How to attach a key fob to an Alligator alarm without ruining anything

Alligator alarm key fobs of various models and functions are configured in a special way, but only after binding to the control unit. Recording of remote controls in the memory of the anti-theft system is carried out according to one algorithm, using the “Valet” key. Up to four pagers can be programmed. If for some reason programming fails, you should immediately contact the service center. After all, more modern models of Alligator remotes require manual code entry. We will discuss in more detail how to attach a key fob to an Alligator alarm later.

We also have a Tomahawk 9020 instruction manual.

Programming key fobs D, M, S series

Alarm systems D, M, S series provide the ability to program up to 4 key fobs. In this case, it is allowed to use only two five-button and a similar number of four-key. When binding key fobs, the memory is overwritten, so previously flashed transmitters are deleted.

Sequence of actions for entering key fobs into the memory of the processor module:

1. Disarm the car.
2. Get behind the wheel of a car.
3. If the uncoded emergency shutdown mode of the car alarm is selected, you should press the Valet button three times within 15 seconds after turning off the ignition.
4. Wait for one short siren signal. The indicator light should start flashing slowly. These actions of the security system indicate readiness for programming a new key fob.
5. Press the key briefly. In the case of a D series alarm, you must hold down the button for a long time.
6. A long siren signal will inform you that the key fob programming has been completed.
7. The remaining transmitters must be linked in the same way.
8. Wait 15 seconds without operating the key fob or turn off the ignition.
9. Wait for one long and one short beep from the security system. Programming mode is deactivated.

If you use a personal code to disable the system, you must additionally perform the following steps to enter the programming mode:

1. Turn the ignition on and off.
2. Within 15 seconds, press the “Valet” button the number of times that corresponds to the first digit of the code.
3. Turn the car ignition on and off.
4. Enter the second digit of the code in the same way.
5. Switch the ignition again.
6. Continue programming the transmitter, similar to the algorithm with the uncoded emergency shutdown mode of the car alarm.

Alarm setup

The instructions for use indicate in detail how to install this anti-theft system, as well as make settings. Before starting work, it is better to read everything carefully and then act.

The first thing that the instructions for using the alligator autostart contains is recommendations on how to turn on the alarm. After installing it, you need to insert the key into the ignition of the car and begin manipulating the service button. It must be held for 3 seconds. After this, after a short time, press it three times. The alarm adapts to the car and gives a short signal.

When a short signal occurs, further setup occurs, which involves pressing all the key fob buttons one by one. The system completely reads the information it needs and is configured for the car. Then you need to turn off the ignition.

Now we need to tell you how the anti-theft system unit is configured if it reacts to the slightest noise. You need to study it carefully and find the cable going to it, consisting of 4 wires. They lead to all sensors that react to shock and opening. The instructions will describe in detail what to do to reduce sensitivity. A correctly configured unit will no longer bother the driver over trifles.

Alligator car alarms appeared on our market a long time ago. They are in demand due to a large range of useful security functions, ease of settings, as well as the presence of all kinds of protection against reading the signal between the unit and the key fob.

L Series Binding Features

It is possible to program the key fob in the L series security system as follows:

1. Disarm the car.
2. Sit in the driver's seat.
3. Turn on the ignition.
4. Move the “Jack” switch three times from the off position to the on position.
5. Wait for one siren signal. The indicator will flash once. The programming mode will turn on, allowing you to configure the control of Channel 1.
6. Press button 1 or 2 on the key fob. The selected key will control the first channel.
7. A long alarm signal will confirm that the alligator key fob has been successfully registered.
8. Change the position of the Valet switch once.
9. Wait for a long beep.
10. Check that the indicator flashes twice.
11. Start programming the second channel.
12. Press and hold the remaining unregistered button.
13. Wait for a long sound of the siren.
14. Wait 15 seconds. You can speed up the deactivation of the programming mode by turning off the ignition or double changing the position of the “Valet” switch

When binding the Alligator alarm key fob, regardless of the series, it is important to complete each action within a 15-second interval.

Otherwise, the programming mode is automatically deactivated. To reflash the key fobs, in this case, you need to start all over again.

Subscribe so you don't miss anything important

Content

We also have a Tomahawk 9020 instruction manual.

How to set up an alarm

At the final stage, the question arises of how to configure the Alligator alarm key fob. Before pairing your device, do the following:

1. Remove the original packaging from the device.
2. Open the battery compartment.
3. Make sure that the remote control is in an area of ​​stable visibility. Please note that the display has at least two bars indicating good connection quality.

After tying, you can turn on the Alligator alarm key fob and check the operation of all systems. To do this, open/close the car, turn on auto start, set it to alarm, check Panic mode and other available options. If necessary, configure the autorun option. For this:

• Press and hold the snowflake button F until a beep appears.

• To program a timer start, use buttons 1 and 2 to select the desired dial icon.
• Click F again, and then use buttons 1 and 2 to set the desired timer time.
• Set up engine autostart based on temperature. To do this, point at the images with a thermometer using buttons 1 and 2 and confirm the action by pressing F. Using the same principle, you can program the temperature parameters. And if necessary, you can remove the timer.

Knowing how to bind, configure and turn on the Alligator alarm, you can easily configure the security system key fob and avoid errors in its operation. In the comments, share your programming experience and the difficulties you encountered.

Instructions for setting up key fobs M, D, S series

Sequencing.

1. Disarm the vehicle.
2. Within fifteen seconds after deactivating the ignition, press the “Valet” key three times (non-coded mode is selected).
3. The siren will sound once. The LED will flash quickly. The control unit is ready to record remote control codes.
4. Briefly press the F button on the communicator. D series transmitter – hold F for a while.
5. A long siren signal will follow – programming has been successfully completed.
6. Use the same principle to register the rest of the keychains.
7. Do nothing for fifteen seconds or remove the keys.
8. Wait for one long and short siren signal. You have left programming mode.

If you use a system shutdown using a secret code, follow these additional steps.

1. Switch the ignition “On” - “Off”.
2. Complete this step in fifteen seconds. Click “Valet”, the number of clicks is the first value of the service code.
3. Click the ignition “On” - “Off”.
4. Also enter the second number of the password.
5. Crank the ignition.
6. Perform transmitter programming.

Types and models of Alligator alarm key fobs

General characteristics of Alligator keychains:

• The battery in the main remote control is used at 1.5 volts, in the additional one - 3;
• the main key fobs have a button blocking function from accidental pressing;
• signal transmission frequency 433-868 MHz;
• car search;
• panic mode - siren and alarm signals are activated;
• option to call the car owner from the salon;
• Anti-Hijack - protection function against robbery;
• Valet mode to disable all security functions of the anti-theft system.

Table of models of Alligator security system control panels and their main characteristics

How to register remote controls for Alligator L models

The Alligator L pager, which has 4 buttons, can be linked as follows.

1. Disarm the car. Turn on the ignition.
2. Press the Jack key three times. The siren will sound once and the LED will light up once. The control unit is ready to record a new control panel for channel 1.
3. Press key 1 or 2 on the remote control to tune to channel 1. A long siren signal will sound, indicating that programming is complete.
4. Turn on the "Jack" button once.
5. One sound will follow and the LED will light up twice. Channel 2 will be programmed.
6. Press the remaining button on the communicator (if you used key 1 or 2, you cannot press it again). The siren will emit a long signal - channel 2 programming is completed.
7. To exit the recording mode, turn on the ignition or press “Valet” twice.
8. The siren will sound for a long time.

We also have an instruction manual for the Tomahawk TZ 9020.

Technical characteristics, negative aspects

The alligator car alarm is characterized by the fact that it has many protective functions, therefore it occupies a leading place among our motorists and is installed on various cars. Its many models are equipped with great functionality, but have common technical characteristics.

• secure communication channels, the key fob for the alligator alarm and the alarm unit have special protection from various reading devices, which does not allow attackers to use special devices to unlock the alligator security system;
• increased signal reception range, the alligator car alarm has a range of 3 kilometers, this distinguishes it from models such as tomahawk and other security systems, this function is suitable for drivers whose cars are located far from them;
• individual encryption keys, control unit, and key fobs are encoded individually for each driver;
• short response time, this feedback security system provides a response to unauthorized entry or other actions with the car equal to ¼ second;
• starting the power unit, car alarm with auto start alligator, provides the ability for the car owner to turn on the engine without being in the car, or set their own modes, the ability to start at a certain frequency set by the driver, which allows it to be used on cars operated in the northern regions;
• installation and coding at home, all car alarm connections can be made at home, since it comes with the necessary connection diagram and detailed operating instructions, compiled in our language, setting up channels and other functions is carried out directly with the key fob and special buttons.

Reviews from motorists who preferred this security system indicate that it works effectively even in the most extreme conditions.

If we talk about the negative sides of this alarm, then there are practically none, with the exception of two points.

If the batteries in the key fob run out, then the driver loses contact with his car, and cannot remove and set the car alarm. When this happens, you need to immediately replace the batteries. But how to turn off the alligator alarm, since it will constantly go off.

To do this, you need to sit in the car and press a special button, which should be in an accessible place for the car enthusiast, but hidden from unauthorized persons.

There are situations when the alligator alarm system reacts to the slightest touch, vibration, noise (thunder, explosion of firecrackers). The user manual that comes with the kit provides for its reprogramming.

Reprogramming and flashing

It happens that the key fob freezes and refuses to carry out your commands. As a solution, you need to reset the settings and restore the firmware. Or you can program a second, spare remote control. In order to properly reflash the transmitter, do this.

1. Press the “Jack” service key once. The ignition must be turned off.
2. After that, click “Valet” three more times. The siren will sound.
3. Click the buttons on the pager one by one, synchronizing them with the control unit.
4. Turn the ignition on and off immediately. Check the functionality of the key fobs.

Open loop switch replacement

The binding of a transmitter with one-way communication is carried out according to the following scheme.

1. Disarm the car.
2. Turn off the ignition. Press the "Jack" key once.
3. Click “Valet” three times, the system will beep.
4. Press the switch keys one by one, synchronizing them with the alarm control unit.
5. Turn the ignition on and then turn it off. Check the operation of the switches.

How to enable engine autostart using the Alligator remote control

The Alligator alarm kit includes two remote controls: a five-button and a four-button. The engine can be started from either a 5-button or 4-button key fob. To do this, you need to know the sequence of keystrokes.

The Alligator anti-theft system allows you to independently set the auto start of the car based on temperature, control the warm-up time, and adjust the time for automatic engine start and stop.

1. Enter service mode by holding the F key for two seconds on the main pager. The screen will turn on and a beep will sound.
2. Press F again, the display will show “timer”. CHIRP will follow.
3. Select the desired time period in hours (1-2-3-4-6-24). Each press will be accompanied by a squeak and the turn signals will activate.
4. Select temperature trigger mode. The “tempo” symbol will appear on the screen. The key fob will emit a melody and the turn signals will blink. Select the desired autostart temperature (-10, -15, -20, -25). To exit, press the F key for two seconds. After exiting, the symbols of the selected functions are activated on the display.
5. To disable autorun, reset the values ​​in the menu.

We also have instructions on how to use the Tomahawk 9020 key fob on our website.

How to determine the alarm model by key fob

The manufacturer's alarm model Alligator can be determined by the description of the appearance of its key fob:

1. TD-350/355. Remote controls in this series have a vertical screen orientation. The device is equipped with a non-removable antenna, which is part of the housing. The keychain is made in silver with black edging.
2. D-910. The communicator has a small screen, the area of ​​which does not exceed 1/3 of the front panel of the key fob. The device has a removable black plastic antenna and a body with round silver inserts.
3. S-800/825/850/875. The key fob features a horizontal screen orientation with a white backlight. The body is made of dark gray plastic and equipped with a built-in antenna. This security system, unlike others, has the function of auto-starting the engine based on voltage, so the display has a characteristic icon in the form of a lightning bolt.
4. TD-320. The device has a black body with a thin silver insert around the display and an enlarged eyelet for attaching to a keychain. The remote control screen has a vertical orientation and is distinguished by a large lock icon in the middle.

Photo gallery: Alligator security systems

Photos of alarms with feedback from the Alligator company.

Connecting a new car alarm pager with feedback

Synchronization of the control panel of the Alligator anti-theft system is performed according to the following algorithm.

1. Turn off security mode. Turn on the ignition.
2. During the allotted period of time (fifteen seconds), turn on “Jack” three times. The system will emit three siren sounds and the LED will flash slowly.
3. Click the “closed lock” button on the remote control. A long CHIRP will follow. The transmitter will make one sound.
4. Repeat the previous step for the remaining key fobs.
5. Exit recording mode by turning off the ignition or doing nothing for fifteen seconds. You will hear a short and long siren signal.

Buy key fobs for alarm Alligator

Cost of control panels for the Alligator security system of various models:

Programmable functions for your alarm

Alligator allows you to program the following features:

• service: automatic door locking based on a tachometer signal or when the ignition is turned on, unlocking the car based on tachometer readings, protection against false alarms, etc.;
• security functions: activation of protection with or without locking doors, passive engine blocking, activation of Anti-HiJack mode and more;
• Remote engine start: starting the car based on temperature, time. Special mode for turbocharged cars and more.

Why is the Alligator key fob not programmable?

The remote control for the Alligator alarm system broke down, and you decided to flash a new one. But I can't unlock the transmitter. Why can this happen with key fobs (TD 350, M2200, D 910, 975, S850RS, M 2200, S 875rs, S 200, M800, S400) and how to fix it?

1. Pager failure. Repair it yourself or replace it with a new one.
2. The “Ignition on” command is not detected by the control unit. Contact the specialists.
3. Jack mode was accidentally activated. Turn off and repeat the procedure for writing switches.
4. Damage to the control unit. Contact the service center.

Why program remote controls?

The question of how to bind and how to set up an Alligator alarm may arise in the following cases:

• Broken old remote control.
• Lost key fob.
• The appearance of an additional driver who needs an individual control device.

Regardless of the goals, the binding occurs according to the algorithm discussed above.