How to set the time on the key fob Sherkhan Magikar Logikar 2, 4, 7 and 9

Of the entire range of alarms with auto-start from Scher-Khan, the most unsuccessful is definitely Magicar 5. This is due not only and not so much to the vulnerability to hacking common to all Scher-Khan systems of these years, but also to the extremely illogical implementation of auto-start. Even the classic and most convenient “software neutral” for raising the handbrake cannot be physically implemented here; there is no input for the handbrake.

In the same way, the most accurate analog method of monitoring engine operation using a tachometer signal is not provided. Therefore, the best recommendation for owners of such systems would be to replace them with more modern ones that work adequately with autostart and code grabbers that are resistant to hacking.

However, many motorists continue to use previously installed (usually in car dealerships) Magicar 5, and during operation, questions inevitably arise - from how to set up the Sherkhan Magicar 5 key fob to how to disable autostart on Magicar 5 (by the way, the correct reading is “magikar”).

magicar alarm system how to set the time on the key fob

Sometimes the time readings of the Scher Khan car alarm models Universe, Magicar, Logicar go astray. This happens for the following reasons.

weak power supply. During operation, the battery gradually discharges, losing its capacity. The clock readings are off;
recent battery change, after which the time is automatically reset;
poor contact contact. Inspect the working connections, if necessary, bend them;
manufacturing defects;
short circuit caused by the remote control getting into water or other liquid.

You can set the clock on the anti-theft system key fob yourself by following simple instructions.

Setting the clock on the Scher Khan key fob

It happens that time readings in car alarms Scher Khan Universe, Magicar, Logicar are confused. This may be for the following reasons.

low power consumption. During operation, the battery gradually discharges and loses its capacity. The clock indicators go out;
last battery replacement, after which the time is automatically reset;
poor contact between contacts. Check the working connections and adjust if necessary;
manufacturing defects;
short circuit caused by immersing the remote control in water or other liquid.

You can set the clock on your anti-theft system keychain yourself by following simple instructions.

Universal method

This scheme is suitable for Mobiscar 1, 2, as well as Mobicar A, B.

Enter settings by pressing for 2 seconds. buttons II and III. A symbol will appear on the Pro9 screen and the key fob will beep.
Press the I key once. The current time setting mode will turn on. The dial will start flashing. The remote control will sound.
Use the I button to change the hours.
Use key II to set the minutes.
Press II and III for 2 s and you will exit programming.

On the keychain Sherkhan Magikar 7

The instructions allow you to set the clock not only on the Magicar 7 key fob, but also on 11,12, 10 Mini.

Setting the current time begins with entering the remote control programming mode. This is done by pressing for two seconds. keys I and III. Confirmation of actions - the inscription Pro9 and a tone signal from the remote control.
After successful completion of the first step, an automatic switch to the time setting occurs. The dial should flash.
Button I changes the clock readings.
II changes the minutes.
Exit the regulation mode by pressing for 2 seconds. buttons I and III.

Setting the time, autorun by time

timer start (A); turbo timer mode (B); passive activation of the system (C); automatic switching mode without pressing buttons (D); siren on (E); Shock detection sensor (F) is turned off; vibration alert is active in the key fob (G); door lock control after ignition start (H); open trunk lid (J); the engine is switched on in autostart mode (K); system state (L); open doors (M); field for displaying the clock, temperature and data during autostart (N); Valet (O) operating mode; working hazard warning lights or lights not turned off (P); shock sensor (Q) triggered; key fob battery indicator (R); signal level (S).

Since the alarm system has a timed autostart mode, when the car starts every day at a given time, for it to work, you must correctly set the time on the main key fob. The procedure required to set the time on the Sherkhan Magikar 5 alarm key fob:

1. Press buttons 2 and 3 for 2 seconds. The screen indication will change to something that looks like “Pro9” (this should actually show Prog, but due to the limitations of seven-segment screen elements, it appears that way).

2. Briefly press button 1 - the current time readings will start flashing, the key fob will give a single signal.

3. Press button 2 to set the hour, and use button 3 to enter minutes.

4. Press buttons 2 and 3 for two seconds and save the settings.

Timed autostart (of course, all necessary connections and settings of the system itself must be made in advance) is possible in two options. Either the car starts every day at a set time (for which the clock is set), or this happens every 2, 4, 8 hours from the moment the mode is activated and regardless of the clock setting. The type of timed autorun is set in the system settings, that is, several options cannot be activated at the same time.

To enable autorun on a 24-hour timer, you need to:

1. Press buttons 2 and 3 for 2 seconds.

2. After the inscription “Pro9” appears, briefly press button 2 (not 1, as for setting the current time. The readings of the previously set autostart time will begin to blink.

Read also: Original Chevrolet Cruze windshield

3. Use button 1 to set the hour, button 2 to set the minutes.

4. Press 2 and 3 again and save the timer values.

5. Press buttons 2 and 4 so that the R indicator turns on on the screen.

If you need to change the autorun time when the timer is already activated, you must first turn it off (similarly, by pressing 2+4), configure the timer time, then turn it back on.

If the alarm settings are set to start periodically, simply press buttons 2+4 to turn it on and off. After activating the periodic start mode for the first time, the engine will start after 2, 4 or 8 hours, depending on the settings of the central unit.

Video: SCHER-KHAN MAGICAR 5

How to set 24 hours

In some cases, inexperienced car owners are faced with the problem of converting the clock time format. In most models, it is enough to perform a few simple manipulations to display the time on the display from 12-hour to 24-hour format. This option is more familiar and user-friendly. However, it will not be possible to set the clock on Sherkhan Magikar 5 this way, which is due to the lack of a 24-hour format in the settings.

To better understand the existing option for displaying hours and minutes, and also not to encounter various problems, you need to consider the following nuances:

The display will always show 1 of the modes next to the time: AM, PM. The first indicates the hours from midnight to noon, and the second from 12 noon to 12 midnight.
When setting the autostart timer, you need to be as careful as possible so that the engine turns on at the required time. To do this, check the time mode and the set date.
Some security system functions can only work if properly synchronized. To carry it out, you need to turn on the mode (AM or PM) corresponding to the current time.

Setting the time on the Sherkhan 9 alarm remote control

Follow the procedure exactly and you can easily set the clock of the Scher Khan 9, 13, 14 anti-theft system.

To set the time, enter programming mode. Hold I and III. Press duration is two seconds. Picture on the keychain. Pro9 will appear on the screen and a remote beep will sound.
Switching to the time setting occurs automatically. The picture on the keychain depicting the dial will begin to blink.
Use the I key to set the hours.
II Set the minutes.
Press I and III for two seconds, the regulation will exit.

Setting autostart time

Owners of the Magikar 5 anti-theft system can program time intervals for engine auto-start (after 2, 4 and 8 hours) using a timer. To do this, follow these steps.

By simultaneously pressing keys 1 and 2, enter programming mode.
If the timer is on, turn it off. To do this, briefly press keys 2 and 4. The inscription “r” should disappear from the display.
Briefly click on key 4 thirteen times. Each press is confirmed by a single sound of the siren signal.
Select the desired engine autostart mode. Key 2 - after 8 hours, 3 - after 4 hours, 4 - after two hours.
Turn on the timer by pressing keys 2 and 4 simultaneously.

You can program the warm-up of the car engine at fixed time intervals: 5, 15, 25 and 45 minutes. Press buttons 1 and 2 to enter the menu and do the following.

Press button 4 twelve times. Twelve siren beeps should sound.
Select the desired engine operating time by activating the following buttons: 1 key - 5 minutes, 2 - 15 minutes, 3 - 25 minutes, 4 - 45 minutes.
Pressing keys 1 and 2 simultaneously will exit the programming mode.

Find out how to change the battery in the Sherkhan key fob.

How to set autorun time

Correctly setting the Sherkhan 5 Magikar time allows you to enable the useful engine autostart function. It will be in demand in winter, when you need to warm up the engine for a long time. Thanks to it, you can complete all the preparatory steps in advance and start moving at any convenient time.

To set autorun, enter programming mode. To do this, press the combination of keys 1 and 2.
After this, activate the timer by clicking on buttons 2 and 4. If everything is done correctly, the Timer inscription will disappear from the display on the control panel.
At the next setting stage, press button 4 13 times. In this case, each click should be accompanied by a short sound signal.
In the menu that opens, select the desired engine autostart mode. If the vehicle owner does this using button 2, the engine will start working after 8 hours, 3 - 4 hours, 4 - 2 hours.
The set operating parameters of the signaling system are fixed by simultaneously pressing keys 2 and 4.
After this, the car engine is started and the selection of fixed time intervals (from 5 to 45 minutes) begins. To do this, press the combination of keys 1 and 2.
Then they click on 4 12 times and wait for the same number of beeps.
Enter the desired value (1 - 5 minutes, 2 - 15 minutes, 3 - 25 minutes, 4 - 45 minutes).
By pressing 1 and 2, autorun programming is completed.

Sherkhan Magikar 2

This instruction is universal and is suitable for Scher Khan 3, 5, 8 remote controls.

Turn on the key fob programming mode by pressing for two seconds. electric buttons II and III. Login will be confirmed by the Pro9 picture.
To go to setting the time, press the I button once. The numbers should flash.
Key I changes the hours, and II changes the minutes.
Pressing 2 s of buttons II and III will exit programming.

It happens that the remote control stops working: it opens and closes the doors, but there are no symbols on the display. The key fob only shows the time. What to do in such a situation? Reboot the car alarm and re-register the remote control into the system memory.

Autorun programming

The Scher-Khan Magicar V alarm allows you to automatically start the engine in various modes:

Starting the engine every 24 hours allows you to start the engine at the same time every day, which is convenient, for example, for warming up in the morning. Starting every 2 hours allows you to maintain the temperature of the engine and interior on cold days or, conversely, cool the interior in the summer season. Both timer modes cannot be used simultaneously. The autorun mode is selected through the programmable functions menu.

To program autostart every 2 hours, you need to briefly press buttons II and IV. In this case, the engine will automatically start 2 hours after pressing. In this case, setting the time is not required.

To automatically start the engine every 24 hours, you must first set the exact time on the key fob, if it is not installed. (how to do this - see above). Setting up automatic engine start is as follows:

you need to press buttons II and IV and turn off the r mark;
select the start time using keys I and II;
Press keys II and IV again and turn off the r mark.

When the engine starts automatically, the key fob display shows a countdown until the engine is turned off.

Alarm Settings

To change system settings, use any of the previously registered key fobs. The car must be disarmed and the ignition must be turned off.

The system has two separate settings menus. The first menu is entered by pressing and holding buttons 1+2, and the second menu is entered by pressing and holding buttons 1+4. After the sound signal, you need to select the function number by pressing button 4 and make a short pause, after which the machine will sound the number of the selected function with siren signals. Using buttons 1,2,3 and 4 you can then set the desired function value.

In menu 1 the following functions are associated with autorun operation:

12: engine warm-up time at auto start, 5, 15, 25 or 45 minutes for settings 1 to 4, respectively.
13: Timer start type. In value 1, the launch occurs every 24 hours according to the time specified on the key fob, in values 2,3 and 4 - every 8,4 or 2 hours from the moment of activation.
14: limit the number of auto-starts, maximum 5, 7, 16. When set to 4, the number of timer starts is not limited.
16: autostart reservation type. In option 1, ignition interception occurs every time the ignition is turned off, but with a noticeable pause, during which the engine may stall. Option 2 introduces an additional condition: the doors must be closed. If you do not need auto start reservation at a specific moment, just open the door first and then turn off the ignition. There is also a delay before the ignition is intercepted. Therefore, the only adequately working backup option on Magicar 5 is manual reservation (function value 3), when you need to press and hold button 2 of the key fob before turning off the ignition.
17: way to complete the algorithm. In option 1, the car will stall after closing the door without arming, in option 2 - similarly, but with automatic arming. In option 3, the engine will stall only after manual arming. This is the only method you should use.
20: limitation of periodic starts based on battery voltage. In option 1 it is not set, option 2 sets a threshold of 11.5 V - until the voltage drops below, the start will be blocked. If you select to run every 24 hours, the setting is ignored.
21: autostart temperature threshold. In option 1 it is not installed, in options 2-4 the temperature is set to -15, -25 and 60 degrees, respectively (the last option is for operating the air conditioner in the heat).

In menu 2 autorun settings you need:

12: minimum starter rotation time, 0.6, 0.8, 1.2 or 2 seconds. It should be set to the possible minimum, since there is no automatic starter cut-off, as with alarms with a tachometer input.
13: maximum starter rotation time, 2, 4, 8, 10 sec. It should also be as low as possible in order to preserve the life of the starter and flywheel ring gear.
14: increase in starter rotation time during subsequent starting attempts after an unsuccessful one. In option 1, each new start attempt lasts 0.2 s longer than the previous one, in option 2 – by 0.4 s. Option 3 sets the fixed scroll time set by function 12.
15: pause between turning on the ignition and attempting to start, 2, 4, 8 and 10 seconds. The first two options are relevant for gasoline engines, options 3 and 4 – for diesel engines with glow plugs.
16: pause after stopping the engine until the ignition is turned off. 0, 4, 15 seconds or 4 with restart attempts.

The remaining autorun settings are related to the connection diagram to a specific car and should not be changed by the user.

Sherkhan Logicar 4

You can set the time on the remote alarm control key fob yourself by following these steps.

Press and hold the second and third buttons of the remote control for 2 seconds until the Pro9 picture lights up.
Click the first key once. The key fob will go to the time setting menu. The numbers will flash on the display.
Use the first key to adjust the clock. Button 2 - for setting minutes.
Once installation is complete, hold down the second and third keys for two seconds. There will be an exit from regulation.

How to set the time on the Sherkhan Magikar 7 keychain

In this article, auto electrician Alexey Molotov answers the question “How to set the time on the Sherkhan Magikar 7 key fob?”

Sometimes the time readings of the Scher Khan car alarm models Universe, Magicar, Logicar go astray. This happens for the following reasons.

weak power supply. During operation, the battery gradually discharges, losing its capacity. The clock readings are off;
recent battery change, after which the time is automatically reset;
poor contact contact. Inspect the working connections, if necessary, bend them;
manufacturing defects;
short circuit caused by the remote control getting into water or other liquid.

You can set the clock on the anti-theft system key fob yourself by following simple instructions.

Autostart based on temperature and voltage

Since Sherkhan Magikar 5 (in the generally accepted sense) does not allow automatic temperature triggering, only periodic triggering can be limited. In other words, the car will try to start every 2, 4, 8 hours if certain conditions are met:

the temperature at the installation point of the central unit is below the set threshold;
Battery voltage is below the set threshold.

You can set one or two of these conditions at the same time. Their programming is described below.

How to set the turbo operating period

An engine with a turbine has many features that affect its operation. Such a device must not be stopped instantly after prolonged operation at high speeds. Because of this, the engine needs to idle for several minutes. This will help to quickly cool the turbine and avoid various negative consequences. For such purposes, the Scher-Khan Magicar 5 security system has a Turbo mode. By activating it, the car's engine will run for an additional 2 minutes after pressing the brake.

Program the Turbo mode in the following way:

The vehicle is placed at neutral speed.
Turn off the ignition. In this case, the engine must remain in working condition.
Get out of the car and close all the doors. As a result, the hazard warning lights will flash.
After this, the control panel sets the car to security.
Wait 2 minutes until the engine stops and the shock sensor starts working.
Then press button 2 for 2 seconds and complete the programming process.

To enable or disable Turbo mode, you must simultaneously press the combination of keys 3 and 4.

Why time gets lost and what to do

Sometimes during operation of the security system, settings failures occur. Because of them, not only various alarm parameters are violated, but also time indicators.

The main causes of failures and ways to fix the problem:

My battery is almost done. If the power supply is discharged, it is sufficient to replace it.
Switch failure. If it causes the system to malfunction, then experts recommend buying a new element. This is due to the fact that its repair is complex and expensive.
Errors during programming of the control panel. Incorrect parameter settings often lead to time settings failures, so it is best to re-bind the key fob to the security system. Otherwise, the hours and minutes will often get confused and cause a lot of inconvenience to the car owner.

Setting the time on the Scher-Khan Magicar 5 is a task that must be completed immediately after turning on the security system for the first time. If this is done correctly, you will be able to enjoy all the benefits of the device and activate various useful functions.

On the keychain Sherkhan Magikar 7

The instructions allow you to set the clock not only on the Magicar 7 key fob, but also on 11,12, 10 Mini.

Setting the current time begins with entering the remote control programming mode. This is done by pressing for two seconds. keys I and III. Confirmation of actions - the inscription Pro9 and a tone signal from the remote control.
After successful completion of the first step, an automatic switch to the time setting occurs. The dial should flash.
Button I changes the clock readings.
II changes the minutes.
Exit the regulation mode by pressing for 2 seconds. buttons I and III.

Sherkhan Magikar 2

This instruction is universal and is suitable for Scher Khan 3, 5, 8 remote controls.

Turn on the key fob programming mode by pressing for two seconds. electric buttons II and III. Login will be confirmed by the Pro9 picture.
To go to setting the time, press the I button once. The numbers should flash.
Key I changes the hours, and II changes the minutes.
Pressing 2 s of buttons II and III will exit programming.

It happens that the remote control stops working: it opens and closes the doors, but there are no symbols on the display. The key fob only shows the time. What to do in such a situation? Reboot the car alarm and re-register the remote control into the system memory.

Why doesn't autorun work and how to fix it?

The main reasons why the auto start of a car engine does not work, and measures to eliminate them:

The engine is running. In this case, when you try to use the autostart option, the car's lights will turn on once. It is necessary to turn off the engine and try to start again.
When the ignition is on, the doors and hood (trunk) are open, two, three and four light signals will be given, respectively. Before autostart, turn off the ignition and close the doors, hood or trunk.
If the engine start reservation procedure has not been carried out on vehicles with a manual transmission, the light will sound five times. In this case, it is necessary to make a reservation described in the instructions. The gear lever must be in neutral and the parking brake must be applied.
If the parking brake lever is not applied, the system will give six light signals. To fix the problem, you need to tighten the parking brake.
When the brake pedal is pressed, seven light signals are given. Before autostart, release the brake pedal.
If the reasons why the autostart stopped working are different, the warning light will blink eight times. For example, autostart may not work due to problems in the functioning of the engine, malfunctions in the ignition system (wiring, starter, other elements). Also among the possible causes is a failure of the fuel pump or a breakdown of the protective relay in its electrical circuit. In this case, you need to contact service centers for help, diagnose the faults and fix them.

Error 03 appears when the doors are open

Key fob programming

Programming the key fob consists of three steps:

Quickly turn the ignition on and off three times, after which the warning light should flash once.
Turn the ignition back on, leaving it in this state.
Pause for no more than 4 seconds and press buttons 1 on all transmitters you want to register (maximum three).

4 seconds after the last key press, the system automatically closes.

Restarting is one of the most effective measures to take if your Magikar 5 key fob is not working. Only after you have verified that there is no physical connection (i.e. the key fob could not be assigned) can you look for a problem in the system. or replace the key fob.