Ignition module grant 8 valves connection pinout

Contact ignition system VAZ 2107

The classic contact system used on the VAZ consists of 6 components:

• Ignition switch.
• Breaker-distributor.
• Spark plug.
• Low voltage wires.
• Ignition coil.
• High voltage wires.

The ignition switch combines two parts: a lock with an anti-theft device and a contact part. The switch is secured with two screws to the left of the steering column.

The ignition coil is a step-up transformer that converts low voltage current into the high voltage needed to produce a spark in the spark plugs. The primary and secondary windings of the coil are placed in a housing and filled with transformer oil, which ensures their cooling during operation.

The ignition distributor is the most complex element of the system, consisting of many parts. The function of the distributor is to convert constant low voltage into high pulsed voltage with the distribution of pulses across the spark plugs. The design of the distributor includes a chopper, centrifugal and vacuum ignition timing regulators, a movable plate, a cover, a housing and other parts.

Spark plugs ignite the gasoline-air mixture in the engine cylinders using spark discharges. During operation of the cross sections, it is necessary to monitor the gap between the electrodes and the serviceability of the insulators.

More about the device

Many electrical devices are based on the use of the law of self-induction. The notorious ignition coil consists of the following elements:

• The outer layer, also known as the primary winding, is made of thick copper wire with a diameter of 0.8 millimeters. Number of turns: 250-400 pieces;
• The inner layer, also known as the secondary winding, is made of thin copper wire with a diameter of 0.1 mm. Number of turns: 19-25 thousand pieces;
• The core is made of special transformer steel, which is an excellent affordable ferromagnet.

Also, switching devices are separately distinguished, that is, high and low voltage terminals. The second ones are connected to the battery and the metal part of the car, almost always the frame.

New ignition module

Checking the battery with a multimeter
They are attached completely differently. Therefore, the new one, unlike the old one, is held on by one bolt, and not by three. I secured the controllers to a corner, which I attached under the air filter mounting bolt.

The letter designations are clearly visible on the device body. Because it is in it that a high-voltage pulse is generated, and there, in most cases, a break or rupture of the turns can occur.

It happens because of the following: The car was operating when the high-voltage wires were not working - approx.

And also the cause of the malfunction may be a soldering failure; this usually happens due to frequent vibration. Or moisture formed during washing or condensation. Testing with the engine running is done as follows.

The first contact of the tester is in socket D, the second is to ground. The multimeter switch position is 20 volts. If there is power, the tester shows 12 volts. The first contact is in socket C, the second is ground.

Switch on 20 Ohm ohmmeter. Normally it shows less than 1 ohm, that is, the mass is normal. The first contact is in socket B, the second is ground.

20 volt switch. The norm is not less than 0.3 volts. If this is the case, it means that a normal pulse is coming from the Hall sensor to position B. Contact A is checked in the same way as the previous one.

Chevrolet Niva ignition coil

If such a check shows the norm, you need to test the module. The old spark plugs are black with soot, but there is nothing criminal in appearance. We install new ones, pray and start them. Vzhiiiihh - it started, it doesn’t bother. I warmed up the engine a little, I try to drive - everything is cool, I’m on my way. I fly home quickly, joyful, it’s already 8 pm.

I think to myself - lucky that there are candles. It happens - it breaks through.

The next day in the morning I take my wife to work for 15 minutes there, I drive back and almost approach the house, I feel that the traction has disappeared, I press on the gas and the car slows down. A couple of seconds later the engine started up.

Damn, I think it’s good that I got there on my own. Google says - change the high-voltage wires, they also break through and in theory they should also be changed more often, and not ride on the same wires for years.

BB wires I take the bus and go to the nearest spare parts store. The choice is not great, there are no branded and cool Teslas and the like. This is especially true when operating in difficult conditions, when the engine operates at high speeds, while the travel speed is low and, as a result, the interior ventilation is insufficient.

On the Niva Chevrolet, the spark plugs are closely related to the previous device. And if they malfunction, all the same problems as described above are possible. Spark plugs fail especially often in winter. This is due to the fact that the car is not used so often and mainly for short trips. Due to the low ambient temperature, the candles do not warm up to the maximum temperature at which they self-clean from carbon deposits.

If problems occur, it is necessary to replace the spark plugs in a timely manner so that this does not affect the performance of other system components. Spark plugs for the Chevrolet Niva must be purchased specially for eight-valve injection engines.

Loading ..

When purchasing, you should pay attention to the gap between the electrodes. It should be no more than 1.5 mm

If this distance is greater, this will affect the duration of the candle.

Remove the engine screen. We remove the tips of the high-voltage wires from the ignition coil terminals. Having released the lock of the engine control system wiring harness block... ...disconnect the block from the coil connector. Using a 5mm hexagon, unscrew the four screws securing the coil to the bracket... ...and remove the coil. Install the ignition coil in reverse order. For the correct connection of the tips of high-voltage wires... ...the cylinder numbers are marked on the coil body next to its terminals.

Modules and ignition coils Lada Niva 4x4

Checking the generator with a multimeter

This group of products includes modules and ignition coils for Lada Niva 4x4 cars (VAZ 2121, 2131).

The ignition module is an element that is designed to receive current and transmit it through high-voltage wires to the spark plugs. The modules come in two types: 2112-3705010 and 2111-3705010, but they are not interchangeable, as they are installed on different ignition systems. There are also separate ignition coils, one for each cylinder, installed on the spark plug without high-voltage wires 2112-3706010.

The ignition coil is needed to produce an ignition spark and ignite the fuel-air mixture.

• 2112-3705010 on cars with eight and sixteen valves with an engine capacity of 1.5;
• 2111-3705010 on eight-valve cars with an engine capacity of 1.6;
• 2112-3706010 on cars with sixteen valves with a volume of 1.4, 1.6.

What are the signs of a faulty ignition module?

• traction failures during acceleration;
• “check engine” lights up on the instrument cluster;
• uneven engine operation at idle speed; “floating”;
• the engine “troubles”, one of the pairs of cylinders does not work (you can hear it).

But unlike the module, if the coil malfunctions, the controller may also fail.

Let's figure out replacement time

Problems with the ignition coil largely duplicate those with spark plugs. Namely:

• Gasoline consumption has increased;
• The engine refuses to work;
• Power has dropped;
• Exhaust gases have become more “dirty”;
• The engine began to “trouble”;
• Suspicious vibration of the unit appeared;
• It became difficult to start.

At the same time, as we wrote above, the life of the coils can decrease for a number of reasons : ingress of water, oil vapors and auto chemicals, overheating. Any coils instantly fail due to insulation breakdown. And the spark plugs themselves can put a lot of stress on them, causing the coil to burn out. Particularly vulnerable are individual systems that operate at extreme temperatures and require additional protection.

Candle making options:

Checking the DPD with a VAZ 2110 multimeter

To increase productivity when creating these products, some technological features are used, which in theory can increase productivity, and as a result, the highest quality fuel combustion:

1. Platinum coating. Allows you to increase the service life up to 50 thousand kilometers due to the fact that the surface becomes more resistant to the combustion products of the fuel mixture.

1. Multi-contact spark plugs. Typically used in cars that are operated in regions with predominantly low temperatures. Such products make it possible to improve the starting of a cold car in the morning. In summer, it is recommended to replace them with regular ones.

The principle of operation of the ignition module on a Chevrolet Niva

Ignition modules are structures equipped with both secondary and primary windings. Additionally, there is a commutator, inside which the current switches from one coil to another. The work is carried out from the computer or vehicle control unit. Analysis and collection of information is also performed using the specified blocks. This check gives an accurate result.

The ignition module has four sockets for connecting high-voltage wires. They then move on to the spark plugs.

Varieties

Over the entire period of production of these cars, manufacturers equipped them with two main groups of devices:

1. MZ from a VAZ 2112 car. Mounted until 2006. It is equipped with a system responsible for controlling the sparking system.
2. The module is from a VAZ 2111. It is controlled by signals from the ECU. In fact, this is an ordinary modern ignition coil.

The indicated modules are not classified as interchangeable parts. Their design is different, so it is impossible to replace one type with another. By appearance it is easy to determine which part is used in a particular case. The old Niva Chevrolet ignition module has increased dimensions and weight.

Module design

Converting low voltage signals to high voltage is the main purpose of any module. It is based on the process of spark formation inside the cylinders. The design of the module is similar to a pulse transformer. The signal from the electronic control unit is supplied to the input of the device. In this case, the voltage is removed from the output to 20-30 kW. This means that each wire works stably.

The module has a connector to connect the low-voltage part and four additional sockets. So-called armored wires are inserted into them.

High voltage is supplied to two cylinders at once. The formation of a spark takes up to 90% of the total energy of the device. The conductivity of the mixture is associated with high pressure, which is maintained on a constant basis. The module has only two independent coils.

Where is the ignition module located?

The part is fixed to the bottom of the cylinder block. For this reason, the ignition module is constantly exposed not only to corrosion, but also to high temperatures. The second factor for this system can be called the most critical. Therefore, owners often move the structure themselves to another place where the conditions are not so problematic.

Brand tour

A significant number of OEM reels are in fact produced by the companies that will be listed. This does not mean that there is no point in taking the original. Rather, you gain time by almost immediately selecting the spare part you need, installing it and getting back on the road.

Of the expensive goods, it is worth paying attention to those that are in boxes with the names of the following companies : Valeo (France), Beru (Germany), Magneti Marelli (Italy). The quality of the coils from these companies is very high, but the price, as they say, is steep.

Coils from these companies are very popular: Bosch (Germany), NGK (Japan), Tesla (Czech Republic).

A budget solution can be reels from the Czech company Profit, as well as the well-known Danish JP Group. They will have to be replaced more often than more expensive devices, but even in this case their purchase will be profitable.

Peculiarities

The operation of the Niva 21213 system depends on the condition of its parts. High-voltage wires must have a distributed resistance, the value of which is in a certain range. Too much resistance will result in the ignition coil not having enough power to cause a breakdown. Low resistance increases interference. Although, some install just such wires. Of course, the spark power will increase and engine performance will improve. Spark plugs can lose their properties over time. The electrodes melt and carbon deposits appear.

The high temperature inside the cylinders greatly heats the spark plugs. Therefore, even when the ignition is turned off, ignition occurs from heated spark plugs.

It is important that all spark plugs have the correct gap between the electrodes. This will ensure high-quality ignition of the mixture. The distributor cap must be clean from dirt, t

because its presence can lead to current leakage

The distributor cover must be clean from dirt, since its presence can lead to current leakage.

How to check the ignition module, ignition coil and armored wires?!

I change the wires, pray, start it - it starts. No problem, everything is fine. Since I saw oxides inside one old wire, I decided that now the problem was definitely solved. Tomorrow we are planning to go to my mother-in-law's, a kilometer away, so it was still a good idea, what if there were no wires? There is nothing to do, we are taking risks. We leave in the morning, we drove 20 kilometers, everything is fine, I am already relaxed, it’s good that we are still driving through populated areas.

Resistance between the high-voltage terminals of the KILLED ignition module.

In Vakhrushi - again, according to the classics - traction disappears, the car jerks. The likelihood of both breaking down is very high, I hope, of course, to get by with little damage and only change the sensor.

Meters behind me I saw a VAZ auto parts store, I walked there and warmed up. First I take the sensor, it costs rubles. I change things there a little, unscrew a couple of small bolts, pull out the connector and change the sensor. But, damn it, the bolts stuck, one was unscrewed, and the other began to roll, since you can’t really get to it, you need a screwdriver with a flexible shaft type. There is nothing to do - I stupidly broke off the sensor with pliers, only after that I managed to crawl up and unscrew the boiling bolt with pliers.

I change the engine control valve, start it up, and again it’s a dog. Ignition module All hope is that by changing the ignition module, the car will drive and we will still get to mother-in-law Shuruya back to the store and buy an ignition module from MZ, it is not cheap - it costs rubles, domestic. Changing it is quite easy, the MZ is attached to the engine with 3 bolts, and explosive wires go from it to the engine itself.

And also the cause of the malfunction may be a soldering failure; this usually happens due to frequent vibration. Or moisture formed during washing or condensation.

More details about breakdowns Armored wires are marked with arrows. The same high-voltage pulse that occurs on the secondary winding must be fully used, that is, if this does not happen when the integrity of the wire is violated - approx. The first signs of a malfunction As a rule, two coils do not fail at once, therefore, it will still be possible to start the engine even with a partially faulty module. But an experienced car owner should immediately suspect a problem, and it is accompanied by the following: Jerking may be observed while driving.

All of the above reasons can also be observed during other breakdowns, so it is necessary to diagnose it correctly, and for this you need to know how to check the ignition module with your own hands.

Niva Club - OFF-ROAD Wheels Nissan Skyline of the Year in Bishkek. Price: 3,$ & | Car sales in Kyrgyzstan - diabloarea.ru The interior smells of antifreeze Niva Chevrolet: where does the smell come from?

Reviews

How to check the ignition module on a Chevrolet Niva - check procedure

A multimeter will help you check the condition of the node. It is not necessary to use expensive instruments with high accuracy. The main thing is the presence of a digital display, then any measurements are simplified.

First you need to make sure that the wiring of the device remains intact. To do this, perform the following steps:

1. The switch on the rear panel of the device is set to the 200 Ohm position.
2. The connector is disconnected from the module and the high voltage wires are disposed of.
3. The voltage is measured sequentially between the middle and extreme contacts of the terminal blocks.
4. The device readings should be within 5 ohms. The heater, for example, works while maintaining other indicators.

The resistance of the secondary winding is checked in the next step. Here you need to move the switch to the 20 K position. The probes are connected to wires with the appropriate voltage. 5.4 Ohms is the standard reading for instruments in this situation. Otherwise, the connection cannot be properly organized.

How module malfunctions are shown by diagnostics

By visiting a service station or using amateur diagnostic equipment (error scanner, a special application and an adapter for computer diagnostics via Bluetooth), you can also find out that the “root of evil” is in the ignition module.

In this case, the following error codes should be displayed:

• P3000 (P3001, P3002, P3003, P3004) - ignition in the cylinders does not work;
• P0351 - break in the winding of a pair of cylinders 1-4;
• P0352 - break in the winding of a pair of 2-3 cylinders.

Procedure for checking the ignition module on a Chevrolet Niva

Before proceeding with dismantling the module, you need to make sure that the cause of unstable operation is not a simple lack of power contact. To do this, we “move” or turn on and off the connected block of wires several times. If such a procedure does not bring any results, then the functionality should be checked on a dismantled device.

The values ​​on the multimeter are normal.

1. When the element is removed, we prepare the multimeter for use and check the integrity and cleanliness of the sockets on the terminals (A, B, C, D - approx.).
2. First of all, connect the red probe to contact – D, the second one to ground. We turn the multimeter into voltmeter mode - 20 volts, and if the socket is working, then the readings on the tester should be 12 volts.
3. Next, go to contact – C, the second again to ground. We switch the multimeter to the ohmmeter mode and look at the readings of the device, and if it is less than 1 ohm, then the socket is normal.
4. We check contacts A and B one by one, but in the same order. We connect the multimeter in voltmeter mode and if the readings do not exceed 0.3 volts, then the device can be considered fully working.

If any measurement shows results that do not meet the standards, then you should look for problems immediately in the coil circuit.

Transferring the ignition module

The ignition module has been moved higher

As already written above, for better operation of the ignition module, it is recommended to move it higher in the engine compartment.

When is there an option to repair?

If during testing both secondary windings show integrity and serviceability, the reason for the inoperability of the coils may be a break in the soldering of the switch wires. Such damage is detected when the rear cover of the module is removed. If you have a soldering iron and know how to use it, you can restore the integrity of damaged contacts, while at the same time strengthening the rest. This, unfortunately, is the only failure of the ignition module that can be repaired.

Testing the ignition module can be done using simple do-it-yourself instruments. Based on our advice, you will be able to fully check both the module itself and other elements of the mechanism that may be the cause of the breakdown. We wish you success in this matter!

Module replacement

How to remove and connection order:

The ignition module (IM) is an electrical device whose main task is to generate high voltage current and subsequently transmit it to the spark plugs. High-voltage wires are used to connect the MH and spark plugs. MZ made it possible to abandon the traditional distributor and ignition coil. The ignition system does not require maintenance due to the absence of adjustments and moving parts.

The principle of operation of the ignition module VAZ 21214

The MH control is performed by the Electronic Control Unit, which supplies current to the coil windings. After which a high voltage is generated (according to the law of induction) and at the required moment it is supplied to the spark plug. MZ consists of two ignition coils, two switches, four outputs to high-voltage wires and a plastic case. The ignition system uses the “Cold Spark” method - each coil is connected to two cylinders: the first - the first and fourth cylinders, the second coil - the second and third cylinders.

Symptoms of a problem

Four signs of malfunctioning MH: Loss of power; Dips during acceleration; Cylinders 1-4 or 2-3 do not work; Unstable idle.

How to find the ignition module?

To find the MH, you need to find high-voltage wires, because one end of the explosive wire goes to the spark plugs, and the other to the ignition module.

Connecting explosive wires to the ignition module

In the process of connecting high-voltage wires to the MZ VAZ 21214, a certain order must be followed. If the module is held strictly in front of you, the connection will be made as follows: the first cylinder is connected to the lower left terminal, the second is connected to the upper left terminal, the third to the upper right terminal, and the fourth to the lower right terminal.

The cost of the ignition module for VAZ 21214

The approximate cost is from 650 to 1100 rubles.

The ignition coil on a VAZ 2121 and Niva 2131 is removed for replacement in case of failure. The coil cannot be repaired and must be replaced. To carry out repair work, you will need a standard set of tools, after which, if you have everything necessary, do the following sequence of actions:

Open the hood. The work is carried out with the ignition turned off; you can also disconnect the minus terminal from the battery.

• Disconnect the central high-voltage wire from the coil by removing its rubber cap and pulling the wire toward you.
• Next, using an eight-mm wrench, unscrew the two nuts securing the tips of the low-voltage supply wires to the coil studs and remove them together with the washers.

Now you can remove the coil. To do this, use a ten-point socket to unscrew the two nuts securing the coil bracket to the body studs and remove it.

At this point, the repair work on removing and replacing the ignition coil on the VAZ 2121 and Niva 2131 has been completed. Replace it or make any other repairs, after which we carry out the installation in the reverse order.

ATTENTION! The electronic catalog of spare parts intended for reference purposes only! Our company does not sell all spare parts presented in this list. If there is a “Cost” link in the right column, these spare parts are on active sale

Availability in warehouses for details and prices, see the product card. If there is no “Cost” link in the right column, we do not sell such parts and do not accept orders for them.

If there is a “Cost” link in the right column, these spare parts are on active sale. Availability in warehouses for details and prices, see the product card. If there is no “Cost” link in the right column, we do not sell such parts and do not accept orders for them.

Review of manufacturers, article numbers of coils for 8 (16) valve Lada Granta

*prices are current as of November 7, 2018.

Another online store selling spare parts for the ignition system:

Procedure for checking the ignition module

First of all, you will have to get a multimeter. There is no need to look for any high-precision and expensive instruments. The usual Chinese one will suffice. The main thing is that it has a digital display, this will greatly simplify the measurement. The optimal multimeter in terms of price and functionality is the DT 830 and its numerous modifications. This is one of the most common and easy to use devices. The verification process will be discussed using his example.

First of all, you need to make sure that the primary winding of the Niva-Chevrolet ignition module is intact. For this:

• the switch on the front panel of the device is set to the 200 Ohm position;
• disconnect the connector from the module, remove the high voltage wires;
• sequentially measure the resistance between the middle and extreme contacts of the terminal block;
• The device readings should be within 0.5 Ohm.

The accuracy of a multimeter, of course, is not enough to measure such small quantities, but to check the primary winding for an open circuit, this is quite enough.

The next step is to measure the resistance of the secondary. Sequencing:

• set the range switch DT-830 to position 20 K;
• The probes of the device must first be placed between the high-voltage terminals of cylinders 1 and 4, then 2 and 3;
• the device display should display 5.4 kOhm.

It should be said that it is possible to diagnose a malfunction of the Niva-Chevrolet ignition module only if the readings differ significantly from the norm, or, more often, if “1” lights up on the device indicator. This means an infinitely large resistance, in other words, a winding break.

Some gasoline engines that are installed on modern domestic and imported cars are equipped with ignition modules, which are a pulsed high-voltage current source. There are situations when these devices fail, leading to a complete or partial loss of performance of the car engine. Ways to check for a malfunction in the ignition module in a garage are covered in this article.

List of online stores selling reels (Moscow, St. Petersburg, Kyiv regions)

How to fix a breakdown

As for the question of how to fix a breakdown, there are two options - fast (“field”) and slow (“garage”). In the latter case, everything is simple - it is advisable to completely change the coil, especially if the breakdown is significant. As for quick repairs, either electrical tape or glue is used for this.

Isolating a damaged coil

The most interesting question for car owners in this context is how to eliminate a breakdown of the injection ignition coil? In the simplest case, that is, if there is a small spark breakdown on the body (and this is the most common type of breakdown), after localizing this place you need to use insulating materials (insulating tape, heat shrink, sealant, epoxy glue or similar means, in some In cases, even nail polish is used, but the polish should only be colorless, without any paints or additives), and isolate the place (path) of the breakdown. It is impossible to give universal advice; it all depends on the specific situation.

When performing repairs, it is necessary to clean and degrease the area of ​​electrical breakdown before applying a protective insulating layer to it. This will increase the resistance value of the resulting insulation. If, when the insulation is damaged and there is a breakdown, liquid appears in the coil (usually from a damaged seal), then it makes sense to additionally use dielectric grease.

Well, in the most severe case, you can, of course, install a new coil. It can be original or not - it depends on the price. Many car owners are saved by the so-called “dismantling shops”, that is, places where you can buy spare parts from disassembled cars. They are cheaper there and you can easily find high-quality components.

Finally, a few words about preventive measures that will allow you to get rid of troubles and operate the reel for a very long time and without problems. The simplest measure in this context is to use heat shrink of a suitable (large) diameter, which must be applied to the surface of the tip of the ignition coil. The procedure is simple, the main thing is to choose heat shrink of the appropriate size and diameter, and also have a hair dryer (preferably a construction hair dryer) or some kind of gas burner on hand. However, before applying heat shrink, do not forget to clean and degrease the working surface of the tip. This procedure can also be used not as a preventive measure, but rather as a repair measure.

Also, for prevention, it is advisable to keep the coil housing, and other engine elements, clean so that there is no “sparking” through dirt and dust. And when replacing spark plugs, always use dielectric grease for spark plugs.

The ignition module (IM) of the Niva-Chevrolet car is highly reliable and, most often, provides sparking over many tens of thousands of kilometers. However, if it fails, it is difficult to diagnose due to the lack of obvious signs. The decent cost of a module does not always allow it to be replaced with a new one, which is called “blindly”. First you need to reliably verify that the old one is faulty. Read the article about how to check the ignition module of a Niva-Chevrolet.

Description of the ignition module

Before you learn how to check the ignition module, let's figure out what it is and what kind of MH device it is. The ignition module is the main element of a contactless system, the purpose of which is to generate high-voltage voltage. In turn, this contributes to the formation of a spark on the candles.

Operating principle

How does the ignition module work? The device is powered from the car's electrical network, and the negative terminal of the MH is connected to the vehicle body. The main feature of the MZ is that it can simultaneously supply two sparks. One of them is supplied by the device to the group of spark plugs at the moment of greatest compression of the combustible mixture, the second - at the moment of the injection stroke. One group is the spark plugs of the first and fourth cylinders, and the second is the second and third.

Design

As for the design, the ignition module includes two transformers, as well as. On one side of the MH there are four outputs to which the candles are connected. All structural components are hidden under the plastic body of the device; the weight of the device is more than 1 kg.

New MZ from the manufacturer Bosch

The MH is connected to the spark plugs by connecting high-voltage cables. The control option is performed by the built-in controller. This element makes one decision or another based on the information received about the crankshaft speed and engine temperature, the load on the power unit, etc. As for the operating temperature range, it is quite wide - from 40 degrees below zero to 130 degrees above zero.

Possible malfunctions and ways to eliminate them

The ignition module, like any other device, can fail over time. Before checking the unit, you need to make sure that the symptoms of failure indicate its functionality.

So, what are the signs of a faulty ignition module:

• there is intermittency in idle speed;
• engine power decreases;
• malfunctions occur in the operation of the power unit;
• Twin cylinders may not function correctly.

In addition, if the ignition module is not working correctly, a Check indicator may appear on the control panel. In addition, if symptoms of a breakdown are detected, you should make sure that the high-voltage cables are securely connected to the spark plugs, and that the latter, in turn, are working and intact (the author of the video about diagnosing the device at home is Igor Belov).

https://youtube.com/watch?v=4wHGBUx6x3M

Symptoms of a problem

How to correctly set the ignition on Izh Jupiter 5
As already mentioned, symptoms of a faulty ignition module are also typical for many other components of the car. There are almost no signs that directly indicate MH. This significantly complicates repairs. However, with experience, conclusions about a malfunction of the Chevrolet Niva ignition module can be drawn from the following symptoms.

1. Two cylinders are not firing at once. This is the only sign that, although not always, indicates MH. The likelihood of this increases if cylinders 1 and 4 or cylinders 2 and 3 are not working at the same time.
2. Idle speed “floats”.
3. Diagnostics shows misfires in all cylinders.
4. As the engine warms up, its power drops and interruptions appear.
5. The CHECK ENGIN alarm comes on.

Also interesting: Diagram and pinout of the Niva 4x4 instrument panel (VAZ 2121, 2131) » Lada.Online

It should be noted that a complete failure of the motor, in which the engine does not start at all, happens very rarely. Basically, this symptom of a malfunction of the Niva-Chevrolet ignition module indicates damage to the low-voltage part of the wiring.

Often the cause of problems with the Niva Chevrolet ignition module are breaks in the second winding, because it is this that generates the high voltage pulse. This mainly happens due to the fault of car owners:

• in case of untimely replacement of failed high-voltage wires
• installing spark plugs that do not match the car model.
• moisture ingress due to improper washing

Also, the cause of burnout may be delamination of the solder due to increased vibration during frequent use of the engine at high speeds or during frequent temperature exposure - engine overheating.

Problems with the ignition module can be determined in advance, since two coils do not fail at the same time, so car owners will still have the engine start, but with some difficulties:

• it takes a long time to gain working momentum
• floating idle speed
• excessive engine vibration
• jerking while driving

But these problems may be associated not only with the ignition module, so before replacing it is recommended to check its condition

We disassemble the design of the ignition module of a modern injector

As an example, consider a similar device used on injection VAZ cars. The module operates according to the good old principle: 12 volt power is supplied to the input, and a high voltage is generated at the output contacts for sparking.

The control is electronic, but the operating principles differ from a simple distributorless ignition system:

• All components are located in one housing. On the one hand, this is convenient - fewer wires and contacts - lower probability of breakdown. On the other hand, if the ignition module burns out, it must be repaired; simply replacing the failed element will not work.
• The device is compact and can be conveniently placed in the engine compartment.
• The ignition module is powered at low voltage, which increases the reliability of the device.
• The cost of the finished device is low.
• This ignition module has two coils. This contributes to the survivability of the device - each transformer is loaded twice as much.

The secret of the module’s operation is as follows: it uses not four, but two coils for 4 cylinders. Masters of the old school call this device a two-spark bobbin. Alternating connection of each coil produces two sparks: working and idle. Due to proper distribution among the spark plugs, the idle spark is ignited at the moment when there is no air-fuel mixture in the corresponding cylinder.

The signal for sparking is given by the switch (acting as an electronic distributor). Before checking the ignition module, you need to make sure that control pulses are coming to the contact blocks from the switch.

This block is responsible for the so-called ignition advance, that is, it generates a signal at the right moment. The control pulse about the position of the crankshaft is issued by the Hall sensor, which also synchronizes the operation of the entire system.

Making the right choice

It is best to choose the original, guided by the VIN code of the car. Since the ignition coil is located somewhere in the middle of the ignition circuit, it reacts sharply to any deviations from the characteristics specified by the vehicle manufacturer. For example, if a spark plug requires more energy than the coil can provide, the latter will simply burn out. You can get another “bonus”: if the spark gap is very large , the high voltage will try to find a workaround, that is, it will break through the insulation.

You can also go to your dealer and provide him with information about the following:

• Auto engine;
• Model;
• Year of issue;
• Vehicle body type.

He will select the coil even if non-standard equipment has been installed. Or you can simply remove the coil and ask the dealer to find the same or an identical replacement.