Throttle sensor VAZ 2110 signs of malfunction

People are often interested in what signs of a malfunctioning throttle sensor on a VAZ 2110 exist. Knowing all the signs of a malfunction is simply necessary. Indeed, often when this sensor breaks down, drivers cannot find the cause for a long time. All parts and assemblies whose malfunctions manifest themselves in a similar way are replaced. And only when nothing helps, they pay attention to the damper position sensor (DPS). And a lot of time and money was spent. If they had checked it right away, there would have been fewer problems with repairs.

There are several signs of a car breakdown, in which case this sensor should be checked first and, if necessary, repaired.

Diagnostics

Signs of a malfunctioning throttle sensor on the VAZ 2110 are not too different from other models. But there are some features that are worth paying attention to. The following signs may indicate a malfunction of the TPS:

Floating idle speed until the engine stops in neutral;
Jerks during acceleration, the car jerks and accelerates extremely difficult;
Check Engine
light is on .

These signs can usually indicate more than just problems with the throttle sensor. That's why drivers rush to check everything except TPS. Many people are also afraid of getting into electronic systems.

The ideal option is diagnostics using a special scanner. This allows you to recognize the cause of the phenomena without any problems. The error code can be 0122 or 0123. When the signal is low, the first code is issued, and when the signal is high, the second. Such computer readings indicate a clear problem with the sensor. Code 0122 may indicate problems with the wiring supplying the TPS.

Be sure to check all wiring for damage. If you don’t have a scanner at hand, then when checking all the elements, you should first check the throttle and its sensor.

Principle of operation

. To properly check the TPS, you need to know the features of its operation. This sensor is a potentiometer that transmits all information about the position of the throttle valve to the controller. It works as follows. By pressing the gas, you change the position of the damper, and the sensor reacts to this. There is a constant voltage at its outputs, which can vary.

The controller reads the readings from it and, based on this data, doses the fuel supply. If the TPS malfunctions, incorrect readings are given, and as a result, the fuel supply begins to be unstable. And you may notice malfunctions in the engine.

Location

. To check the device in detail, you need to find it. This is quite easy to do. In the VAZ 2110, the throttle sensor is located on the throttle pipe. It connects to the throttle shaft. This directly ensures the operation of the device. The sensor is secured with two screws.

Possible faults

The contact-type sensor is quite reliable, and according to the designers’ plans, it should last at least 50,000 km. This is ideal under average operating conditions. In practice, it often fails before reaching half of its intended lifespan. Like any mechanics, the controller is very demanding regarding various clearances, frequency and speed of movement of the slider. The situation is complicated by the difficulty of diagnosis. The main symptoms of a malfunction of the VAZ-2110 throttle sensor are very similar to damage to many other components of the car. However, symptoms of TSD damage may include the following:

deterioration of engine dynamic characteristics;
jerking during intense acceleration;
stopping the engine when changing gears;
“dips” when sharply pressing the gas pedal.

As already noted, the weak point of the TPS is the mechanical moving contact. The resistor slider, moving across the resistive layer, damages it. The thin coating simply rubs off, the contact deteriorates, making further operation of the car problematic. In addition, the moving contact itself may break. In this case, the engine almost does not respond to the gas pedal.

In any case, the TPS cannot be repaired, and there is no point in restoring it. The price of the sensor does not exceed 300 rubles. True, first of all, you need to make sure that it is he who is faulty.

The main signs of failure of the TPS

If the device is faulty, then error p0120, which was mentioned above, may appear, as well as other errors indicating that there are deviations in the operation of the sensor: P2135, P0222, P0122, P0223, P0123, P0220, P01578. The errors themselves are not displayed on the dashboard, only the “Check Engine” light comes on, they can be seen on diagnostic scanners, mobile devices or a laptop (more on this later).

As for error P2135, it is typical for modern cars with electronic remote control position control. Its full name is “Mismatch of readings from sensors No. 1 and No. 2 of the throttle position.” Occurs when there is increased resistance in the circuit of one of the wires (there are four of them). About its reasons in the next section.

Other signs of TPS malfunction:

Floating speed, at idle the car shakes violently or stalls. A sharp jump in rpm up to 2000 - 3000.
The dynamics of the car drops, especially during acceleration (dips, jerks), towing, climbing a mountain, transporting goods; as people say, the engine does not pull. This also happens due to the unstable operation of the automatic transmission, everything is interconnected. Or, conversely, when you press the gas pedal slightly, the car accelerates sharply.
Increased fuel consumption - appears immediately after the sensor malfunctions.
When shifting to a higher or lower gear, including neutral, the engine stalls.
The machine switches to emergency mode, the crankshaft rotation speed does not exceed 1500 rpm, since the damper in this mode is only slightly open by 6-7%.

The same signs indicate a malfunction of the throttle valve, the condition of which is important to periodically check and, if necessary, clean.

Causes of malfunction of contact sensors

The main reason for failure is wear of the resistive tracks, leading to a complete or partial break in the electrical circuit. This leads to the transmission of incorrect data to the ECU.

Causes of malfunction of contact sensors:

Wear of the resistor layer leads to loss of electrical contact. This can happen either at the beginning of the slider’s movement (typically when the voltage at the sensor output is low), or on another section of the tracks.
Broken or worn tip.
Wear of drive gears.
Short circuit of signal or electrical circuits.
Broken wiring, especially for VAZ cars, whose wires are not reliable.
Oxidation of contacts and contamination of connectors.

Most causes can be diagnosed visually after disassembling the device and using a multimeter.

Regarding error P2135, which was mentioned in the previous section, its causes:

poor ECU contact ground;
oxidation of contacts in the connector;
main relay malfunction;
short circuit and other reasons.

Problems with the VAZ 2110 throttle sensor and their diagnosis

As you know, eternal parts for cars have not yet been invented. And the breakdown of the TPS can be foreseen; for this you need to inquire about the possible reasons for the failure of this part. Here are the main ones:

Abrasion of the sprayed base layer, which serves to move the slider (the result is incorrect TPS readings).
Failure of the movable type core (the result is deterioration of the contacts between the slider and the resistive layer).

How can you figure out problems with this sensor yourself? To do this, you can independently diagnose the operation of your diagnostics:

Listen to the VAZ-2110 engine idling:
Quickly release the gas pedal:
Pick up speed:

Experts say that most often the sensor fails when the resistive track is heavily contaminated or is completely broken. To verify the opposite, you need to check the working condition of the TPS.

Test with a multimeter (preferred method)

Check procedure:

Turn on the ignition.
Check if power is supplied to the sensor. To do this, disconnect the chip and measure the voltage readings on the wires suitable for the sensor. To do this, set the switch on the device to the “20V” position and take the readings (the norm is 4.5-5.5V). If there is no voltage, then we look for an open circuit or another reason.
We check the presence of signal voltage coming from the sensor to the computer when the damper is fully closed and open. To do this, set the “-” of the multimeter to ground (engine block or battery), and connect the “+” to the third signal contact. When the throttle is closed (the gas pedal is depressed), the voltage should not exceed 0.6-0.7V. When fully open (the accelerator is fully depressed) - at least 4V.
Read also: Do you know how to change the low beam lamp on a Renault Duster
Next, we check for the presence of surge voltage when moving the damper between the “closed” and “fully open” positions. To do this, use an additional wire, which you insert into the Pin of the wire going to the ECU, and connect the other end to the plus of the device. Place the contactor back on the sensor. Gradually press the gas pedal or pull the cable and monitor the instrument readings. The voltage should increase and decrease smoothly. If jumps in U occur, this means that the resistor tracks have worn out in some places and the TPS must be replaced.

POPULAR WITH READERS: What is a contract engine, you need to know this

You can also check the sensor by measuring its resistance. For this, a multimeter switched to the appropriate mode is also used. Readings are taken between the negative and signal contacts. For ease of work, the product can be removed.

Standard readings for VAZ models:

The damper is closed – 1.5 kOhm.
Open – 7.5 kOhm.

For example, the Niva Chevrolet has different regulatory indications:

The damper is closed – 2.4 kOhm.
Open – 8.2 kOhm.

Therefore, see the operating and repair manual for your car model for voltage and resistance data.

The process of changing resistance should also occur smoothly without jumps. To do this, rotate the sensor mount.

Checking the VAZ 2110 throttle sensor with a diagnostic tool

The words “diagnostic tool” sound loud, but in fact, it will be enough to purchase an ELM327 auto scanner or Scan Tool Pro running on the same chip and install special software, for example, OpenDiag, on a smartphone (Android) or iPhone (iOS).

You can also carry out a complete diagnostic of the car via a laptop. Or use the AVTOAS-F16 CAN multi-system scanner.

But in short, the essence of using scanners is to connect to the computer and, using special software, see the error numbers registered in it.

Connection is possible via: USB cable, WI-FI, Bluetooth. But it is important to know that some ECUs, especially on older cars, do not support WI-FI and Bluetooth protocols and the ELM327 scanner can only be connected to them via USB with a USB to MicroUSB Adapter. Accordingly, you need to purchase a wired scanner model.

It is better to use scanners with a 32-bit chip; they provide more opportunities for diagnosing a car.

Possible errors associated with the TPS and the electrical circuit were mentioned above, but other errors associated with unstable operation of the engine and electronic systems of the car may also be registered in the ECU. Some of them can be reset, for example, “motor overheating”.

The advantage of using a scanner is monitoring the operation of the sensor in real time. To do this, turn the throttle while squeezing the gas pedal. The program will display changes in voltage and inclination angle. Sudden voltage surges will indicate a problem.

Evidence of pollution

Let's look at the signs that indicate a malfunctioning throttle valve:

Revolutions. You sharply release the gas pedal, but the engine is in no hurry to switch to idle speeds from high speeds. Instead of a smooth reset and acceleration, the engine begins to shake, it either stalls completely, or with great difficulty restores the required speed;
Launch. Your VAZ has difficulty starting cold, and sometimes you cannot quickly start even a hot engine. There may be other reasons for this phenomenon, but the fact that the throttle valve is to blame may be indicated by the fact that after several throttle applications (short-term presses on the gas), the engine usually starts;
The starter spins for a long time before starting, and the smell of gasoline is heard from the exhaust pipe;
The engine may run for a couple of minutes after starting.

Dirty throttle valve VAZ 2110

How to understand that the cause of the problem is the throttle sensor of the VAZ 2110

So:

This device is designed to read information about its position from the gas pedal, as well as determine at what angle the throttle valve is open.
It is located on the same axis as the damper drive, on the throttle pipe. Its service life cannot be predicted; many factors can influence device malfunctions.
One of the most common malfunctions is increased idle speed. This happens because in the event of a breakdown, the TPS mistakenly determines the position of the damper, and its functions are transferred to another controller - the mass air flow sensor (the sensor responsible for the mass air flow).
The problem can manifest itself in different ways. For example: the car stalls while driving or, when accelerating and picking up speed, you feel jerking. Sometimes the “XX” (idle) speed is unstable, no matter what engine operating mode you turn on. The CHECK ENGINE indicator may light up, although this does not always happen.
It is not difficult to check the operation of the sensor: with the ignition on, you need to measure the voltage between its winding and ground with a voltmeter. In this case, the voltmeter reading should not exceed 0.7 volts.
Then you need to turn the plastic sector by hand, thereby opening the throttle valve. The new measurement should show a voltage value of 4 volts, or slightly more.
Now you need to turn off the ignition and measure the resistance. Having opened the connector, connect an ohmmeter between it and the slider terminal. Smoothly turning the sector, monitor the readings of the ohmmeter needle - there should be no sharp jumps.
In case of any deviations from the norm, the VAZ 2114 throttle position sensor will need to be replaced. Moreover, if the tip is broken, or the coating of the base along the slider is worn off. For all injection VAZ cars, starting from 2108, the sensor itself and the work to replace it are identical.

Examination

In addition to checking the sensor itself, pay attention to the condition of the throttle valve. Sometimes it becomes coked, and as a result its mobility is lost. In this case, symptoms similar to sensor failure will also be observed.

The simplest check of the sensor’s functionality can be done even without removing it from the car:

To do this, turn on the ignition and measure the voltage at the TPS terminals, it should not exceed 0.7 V;
Next, use the plastic sector to fully open the throttle. Then the voltage is measured again. The normal value is at least 4B;
Then check the correct operation of the sensor. To do this, you need to measure the voltage at the TPS terminals when the damper moves.
It should not jump sharply, all changes should occur smoothly. Abrupt changes indicate a malfunction of the device;
The final check is to check the resistance between any of the terminals and the slider contact. To do this, turn off the ignition and pull out the connector. When turning the damper, this indicator should change evenly.

If you find out that the sensor is faulty, you should replace it. It is important to choose this design element correctly. The VAZ 2110 is equipped with 2 types of TPS. One of them is film resistive. This type is installed by the manufacturer, the sensor is designed for 55,000 kilometers. The other type is called non-contact. It uses a Hall sensor. This device has no restrictions on its service life. But it costs a little more.

Conclusion

. The “ten” is equipped with a familiar sensor. The same version of the device is installed on this entire family. In this regard, all signs of a malfunction of the throttle sensor on the VAZ 2110, with the exception of minor nuances, are similar on all cars with this sensor model. Timely repairs will save you from the hassle of having a poorly functioning machine.

The throttle unit (DU) is responsible for supplying air to the engine of the VAZ 2110 car. The enrichment of the fuel mixture with fresh air depends on its operation. And if the throttle assembly is damaged, then the functioning of the power plant is disrupted. If it breaks down, the remote control is replaced with a new one, but sometimes the result of a malfunction can be contamination of the unit or a broken TPS - throttle position sensor of the VAZ 2110. You can do both cleaning and replacement yourself.

Helpful advice: cleaning and changing the gasket is necessary every 50-60 thousand kilometers. This figure is suitable for almost all VAZ models. Then repairs and replacements will not be required. Cleaning will cost only 150-200 rubles.

Location and main malfunctions of remote control and TPS

To clean or replace, we need to find the throttle assembly. In a VAZ 2110 car it is located in the engine compartment on the throttle pipe. A malfunction of the damper can be determined by the following signs:

There are noticeable jerks when accelerating.
Increasing idle speed.
"Check Engine" indication.
At neutral speed the engine stalls.
Decrease in dynamics.
"Floating" speed.

Removing the throttle assembly

Dismantling the remote control will be necessary in any case. If there are malfunctions, the unit is replaced with a new one, but if there are no problems other than contamination, then the gasket on the damper is changed, and then a thorough cleaning is performed. For dismantling you will need a set of screwdrivers and a 13mm socket wrench. You also need to purchase a special cleaning fluid, which can be found at any car store. An excellent option would be a product for carburetors - Arbo. Dismantling is carried out only on a “cold” motor.

Cleaning

So, the part has been removed. Now you need to assess the condition of the gasket. If cleaning is being done for the first time, the gasket should be replaced. Cleaning is carried out using a pre-prepared product, cotton swabs and a toothbrush. We need to clean all cavities and hidden channels. The damper itself and the landing sites need to be given special attention.

As a result, the remote control must be completely cleaned of grease and dust. Before installation, it is worth cleaning the crankcase ventilation duct. Here you will need a foot pump. It is better to perform purging with the same product.

Troubleshooting throttle position sensor

The cause of the defects described above may be a faulty VAZ 2110 TPS. This element is necessary to inform the controller about the position of the damper immediately after the gas pedal changes its position. The voltage at the TPS output is constantly changing - this allows for the correct supply and dosage of the fuel mixture.

If the TPS malfunctions, malfunctions begin, as information about the throttle position is supplied incorrectly. Because of this, excessive fuel consumption or interruptions in the operation of the power plant may occur. Sometimes cleaning the surface of the sensor itself solves the problem. But if the TPS is damaged, then only replacement will help. The replacement process is very simple. It is necessary to remove the old sensor and install a new one in its place. No additional work is required.

Replacing the sensor

Like any other vehicle electronics component, the throttle sensor is changed when the negative terminal of the battery is reset. A Phillips head screwdriver is sufficient for removal. Disconnect the connector and unscrew the fastening screws.

We remove the sensor and clean the docking area with a dry cloth. If necessary, apply a little grease to the throttle axis. Then we install a new sensor, put on the connector and connect the battery.

Important! After replacing the sensor, you need to start the engine and let it idle for a while.

After this, gradually add speed several times without moving the car. The electronic control unit (ECU) must adapt to the new sensor. Then we operate the machine as normal.

What is TPS in a VAZ-2110 car?

The throttle position sensor is abbreviated as TPS among motorists. This part is used in several types of engines:

Gasoline injection type.
Single injection type.
Diesel engines.

TPS is also known as a throttle valve potentiometer. This is due to the fact that the sensor is designed to function as a variable resistor. The sensor itself is installed in the engine compartment - the place of fixation is the throttle pipe. The mechanism of operation of the sensor is as follows: depending on the position and degree of opening of the throttle valve, the resistance also changes. That is, the level of the value of such resistance depends on the pressing of the gas pedal. If the pedal is not pressed, the throttle valve will be closed and the resistance will be minimal. The opposite is true when the damper is open. Accordingly, the voltage across the TPS, which is directly proportional to the resistance, will also change.

The control of such changes is carried out by the electronic control system; it is the one that receives all signals from the TPS and supplies fuel using the fuel system.

So, at the maximum voltage of the signal contact of the throttle position sensor, the fuel system of the VAZ-2110 car will supply the largest portion of fuel.

Thus, the more accurate the TPS indicators, the better the VAZ-2110 electronic system adjusts the engine to the correct operating mode.

Device

1 - Shaft;
2 - Housing; 3 - Connector; 4 - Contacts; 5 - Resistor; 6 - Ring; 7 — Spring stopper; 8 - Spring; 9 - Cover; This component of the system is a fairly simple electrical resistor, which changes the resistance when the axis is rotated.

The sensor is located on the damper shaft and, when it opens, performs the function of turning together with the damper. Due to the fact that the design is quite primitive and unreliable, the sensor often fails, resulting in certain problems with the formation of the fuel mixture. So, in most cases, the problem is the rubbing of the tracks, but the possibility of other problems with the condition of the resistor cannot be ruled out.

Communication of the throttle valve with other automotive systems of the VAZ-2110

The throttle valve of a VAZ-2110 car is a component of the engine intake system and is directly connected to a large number of other vehicle systems. These include the following systems:

directional stability;
anti-blocking;
anti-slip;
anti-slip;
cruise control.

In addition, there are those systems that are controlled by the electronics of the gearbox. After all, it is this throttle valve that regulates the flow of air into the car system and is responsible for the quality composition of the fuel-air mixture.

TPS design

The throttle position sensor can be of two types:

In its design, it resembles an air valve - in the open position the pressure corresponds to atmospheric pressure, in the closed position it drops to a vacuum state. The TPS includes DC and AC resistors (each resistance is 8 ohms). The process of opening and closing the damper is monitored by the controller, with subsequent adjustment of the fuel supply.

If at least one symptom of a malfunction occurs in the functioning system of this sensor, then fuel may be supplied to the engine either in excess or in deficiency. Such malfunctions in engine operation are reflected in the engine of the VAZ-2110 car and on its gearbox.

Why is it needed?

The throttle position sensor is responsible for determining the current throttle position. Depending on this, the fuel supply system changes the amount of fuel supplied under one or another operating mode of the power unit.

If problems arise with it, you can contact a service station so as not to waste your energy and nerves. But in practice, changing the TPS yourself is quite simple, plus you will save a decent amount of money.

The desired regulator is located on the side of the throttle pipe on the throttle valve axis.

Regulator location

Features of work

The TPS is essentially a variable resistor, one output of which is supplied with 5 Volt power. The second contact is connected to ground, and the third is connected to the controller.

When you press the gas pedal, the voltage changes. The sensor monitors the output voltage on the controller, thereby regulating and monitoring the quality of the supplied air-fuel mixture. This directly depends on the opening angle of the damper itself.

If for some reason this regulator fails, a catastrophe will not occur, since another sensor, the mass air flow sensor, will temporarily take over its functions.

This does not mean at all that the TPS can not be changed. Each regulator has its own functions, so there is no point in transferring the tasks of the TPS to the MAF.

Characteristic symptoms of a malfunctioning TPS condition

Thanks to the correct functioning of the throttle position sensor, the fuel system of the VAZ-2110 car engine works with a smoothing effect. That is, the vehicle moves smoothly, and the gas pedal responds well to pressure. Therefore, a malfunction of the TPS can be noticed almost immediately by the following signs:

Poor engine starting.
Noticeable increase in fuel consumption.
The car's movements are intermittent.
The idle speed of the engine is noticeable when running.
The Check e light comes on on the dashboard
The car accelerates poorly due to delays in acceleration.
Popping sounds are heard in the intake manifold.

Of course, these signs of a faulty sensor may not all be observed at once. But even if you notice only one of the above symptoms, it is worth carrying out computer diagnostics of the vehicle at a service center.

Location and principle of operation of the element

All cars of the “tenth” family with an injector, including the latest VAZ 2115 models, are equipped with a variety of sensors. They are located at various points and are busy measuring various parameters, transmitting data in the form of electrical impulses to the processor that controls the operation of the engine. The location of the meters depends on their purpose, so the VAZ 2110 throttle position sensor is not difficult to find; it is located in the same block as it. The same element is installed in the Lada Priora car.

Checking the operation of the throttle position sensor

To check the TPS yourself, it is not necessary to call an auto electrician for consultation. To do this you need a multimeter or voltmeter. Next, experts offer step-by-step instructions for checking the sensor.

The first step is to turn the key in the ignition switch, take the voltage readings between the sensor slider contact and the minus. In normal condition, the indicator will be up to 0.7 V.

The second step is to turn the plastic sector and open the damper, and then take measurements again. In the normal state of the sensor, the device will show a result of 4 V.

The third step is to turn on the ignition completely (as a result of this the connector will stretch out), measure the resistance between the slider and any terminal. When rotating the sector, you must monitor the measuring device:

when the multimeter or voltmeter needle moves smoothly, the sensor is working;
when the needle on the meter shows sudden changes, the DPPZ is faulty.

Once the sensor is faulty, it can be adjusted or replaced. The VAZ-2110 car repair service center will tell you how to do the right thing.

As you know, the VAZ 2110 was produced with injection and carburetor engines. The injectors are equipped with an impressive number of sensors, the performance of which determines the functionality of important units. Therefore, if they break down, problems may arise in moving, power decreases, fuel consumption increases, and much more.

A prime example of an important sensor is the throttle position sensor. Today we’ll talk about it in more detail.

The desired regulator is located on the side of the throttle pipe on the throttle valve axis.

Regulator location

Features of work

The TPS is essentially a variable resistor, one output of which is supplied with 5 Volt power. The second contact is connected to ground, and the third is connected to the controller.

If for some reason this regulator fails, a catastrophe will not occur, since another sensor, the mass air flow sensor, will temporarily take over its functions.

This does not mean at all that the TPS can not be changed. Each regulator has its own functions, so there is no point in transferring the tasks of the TPS to the MAF.

There are several telltale signs of trouble that may indicate that there is a problem with the throttle valve control.

High idle speed;
When the gear is switched off, the engine may stall;
When the car picks up speed, the car jerks and jerks are felt;
Acceleration dynamics deteriorate significantly;
Floating speed occurs at idle.

It should be noted that similar symptoms may also be characteristic of the failure of other components - the idle speed control or the ignition module, for example. Therefore, you first need to check the TPS.

Checking the status of the regulator

Next, let's talk about how you can check this throttle valve sensor. The event is necessary because it allows you to understand whether all the troubles are really due to it, or whether the problems arose due to the failure of other elements of your car.

It’s not uncommon for novice car owners to make hasty conclusions based on the primary signs of a breakdown. This results in unnecessary repair work and costs.

To check the current status of the throttle position sensor you need to:

Measure the voltage at the output of the slider, turning on the ignition and opening the idle contacts;
If the test shows that the voltage is more than 0.7 volts, then the sensor has indeed failed;
Open the damper completely. In normal condition, voltage readings should be no more than 4 volts;
Measure the variable resistor for resistance;
To do this, connect an ohmmeter or a multimeter in ohmmeter mode to the power supply and output;
Slowly begin to turn the throttle;
At the same time, monitor the readings on the device;
If, as the damper opens, the resistance also changes slowly, then the unit is working properly.

If you find during the test that the sensor is faulty, you only need to replace it. It cannot be repaired.

The resistive layer along which the slider moves wears off over time due to friction. Because of this, the regulator begins to produce incorrect data, the characteristics of the supplied mixture change, and engine performance deteriorates.

Disabling the regulator

In fact, changing this sensor is insanely easy. So don't rush to send your car to a service station. Everything can be done with your own hands, the quality will not suffer from this.

To remove the throttle position sensor, you first need to find it.
As we have already noted, the desired unit is located on the side of the throttle pipe on the throttle valve axis.
Having found the element, pick up a shaped screwdriver.
Using this simple tool, unscrew a couple of bolts that hold the device.
Pay special attention to the gasket that is available under the old regulator. We do not recommend using it again; it is better to immediately buy a new one. Often the gasket is already included with the throttle sensor itself.
After removing the old sensor, you can slightly clean the place where it is installed if there is dirt there.
Next, a new sensor is installed along with a new foam gasket and the bolts are tightened.
Try to tighten the fasteners as far as possible, otherwise the new throttle sensor will quickly lose its effectiveness. The work will have to be done again.
There is no need to make any adjustments after replacement.
The zero mark on the controller will determine that the throttle is completely closed.

Mechanism of action of the equipment

The TPS works like a potentiometer.

Each output of the mechanism has its own channel - a 5V electrical signal goes to one contact, the other is connected to ground, the third is connected to the controller. When the gate is turned, the voltage from the current collector slider to a specific output changes.
With the ignition on, you can check it with a special device by installing probes on the input contacts of the unit. When the throttle shield is closed, the readings will be in the range of 0.5 - 0.7 V. When open - up to 4V.
The VAZ 2114 throttle valve is in contact with the idle air control mechanism. When the shutter is closed, the IAC comes into operation, and the engine is filled with additional air, bypassing the TPS.

You can check the performance of the valve sensor by measuring the resistance - with an ohmmeter. If the mechanism is working properly, the indicators should be zero.