How to replace PTF lamps on a Lada Largus with your own hands

January 18, 2016 Lada.Online 109 917 1

During operation of the vehicle, the headlight bulbs may burn out. If you decide to replace them not at the dealer, but yourself, we recommend that you first study the instructions. The fact is that on the Lada Largus the lamps in the headlights change with some features, which we will discuss later.

You can replace faulty lamps yourself using the methods described below. If replacement seems difficult, it is recommended to contact a LADA dealer.

WARNING!

  • Before replacing a lamp, ensure that the associated signal light is turned off.
  • Wear protective gloves when replacing lamps.
  • Do not touch the glass bulb of the lamp with your bare hands. Hold it by the plinth.
  • Halogen lamps are under pressure and may explode when replaced. This may cause injury.

ATTENTION!

  • For normal operation of the lighting and light signaling systems, use lamps recommended by the factory.
  • Failure to comply with these recommendations may lead to destruction in the form of cracking or melting of the diffuser due to its overheating.

How to replace a PTF lamp on a Lada Largus

How to change the low beam light bulb on a Chevrolet Niva: which one is needed Left side:
You need to unscrew 3 screws and pull out one clip securing the lower apron

Next, without removing the large piston, carefully turn the apron to the side

Now we can easily reach the lamp. Turn it half a turn counterclockwise, remove it and install a new one.

Right side:

Here you also need to unscrew 3 screws and pull out 2 clips

Pull out the large piston, carefully move the shield to the side and replace the lamp

Reassemble everything in reverse order. Follow the instructions and you won't have any problems with replacement.

To adjust the PTF on Largus, a special screw was provided. Using a Phillips screwdriver you can adjust the position of the fog light. The adjustment hole is located on the PTF mask.

1 — headlight lamp; 2 - adjusting screw

Replacing the lamp

We carry out the work on an inspection ditch or overpass. Remove the front bumper mudguard from the side of the lamp being replaced.

Using a screwdriver, press out the plastic retainer of the wire block...

...and disconnect the block from the lamp.

Turn the lamp counterclockwise...

...and remove it from the headlight housing.

We install the new H11 lamp in the reverse order.

Removing, installing and adjusting the fog lamp

We remove the fog lamp for replacement. We carry out the work on an inspection ditch or overpass. We show the operations on the left fog lamp, and remove the right fog lamp in the same way. Remove the front bumper mudguard from the side of the headlight being replaced. Disconnect the wire block from the fog lamp lamp.

Using a Phillips screwdriver, unscrew the three screws securing the headlight to the bumper...

...and remove the headlight. Install the fog lamp in the reverse order. After installing the headlight, we adjust the direction of the light beam in the vertical plane. Through the hole in the front bumper...

...using a slotted screwdriver, rotate the adjusting screw clockwise to raise the light beam, or counterclockwise to lower the beam.

Repair of Largus - Replacing the H4 lamp in the headlights on a LADA Largus (practice)

Replacing the side light bulb of the headlight of Lada Largus

Fog lights Lada Largus, Granta, Kalina 2

Angel eyes in fog lights on Lada Largus

Replacing the fog light

As you can see, located on the left side of the engine. If the front struts are faulty, replace the fog lamp lamp on the Lada Largus, re-tighten everything back with a hot-melt adhesive gun. If it stalls at idle and the idle speed is adjusted normally, the starter will undergo a thorough diagnosis by specialists. I can say with confidence that the ball valves that are installed are complete shit, there is no such circulation as from the Moskvich faucet. Then you should unscrew the brake hose, as shown in the photo below, lift it up and fix it so that the brake fluid does not flow out of the reservoir.

Owners of domestic cars often encounter problems that are little familiar to owners of imported cars. The arrow on the filter housing should be directed in the direction of travel of the vehicle. Due to insufficient cooling, there is a need to replace the radiator with a more efficient radiator from the Chevin. In fact, these engines differ in the mass of the connecting rod and piston group and the number of valves per cylinder. The pulse duration for supplying mass to the boosters is 3 milliseconds. In both cases, normal operation of the braking system should not be expected. Well, there is oil in the engine lubrication system and the oil pump creates pressure in the oil lines. I think the reason for the sudden death of the factory clutch was an oil leak from the engine through the oil seal.

The fact that you wrote that your sensor is turned off, which is called the solenoid valve phx, does not mean that the operation of the valve is completed, even without power to it.

Sources

  • https://remontautomobilya.ru/zamena-lampy-ptf-lada-largus.html
  • https://carpedia.club/view/7905
  • https://avtolars.ru/lada-largus/v43005-zamena-lampi-protivotumannoy-fari-lada-largus.php

Instructions for replacing lamps

To replace, we will need a Torx T-20 sprocket wrench, with which we need to unscrew the self-tapping screws securing the fender liner.

Unscrew the screws securing the fender liner and bend the fender liner

A fog light with a lamp is visible in front of us. Press the latch and remove the block from the lamp.

Turn the lamp half a turn and remove it from the PTF. We install the new lamp without touching the bulb and connect the block to the lamp.

If after replacing the lamp it does not work, the problem may be in the wiring or fuse. Each PTF has its own fuse, so we recommend checking it first.

The fog light fuse on the Lada Largus is located in the mounting block under the hood. Fuse number F31.

Replacing lamps in the lighting fixtures of any car is not particularly difficult and can be done by almost any car owner. To make sure of this, we will try to independently replace fog lamps in Largus.

PTF on Lada Largus

Fog lights or PTFs in a car act as additional light sources. They help the driver to better see the roadway in poor visibility conditions. In most models they are installed in the bumper mounting sockets, as well as under (above) it, which is much less common. This light source is housed in its own housing.

Features of fog lights on Largus

If we consider the Russian station wagon Lada Largus, then its PTFs have design differences depending on the period the modification is on the assembly line.

Some configurations (“Norma”) are not equipped with this lighting equipment, so before purchasing, the owner of a Lada Largus should look into the bumper and make sure that there are corresponding niches under the PTF. Usually they are closed with special plugs.

All versions of headlights on the market are initially equipped with light bulbs.

As an option, you can resort to installing xenon lighting equipment. Here we recommend that you consult in advance about the applicability of the xenon lamp to the headlight body, since their geometric features may not coincide.

We also note the possibility of installing LED lighting sources.

Selecting the best PTFs

Reviews from experienced owners will tell you which fog lights are best to purchase. Based on this information, we have compiled the most successful headlight options into a single rating:

Now we move on to considering two options for installing and replacing fog lights. The first case is a more competent approach and involves removing the bumper, and the second option indicates an operational replacement method without dismantling the body element.

Special lighting

The fog lamp in the car modification cannot be reached through the engine compartment. The driver of Largus will have to crawl under the car:

  • remove the screws,
  • remove the fender liner,
  • press the latch and separate the block from the lamp,
  • turn the burnt-out light bulb counterclockwise a third of a turn,
  • extract element
  • insert a new one into the cartridge,
  • Install the lock in reverse order.

Finally, the functional operation of the devices is checked. If the headlights dim or flicker, the contacts in the system are not secure enough. Causes of malfunction:

  • contamination of electrical wiring,
  • oxidation of contacts,
  • manufacturing defects.

To eliminate the last reason for incorrect lighting operation, it is important to pay attention to the reliability of the manufacturers whose products are purchased. For Largus, it is recommended to choose only original optics.

Replacing a light bulb on Largus is a simple and quick process. Each car owner is able to perform the work independently. To achieve results, it is important to choose quality products, as well as adhere to safety precautions and instructions. Installing a new fog light bulb poses some difficulty, but even this can be handled with due care.

Fog lights or PTFs in a car act as additional light sources. They help the driver to better see the roadway in poor visibility conditions. In most models they are installed in the bumper mounting sockets, as well as under (above) it, which is much less common. This light source is housed in its own housing.

How to install fog lights?

Before starting the procedure for installing a set of fog lights in the Lada Largus bumper, we carry out a number of preparatory manipulations related to preliminary checking the correct connection of the wires and the functionality of the products, and also stock up on the necessary tools, the set of which is very simple.

The installation procedure is simple, so we can safely proceed to its implementation.

We open the hood and de-energize the network by removing the terminals from the battery. Now you can remove the front bumper, which will allow you to correctly install and connect the fog lights, as well as secure the wiring. We unscrew the screws from below that hold this element to the body of the LADA Largus. We do the same with the bolts under the hood and the screws in the wheel arches

We pay special attention to the two bolts hidden in the corners of the bumper, since without their “surrender” it will not succumb to removal, because the wings will not “set it free”. To defeat these fastening components we will use a screwdriver. During manipulation, carefully move the fender liner so that it does not interfere with our actions

We remove the bumper carefully, pulling it straight forward (in the direction of travel). Next, having conveniently positioned the bodywork, we dismantle the plugs. On the inner surface of the bumper we unhook the fixing components, after which the plugs are easily removed. We place new PTFs in the bumper niches and begin to securely fasten them. This is done using screws with which we fasten the lighting devices to the body element. Now we lay the wiring along the inner cavity of the bumper and fix it with tape and clamps. We do this on both sides of the body element. We fasten the negative wires to the body, which acts as the “ground” of the Lada Largus car. We install the bumper and secure it with the specified list of fasteners, proceeding in the reverse order. Next, you will need to bring the end sections of the PTF wires into the engine compartment area. When laying, we also use fastening ties. We move into the cabin and select a place to attach the pre-purchased PTF power button. The button itself can be embedded into the desired area of ​​the panel, which will be more aesthetically pleasing compared to fixing it on the surface of the interior element. The ends of the wiring attached to the button terminals are directed to the mounting block with relays and fuses. Remembering the cable ends of the PTF, we also bring them to the area where the unit is located, which is located on the left side of the steering column. We act according to the instructions included with the optics kit. We carry out all switching manipulations, connecting the wires as indicated in the instruction diagram. Finally, we check the functionality of the new lighting devices and, if necessary, adjust the correct direction of the light beam.

2278-22-12 —03 (Copy)

...remove the lamp from the headlight housing. ...remove the lamp from the headlight housing.

...remove the lamp from the headlight housing.

We install the new H11 lamp in the fog lamp of the Lada Largus car in the reverse order.

[How to save on maintenance of Lada Largus] [Maintenance of Lada Largus at 15,000/45,000/75,000/105,000 km] [Maintenance of Lada Largus at 30 thousand km] [Maintenance of Lada Largus at 60 thousand km of run] [Maintenance of Lada Largus for 90 thousand km of run] [Maintenance of Lada Largus for 120 thousand km of run] [Independent maintenance - general recommendations] [Safety rules for self-carrying out maintenance] [Tools required for carrying out maintenance Lada Largus maintenance] [Lamps used in the Lada Largus car]

How to install fog lights?

How to change the low beam bulb on a Lada Largus Before starting the procedure for installing a set of fog lights in the Lada Largus bumper, we carry out a number of preparatory manipulations related to the preliminary check of the correct connection of the wires and the functionality of the products, and also stock up on the necessary tools, the set of which is very simple.

The installation procedure is simple, so we can safely proceed to its implementation.

We open the hood and de-energize the network by removing the terminals from the battery. Now you can remove the front bumper, which will allow you to correctly install and connect the fog lights, as well as secure the wiring. We unscrew the screws from below that hold this element to the body of the LADA Largus. We do the same with the bolts under the hood and the screws in the wheel arches

We pay special attention to the two bolts hidden in the corners of the bumper, since without their “surrender” it will not succumb to removal, because the wings will not “set it free”. To defeat these fastening components we will use a screwdriver. During manipulation, carefully move the fender liner so that it does not interfere with our actions

We remove the bumper carefully, pulling it straight forward (in the direction of travel). Next, having conveniently positioned the bodywork, we dismantle the plugs. On the inner surface of the bumper we unhook the fixing components, after which the plugs are easily removed. We place new PTFs in the bumper niches and begin to securely fasten them. This is done using screws with which we fasten the lighting devices to the body element. Now we lay the wiring along the inner cavity of the bumper and fix it with tape and clamps. We do this on both sides of the body element. We fasten the negative wires to the body, which acts as the “ground” of the Lada Largus car. We install the bumper and secure it with the specified list of fasteners, proceeding in the reverse order. Next, you will need to bring the end sections of the PTF wires into the engine compartment area. When laying, we also use fastening ties. We move into the cabin and select a place to attach the pre-purchased PTF power button. The button itself can be embedded into the desired area of ​​the panel, which will be more aesthetically pleasing compared to fixing it on the surface of the interior element. The ends of the wiring attached to the button terminals are directed to the mounting block with relays and fuses. Remembering the cable ends of the PTF, we also bring them to the area where the unit is located, which is located on the left side of the steering column. We act according to the instructions included with the optics kit. We carry out all switching manipulations, connecting the wires as indicated in the instruction diagram. Finally, we check the functionality of the new lighting devices and, if necessary, adjust the correct direction of the light beam

During the manipulation, we carefully move the fender liner so that it does not interfere with our actions. We remove the bumper carefully, pulling it straight forward (in the direction of travel). Next, having conveniently positioned the bodywork, we dismantle the plugs. On the inner surface of the bumper we unhook the fixing components, after which the plugs are easily removed. We place new PTFs in the bumper niches and begin to securely fasten them. This is done using screws with which we fasten the lighting devices to the body element. Now we lay the wiring along the inner cavity of the bumper and fix it with tape and clamps. We do this on both sides of the body element. We fasten the negative wires to the body, which acts as the “ground” of the Lada Largus car. We install the bumper and secure it with the specified list of fasteners, proceeding in the reverse order. Next, you will need to bring the end sections of the PTF wires into the engine compartment area. When laying, we also use fastening ties. We move into the cabin and select a place to attach the pre-purchased PTF power button. The button itself can be embedded into the desired area of ​​the panel, which will be more aesthetically pleasing compared to fixing it on the surface of the interior element. The ends of the wiring attached to the button terminals are directed to the mounting block with relays and fuses. Remembering the cable ends of the PTF, we also bring them to the area where the unit is located, which is located on the left side of the steering column. We act according to the instructions included with the optics kit. We carry out all switching manipulations, connecting the wires as indicated in the instruction diagram. Finally, we check the functionality of the new lighting devices and, if necessary, adjust the correct direction of the light beam.

Let's sum it up

PTFs are quite useful devices that help the driver move confidently in difficult weather conditions. As you can see, not all Lada Largus configurations initially have such lighting devices in their arsenal. For caring owners, this is not an obstacle, and they easily purchase and install PTF in their cars.

We examined two options for installing lighting equipment in LADA Largus and found that they are quite simple. If your station wagon does not yet have these useful products, then feel free to purchase them and install them, after which the bad weather will not be able to scare you.

Sources used:

  • https://lampaexpert.ru/avtomobilnye-lampy/neispravnosti/zamena-protivotumannyh-lamp-largus
  • https://dorpex.ru/kuzov/remont-kuzova/osobennosti-zamenyi-lampyi-na-lade-largus
  • https://zamenarenault.ru/largus/elektrika-i-tormoza/protivotumannye-fary-lada.html

How to replace PTF lamps on a Lada Largus with your own hands

Replacing lamps in the lighting fixtures of any car is not particularly difficult and can be done by almost any car owner. To make sure of this, we will try to independently replace fog lamps in Largus.

Lamp type

Before you begin this, albeit small, but still repair, you need to prepare. Of course, first of all you need to buy a new light source. What kind of lamp is in the fog lamp of the Lada Largus?

Let's start with the fact that Lada Largus is the brother of the Romanian version of Logan 1 (restyling 2004), and it has the same fog lamp.

Since the fog lamp is the same, the lamp it uses is the same as in Renault Logan 1 - halogen with an H11 socket. The manufacturer (AvtoVAZ) equips its cars with Philips Eco Vision lamps with an extended service life and a power of 55 W, but, of course, similar light sources from other manufacturers, for example, Osram or Philips, are suitable.

Original fog light bulb Lada Largus

Lamp replacement process

How to replace a PTF light bulb? This process in Lada Largus is quite simple, although it requires some disassembly of the car. Therefore, in addition to light bulbs, you need to stock up on:

  1. Torx key 20.
  2. A 17-gauge spray gun (optional, but it makes the job easier).
  3. Cotton gloves or clean cotton cloth.

To get to the fog lights, you need to remove the fender liners. For greater convenience, I would recommend removing the wheel: it won’t take much time, but it will be much more convenient to work with.

The removed wheel in the Lada Largus greatly simplifies access to the fender liner

Now we arm ourselves with the T-20 key and unscrew the 4 screws securing the fender liner to the bumper and fender.

Partial dismantling of the fender liner on Largus

We bend the front part of the fender liner and get access to the Largus foglight.

Bent plastic fender liner

We disconnect the power supply from the fog lamp, for which we press the latch and simply pull out the block itself.

Removing the power supply from the Largus fog lamp

Take the fog light bulb by the socket and turn it counterclockwise a quarter turn. Now it can be removed. All that remains is to figure out how to replace the burnt out bulbs in the PTF with new ones.

Removed fog lamp

So, put on gloves, remove the new lamp from the box and install it in place of the burnt one, fixing it by turning it 45 degrees clockwise. We connect the power supply, making sure that the latch snaps into place. We install the fender liner, and then the wheel in place.

What to do if the fog lights still don't light up

It often happens that the reason for the failure of the fog light is not a burnt out lamp. What else could cause such a malfunction? There are few such options:

  1. A power surge in the on-board network that caused a fuse to blow. Typically this problem is caused by poor contact between the terminals of the battery, generator, or when turning on/off a powerful load. Eliminated by replacing the fog light fuse with a new one with the same rating.
  2. Oxidation of PTF power terminals and blocks. Identified by visual inspection. All power supplies are disconnected, the contacts are inspected and if there is any foreign deposits, they are cleaned.
  3. Short circuit. It may be caused by the insulation of the PTF supply wire rubbing against the body and shorting to it. In this case, as a rule, the fuse burns out, and replacing it with a new one leads to the same result. The malfunction can be eliminated by visual inspection of the wiring harness supplying the PTF, followed by isolating the damaged area.
  4. Broken power wire. Power wires can either break due to vibration or burn out when shorted to the body. In the latter case, the fuse usually blows. If the new fuse does not blow, but the fog light still does not light, you need to inspect the wiring harness, find and repair the break.

Where is the fog light fuse located?

The fuse through which the PTF on the Lada Largus is powered is located in the common fuse block. The unit itself is installed on the left side of the instrument panel and is closed with a protective cover.

We open the protective cover and get to the block, the numbering of the fuses in which is as follows:

Manufacturer's numbering of fuses in Lada Largus

Fuse F31 with a nominal value of 15 A is responsible for powering the fog lights and their relays.

So, we are convinced that it is quite possible to independently replace the light bulbs in the fog lights of the Lada Largus, and practically anyone can do this if they wish.

Lamps for fog lights - delivery of parts to VAZ

You can order Largus fog lamps from us with delivery in Moscow and the region. The PTF uses a lamp with an H11 12v 55w socket. Depending on the purpose, you can install lamps on Largus cars:

  1. Regular halogen.
  2. With increased light output.
  3. Under xenon.
  4. LED.

On Largus, the PTF is equipped with Philips Eco Vision lighting elements with an increased service life. It is possible to install Philips or Osram elements with increased light output; they will illuminate the roadway more efficiently. If a car owner wants to get the xenon effect, it is necessary to install electric lamps with a blue bulb, which will create a bright white light with a glow temperature of 4500-5000 K. To adapt foglights as an alternative to DRLs (this is real and quite possible), LED electric lamps should be installed. They will not be able to completely illuminate the road space, but as an alternative to running lights, they are what is needed. If you find it difficult to choose a product yourself, contact the professionals of our company. The specialist will place the order and, if possible, provide a discount.

Headlight malfunctions and how to fix them

There are not many items on the list of headlight headlight breakdowns. This is mainly due to damage to the lantern glass, failure of the corrector or the lamp itself. If the Lada Largus low beam lamp and corrector can be replaced, then the glass is installed only with the headlight assembly. Largus optics do not cause any inconvenience to owners. The most common problem is low beam bulbs burning out.

You can choose and install a good headlight bulb yourself. On the market of automobile spare parts and accessories there are light bulbs from both domestic and foreign manufacturers. Chinese lamps are not of very high quality: they burn out quickly and do not provide sufficient visibility on the road.

Standard halogen light should be yellowish. Many people prefer the so-called pseudo-xenon, which makes the glow white, but in bad weather conditions such lamps are inferior to standard ones. The latter sometimes even outperform LED and xenon optics, which produce a powerful luminous flux, but cost a lot of money and are installed in specialized centers. In fog and rain, halogen lamps demonstrate the highest penetrating ability of the light beam, which ensures their leading position.

Replacing lamps

The operation of replacing the lamp is simple and even beginners can do it. It is carried out as follows:

  • The negative terminal is disconnected from the battery.
  • A slight turn removes the plug from the back of the headlight.
  • The wire block is disconnected from the lamp.
  • The latch is removed from the grooves by pressing it with your finger.

The failed lamp is removed and a new one is installed in its place. It is recommended to use gloves when working, as fingerprints on the flask can lead to its premature burnout. The lamp is attached using a latch, a block with wires is connected to it, and a plug is put in place. A terminal is connected to the battery, then the operation of the headlight is checked.

It is recommended to change the bulbs in both headlights at once. This way you will be able to avoid the failure of another light bulb at the wrong time and ensure a uniform glow.

The problem due to which the Lada Largus headlight does not light may not be in the lamps. If replacing them does not bring any results, the fuse may have blown. The mounting block is located in the cabin at the bottom left of the steering column. Replacing fuses is a matter of seconds. Two fuses are responsible for the light. Even if they look intact, the cause of the malfunction may be hidden in poor contact. There is no special relay for headlights in Largus, and therefore the source of the problem may be oxidation of the contacts of the headlight itself.

There are often situations when the headlights do not work due to poor ground contact. In this case, inspection and cleaning of the contact is necessary. If this does not help, contact the service center specialists to identify the causes of the malfunction and eliminate them.

To replace the low/high beam bulbs, you do not need to dismantle the entire headlight or any of its parts, so the process does not take much time. If the headlights are shining, but the light beam is incorrect, the reason is a faulty corrector. Its main task is to lower or raise the luminous flux depending on the location of the car body. If the vehicle is loaded, then without adjustment by the corrector the light will blind oncoming traffic. This part cannot be repaired, which means it is immediately replaced with a new one. This will require disassembling the headlight unit.

Replacing a light bulb

Choice

First of all, it should be said that the low beam lamp for the Lada Largus uses a halogen H4 standard, i.e. contains two threads and is responsible not only for near, but also for distant lighting.

Currently on the market you can find such lamps from a variety of manufacturers, among which are the following:

  • Bosh;
  • Osram;
  • Philips;
  • Narva, etc.

In addition, domestic Mayak light bulbs have recently proven themselves to be quite good. Their advantages include not only low price, but good quality.

H4 standard lamp

Of course, when choosing lamps you need to pay attention not only to the brand, but also to the following characteristics of the lighting element:

CharacteristicsOptimal parameters
Brightness (light beam power)Up to 1550 lm
LifetimeUp to 1500 hours
Power45-60 W

Standard halogens provide an unnatural yellowish glow. However, recently light bulbs have appeared with a bluish glow. People call them pseudo-xenon.

In the photo - a pseudo-xenon bulb

However, it should be noted that such light illuminates the road well only in dry weather. In fog or rain, ordinary lamps are preferable.

Moreover, in bad weather, even the expensive “xenon” and “LEDs” are inferior to the latter, the power of the light beam is one and a half to two times more powerful than that of halogen bulbs. This is due to the fact that the light of these elements has insufficient penetrating power.

Thus, each driver can choose the most suitable light bulb, taking into account his own financial capabilities and the conditions in which the car will be operated.

Headlight plug

Replacement procedure

Replacing the low beam lamp on a Lada Largus is carried out in the following order:

  • Work should begin by disconnecting the terminal from the battery.
  • Then you need to remove the plug from the back of the headlight. To do this you need to turn it slightly.
  • After this, you should disconnect the block from the contacts by pulling it by the body.
  • Next, you need to remove the spring retainer from the grooves with your finger. After this, the bulb is easy to remove from the headlight, since nothing else holds it.

Spring retainer

  • Next, you need to install a new light bulb in place. It is better to do this work with gloves so as not to touch the glass flask with your own hands. The fact is that traces of fat can lead to rapid burnout of the lamp.
  • Then you need to fix the base with a spring clip, put the block on the contacts and then install the plug in place.
  • At the end of the work, you should connect the battery and check the operation of the headlights.

This completes the replacement of the low beam lamp in Largus. As we can see, this operation is carried out extremely simply.

Mounting block Largus

Where is the fog light fuse located?

The fuse through which the PTF on the Lada Largus is powered is located in the common fuse block. The unit itself is installed on the left side of the instrument panel and is closed with a protective cover.

Location of the fuse box in the Lada Largus (the protective cover has already been removed)

We open the protective cover and get to the block, the numbering of the fuses in which is as follows:

Manufacturer's numbering of fuses in Lada Largus

Fuse F31 with a nominal value of 15 A is responsible for powering the fog lights and their relays.

So, we are convinced that it is quite possible to independently replace the light bulbs in the fog lights of the Lada Largus, and practically anyone can do this if they wish.

During regular vehicle operation, the lamps in the daytime running lights and PTF headlights burn out faster than the lifespan declared by the manufacturer. Therefore, information on how to independently replace the lighting elements of optics is only useful for every driver. For clarity, let’s look at how to replace a low beam lamp on a Lada Largus.

  • optics type H4 with a power of 12 watts, 60/55W for near and far illumination,
  • PTF lamps with characteristics H11, 12 W, 55W,
  • for side lights, W5W models with a power of 5W are acceptable,
  • PY21W for turn signals.

Headlights.

I can drive up to you, look at my light, try it. If it suits you, I will recommend the lamps. Edited: 1 time (Last: January 22, 2013 at 15:56) Konstantin Kazanets St. Petersburg Rating: 881 08/24/2012 Club member Messages: 1202 Write a private message Lada Largus 7 seats 16V so they are regulated! So I ask - how? let's live - we'll see, we'll live - we'll find out, we'll survive - we'll take it into account.www.citilink.ru kutj066 St. Petersburg Rating: 3364 04/29/2012 Club member Messages: 3105 Write a private message Lada Largus 7 seats 16V Dmitry Amursky, thanks for the correction! I admit, I made a mistake... Not light temperature, but color temperature. Konstantin alex Gatchina Rating12 Messages: 2160 Write a private message Well, at least one more person has “seen the light” :)) PS: studying Physics and Chemistry, a little more than the school curriculum, is our EVERYTHING.

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]