How to replace the parking light bulb in a car?

General information

To indicate the vehicle at night when parked, the design provides side lights. They are present both in front and behind the car. Usually these are low-power lamps, which, unlike the head light, are not in the focus of the reflector. For this simple reason, it makes no sense to install more powerful halogen or LED lamps. Moreover, this can lead to melting of the wiring, which is not designed to withstand such a large load.

As for the reasons for the failure of side lights, there are several of them. Firstly, the light bulb has a limited lifespan. The original shines longer and better, but it is more expensive. Chinese analogues are cheap, but very often burn out. Another reason is a malfunction in the electrical circuit, as well as a leak in the headlight, which causes moisture to get inside the housing. Well, now let's figure out how to replace the side light bulb on a Kalina.

Replacing side lights on domestic cars, using the example of Lada cars

First of all, you need to find the negative terminal on the car battery and disconnect it. Many drivers make the mistake of ignoring this rule, but for safety reasons this rule should not be ignored. In this case, baseless bulbs are suitable; there should be no problems with finding and purchasing them; they are sold in almost every car store and are in wide demand.

Naturally, replacing light bulbs occurs with the hood open, so the next step is to remove the protection - the headlight housing of the car. The protective cover is located exactly opposite the section responsible for the high beam. It will be necessary to remove the yellow cartridge. Finding the cartridge should not be difficult; after removing the casing, it will be immediately visible. The maximum difficulty will be that the location is not very convenient, and dismantling the cartridge will be a little problematic, but you can do it. And if you remove the brown high beam chip, then there will be a little more space, and it will be more convenient to work with your fingers. You should not use pliers in your work, because the cartridge can easily be broken, and you will have to look for a new one, so you should still limit yourself to working with just your hands.

Sometimes it may take more effort to get the cartridge out, and if it doesn’t give in, you just need to twist it a little left and right, slightly pulling it towards you, and then it will definitely come out. After the socket is in your hands, take out the burnt out light bulb and install a new one. Then, you need to return the socket with a new light bulb to its place, inserting it back into the seat until it clicks. If the high beam chip was removed for dismantling, you must remember to return it to its place. Next, you will need to check the light bulb by turning on the light. If everything went well, the light bulb works, then we return the headlight housing to its place, close the hood, and you can get ready to hit the road again, now your side lights are fully operational.

The replacement scheme in this case is quite simple, and no difficulties should arise. You can consider another example of replacing side lights on a foreign-made car.

Required Tools

Replacing side lamps on a Renault Logan will require the use of the following tools and materials:

• clean fabric or rubber gloves;
• 4 pieces of halogen bulbs with W5W base;
• alcohol for cleaning flasks;
• a screwdriver with a cross blade;
• keys for 8 and 10;
• to remove the battery you will need a 13mm socket;
• extension;
• rags.

The presence of gloves allows you to keep the bulbs of halogen devices clean. Oily hand stains cause rapid formation of dark spots and lead to failure of the light bulb. The light becomes dim and uneven, quickly losing brightness. In this case, the service life is reduced by 5-10 times from that declared by the manufacturers.

Where is the marker lamp located, its functions

Front and rear lights ensure the safety of both the vehicle and pedestrians. They light up in the dark when moving, and also remain on when the car is parked on the roadway or side of the road.

The main function of any size is to attract the attention of other drivers in the dark and show them the size of the car. During the daytime, these lighting elements are not used, since bright sunlight makes them dim and almost invisible.

The front marker lights must be white and remain on continuously at night and in poor visibility conditions. This instruction is contained in the traffic rules and must be followed by all drivers without exception.

The rear side lamps are also located on the same line and, according to the requirements, must be red.

Important! Tail lights, regardless of what type of lamps are installed in them, should not shine brighter than brake lights and direction indicators. And if for some reason one of the elements does not light, the violator may receive a fine.

If a malfunction is detected and the lights burn out, you should immediately replace the failed element. You can find many different videos on the Internet on how to replace a side lamp on different Nissan Qashqai models.

On Nissan Qashqai 2011–2012, as well as all other models, the front dimensions are located in the headlights.

When is the replacement made?

Vehicle manufacturers do not provide clear regulations for carrying out this work. There are only 3 reasons why car enthusiasts change their side light bulbs to new ones as needed:

1. The light elements have failed - they have burned out or gone out due to external mechanical influence.
2. The owner of the car decided to install more modern LED bulbs.
3. The lights began to shine too dimly.

The first reason is clear and does not require explanation. Installing LEDs is a useful operation, since these elements shine well, last a long time and consume much less electricity. The main thing is to maintain the polarity of the contacts during the replacement process, otherwise the new light bulb may fail or the fuses will begin to blow.

As a rule, a car enthusiast does not pay attention to the decrease in the luminous flux of running lights until he replaces one burnt-out headlight bulb. Then it becomes noticeable how much dimmer the old element burns than the new one. The reason is the internal darkening of the base glass from settling metal particles emanating from the heated spiral. Therefore, it is recommended to update old “dimensions” in pairs.

Replacing taillight bulbs on a Toyota Camry

• open the trunk;
• carefully unfasten the cover trim;
• find the insert for the side light bulb;
• turn the light bulb socket 1/4 counterclockwise;
• disconnect the contact and remove the light bulb;
• install a new one in its place, proceeding in reverse order.

Replacing taillight bulbs on a Toyota Camry

If there is a need to completely remove the headlight, you will have to unscrew it with a key in three fastening places. A quick self-replacement of the rear tail light of the Camry 50 is completed; all that remains is to return the trunk lid trim to its place.

Often, replacing light bulbs in a Toyota Camry occurs as part of a small optics tuning. Experts recommend using certified lighting devices, purchasing them from official dealers or licensed auto parts stores. When tuning optics, give preference to modern LED bulbs, which have a longer service life and are less likely to fail.

Reasons for replacing the side light bulbs

Replacing lamps in restyled and pre-restyled cars is different. As a rule, in the first case, replacement is somewhat more difficult. Nowadays, replacements do not need to be made so often because LEDs have replaced the old incandescent lamps.

However, there are situations in which replacement is definitely worthwhile.

1. You want to improve the appearance of your car and get brighter bulbs. It is worth remembering that LEDs combine well with cold xenon.
2. You want to increase the life of your side lights. LEDs have a longer lifespan than incandescent bulbs.
3. You want to reduce the amount of electricity you consume or simply keep up with current technological trends.

The reasons for the lamp malfunction may lie in a manufacturing defect. Cheap Chinese lamps quite often fail before the stated end of their service life. Also, the malfunction may be hidden in the car’s electrical network or a leak in the headlight.

Additionally, we recommend reading our specialist’s article, which describes how to change the low beam light bulb on a Priora.

You can read about how to replace the license plate lamp in the material of our specialist.

We also recommend reading an expert’s article on how to replace a low beam light bulb without problems or unpleasant consequences.

Power parameters of all lamps

How to Choose Suitable Replacement Parking Lights

You can choose a suitable lamp both in car services and at car flea markets. At the same time, experienced drivers do not recommend purchasing cheap Chinese products, since the likelihood that they will burn out ahead of schedule is quite high.

When choosing a light bulb, you need to pay attention to the following characteristics.

1. Brightness _ This is the most important characteristic of a light bulb, which is assessed by its luminous flux. Luminous flux is measured in lumens. For an incandescent lamp this value is approximately 50 lumens. Remember that the purpose of side lights is to inform other road users of the size of your vehicle. Light sources should not dazzle other road users, but at the same time they cannot be too dim. The upper threshold of luminous flux for side lights is 150 lumens, and the lower threshold is from 50 lumens. Traffic safety sometimes directly depends on the brightness of the side lights, since failure to inform in a timely manner that your vehicle is starting to slow down can lead to an accident.
2. Construction . In the design of cheap Chinese light bulbs, the base is made of plastic. In this case, there is a high risk of melting, since plastic is by no means a heat-resistant material. If the part gets very hot, the plastic begins to melt and, as a result, the light bulb fails too early. More expensive models feature high-quality plastic that is heat-resistant. With increased brightness, the incandescent lamp begins to produce heat, which heats the lampshade. Therefore, recently the most popular are baseless lamps, the contacts of which are made on the basis of a glass plate and a sand board. Incandescent lamps are also very energy-intensive. With increased electricity consumption, fuel consumption begins to increase. When choosing a light bulb, it is also worth remembering to save energy.
3. Price . The side light bulb is one of those car parts that you definitely shouldn’t skimp on. By buying lamps at low prices, you run the risk of replacing such lamps too often, and in the end, such “savings” will only lead to more serious expenses. It is best to purchase lamps from trusted manufacturers such as Osram and Phillips.

How to disassemble an LED lamp

First of all, it is necessary to check the voltage supply to the cartridge contacts. To do this, screw in a working lamp; if the light comes on, the previous device is faulty.

The reasons for the failure of an LED lamp can be very different - the diode is burned out or the board is not in order.

They often stop working due to condensation that has accumulated inside the housing. In any case, the LED lamp needs to be repaired with preliminary disassembly of the structure.

The components of an LED lamp are:

• shell;
• base;
• matrix with a package of LEDs;
• diffuser;
• driver.

The lamp bulb is not airtight because there are no gases in it. The shell can be made of either plastic or glass. The plastic light diffuser is located at the top.

The LED lamp bases used are varied. The components of the package are groups of LEDs soldered onto PCB or aluminum boards.

Drivers in the form of individual blocks or built into the housing serve to transform the input voltage to a value most suitable for LEDs assembled in groups. The most popular power supply schemes are transformer type.

To make the inside accessible, you need to open the fastening clips that hold the diffuser dome. If it is attached to the housing with screws, they must be unscrewed.

There is another disassembly method used for devices made using sealant sizing. For implementation you will need a syringe with a needle, an awl, and a solvent. To detach the diffuser, you will need to remove the sealant that secures it to the retaining ring.

An awl is passed along the edge and the solvent with which the syringe is filled is injected into the groove. After 30 seconds, the diffuser is removed by twisting. The radiator is removed using a screwdriver, and the LED matrix is ​​unsoldered.

A burnt-out LED can be easily identified visually. It reveals itself by having a black dot. As an option, to make the lamp work again, a jumper is placed at the edges of the unusable LED, but it is better to replace it with a new one.

How to replace the side light bulb in restyled models

Before replacing a light bulb, it is advisable to place the car on a relatively flat surface so as not to tilt again, and also turn off the engine. This way you will avoid electric shock, which is supplied to the light bulb when the engine is on. To avoid a short circuit during operation, on most cars it would be a good idea to disconnect the negative terminal of the battery. It is always better to start replacing from the right side. The headlight unit is equipped with a plastic cover. It is dismantled using a socket and extension.

There may be some minor additional complications with this operation. The socket with a light bulb is sometimes more difficult to get due to the fact that it is quite small in size and is located in a hard-to-reach place. To remove this cartridge, find it and start rocking it up and down until the cartridge is completely removed. There is no need to rotate the chuck.

Start installation work from the side where the washer fluid reservoir is installed. Then you should move on to the headlight installed on the battery side. The cartridge on this side is more difficult to reach due to the body. While removing, use your hand to lift the part up.

The dismantling process requires the presence of a special tool. Manufacturers place a protrusion on the lamp socket. Use a flat blade screwdriver to grab onto this tab and use a lever action to remove the cartridge.

How to properly disassemble a light bulb: instructions for disassembling various types of lamps

To make something interesting with their own hands, DIY enthusiasts implement non-standard ideas using improvised means. A use was also found for the ordinary bulb of a burnt-out incandescent lamp. But fluorescent and LED ones are not suitable for these purposes; they are disassembled only for repairs.

In any case, it is important to know how to disassemble the light bulb, and then you can experiment with its further use.

We suggest you understand the intricacies of this process. The article describes in detail how to act correctly if there is a need to open and disassemble various types of lighting fixtures. In addition, we have prepared interesting homemade solutions from old incandescent light bulbs.

Replacing side light bulbs in pre-restyling models

To do this, you must first prepare the car as indicated above (place it on a flat surface and turn off the engine), and then begin installation work.

1. Open the hood and disconnect the negative cable from the battery (to avoid a short circuit).
2. Remove the plugs that go to the lamps, and then remove the element into which the plug is installed.
3. Turn the light bulb clockwise 45 - 60 degrees, then remove the spare part. To remove the lamp, gently pull it towards you. The socket itself first rotates along with the light source, then it is removed.
4. Install a new light bulb and carry out the reverse dismantling.

How to change a headlight bulb without removing the optics?

There are two ways to access the headlight to replace the Camry 40 size: from the wheel arch side and from the bumper side.

How to change a headlight bulb without removing the optics?

In the first case, this task is much easier to implement:

• turn the steering wheel in the direction opposite to the location of the headlight (if we change the bulbs in the left front headlight, then turn the wheel to the right, and vice versa);
• remove the wheel arch protection clamps and move it to the side by hand;
• take the base of the lamp and turn it 15 degrees counterclockwise, pulling it out of the socket;
• press the latch of the lamp socket connector with your finger and remove it completely from the headlight along with the socket.

How to change a headlight bulb without removing the optics?

If the lamp burns out, it must be replaced with a new one. To replace a Toyota Camry v40 light bulb, you will need model 2825 (W5W). If there is a need to replace the high beam headlight bulb, you should purchase model HB3 (9005) in advance. The low beam requires an H11 bulb, and the turn signal requires a 7440A.

It is not difficult to determine where exactly the headlight bulb on a Toyota Camry 40 is located: it is located slightly above the turn signal bulb. You can recognize the side light bulb by the black color of the socket. You can remove it in the same way as described above: take it by the base and turn it 1/4 turn counterclockwise, disconnecting the cartridge and the power supply. A new light bulb is installed using the same principle - you need to insert it into the socket and return it to its original place in the headlight housing, turning the base 15 degrees clockwise. In the same way, you can replace the high and low beam lamps, as well as the turn signal bulb.

Instructions for replacing lamps

Inside the headlight units of different cars there are 2 types of lamps and connectors - old and new (restyling). Replacing a pre-restyling type side light bulb is performed as follows:

1. Once you reach the back of the headlight, disconnect the power supply connector to the light element. There is no need to disconnect the sockets of powerful headlight lamps.
2. Grasp the connector and rotate 45–60° counterclockwise. Remove the element from the slot.
3. Carefully pull the light bulb out by the base without rotating it around its own axis.
4. Insert the new one in its place, making sure that the contacts line up correctly.
5. Connect the wires and check the functionality of the new part, then reassemble the unit in the reverse order.

Note. On different vehicle models, old-type elements can be rotated in different directions - clockwise and counterclockwise.

When installing a purchased lamp, you should not touch the base with your bare hands, as warned by the instructions included with each product. Before installation, wrap the glass flask with a soft rag or put on cloth gloves.

Updated versions of elements differ in overall dimensions and installation method. Replacing the lamp is done in the same way, only you do not need to disconnect the connectors and turn the socket - the part is removed from the socket along with the wires.

Another thing is that access to the light bulb is often limited - you cannot grasp the socket with your hand. In such cases, 2 options are practiced:

• use a special tool;
• First pull out the large headlight bulb, then take out the side light bulb.

The owners of some cars use the free space behind the headlights to install a gearbox that operates in liquefied gas engine power systems. Removing the unit to replace the lamp can be quite difficult.

Changing the light elements of the rear “dimensions” is much easier. The main work is removing the plastic and fabric trim from the luggage compartment side. The light bulbs are removed from the sockets in the manner described above.

How to remove the headlight to replace the bulb and wash the lens?

You can replace a Toyota Camry light bulb along with cleaning and washing the headlight. If you need to clean the optics from dirt and dust, returning the lens to its former shine, you will have to completely remove the headlight from under the bumper. This is also easy to do, but in this case access to it is only possible through the hood.

Headlight removal algorithm:

• Using a screwdriver, unscrew the two bolts of the metal plate under the seal under the hood;
• remove the metal strip above the headlight;
• unscrew the three bolts securing the headlight itself;
• carefully bend the bumper;
• carefully pull the headlight towards you;
• disconnect the bulbs and connectors;
• remove the optical device.

If the light bulb burns out, you can unscrew it and remove it from the clamp, then install a new one. It is advisable to disassemble the headlight removed from the housing for subsequent washing. To remove the headlight from the car body, you will need an 8” wrench, with which you can remove the electronic corrector. After this, you need to unscrew the fastenings of the rubber seals with a screwdriver and remove the sealing rings (there are only three of them). After the headlight is disassembled, you can wash the inside of it with detergent and distilled water.

Since the 6th generation Toyota Camry has a headlight with partitions, it may be more difficult to remove accumulated dust and dirt. It is recommended to use a small sponge to thoroughly rinse the sections. Some people use a clever method: they cut an ordinary dishwashing sponge into small squares and place them inside the headlight, filling them with water and detergent. In this way, it is possible to remove any remaining dust and dirt from the diffuser as thoroughly as possible.

After all manipulations with water, the headlight must be thoroughly dried before replacing the light bulb of the Camry 40 size. Before this, the headlight must be assembled in the reverse order:

• install the corrector using an 8” wrench;
• put all the rubber seals in place, securing them with standard fasteners using a flat screwdriver;
• Turn the headlight adjusters so that the holes for the lamp are in the center.

The same method is suitable for other cars of this brand. There may be differences in the optics of different models, so it is recommended to first study the registration certificate of a foreign car.

How to change the side light bulb yourself?

Driving a car with inoperative “dimensions” is prohibited by the rules - any traffic police officer who records such a violation has the right to issue a fine to the driver. To replace a side light bulb that has burned out and gone out, you do not need to visit a car service center - every car enthusiast can perform this operation. The following instructions describe how to make the replacement correctly.

Side light circuit

It's very easy to replace the side light bulb yourself.

In order to save fuel and reduce the load on the generator, daytime running lights are now often included in this circuit, which makes it quite complicated.

You might be interested to know whether it is possible to use LED lamps in a car? Read more in this article

The standard wiring option is quite simple and consists of the following elements:

• circuit breakers;
• front and rear position lamps;
• central or key switch;
• Let's take a closer look at the first two elements.

Circuit breakers

Sometimes blown fuses are the reason why the side lights do not light up on one side or another.

There are usually two fuses in the circuit, for the left and right sides separately. Since the light bulbs consume little power (4-5 W each), the fuse rating is small, only 5-7.5 A.

Where are the side light fuses located?

In the same place as the others, in a single block. On most modern cars, this block is located under the instrument panel next to the steering column, or, more often, on the lower left, under a plastic trim.

In the latter case, it is enough to remove the cover protecting the unit, mounted on latches. On the back of the cover, as a rule, there is a sticker with information about which circuit this or that fuse protects, indicating its rating.

The biggest inconvenience in this case may be insufficient knowledge of the English language - it is in this language that inscriptions are usually made, even on Korean and Japanese cars.

Lamps

Externally, the headlight bulb is marked W5W, but today LED sidelight bulbs are increasingly used.

Their advantage over incandescent lamps is their greater durability, and the price of both largely depends on the manufacturer. The most famous products are Philips, Osram, Tesla.

Watch the video about LED bulbs for side lights:

Moreover, as the “Behind the Wheel” test showed, expensive products do not always justify their price.

Also, quite often, the front dimensions are equipped with light bulbs with a metal base, but this, one might say, is a thing of the past.

For rear position lights, the most common lamp is with two spirals - 21 and 5 (or 4) W.

The 21 W coil lights up when you press the brake, i.e. In this case, the light bulb serves as a brake light, while the lower power spiral works as a side light.

Just as with any other lamps, purchasing a more expensive product does not guarantee any exceptional durability.

How to remove a side light bulb

Welcome to the ranks of our friendly company!

Useful

online now

Voting

Club Wallet

Nissan Friendly Clubs

Official sales of the new generation Nissan Tiida hatchback have started in Russia.

The new car is assembled at a Russian car assembly plant and is available in one of 7 trim levels: Welcome, Comfort, Elegance, Elegance Plus, Elegance Connect, Elegance Plus Connect and Tekna.

The cost of the car starts from 839,000 rubles.

For this money, buyers will receive a 1.6-liter gasoline engine producing 117 horsepower, paired with only a five-speed manual transmission. But the most expensive modification of the Nissan Tiida hatchback - the Tekna package - will be offered only with a transmission - a continuously variable variator and at a price of 1,030,000 rubles.

The Welcome starting package offers the following set of equipment: two airbags, anti-lock braking system, stability control system, full power windows and mirrors, a steering wheel with multiple functions, an on-board computer, preparation for an audio system (speakers and wiring), steel wheels with a diameter of 16 inches.

Air conditioning and a music system will be available for 873,000 rubles. This is exactly how much the Comfort package with a manual transmission costs. With a CVT, this equipment can be purchased for 903,000 rubles.

The most expensive Nissan Tiida in the Tekna configuration will cost at least 1,030,000 rubles. In addition to the options listed above, the top-end hatchback is equipped with rain and light sensors, an auto-dimming interior rearview mirror, a keyless entry system and push-button engine start, as well as a NissanConnect navigation system with a color touch screen and a rearview camera.

Replacing lamps

Usually, before replacing light bulbs, it is recommended to remove the terminal from the battery. Why is not clear. It is enough to simply de-energize the circuit using a switch - in case you accidentally short-circuit during replacement.

Replacement of rear marker

To provide access to the taillight lamps, you need to remove the hatches installed in the trunk trim.

To replace the tail light bulbs, it is usually necessary to remove the circuit board with the bulbs from the light. It is installed on latches, which are carefully bent with a flat screwdriver. There is no need to disconnect the wires.

There are also lanterns in which each lamp is connected separately. In this case, remove the desired cartridge from the socket by turning it slightly.

After replacing the lamps of both front and rear lights, you should check their functionality, for which you do not need to install the socket or board directly into the lamp. It is enough just to check that there is no short circuit to ground.

An important point - when replacing dimensions, always pay attention to the condition of the cartridges and contacts - the fuse only protects the circuit from short-circuiting, and fires in the wiring often occur due to poor contact.

Replacing the front marker

The most common option for connecting a headlight unit is to have a single power connector - for ease of dismantling the headlight itself. In this case, the power wires for all consumers (lamps, electrical corrector) are located inside the housing.

However, consumers are often connected separately. Before replacing, the main thing is to determine the location of the side light bulb, so as not to mistakenly remove, say, the headlight range control unit.

If you are changing light bulbs for the first time, it is better to start on the right side. The battery is usually located on the left, which interferes with both visibility and operation.

The replacement process itself is simple - remove the lamp together with the socket from the headlight, for which you turn the latter counterclockwise. The wires do not need to be disconnected if they are long enough to work comfortably.

It is important to pay attention to the condition of the cartridge - whether there are any traces of melting, which indicates overheating. A defective cartridge may subsequently cause a short circuit, so do not delay replacing it if necessary.

And here about what xenon and bi-xenon are, what is their difference https://mytopgear.ru/interesting/ee/ksenon-i-biksenon-v-chem-raznitsa/

Replacement process

The rear lights are attached to the body of a VAZ 21099, 2108 or 2109 car using 4 nuts.
To dismantle the lighting system you will need: The operating algorithm is as follows:

• To access the nuts, remove the 21099 luggage rack at the appropriate location (if the rack is installed).
• Disconnect the power plug that is attached to the board.
• Unscrew the 4 nuts using a wrench.
• When removing the last nut, hold the taillight outside to prevent it from falling and breaking.
• After removing all 4 nuts, remove the light.

When installing a new headlight on the rear of model 21099, do not forget to connect the wiring to ground, which is attached to one of the studs.

In such cases, the ride becomes quiet, calm and relaxed, but how everything changes when at least one light bulb burns out. This causes inconvenience and emergency situations, and you can also get a fine from a road service employee.

The dimensions on the VAZ 2109 do not light up, then look for the reason in the wiring. Even experienced drivers recommend carefully checking the functionality of all devices and components before leaving. The nine is no exception, in which optics can often fail for various reasons, including:

The rear lights (headlights) of the VAZ 2108, VAZ 2109, VAZ 21099 have the following bulbs: 1) Brake lights. 2) Dimensions. 3) Reverse. 4) Turns. 5) Fog lamp.

Rear light board for VAZ 2108, VAZ 2109, VAZ 21099

A wiring harness goes from the mounting block to the rear lights. The purpose of each individual wire in the harness can be understood by its color: 1) Brake lights - red 2) Dimensions - yellow 3) Reverse - green. 4) Turns - blue. 5) Fog light - orange-black.

We remove the connector from the rear light board of VAZ 2108, VAZ 2109, VAZ 21099

Naturally, you need to understand that if the car VAZ 2108, VAZ 2109, VAZ 21099 is old and there are a lot of people doing the wiring, then the color match of the wire to its purpose may be violated. That is, the red wire can be converted not to brake lights, but, for example, to dimensions. But in general this is a very important point: the developers of the VAZ 2108, VAZ 2109, VAZ 21099 specifically marked the functional purpose of the wires with a certain color to make it easier to use.

Flashlight board VAZ 2108, VAZ 2109, VAZ 21099

If some light signal in the taillight of a VAZ 2108, VAZ 2109, VAZ 21099 does not work, then before climbing into the mounting block and opening the electrical circuit, we check the following: 1) The reliability of fastening the mass of the taillight to the body of the VAZ 2108, VAZ 2109, VAZ 21099.2)

We check the reliability of fastening the wire connector to the headlight. 3) Integrity of the light bulb 4) Quality of contact between the light bulb and the flashlight board. It often happens that everything is intact, the light bulb and the mass are good, and 12 Volts come to the light bulb, but it does not light. The reason is poor contact between the light bulb and the board. In this case, you need to clean both the light bulb base and the area on the lantern with fine sandpaper.

As one smart person said: “Electrics is the science of contacts.” To disassemble the rear light of a VAZ 2108, VAZ 2109, VAZ 21099, first remove the protective plastic cover. Then disconnect the black wire of the flashlight from ground. Then we remove the connector from the flashlight board and remove the board itself with the bulbs from the headlight housing. If it is necessary to replace the headlight itself, then unscrew the remaining bolts securing the headlight to the car frame and remove it.

Flashlight housing VAZ 2108, VAZ 2109, VAZ 21099

There is one important point that many owners of VAZ 2108, VAZ 2109, VAZ 21099 do not know. This is the rear fog light. It is turned on by a button between the hazard warning button and the heated rear window. The rear fog light will only work if: 1) The ignition is turned on. 2) Low beam headlights are on. 3) The flashlight power button is pressed. The fog lamp lamp for VAZ 2108, VAZ 2109, VAZ 21099 is the only one that has a reflector inside the headlight. Thanks to this reflector, the glow of the lantern becomes brighter.

The clearance of VAZ 2108, VAZ 2109, VAZ 21099 is included

Rear fog light on VAZ 2108, VAZ 2109, VAZ 21099

Power of rear light bulbs VAZ 2108, VAZ 2109, VAZ 21099: Dimensions 5 Watt Fog light 21 Watt Reverse 21 Watt Stop light 21 Watt Turn signal 21 Watt

Preparation Tips

To replace two side light bulbs, you do not need to create special conditions and drive the car into the garage - the work is carried out in any convenient place. What to do:

1. Disconnect the negative terminal of the battery.
2. Remove components and parts that block access to the headlight units from the engine compartment.
3. Remove the plastic protective caps covering the rear parts of the blocks where the light fixtures are located.

To change the side light bulb, you need to get to the headlights from the rear, having first removed the interfering elements. Depending on the make and model of the car, there may be an air filter housing, a battery, cooling system pipes, and so on near the headlight units. Decorative plastic panels and trims should also be removed.

Let's sum it up

On some modern premium cars, it is not possible to even change a light bulb yourself. Whether this is good or bad, we cannot say for sure. But on budget models this option is available. Moreover, it is advisable to carry out the replacement yourself, because there is nothing complicated or impossible here.

Visiting a service station to replace a marker lamp is not the best solution. This way you will waste much more money and precious time. And when you replace it yourself, you will gain valuable experience that will be useful in the future. It is recommended to take a burnt-out lamp to a car dealership and buy a similar one. You shouldn’t chase more powerful lighting devices, they usually only bring problems. On some brands of cars, like Renault Logan, it is more difficult to replace a lamp than on others. But nothing is impossible, so it’s definitely worth addressing this issue.