantages. This will help you decide which kit is best to choose for your car. The principle of operation of heated seats, the process of installing and connecting heating elements, and advice on proper operation are given here.

Heated seats are a good addition to a car, increasing comfort, and are installed on expensive cars or on any model as an additional option. If the vehicle is not equipped with heated seats, a kit for installing heated seats can be purchased separately. This can be either a soft substrate with heating elements inside, which is installed on top of the seat upholstery and connected to the cigarette lighter, or a kit for installation under the seat upholstery. In this article we will look at how to make heated seats using a kit that is installed under any seat upholstery (artificial, natural leather or textile). These are very thin heating elements, about 1.5 mm thick, which are not felt at all until they are turned on.

The content of the article:

What types of heated seats are there?
How does heated seats work?
Preparing to install heated seats
Removing seats and upholstery
Installation of heating elements
Connecting the heated seat wiring
Assembly, installation and testing of heated seats

This article is of a general nature and will be useful as instructions for installing heated seats on any car. In the description of the installation kit you can read that it is intended for professional installation by an experienced specialist. However, the installation process is also accessible to a simple car enthusiast. It is important to carefully study the information provided in this article and do everything consistently and carefully. This can take several hours or two weekends, depending on the skills and efficiency of the installer.

What types of heated seats are there?

There are 2 types of seat heating kits: with a copper heating element and with a carbon fiber heating element (carbon fiber/carbon thread).

Seat heating kits are available in 12V and 24V versions.

Seat heating kit with copper wire heating element

A seat heater with a copper heating element is one long zigzag wire where one end has a positive polarity and the other end has a negative polarity, similar to the filament in a light bulb, which also gets hot.

Heated seats with a copper heating element have the following advantages:

The copper heating element heats up quickly.
Heated seats with a copper wire heating element reach a higher temperature than carbon fiber ones.

Disadvantages of heating with a copper heating element:

The disadvantage is that the rapid heating and cooling cycles will thin the wire and eventually it will burn out.
Since the copper wire heating element cannot be cut to fit any seat, there are no universal kits that will fit all vehicles. Various sets with a copper heating element are sold for specific car models, or for specific seat sizes. If you are going to install a seat warmer kit with a wire heating element, it must be designed specifically for your car model (to fit), or be smaller than the car seats.

Seat heating kit with carbon fiber heating element (carbon fiber/carbon thread)

The carbon fiber (carbon fiber) heating element has a honeycomb structure. Electrodes (positive and negative) are located at the edges of the heating pad, cells made of carbon fiber are located between these electrodes.

Sets with a carbon heating element have many advantages:

The heating element of such heating is a carbon (carbon fiber) thread, which is much stronger than copper wire.
The honeycomb structure makes the heating substrate very reliable. Damage to a single cell does not disable the functionality of the entire heating system.
Heating elements in the form of carbon fiber can be trimmed with scissors to reduce the size and fit it to a specific seat. This makes the seat heating kit with carbon heating element universal.

Disadvantages of sets with a carbon heating element:

Carbon filament takes longer to heat up (about 1-2 minutes longer than a copper wire heating element).
The carbon heating element heats up to a lower temperature (about 5 degrees lower than the copper heating element).
Heating with carbon wire reaches the highest temperature of 50-57 degrees and the lowest 43-51 degrees Celsius, which is slightly lower than the copper wire element.

As can be seen from the listed advantages and disadvantages, heated seats with a carbon heating element are more preferable, as they are a universal and reliable option. In addition to universal kits, you can also find a seat heating kit specifically for your car on sale. It will fully match the seat configuration of your car, and will have detailed instructions for connecting to your vehicle. The universal kit may need to be adjusted to the location by trimming the lining with heating elements.

Materials for self-production of heaters

The cheapest way to get heated car seats is to make it yourself. For production you will need the following materials:

heating wire;
heat shrink insulating tube;
thick fabric;
connecting wires;
fuse block, buttons or plug for the cigarette lighter socket.

The main question is which wire to use to make the heater. The simplest option is to buy a ready-made heating cable, but such a solution is associated with financial costs. It is cheaper to make the element yourself using the following materials:

thin high-resistance wire made of chromium-nickel alloy (in common parlance - nichrome);
LAN wires - a cable used to connect to the Internet (the second name is twisted pair);
thin copper wires from any other cables.

The length of the conductor for homemade heating is determined by the resistance of the section. Based on the power of each built-in element of 40 W, we obtain the required resistance of about 4 Ohms at a supply voltage of 12 volts. Connect the first clamp of the multimeter to the end of the wire, and use the second to determine the length of the heating circuit: move the contact until the display shows a value of 4 ohms.

Advice. If the conductor is covered with insulation, calculate the resistivity per 1 m length by measuring the entire section and dividing the reading by the meter. Then tap off the required amount of cable with a tape measure.

If you need to splice pieces of wire together to create the required resistance, connect the ends of the copper strands by soldering. Nichrome wire will have to be selected in one piece, since it can only be connected by welding.

How does heated seats work?

The technology used to operate heated seats is not too complicated. Heated seats work by placing heating elements under the car seat upholstery. Electricity is passed through the heating element. A heating element can be thought of as a resistor because electricity flowing through it receives resistance and produces heat.
Like many systems in a car, heated seats are activated using a relay switch. A relay switch is a relatively simple mechanical trigger that allows a device to begin receiving power. A relay allows electricity to switch circuits from less power to more power.
A thermostat is included in the heated seats as a precaution against overheating. If there is no thermostat, then after starting the heating element will continue to heat up indefinitely. This will cause overheating, which may cause fire, injury or damage to the vehicle. As a safety precaution, the thermostat serves as a heat limiter. Once the heating reaches the temperature set on the thermostat, power to the relay is turned off until the seats have cooled to a certain temperature. The thermostat controls both overheating and underheating. The control unit in the form of a mode switch controls the thermostat settings.

The best external seat heating systems

Most often, car owners choose the following products:

Model name	Heating elements	Peculiarities	Cost, rub
"Thermosoft"	Thermal fibers Fiber Thermetics	Does not deform even when bent 180 degrees. Attached with rubber bands.	2 100
Waeco	Teflon sheathed wire	Equipped with a thermostat to prevent overheating.	1 900
"Emelya 2"	Carbon fiber	Uniform heating, ability to operate in 4 modes.	from 900

There are also special covers that are used for child seats. Among them it is worth highlighting:

Model name	Dimensions, mm	Peculiarities	Cost, rub
"Emelka"	720 x 320	Equipped with a microprocessor-type regulator. Overheat protection.	1 300
Warmkid	550 x 270	Automatic shutdown at a temperature of +40 degrees.	1 000

In addition to capes and covers, there are also stationary heating systems, which are considered more reliable and durable.

Included in the package

Pads with heating elements for the two front seats (lower and back), wiring and switches.
Wiring includes thermostatic regulator, fuse holder with 12v fuse, and relay.
Zip ties and adhesive tape.
The kit usually contains everything needed for a standard installation of a heated seat kit. If you need any electrical elements (connectors, corrugation, etc.), you can purchase them in addition.

What tools will you need:

Phillips and flathead screwdriver
Ratchet wrench with head for removing seats
Stripping pliers
Crimper
Nippers or metal scissors (for cutting the rings holding the upholstery).
Bladed knife or scissors
step drill
soldering iron with solder and solder paste
marker
scissors
multimeter, 12V electrical tester with light bulb.

The photo shows a universal set of seat heating with carbon heating elements in the form of a cellular structure.
Such sets are sold both on Aliexpress and in other online and off-line stores. Additional accessories and installation kits are not required for most installations, but are used by professional installers.

Preparing to install heated seats

First, disconnect the battery and let the car sit for 10-20 minutes to allow the SRS to fully discharge. Once the airbag (SRS) related connectors have been disconnected, the battery must not be reconnected until you turn on all SRS components again, otherwise an error will occur.

On vehicles with seats that have side airbags, you must follow a certain procedure before removing the seats to avoid an error (may not work on all vehicles):

Turn off the car and leave the key in the ignition off.
Disconnect the negative terminal of the battery and insulate it with a rag or plastic bag so that it does not accidentally reconnect. You must wait at least 5 minutes before proceeding to the next step.
Remove the seats, disconnect the airbags, seat belts, power connectors for the power seats. Do not turn on the ignition while the seat is removed and all connectors are disconnected.
When the seat is installed and screwed into place and all connectors are connected (the ignition key must be in the off position), connect the negative cable to the battery.

If the seats have side airbags, then before removing the seats you need to disconnect the negative terminal of the battery to avoid an error.

So, let's first look at the brief installation instructions, and then we will analyze each point in detail.

Dismantling works

To install heating elements, you first need to carry out a dismantling procedure. It includes the following activities.

Unscrew the plastic fasteners that connect the seats to the body of your car.
Remove the skids. Two pieces are located in front, and two more are located in the back.
Remove the chairs from the interior, otherwise it will be extremely uncomfortable to work.
Separate the back from the chair. To do this, there are bolts on the sides, which can be removed with a 10 mm wrench.
On the back there is a plug for the headrests, which can be removed.
The upholstery is removed from the hooks below. To do this, the hooks are slightly unbent.
Now you can completely remove all the trim.
Carry out a similar procedure with the second seat if you plan to install heating on it too.

Installation instructions:

Disconnect the negative battery terminal.

Remove the seats from the interior.
Remove the upholstery.
Place a pad with heating elements on the back and seat.
Identify a power resource that is capable of delivering a continuous 10 amps of current. Once you have determined the power resource, wire to that resource.
Find a suitable location for the switch. Drill a hole in the desired location and pull a connector through the hole, then connect it to the switch and attach it.
Place the seats in place in the interior and fasten them. Connect all connectors under the seat, along with the new heater connector.
Connect the battery and turn on the ignition.
Check heating in all modes.

Heating capes

Not all local heaters require installation. After all, in the southern regions of the country you can get by with temporary devices. In this case, a temporary heated car seat cover is quite suitable. Its installation does not require major alterations in the interior. It is most often connected through the cigarette lighter socket.

The most common countries producing this product are:

Poland;
Germany;
China.

Product weight is from 0.6 to 0.9 kg. Heating can be either only for the lower part of the chair, or complex, including a warm “back”. With this design, the seat heating button is not located on the cable connected to the power outlet. No installation is required.

Covers for heated seats

pros

minimum cost;
can only be purchased for one driver's seat;
quick installation and dismantling;
large selection of manufacturers;
To turn it on, you do not need to remove separate wires; the cigarette lighter socket is enough;
several preset modes;
a large number of colors and styles.

Minuses

not entirely aesthetically pleasing;
for the second seat you need an additional connector in the cigarette lighter or a “tee”;
Often you come across low-quality fakes that quickly fail.

Removing the seats

Disconnect the battery terminal before disconnecting the seat. Otherwise, the airbag error will light up (if the seat has one). Disconnect power from the seat last.

The seat is attached to the car floor with 4 14 mm bolts. The rear bolts are covered with plastic covering.

The plastic needs to be removed and the bolts unscrewed.

To make it easier to remove the seats, remove the headrests, seat belts and anything else that prevents the removal of the seats.

The removed seat is easy enough to stick out of the cabin. Start pulling it out from the back. Be careful as the metal runners have sharp edges that can damage the plastic. It is better to place the seat on some kind of elevation (a bench or table) to make it more convenient to work with it. Lay or place something under the seat as the metal runners can damage the surface. Remove all side plastic covers.

Convenient alternative: replacing the car seat

The most convenient - but also the most expensive - option for installing a seat heater in a car is to replace the entire seat with an analog one, but with a heating function.

Suitable car seats with heated seats can be purchased at a salvage yard. Depending on the time of year, a set of two seats will cost from 5 to 30, 60 thousand rubles or even more: baza.drom.ru

The following rule also applies here: if the seat is fitted with a side airbag, removal and installation must only be carried out by a specialist. The price is usually negotiable.

Removing the seat upholstery

To install a seat heater, you need to gain access under the seat upholstery and backrest. To begin removing the upholstery from the seat, you need to remove all the metal rings (hog rings) that hold the upholstery. Start at the bottom back of the seat. Turn the seat over for better access and start cutting off the rings with wire cutters.

The instruction manual, which can be purchased or downloaded on the Internet, may be useful during disassembly. The service instructions may contain information about disassembling the seat (removing the upholstery), the location of all fasteners.

When disassembling the seat, take a photo before you remove anything, so that later, when reassembling, you can look at the photo as a hint.

Once the edges of the upholstery are free, lift up the edge of the upholstery to gain access under the upholstery and begin cutting away the fasteners (rings) that secure the center section of the upholstery. Instead of fastening rings, you can use small ties. Clean the surface of the soft part of the seat, as the heating will stick to the seat.

The seat back may have 2 brackets for attaching the headrest. There is no need to remove them, as they will not interfere with the heating installation. They may also break when removed.

Installation of heating elements

The installation process for the driver and passenger seats is the same, with the exception of one feature, which we will discuss below.
After installing the heated seats, the only visible thing should be the heating mode switch.
The heated pad is placed between the seat upholstery and the seat cushion.
For the longevity and reliability of the heating elements, it is important that they are positioned correctly. Heating elements can only be placed in the middle of the seat. They should not go into the lateral support. Heating elements must be installed without folds.
The pads can be trimmed slightly in length (the edge opposite the edge with the wiring) so that they fit well in place. Seal the edge using the adhesive tape included in the kit. You cannot cut the heated pad too wide. You can see how the long wire along the edges shows through - it cannot be cut. It is allowed to trim the edges a little to this wire. This may need to be done so that the heating elements do not come into contact with the side seams.

Place the heating element intended for the seat and align it on the soft part of the seat. Use a marker to mark the location of the upholstery attachment points (rings or others). Using scissors, cut holes in the heating pad for these fasteners. Cut several strips of tape and cover the exposed ends of the heating elements around the hole.

The pad with heating elements has a double-sided adhesive tape for fastening under the upholstery, on the soft part of the seat.

If the seat has recessed channels, then the heating element cannot be pushed into them. You need to cut out a heating lining for them in the places where the heating elements are located, having previously marked these places with a marker. After this, the exposed edges of the heating element must be insulated by gluing the tape from the kit.
Never cut holes in an area covered with tape. Areas with adhesive tape should only be applied to a flat seat surface.
The heating element should not touch any conductive surfaces (metal rings - upholstery fasteners, seat frame) to avoid a short circuit.
The old, classic fastenings are metal rings, while the new, more modern ones are Velcro fastenings. For older fasteners, apply the included tape around the rod to insulate it. Velcro fastenings can be sewn onto the lining with heating elements. Thus, there is no need to cut heating elements for this type of mount.
The soft seat backing must be clean before installing the heating.
Peel off the protective layer from the back of the adhesive part of the heated pad and carefully apply it to the seat in the desired position. The strength of the heated adhesive joint is achieved by applying sufficient pressure. The heating element cannot be separated and rearranged after gluing.

Universal heating elements must be cut out at the places where the upholstery is attached. Exposed edges must be sealed with adhesive tape included in the installation kit.

The passenger seat may have a sensor that responds to the passenger's weight to activate or disable the passenger-side airbags in the event of an accident (Occupant Detection System). After removing the seat upholstery, you need to determine whether there are sensors located on top of the seat. Toyota, Kia and Hyundai usually place the sensors on the surface of the seats (bottom). Honda usually places the sensors on the back of the seat. Heating cannot be installed on top of this sensor. In this case, you can install heating only on the part of the seat where there is no sensor (the back or vice versa, only the seat). Also made at the factory. When you buy a Toyota car with such a sensor, from the factory it only has heated backrests of the passenger seat. When you purchase a Honda, from the factory it only has heated seats, and the backrest is not heated (since the sensor is located on the backrest).
It may be necessary to cut a channel for the temperature controller and wire with a knife in the soft part of the seat so that it is not noticeable after installing and assembling the seat.

The best built-in systems

To choose high-quality seat heating, you should pay attention to the following brands:

Model name	Peculiarities	Cost, rub
Waeco MSH-300	Heating is carried out by carbon elements. An electronic power supply is installed that allows the system to operate in 3 modes.	16 000
"Emelya UK2"	Wire type heaters. There are 8 working modes. Equipped with a spark protection system.	4 000
"Emelya UK"	The most budget option. 2 heating modes.	1 4000

There are no permanent systems for child seats, since such installation of heated seats will be fraught with many difficulties. However, if necessary, you can make a heater for any type of seat yourself.

Connecting the heated seat wiring

It will be more convenient to conduct wiring from the seats to the power source when the seats are removed and located outside the cabin.
The wiring must have a reserve length and be stretched so that you can change the position of the seat without any difficulties. The cable should not touch sharp edges, bend or be strained to avoid damage.
Think about where you can hide the heating wiring. The most suitable places are under the center console, which is located between the front seats, under the carpet, at the edge of the footrest, or in the place where the threshold is located.
Study the heating connection diagram, which is in the instructions, as well as the wiring diagram of your car. You need power for the heated seats that will turn off completely when the ignition key is removed.

Simplified connection diagram for seat heating

The positive (usually red wire) can be connected to the positive ignition power supply.
Securely connect the ground (black wire) with a small terminal to the body negative (ground). Improper grounding may cause the heating to not work.
Select a suitable location for mounting the switch that is easily accessible to the driver and passenger, and ensure that there is enough space behind the switch for the wiring and switch bracket. This could be on the side of the seat, on the front of the dashboard, or on the panel that runs between the driver and passenger seats. Mark the location and drill approximately a 20mm hole to install the switch. The hole should not be too small or too large. This is important for securely attaching the switch. The most suitable place for the switch is on the plastic trim located on the side of the seat.

Select a location that is easily accessible to the driver and passenger to install the switch.

Correct choice of factory models

The range of products offered on the market is quite wide. You can choose kits for installing heated rear and front seats from both domestic and foreign manufacturers. The following products are popular and in demand:

Megalight (Taiwan);
Weaco (Germany);
“Emelya” “Teplodom” (Russia);
Autoline International (China).

Russian and European models are more reliable. Although they are a little more expensive, they have design advantages, which include a switch for several operating modes, built-in overheat protection, and a short circuit fuse. It is good practice to use carbon fiber or protected armored cable as a heater.

Important! During operation, it is necessary that the heated seat cover is not exposed to wet conditions, its connection cord does not have hard kinks, and excessive cable tension is not allowed.

Assembly and installation of seats

To install the upholstery on the lower part of the seat, you can use vinyl ties instead of cut rings. Insert the zip ties into the places where there were rings holding the upholstery, but do not tighten them yet. Pull the zip ties through the holes. Starting at the back, connect the zip ties and tighten them a little so they don't come apart again. Once all the zip ties are connected, tighten them and cut off the remainder. To install the upholstery on the backrest, turn the upholstery inside out and begin to gradually tighten it, unrolling it down onto the backrest. Disassembling and assembling a car seat is also described in the article “do-it-yourself seat reupholstery.”

After assembly, the seats are installed back into the cabin, all connectors are connected, including the new one going to the heated seats. Next, you can connect the negative terminal of the battery, turn on the ignition and test the heated seats.

Buy or make?

On the modern market of auto parts and accessories, you can easily find removable heating covers (capes) and even entire heated seats. Their low cost and ease of connection are undoubted advantages, therefore, if finances allow, as they say, do not show off and buy a ready-made option.

Of course, if there is no money for it, you will have to do everything yourself.

What you will need.

Nichrome wire 0.5 mm in diameter and 10 meters long.
Relay.
Button.
Wires and connectors for mounting the heater in a car.