Rear view mirrors are important elements of any car that ensure traffic safety. High-quality mirrors allow the driver to fully control the situation on the road. The standard mirrors of the VAZ 2107 do not meet modern requirements. Therefore, owners of sevens are trying to modify them or replace them with more functional models.
- Types of mirrors for VAZ 2107
Universal mirrors - Enhanced view mirrors
- F1 mirrors for tuning
- Mirrors designed specifically for the VAZ 2107
Photo gallery: mirrors for VAZ 2107 produced by NPK POLYTECH
- Table: technical characteristics of mirrors produced by NPK POLYTECH
- Panoramic rear view mirror
- Video: replacing mirrors on a VAZ 2107
- Applying chrome vinyl film to the mirror body
Video: applying chrome vinyl film to the mirror body
Instructions for complete disassembly of the side mirror of a VAZ 2110
How to disassemble the side mirror on a gilly mk: Atlas Auto
Instructions for complete disassembly of the Nexia side mirror. Instructions for complete disassembly. Instructions for complete disassembly of the Nexia side mirror. This instruction is general because Everyone can see in it the disassembly of the mirror exactly to the extent that he needs: someone needs to remove only the mirror element to install heated mirrors, someone needs to fix an adjustment cable that has flown out. Therefore, if you only need to remove the mirror element, there is no need to disassemble the mirror down to the last screw. We snap off the plastic triangle in the interior that covers the mirror mounting screws. Then unscrew the fastening screws and remove the mirror from the car. Carefully remove the first rubber gasket, because It is quite problematic to purchase new ones; they are rarely sold separately for repairs. Similarly, remove the second rubber gasket. Unscrew the two screws.
Download instructions for completely disassembling the side mirror of a VAZ
Then at one end of the wire we cut an m3 thread approximately 15 mm long, looking at Fig. 5, we insert it into the body of the future mirror. The wire should pass through the washer and then through the entire spring. Screw both nuts onto the wire and place one end of the spring on the bracket Fig. 7. The free end of the wire protruding from the side of the triangle (Fig. 5) must be firmly secured to something “immovable”. Or, twist a loop and put it on your own foot’s boot to check your deadlifting strength! In general, we pull the body of the mystery mirror “towards ourselves” as hard as we can until the assistant finally inserts the fixing key into place Fig. 5. Note: Swapping with an assistant is possible. The need to remove the side rear view mirrors of a VAZ 2110 may arise for various reasons, for example, for painting, installing heating, or completely replacing them. Disassembly is therefore necessary to carry out repairs or any other modifications. How to remove the rear view mirrors of a VAZ 2110 detailed instructions. Pry up the rearview mirror control knob cap and unscrew the mounting screw with a Phillips screwdriver. Remove the triangular plug by prying it up with a flat-head screwdriver, carefully releasing the latches as you do so. Next, unscrew the three screws that secure the mirror to the base, using the same Phillips screwdriver. You can remove the mirror element from the body in several ways: Dismantling the mirror, pressing on the central part of the mirror from the inside, and snap it off.
Dismantling and disassembling the rear view mirror of the VAZ-2110
There are many reasons for disassembling a car side mirror. This may be a desire to paint it, or to put it in order after its channels were caught by some reckless driver. How to disassemble a car mirror, and before that, how to quickly and easily remove it, is of interest to many car enthusiasts. Due to inept movements, a car mirror can become completely unusable and then it will be necessary to purchase a new one, and as a result, the mirror will be installed in a car service center. But there are many brands and, moreover, models of cars, as well as mirrors for them. There are also many varieties of electric mirrors, folding, with turning elements, and so on. The most important thing is how to remove it so as not to damage it. VAZ 2110, 2. Instructions for. Side mirrors of VAZ 2110. Complete disassembly.
How to disassemble a car mirror - disassembling the side
Removing the side mirror. Disassembling the side mirror. Forums faq on actions for brands and models. Disassembly instructions. Reasons for analyzing the side. Look at the Chinese mirror on the VAZ 2110.
Tuning VAZ: Body
Up. Disassembling the mirror. VAZ 2110 may arise according to. VAZ 2110. Side mirrors.
Complete instructions. Mirrors VAZ 2110: disassembling mirrors. In the housing of the side mirrors of the VAZ 2110. The auto industry has an advantage in the domestic market. Dismantling mirrors. Mirrors VAZ 2110;. Hotpoint ariston oven fz612 1ixha instructions State registration of rights to real estate form Statement of inventory and assessment of fixed assets object form Instructions for fire safety in the painting area
Information
Before placing an order, we recommend that you familiarize yourself with the general information on Payment and Delivery of goods in the online store.
Basic provisions of the online store: 1. All orders are placed through product order form located on the website. 2. Coordination of the completed order is carried out via the email specified by the client in the order form. The client can be advised over the phone on the choice of a particular product. The exception is orders from St. Petersburg - they are agreed upon with the client by phone. 3. Delivery to regions of the Russian Federation and CIS countries is carried out by Russian Post , cash on delivery or 100% prepayment. Estimated delivery times for orders to Russian regions are 5-15 working days. 4. The cost of delivery of goods is calculated individually for each order, based on the remoteness of the customer’s region, the weight of the parcel and the chosen payment method for the order. The final cost of order delivery is indicated in the letter confirming the order. Read more about delivery and payment here. 5. Orders and delivery to the CIS countries and neighboring countries are carried out only on the basis of 100% prepayment. 6. Goods of good quality can be returned within 7 days from the date of receipt. 7. Product warranty - one year from the date of purchase.
Cost of covers for Kalina mirrors
They cost on average from 500 to 1000 rubles, depending on the shape, color and method of attachment. Unpainted overlays can be purchased for only 200 rubles. Chinese cheap analogues cost very little (100-300 rubles), but are significantly inferior in quality. They are more fragile, brittle and inelastic.
Mirror covers for the Lada Kalina are the simplest but most noticeable tuning element!
The VAZ service station provides complete diagnostics and repairs of the Lada Kalina (1118) sedan.
Our car service specialists have extensive experience in maintaining and repairing VAZ vehicles, and thanks to our own auto parts store, we always have the necessary parts in stock.
View the price list for basic VAZ repair work
Prices for our car service services are significantly lower than the market average, which allows you to carry out high-quality repairs at an affordable price.
STO VAZ provides the following types of services:
- Car repair Lada Kalina (1118) sedan;
- Full diagnostics of VAZ 1118: diagnostics of the engine, brake system, suspension, compression measurement;
- Maintenance of Lada Kalina 1118 sedan: changing engine and transmission oil, replacing filters, replacing technical fluids, replacing the brake system and timing belt;
- Repair of the chassis: suspension, clutch, steering, brake system;
- Tire fitting and storage;
- Car wash;
VAZ-1118 is a new model of AVTOVAZ LLC, the production of which began in 2004. This is a five-seater passenger car with front-wheel drive, a front engine and an all-metal welded body. Lada Kalina is distinguished by a reinforced structure of the roof, sills and central pillar. Additionally, safety is ensured by bumpers made of impact-resistant polypropylene. The engine is four-cylinder, four-stroke, in-line, eight-valve, with a displacement of 1.6 liters.
In the basic configuration, Lada offers electric power steering, and as an additional set of options you can choose seat belt pretensioners, air conditioning, airbags, heated front seats, electric rear-view mirrors and an anti-lock brake system. All VAZ-1118 vehicles are equipped with special catalytic exhaust gas converters.
The exterior rear view mirror on the Lada Kalina is designed and dismantled very simply and conveniently, like everything on this model of a domestic car (in my opinion, the best in terms of price-quality ratio).
This particular mirror is suitable for both Tens and Priora. As we can see in the photo above, the mirror mounting principle is the same as on other Ladas, with one small difference. The side mirror is attached to three self-tapping screws using a shaped screwdriver (see photo above).
The side mirror itself (in this case, simple, without a turn signal repeater, with manual adjustment) consists of two parts. The main part (the mirror itself) and the protective cover. Connect these parts carefully and accurately by aligning the grooves on the mirror and the inserts on the lid and press it. It should click into place.
Next, lean the mirror on the outside of the door so that all three guides and the cable connection fall into place (photo above). Then, screw in and tighten the three screws. Make sure that the mirror on the outside of the door is level and properly positioned.
And now, that same “one small difference” - instead of the Zhiguli plastic nut that we screw onto the connection of the control cables, here it is attached to the same Zhiguli corkscrew, which on the classics secures the door lock cylinder. And finally, put on the plastic panel so that the adjustment lever fits into the rubber frame, lean the panel against the two guides in the corresponding holes and press it.
Mirror for Kalina, price 3000 rubles (with mechanical adjustment and without repeater)
Sources
- https://expertvaz.ru/lada-kalina/razobrat-nakladki-zerkala.html
- https://remontvaz.spb.ru/lada-kalina-1118-sedan/
- https://arbi-idirisov.ru/kak-pomenyat-bokovoe-zerkalo-na-kaline/
How to disassemble and repair a rear view mirror?
How to disassemble and repair a rear view mirror? What is needed for disassembly How to remove a mirror How to disassemble a mirror, 2 methods Repair rules
It often happens that the rear view mirror mount becomes loose and the mirror does not hold well or falls off (perhaps someone caught it while driving). It happens that the side mirror is broken or cracked - it needs to be replaced. The mirror angle adjustment drive may need to be repaired. You can contact a car service center and they will attach the mirror in place. But if there is no service nearby, you will have to act independently
The rear view mirror is extremely important on the road: the driver can monitor the situation on the roadway in the viewing area behind the rear fenders and rear bumper. Mirrors on different brands of cars are different: internal mirror and side mirrors, regular, folding, electric and others
When removing and disassembling any mirror, you need to be extremely careful not to damage the mirror itself.
- What is needed for disassembly
- How to remove a mirror
- How to disassemble a mirror, 2 ways
- Repair rules
What is needed for disassembly
In order to disassemble the mirror, you will need the following tool:
• 2 flat screwdrivers (they are used to release the latches).
• A thin, long screwdriver and a piece of soft cloth (to wrap the screwdriver).
• 10mm star wrench or regular screwdriver with interchangeable bits.
How to remove a mirror
How to remove the electric side mirror (assembled):
1. Remove the triangular trim from the front door.
2. Disconnect the mirror wiring connector. Do not damage the mirror heating wiring!
3. Holding the mirror, remove the 3 mounting screws.
4. Remove the mirror assembly.
5. We install the mirror in the reverse order.
Removing the side rear view mirror with a mechanical drive:
1. Remove the mirror adjuster locking bracket.
3.Remove the mirror.
4. Installation is carried out in the reverse order. How to remove a rear view mirror in a carThe most common option for fastening the rear view mirror to the windshield is 2 bolts. Such fasteners are found on domestic cars. To remove the interior mirror, proceed as follows:
1. Remove the caps on the bolts (if any).
2. Holding the mirror, unscrew the mounting bolts.
3.Remove the mirror.4. Wipe the area where the mirror meets the windshield with alcohol.
5. When installing the mirror, you need to make sure that the mirror “sits” in the same place (the spot on the windshield).
On a foreign car, the rear view mirror is glued to the windshield. To remove the mirror from the windshield, follow these steps:
1. Remove all plastic plugs by hand.
2. Moderately pull the mirror up (toward the ceiling).
Apply proper force (when pulling the mirror up). If you overdo it, the windshield may crack. If the mirror has already moved out of place (has come out of the runners of the bracket), and you are still pulling it with force, then you can accidentally cut through the upholstery on the ceiling with a sharp edge. On some car models there is a special lock in the form of a button (you need to press it).
How to disassemble a mirror, 2 ways
To replace a cracked mirror, you need to know how to disassemble a rearview mirror. You can only disassemble the removed mirror: it is both convenient and safe for the mirror itself. Disassembling the rear view mirror can be done in two ways:
• Having previously removed the mirror from the door or windshield. This disassembly method is safer for the entire mirror unit.
How to remove the heater radiator on a Lada Kalina?
We will need:
- Phillips screwdriver;
- Set of wrenches;
- Coolant container;
1). Disconnect the negative terminal of the battery.
2). Remove the windshield frame trim. Remove the battery and air filter housing along with the air duct.
3). Remove the battery from the engine compartment.
4). Drain the coolant and disconnect the heater radiator hoses.
5). Unscrew the screw that secures the heater to the partition of the engine compartment.
6). Remove the heater radiator cap and the heat exchanger itself. The radiator is located under the dashboard in a plastic casing, and therefore the front seats will need to be removed from the interior. Also, the main stage of work, in addition to removing the dashboard, is preceded by the dismantling of the steering column, power steering and central tunnel.
https://youtube.com/watch?v=BJD44p2sUng
How to remove the heater radiator on a VAZ 2110, 2111, 2112
1). Drain the coolant. We unscrew the cap of the expansion tank (so that the pressure drops) and unscrew the drain plug, which is located behind the ignition module (we unscrew it and put it aside). About 4 liters of coolant should run out into a previously placed bucket.
2). Remove the rubber seal of the wind lining (jabot) and the frill itself.
3). We unscrew the screw securing the frill (it is under the main brake cylinder).
4). Unscrew the 4th screws of the upper fastening of the right part of the frill.
5). We unhook 2 clamps on the frill for fastening hoses and wires.
6). Disconnect the negative wire of the fan from the body and the positive terminal.
7). We unscrew the two screws on the left side of the frill and move it a little forward (there is no need to remove it completely).
8). We remove the windshield trim, there are 2 nuts (10 each) and 5 screws.
9). Disconnect the coolant level sensor terminal (if equipped) and remove the steam hose from the expansion tank.
10). Disconnect the windshield washer hose.
eleven). Unscrew the 4th screws.
12). Remove the windshield wipers and remove the windshield trim. We remove the clamps of the heater and fan housing, but not all of them.
13). Heater housing clamps.
14). Unscrew the screws of the cabin filter housing and the front part of the fan housing (all screws are the same except for four long ones, remember their location.
15). Remove the front part of the heater fan housing (with fan).
16). Remove the cabin filter housing.
17). Remove the back of the fan housing.
18). Loosen the clamps and remove the supply hoses, coolant return hoses and steam exhaust hose. With little effort, remove the leaking heater radiator.
19). Clean and reassemble in reverse order.
How to remove the heater radiator on a VAZ 2114, 2115
1). Disconnect the negative terminal from the battery.
2). We drain the liquid from the engine cooling system (there is a special plug at the bottom of the radiator for this purpose).
3). The stove is located on the right side of the front console, so this unit will have to be dismantled.
4). Remove the mounting screws holding the console to the body.
Instructions for dismantling the stove: Remove the glove compartment, unscrew the mounting screws, move the console on the right to a sufficient distance so that you can work. Do not forget to fix the console, otherwise it will constantly interfere, returning to its original position.
5). Disconnect the rubber pipes. To prevent any remaining coolant from getting on the upholstery, I recommend preparing a container where you can drain it.
6). We disassemble the stove body, after which it will be possible to get to the radiator by removing it from its seat.
What kind of mirrors are installed on the VAZ 2106
As mentioned above, the standard exterior mirrors of the Six are not suitable for all car owners.
And there are several reasons for this:
- small size. Since the area of the mirror elements in standard mirrors is very small, the review also leaves much to be desired. In addition to the limited visibility, standard mirrors have blind spots, which also do not contribute to safe driving;
- lack of protective visors. Since the “six” is a rather old car, its exterior mirrors do not have “visors” that protect the surfaces of the mirror elements from rain and sticky snow. So in bad weather the driver is forced to periodically wipe the outside mirrors. It is clear that not everyone likes this;
- The mirrors are not heated. Because of this, the driver is again forced to manually clean the mirrors from ice;
- appearance. The standard mirrors on the “six” can hardly be called masterpieces of design art. It is not surprising that drivers want to get rid of them.
We list the mirrors that drivers install instead of standard ones.
F1 type mirrors
The name F1 was assigned to these mirrors for a reason. In appearance, they resemble the mirrors found on Formula 1 cars. The mirrors are distinguished by a massive rounded body and a long thin leg.
You can purchase them at any store that sells spare parts for car tuning. The owner of the “six” should not have any problems with attaching these mirrors. They are attached to the car using a standard plastic triangle. They are held on by three self-tapping screws. To install the F1 mirrors, you only need a Phillips screwdriver. F1 mirrors have both pros and cons:
- the undoubted advantage of F1 mirrors is their modern appearance;
- mirrors of this type are adjusted from the cockpit using a special lever. This point becomes especially important for the driver in bad weather;
- but the review of the F1 mirrors leaves much to be desired, since the area of the mirror element is small. As a result, the driver has to adjust the mirrors every now and then. This happens every time the driver moves the seat back slightly or changes the angle of the backrest.
Universal type mirrors
Currently, the spare parts market offers the widest range of universal rear-view mirrors for the VAZ 2106. They differ both in quality and in manufacturer. In addition, mounting methods can also differ significantly. When choosing a universal mirror, it makes sense for a novice driver to focus on a standard triangle mount. And only after that look at the appearance of the mirror and viewing angles. The fact is that to install universal mirrors with non-standard mounts, additional holes may be necessary. And drilling neat holes in the car body is not as simple a task as it might seem. There are two types of mounting universal mirrors:
- fastening using a standard triangle;
It should be noted that fastening “behind the frame” has never been reliable. Over time, any fastener can weaken. As soon as this happens to the bolts in the hinges, the mirror will jump out of the housing and will almost certainly break. And this is another argument in favor of choosing fasteners in the form of a triangle.
Video: universal electric mirrors on the VAZ 2106
Large mirrors from Niva
Some drivers prefer to take a radical approach to improving their mirror visibility. And they install vertical rear-view mirrors on their “six” (they are also called “burdocks”). Nowadays native “burdocks” for the “six” are not so easy to find on sale, although literally three years ago the shelves were littered with them. But drivers found a way out of the situation: they began installing large mirrors from the Niva (VAZ 2121) on the VAZ 2106. The visibility after installing such mirrors really improves. But, alas, it’s impossible to call such a solution beautiful: the Niva mirrors on the VAZ 2106 look too bulky.
Such “bugs” can be attached to the “six” using a standard triangle. Only in this case you will have to take two brackets from the VAZ 2106 and Niva mirrors and use them to make a new fastener for a large mirror.
Here we should also mention the new mirrors. As you know, the Niva car was updated relatively recently. This also affected the rear view mirrors. And if the car enthusiast has a choice, then it is better to install mirrors from the new Niva on the “six”.
Despite their small size, they have a good overview. There won’t be any big problems with fastening either: it’s still the same standard triangle, in which you’ll have to drill one extra hole.
Replacing a car mirror
The car mirror of this brand has several advantages:
- The 33B type mirror elements are attached in exactly the same way as the standard models, so there will be no problems with installation.
- The device housing is more durable, well protected from mechanical damage and atmospheric factors.
- The reflective element has a wide viewing angle with minimal blind spots.
- The side mirror has a heating option and a cable drive for position adjustment.
If you do not want to completely change the mirror elements on the VAZ 2107, you can use additional reflectors. These can be spherical circles that are attached directly to the reflective surface or special pads in their own housing. They are installed above the standard mirrors. Thanks to the movable leg, additional mirrors can be adjusted separately from the main ones.
Goods Car store consultants will be happy to help you choose the right interior mirrors for your car from a wide range and give useful tips on caring for them.
Hi all! Today, in the “Tuning” section, I’ll tell you how to inexpensively improve the appearance of the “six” at home by installing rear-view mirrors from the Lada Priora on it. The work is of medium complexity, therefore, with a little experience and “direct hands”, any novice car enthusiast can do it.
By the way, Priora side mirrors are not always installed purely for aesthetic reasons, or the desire to stand out from the crowd, to make the car more attractive. Many people associate the installation of rear-view mirrors from Priora with convenience. The fact is that the owners of the “sixth” know better than anyone that adjusting the side mirrors on these cars is a real pain, especially while driving. In addition, nothing is visible in these insignificantly small mirrors, there is no visibility, so driving in reverse in a “classic” often turns out to be an even more difficult task.
And as often happens in our latitudes, the problem was solved by ordinary “handy people” who, as it turned out, know better what this or that option in a car should look like. Installing a mirror from Priora on a VAZ not only improves visibility, but also, if desired, makes it possible to get another, no less useful option - heated rear-view mirrors.
Before installing side mirrors from Priora on a VAZ 2106, you should prepare:
- Grinder (or hacksaw);
- Set of keys and screwdrivers;
- Putty, fiberglass, sandpaper, primer and paint;
- Mirrors of the Lada Priora, well, “straight hands”.
Replacement of rear view mirrors of VAZ 2107
To dismantle the rear view mirror of a VAZ 2107, you only need a Phillips screwdriver. This is done as follows:
- Lower the glass to its lowest position.
- Near the mirror we move away the sealing rubber of the glass.
Unscrew the bolt from the outside of the glass frame.
Remove the mirror from the glass frame.
On the new mirror, loosen the three screws securing the triangular panel on the side of the adjustment knob so that it fits in place of the standard mirror in the glass frame. Using this panel, the mirror is attached to the glass frame.
We install the new mirror in place of the standard one and tighten the mirror mounting bolts, clamping the mirror onto the glass frame.
We return the glass sealing rubber to its place.
The entire procedure for replacing the HZV will take no more than an hour. If heated or electrically adjustable mirrors are installed, you will have to install controls for these functions in the interior and connect the wiring to them, which, as a rule, comes complete with the ZZV.
Appearance of VAZ 2101-2107 Side mirrors
Side mirrors VAZ 2101, 2102, 2103, 2104, 2105, 2106, 2107
Side mirrors are an important part of a car's equipment, which ensures safety during various maneuvers. With their help, good visibility of obstacles located behind the machine is ensured.
Unfortunately, it is this part of the equipment that fails more often than others. The main cause of breakdown is careless parking. At the same time, the side mirrors on domestic cars are not impressive with their structural strength - a slight push is enough to damage them.
Our online store offers an excellent solution to this problem! The assortment includes a wide selection of side mirrors for VAZ 2101, 2102, 2103, 2104, 2105, 2106, 2107. Drivers can choose a high-quality and reliable model that will ensure strong fixation and will delight you with long-term service. In addition to standard designs, the catalog presents the following options:
- Electrically adjustable. The function is provided through the use of additional wiring and provides maximum driver comfort - you can put the mirror in the desired position without leaving the car!
- With anti-glare. The use of this additional coating ensures good visibility in all conditions and prevents the driver from being blinded. This feature is most useful in sunny weather or when driving in the dark when the mirror creates glare from the headlights.
- With turn signal. Allows you to clearly signal the maneuvers being performed to other road users.
Our assortment also includes models of mirrors for Classics with various designs, which will allow you to find an option that will go well with the design and color of the car.
Other benefits of purchasing
It is also worth noting that all models from the catalog are resistant to environmental influences, which significantly increases their wear resistance. Thus, corrosion does not occur on coatings under the influence of high humidity.
At the same time, side mirrors for VAZ 2101, 2102, 2103, 2104, 2105, 2106, 2107 have a simple installation principle that does not require any modification from the driver. The whole procedure will only take a few minutes!
Another important advantage is the high quality of the mirror - the surface is resistant to cracks and scratches. Such damage not only spoils the appearance of the car, but also impairs visibility.
Lada 2106 #Bun Stage 1 › Logbook › Side mirrors Polytech T-7g
Hi all! I'll be brief today. Winter, late evening, -14 degrees outside, it’s time to wrap yourself in something warm, watch some good old movie, and put on the side mirrors you bought last week!
I won’t describe the process itself, it’s too simple - I unscrewed the old mirrors, the corner from the VAZ 2105/07 is no longer needed, because these mirrors have a built-in one, then you need to unscrew 3 screws from the new mirrors, disassemble them into 2 parts, insert a new corner into the door, attach the mirror body to it from the outside, and screw the screws into place from the interior, nothing complicated, it holds more than well.
A few more photos taken the very next day, during the day
View from the salon, and, in fact, a review of them:
And finally, after traveling with them for several days, I can leave the following, subjective review about them:
PROS:
— The best visibility of all the options suitable for classics — Modern look — Doesn’t rattle when driving — Folds up — There are many modifications to choose from, including electrical adjustment, built-in turn signals and heated mirror elements.
That seems to be all, but what else do you need for mirrors?
And now the CONS:
No matter how good it is, there is always a fly in the ointment... - The left mirror gets a little out of alignment when driving on our roads, it’s not critical, but for this money I have every right to demand that it stay rooted to the spot! Judging by the fact that the right mirror clearly maintains the specified settings, I conclude that this drawback is not universal, i.e. I just came across a bad copy of the left mirror... - The cables squeak unpleasantly when adjusting the mirror - Well, the price is too expensive
That's all for today! Thank you for watching)
source
How to disassemble the standard mirror of a VAZ 2106
To disassemble the standard “six” mirror, no special skills are required, and all you need is a thin flat-blade screwdriver.
- The mirror is removed from the hinge. This is done manually. The mirror must be taken by the frame and pulled with force in a direction strictly perpendicular to the car body. The hinge will disengage and the mirror will be released.
- The tip of a flat screwdriver is inserted under the plastic edging of the mirror (it is best to do this from an angle). The screwdriver is then moved around the perimeter of the mirror until all of the trim has been removed.
- After this, the back wall of the mirror is separated from the mirror element. No additional fasteners are provided in the standard mirror.
- Reassembling the mirror is done in the reverse order.
Download
Published August 30, 2016
Comments and place of residence copyright holder production LLC TVpro Media Test drive VAZ 21047 was filmed in 2009. VAZ-2104 is a Soviet and then Russian rear-wheel drive passenger car with a station wagon body. It is the brainchild of the Volzhsky Automobile Plant. Produced from 1984 to 2012. Subscribe to our channel and receive the latest news, test drives and first-hand car reviews!
Sources
- https://damage.shop-antistress.ru/vaz-2107-knigi-skachat.html
- https://videoremont-mashin.ru/remont-kuzova-vaz-21079/test-drayv-vaz-21047/
Top stunned View all
Mirrors VAZ 2101, 2102, 2104, 2105, 2107
Auto parts and accessories » Auto parts
Guaranteed to withdraw the goods, or the money back to the card. More details.
400 UAH
Krivy Rig, Zhovtnevyy Yesterday 18:49
Selling car VAZ 2107
Passenger cars » VAZ
28,527 UAH.
Side mirrors VAZ 2107,2105,2104,2109,2108,21099, tuning, VAZ mirror.
Auto parts and accessories » Auto parts
Guaranteed to withdraw the goods, or the money back to the card. More details.
450 UAH
Zaporizhzhya, Shevchenkivskyi 10 ber.
Side mirrors VAZ 2104,2105,2107,2108,2109,21099,2115
Auto parts and accessories » Auto accessories
Guaranteed to withdraw the goods, or the money back to the card. More details.
430 UAH
Removing the “dead zone” in mirrors
Small self-adhesive spherical mirrors are sold for tuning mirrors. Their range is quite large, so the shape and size of such mirrors can be selected individually.
The field of view of spherical mirrors is much wider than that of standard ones. Thus, the problem of “dead zones” is finally solved.
To install heated rear view mirrors, use self-adhesive heating film, which is sold in stores. You will need a screwdriver, a plastic ruler, double-sided tape and heating film.
To modify the mirrors, you need to remove them from the car. Installation of electric heating is carried out as follows:
Heated mirrors are ready. All that remains is to connect the wires to the car's electrical network.
Rear-view mirrors are necessary for the driver to control the traffic situation when performing various maneuvers to change lanes from one lane of the roadway to another, as well as for the convenience of reversing maneuvers. For the convenience of the driver, the design of the cars provides for the presence of rear side mirrors located on the front doors and one internal mirror located in the car interior, centrally located near the windshield.
Replacing the external side mirrors of the VAZ 2107. For repairs you will need a Phillips screwdriver.
- Open the door and lower the side window all the way. Find the mirror mounting screw and unscrew it.
- After unscrewing the screw, remove the side window seal and remove the mirror mechanism.
This completes the removal process. Remove the mirror on the other side in the same way. Install in the reverse order of removal.
Removing and repairing the internal rear view mirror of a VAZ 2107. The mirror, as already mentioned, is located in the car interior on a decorative trim in the upper part of the front windshield. The mirror is also attached using two self-tapping screws, which are hidden using a decorative overlay. Use a flathead screwdriver to pry up the cover and remove it. Next, use a screwdriver to unscrew the two fastening screws and remove the mirror itself. Installation is carried out in the same order as the reverse of removal.
At this point, the repair to replace the external side and internal mirrors of the VAZ 2107 is completed.
Rear-view mirrors are necessary for the driver to control the traffic situation when performing various maneuvers to change lanes from one lane of the roadway to another, as well as for the convenience of reversing maneuvers. For the convenience of the driver, the design of the cars provides for the presence of rear side mirrors located on the front doors and one internal mirror located in the car interior, centrally located near the windshield. Replacement of external side mirrors of VAZ 2107.
This completes the removal process. Remove the mirror on the other side in the same way. Install in the reverse order of removal. Removing and repairing the internal rear view mirror of a VAZ 2107. The mirror, as already mentioned, is located in the car interior on a decorative trim in the upper part of the front windshield.
Welcome! Today we will be replacing the side rear view mirror on VAZ 2108, VAZ 2109, VAZ 21099. Note! The article only describes replacing the side mirror itself with a new one, if you do not need to completely change the side mirror, but only need to replace the mirror part of the side mirror, then in this case (see How much will it cost to replace the side rear view mirror on a VAZ 2108-VAZ 21099? 1) A new standard side rear view mirror will cost you about 550-1200 rubles.
Important! 1) Install the new side mirror on the car carefully, do not damage it! For newbies! Question: What does the standard side rear view mirror look like, which was installed from the factory on VAZ 2108-VAZ 21099 cars? 1. We prepare the VAZ 2107 car for operations (see
Preparing a VAZ 2107 car for maintenance and repair).
Remove the outside rear view mirror. Installing an exterior rear view mirror on a VAZ 2107. Installing a mirror on a VAZ 2107 is performed in the reverse order. Zvyato from: https://vaz2107club. Ru. Taken from: https://dtp-online-news.ru.
Removing and installing a mirror on a VAZ 2107
Before you change the side mirrors on the VAZ 2107, let’s figure out what their purpose is. Side mirrors have a simple, but very important purpose - to control the traffic situation behind the car. They enable the driver to control the situation when changing lanes, overtaking, and reversing.
From the factory, the seven is equipped with conventional ZZV rear-view mirrors, which have many disadvantages:
- There is a small viewing area, but also many blind spots, which reduces visibility and also increases danger.
- Lack of heating leads to the fact that in cold weather the devices freeze, and therefore visibility is reduced.
- The appearance of the device is not modern, so it is impossible to do without upgrading the mirrors.
This is interesting! The first "sevens" came off the assembly line with one side mirror, which was located on the driver's door. However, later a second mirror appeared, and the reason for its appearance was the increase in the number of cars on the roads.
To install new CBs, you will need to dismantle the standard ones, which does not present any difficulties. To remove standard devices, you will only need to use a slotted screwdriver. The withdrawal algorithm is as follows:
- The washer that secures the adjusting lever is unscrewed by hand.
- Unscrew one screw that secures the decorative trim.
- After unscrewing, you can remove the cover.
- Under the lining there is a rubber gasket, which also needs to be removed.
- Now, to unscrew the device, you will need to unscrew the one remaining screw, just be careful so that the mirror does not fall to the ground.
- After dismantling, you can begin installing new mirrors.
