We remove the front bumper on a Renault Logan with our own hands (photos, videos, articles)

Replacing or repairing the Logan sedan bumper will not be difficult. You just need to remove this part correctly without damaging anything around it. On the body of many passenger cars, shields are installed under the bumper. Renault Logan also has them, and before removing the front bumper, you need to get rid of the shields. It would be better to drive the car itself into a pit - we are not considering other options.

The bumper is removed to install DRLs, install fog lights, or simply for repairs.

Sequence of dismantling work

Preparation

Some operations to remove the front buffer of the car will have to be performed from below, so for convenience it is better to drive the car onto a viewing hole, overpass or lift. Next, you should inspect the bottom and fender liners of the car, remove dirt so that it does not fall down your collar while doing work.

  1. Work should begin from the bottom of the car, that is, by unscrewing the screws that attach the underbody protection element to the bumper (instead of unscrewing three screws, you can pull out two clips, and then the protection will be removed along with the bumper). We perform a similar operation on the other side.
  2. The next step is to unscrew the bumper from the fender liner. To do this, take Torx T20 and unscrew two screws, near the left and right wheels.
  3. Having unscrewed the fender liner, move it slightly to the side, and we will notice the lower bumper mounting bolt. We take the head at “10” and unscrew the fastening bolt that holds the bumper on the car’s fender; we carry out the same procedure near the other wheel of the car. Having unscrewed the bolts, we remove the ends of the bumper from the engagement, slightly moving them to the side.
  4. In the lower front part, the bumper is secured with three screws with Torx T30 socket heads, unscrew them. By removing these screws we finish the work under the car's underbody.
  5. In the front part under the hood of the engine compartment there are four more Torx T30 screws; we remove them.
  6. Having finished unscrewing the last screw, we proceed to removing the bumper. Carefully grab the bumper by the ribs and, slightly pulling it towards you, dismantle it.
  7. If fog lights are installed on the front bumper of your Renault Logan, then before dismantling it, be sure to remember to disconnect them from the central electrical connector. Its location: in front of the left wheel in the lower part of the body.

Video tips for DIY dismantling

Removing the bumper from a Renault Logan car is very simple and takes about 25–30 minutes. Sometimes, to make it easier to unscrew screw joints, use WD-40, a special aerosol that corrodes rust and dirt at the joints.

Video tips for DIY dismantling

Removing the bumper from a Renault Logan car is very simple and takes about 25–30 minutes. Sometimes, to make it easier to unscrew screw joints, use WD-40, a special aerosol that corrodes rust and dirt at the joints.

Removing the rear and front bumpers of Renault Logan is one of the operations that is performed when repairing a vehicle. It is performed when troubleshooting a radiator, upgrading a car, or performing work related to the restoration or tuning of a body part. The car enthusiast can perform this action independently.

OUR REAL WORKS! "NOT DOLLS"!

The cost of the work was:

Front bumper (removal/installation) — RUB 1,500. Front bumper (repair) — RUB 2,000. Front bumper (painting) — RUB 6,500. Front right wing (repair) - 2,500 rubles. Front right fender (painting) - 6,500 rubles. Right windshield pillar (painted) — RUB 3,500. Car wash - 500 rub.

The price is indicated on a turnkey basis (labor + materials).

The cost of the work was:

Front bumper (replacement) — RUB 1,500. Front bumper (painting) — RUB 6,500. Front right fender (replacement) - 1,000 rubles. Front right fender (painting) - 6,000 rubles. Right wing mounting bracket (repair) - RUB 2,000. Right wing mounting bracket (painted) — RUB 1,250. Front panel (repair) - RUB 2,000. Front panel (painting) — RUB 1,250. Front fog lights (installation) — RUB 1,500. Car wash - 500 rub.

Front bumper (renault logan spare parts catalog)

CodeNumberSubstitutionsNameAdditional Information
16001549793FRONT BUMPER (RSet E1, E2
38200752803BUMPER GRILLE (R
48200785081HEADLIGHT BRACKET (PLWith fog lights
58200752827HEADLIGHT BRACKET (PLWith fog lights
67703008162BOLT M6Size (X) = 6
77703046134NUT M6
87703602206BOLT M6
97703008162BOLT M6Size (X) = 6
107703076118HOLDER RETAINERWith fog lights
116001549323BUMPER DEFLECTORogre series - SAN513
116001547950BUMPER DEFLECTORogre series - SAN513
126001547949BUMPER DEFLECTORogre series - SAN513
126001549324BUMPER DEFLECTORSeries - SAN513
13054000001R7703072360PISTON 8MM (PLUS)
147703077435SKIN MOUNTING PISTON
157703017090BOLT M8
188200752748RADIATOR GRILLE
198200838547BUMPER CAP RWith fog lights
208200838548BUMPER CAP RWith fog lights and
217703002838BOLT M6
227703072419RIVET D=4.8MM (

Currently reading: Tow bar for Renault Logan – buy at a great price in Moscow

Down with the shields

Remove the shield installed on the left. It is mounted on self-tapping screws, as well as on two pistons (see photo).

Find five fasteners

For self-tapping screws you need a Torx T20 key. You will also need a flathead screwdriver. It’s better to do the work from a hole, but craftsmen remove the bumper from the curb; Logan’s ground clearance allows you to get to the fastenings without a lift.

The spacer screw is unscrewed from the middle (central) piston, but not completely, but by 2-3 turns. The piston is pulled down by the head of the screw, and nothing else is required. The second piston, located on the edge, is pressed out with a screwdriver (see photo).

Screwdriver – between the shield and the body

The simplest thing left is to unscrew three self-tapping screws. Take a Torx wrench and you'll be fine.

Dealing with the fender liner from the edge of the bumper

Near the bumper on each fender liner there are two self-tapping screws. A Torx T20 key will help solve the problem. And then the most difficult thing begins - you will need to bend the fender liner!

Bend point

The idea is to place a “10” key in the upper corner of the bumper. This will be a socket wrench, and it is brought in from below. Next, unscrew the fastening screw.

Step-by-step instruction

1. First, you need to unscrew the fasteners from the bottom of the bumper.

Remove two clips (small and large) on the left and right.

To remove the small clip, use a flathead screwdriver to turn it counterclockwise about a quarter of a turn. Next, we pick out the central part with a spatula or a flat screwdriver, and then we pick it up at the base and take it out.

To remove the large clip, you just need to pick it up.

If you remove the clips, you will remove the bumper along with its protection. If you want to remove without protection, then unscrew three screws on the right and left.

2. Unscrew two screws securing the bumper to the fender liner on the right and left.

3. After unscrewing the screws securing the bumper to the fender liner, bend the liner and unscrew the bolt securing the bumper to the fender. We do this on the right and left.

4. Unscrew the three screws securing the bumper from the bottom center.

5. Open the hood and unscrew the four screws securing the bumper on the Renault Logan on the top bar.

6. We take hold of the grille and remove the bumper towards ourselves.

Attention, if you have PTF installed, then disconnect the power connector before removing the bumper. It is common to two PTFs and is located near the left wheel.

Video lesson

How to remove the front bumper

The process of removing a body part on a front-wheel drive Renault Logan is performed in the following sequence:

Remove the underbody protective element; it is integral with the front bumper. To dismantle you need to unscrew the screws. 3 on each side. An alternative option is to remove two fasteners. In this case, the protection is removed along with the body part. Separate the body kit from the fender liner. The procedure is performed with a flat screwdriver. The clips, clamps, bracket and pistons are pressed out one by one. Using a T20 Torx wrench, you need to unscrew two screws near the right and left wheels. After completing the previous step, the fender liner will need to be moved slightly to the side

This must be done carefully, as there is a high risk of cracks. After completing the operation, the lower mounting bolt of the body kit becomes noticeable

The head is “10”, it needs to be unscrewed. Similar actions are performed around the other wheel. After dismantling the fasteners, the ends of the element are removed from engagement by lightly moving to the side. Unscrew the three lower mounting screws that are located at the front, at the bottom of the car. The procedure is performed with a Torx T30 key. Now, in order to remove the front bumper from a Renault Logan car, you will need to remove four more fasteners. They are located directly under the hood of the vehicle and are unscrewed using Torx T30. The completion of the operation to replace the front bumper on a Renault Logan car is the removal of the body kit. To do this, you need to grab the edges of the element and pull it slightly towards you.

How to install body kit

Installation of the body kit located at the front is carried out in the reverse order of disassembly:

  • The element needs to be put in place. A slight click of the latches indicates correct installation.
  • Install the top screws that secure the part.
  • Tighten the bolts on the side of the fender liners. Secure the lower fastening.
  • Screw the fasteners into the lower front part of the car.
  • Install protection, provided that it has been dismantled.

We recommend: How to replace the air filter on a Renault Duster - we’ll write it down in order

Removing the rear bumper of Renault Logan 2

To replace the protective part on the rear of Renault Logan 2 you will need:

  • TORX keys T 20-30, No. 10,
  • flat screwdriver,
  • for pistons – plastic mounting blade.

Sequence of actions after removing the rear lights:

  1. Using a spatula, the pistons of the upper fastening of the protective panel are pryed up and removed from both sides of the car.
  2. Three bolts are removed from the upper mount.

  3. Three bolts are also unscrewed in the lower mount.
  4. The wheel mudguards are secured with two screws at the front and one at the rear; they can be unscrewed.
  5. The fender liner fasteners are unscrewed. The fender liner fasteners are unscrewed
  6. The ends of the part, despite the resistance of the holders, are disconnected and pulled back, after which the bumper can be removed.

  7. Install all components in reverse order.

Dismantling the lantern

To replace the rear light fixture in Renault Logan 2, you don't need any tools.

Algorithm of actions:

  1. The wire is removed from the battery (from the negative terminal).


    Disconnect the negative terminal

  2. The trunk lid opens.
  3. The wing bolt is removed from the mounting of the lamp and the body, after which the lighting device is moved away from the body as far as the wiring harness allows. To do this, you need to remove the retainer from the body hole.
  4. There is a body holder bracket on the light housing; it can be disconnected.
  5. The wiring harness block is disconnected from the flashlight; after pressing the latch, the flashlight can be removed. Disconnect the chip
  6. The new lighting fixture is installed in the reverse order.

Replacing the rear bumper

To remove the rear bumper from Renault Logan, you will need:

  1. Dismantle the light bulb that illuminates the license plate, mud flaps and rear wheel fenders.
  2. Unscrew the mounting bolt located at the rear in the left wheel arch. The operation is performed with a “10” head. Use a screwdriver to press out the pins.
  3. Pull the side part of the body element and disengage the latches.
  4. Remove the five mounting bolts from the bottom. The procedure is performed with a 10mm head.
  5. Open the trunk lid and use a T30 Torx key to unscrew the three top mounting screws.
  6. Carefully remove the body kit from the bracket. If it is damaged, it will subsequently be impossible to securely secure the rear bumper.

How to reinstall the rear bumper

To install the rear bumper, you will need to perform all operations in the reverse order of disassembly. However, the procedure has a number of nuances:

  • Before installation, you must thoroughly wash the “landing” area.
  • It is necessary to ensure that the clamps located on top fit exactly into the grooves intended for them. This rule also applies to other fasteners.
  • If after installation the body part sags, then the caps should be replaced. Bolts are used as a replacement. To do this, you will need to dismantle the bumper again and use pliers to squeeze out the unusable pistons.

There is nothing difficult about removing and installing bumpers on Renault Logan yourself. This part of the car body is held on by bolts, self-tapping screws, which can be easily unscrewed with keys. And also, plastic pistons, clamps and brackets, which can simply be pressed out with a flat screwdriver.

When performing the procedure, it is important to know the sequence of the operation and be especially careful. If fasteners break, the body part will not adhere tightly to the car, which will require additional time, effort and money.

Body parts for Renault Logan | Topic started by: Pluto

New colored bumpers, hoods, fenders for Renault Logan from a warehouse in St. Petersburg, delivery throughout Russia tel.

Natalya (Vidyagauri) Exclusive baseball caps from Renault and other brands for 690 rubles including delivery! Order here: goo.gl/eyhmaj

Alyona (Micha) Front bumpers available for Renault Logan-1 Phase 2 The bumper is designed for installation on Renault Logan 1 cars after restyling - Phase 2 - from 2009 to 2022.

The bumper is not original, made by injection molding from polypropylene-based plastic. Bumper production - Nizhny Novgorod, Russia.

The bumper is painted in the color of the new car using modern paints and varnishes and is completely ready for installation on the car.

There are no holes for installing fog lights. Towing hole plug included.

The warranty on paintwork is 6 months.

1. NV 676 Noir Nacre/ Black Pearl 2. OV 369 Blanc Glacier/ White Ice 3. TE 21B Rouge Toreador/ Red Toreador 4. TE CNA Gris Platine/ Gray Platinum 5. TE KNM Gris Basalte/ Light Basalt 6. TE RNF Blue Mineral/ Blue Mineral

Alyona (Micha) Front bumper Renault Logan-1/ Renault Logan-1 RESTYLING unpainted

The bumper is designed for installation on Renault Logan 1 after restyling - Phase 2.

The bumper is not original. Made by injection molding from polypropylene-based plastic.

The manufacturer of this bumper for Renault Logan is , Nizhny Novgorod, Russia.

Alyona (Micha) Front bumpers Renault Logan 1 / Renault Logan 1 full painted and with a stripe.

There are no holes for installing PTF.

The bumper is designed for installation on Renault Logan cars before restyling - Phase 1.

The bumper is not original. Made by injection molding from polypropylene-based plastic.

The manufacturer of this bumper for Renault Logan is Nizhnekamsk, Russia.

The bumper is painted in the color of a new car in an industrial environment in Tolyatti with high-quality modern paint coatings.

1. F98 Vert Opaline (silver opal metallic) 2. B66 Gris Eclipse Nacre (dark gray metallic) 3. 61G Albastru Egee (blue metallic) 4. 632 Gris Boreal (silver metallic)

The warranty on paintwork is 6 months.

Alyona (Micha) Renault Logan rear bumper unpainted

The bumper is designed for installation on Renault Logan cars before restyling - Phase 1.

The bumper is not original. Made by injection molding from polypropylene-based plastic.

The manufacturer of this bumper for Renault Logan is Nizhnekamsk.

Alyona (Micha) Rear bumper Renault Logan 1 / Renault Logan 1 painted in the color of the car.

The bumper is painted with a matte black stripe (black top) or completely painted.

The bumper is designed for installation on Renault Logan cars before restyling - Phase 1.

The bumper is not original. Made by injection molding from polypropylene-based plastic.

The manufacturer of this bumper for Renault Logan is Nizhnekamsk, Russia.

The bumper is painted in the color of a new car in an industrial environment in Togliatti with high-quality modern paint coatings. The warranty on paintwork is 6 months.

1. F98 Vert Opaline (silver opal metallic) 2. B66 Gris Eclipse Nacre (dark gray metallic) 3. 61G Albastru Egee (blue metallic) 4. 632 Gris Boreal (silver metallic)

Alyona (Micha) Renault Logan-1 front fenders painted in the color of the car.

We dismantle the front bumper

If the package includes PTF headlights, you need to turn them off (read more about replacing the lamp in PTF here)! There is only one connector used, and it is located above the left shield (which has been removed).

Headlights included in one plug

We disconnected the connector and then looked for the attachment points. In total there are 7 of them left.

Screws on the bumper

Taking the T30 key, unscrew the three screws from the bottom. They go “in one line” (see photo).

Seven attachment points

Then you can drive the car away from the pit and unscrew the screws on top. The same key is used (T30).

The part called “bumper” can be pulled towards you. At the same time, she is held by the bars of the grate.

We only pull behind bars

We looked at how to remove the front bumper on the first generation Renault Logan.

Second generation of the model (since 2009)

Let's see what the bumper looks like in the second generation. It is shown assembled with the radiator grille.

Single node

The bumper and grille form a single unit. The number of attachment points is 11:

  • 4 screws on top (see photo);
  • 3 screws from the bottom;
  • 2 self-tapping screws on the side edges at the bottom (fastening the fender liner);
  • 2 screws in the corners.

The assembly assembly is removed in the same way as the bumper in the first generation. Use the instructions for “generation 1”.

Here we discuss how to remove the front bumper of Renault Logan 2. There is also generation “3”.

How to diagnose the problem at an early stage?

In order to promptly determine the malfunction of the Renault drum and rear brake as a whole, you should contact a service station. Experienced specialists carry out a full range of activities to check drums at a special stand. In this case, the computer records the main parameters and provides results on the need to replace the part.

In normal operation, the problem is diagnosed by the appearance of brake fluid on the mechanism cylinder or by sharply pressing the brake (the road must be dry). The last test should be carried out 3-4 times. If the braking distance marks are even, then the brakes operate evenly.

To determine whether Renault drums need to be removed or not, check the condition of the working part and measure its diameter. So, if this parameter is more than 18.124 cm (for a 1.4-liter engine) or 20.445 cm (for a 1.6-liter engine), then the device requires replacement. In addition, the drum will have to be removed to install new pads, to check the brakes, or to adjust the system cylinders.

How to remove the front bumper on a Renault Logan: video and photos

Replacing or repairing the Logan sedan bumper will not be difficult. You just need to remove this part correctly without damaging anything around it. On the body of many passenger cars, shields are installed under the bumper. Renault Logan also has them, and before removing the front bumper, you need to get rid of the shields. It would be better to drive the car itself into a pit - we are not considering other options.

The bumper is removed to install DRLs, install fog lights, or simply for repairs.

Down with the shields

Remove the shield installed on the left. It is mounted on self-tapping screws, as well as on two pistons (see photo).

Find five fasteners

For self-tapping screws you need a Torx T20 key. You will also need a flathead screwdriver. It’s better to do the work from a hole, but craftsmen remove the bumper from the curb; Logan’s ground clearance allows you to get to the fastenings without a lift.

The spacer screw is unscrewed from the middle (central) piston, but not completely, but by 2-3 turns. The piston is pulled down by the head of the screw, and nothing else is required. The second piston, located on the edge, is pressed out with a screwdriver (see photo).

The simplest thing left is to unscrew three self-tapping screws. Take a Torx wrench and you'll be fine.

Dealing with the fender liner from the edge of the bumper

Near the bumper on each fender liner there are two self-tapping screws. A Torx T20 key will help solve the problem. And then the most difficult thing begins - you will need to bend the fender liner!

Bend point

The idea is to place a “10” key in the upper corner of the bumper. This will be a socket wrench, and it is brought in from below. Next, unscrew the fastening screw.

We dismantle the front bumper

If the package includes PTF headlights, you need to turn them off (read more about replacing the lamp in PTF here)! There is only one connector used, and it is located above the left shield (which has been removed).

Headlights included in one plug

We disconnected the connector and then looked for the attachment points. In total there are 7 of them left.

Screws on the bumper

Taking the T30 key, unscrew the three screws from the bottom. They go “in one line” (see photo).

Seven attachment points

Then you can drive the car away from the pit and unscrew the screws on top. The same key is used (T30).

The part called “bumper” can be pulled towards you. At the same time, she is held by the bars of the grate.

We only pull behind bars

We looked at how to remove the front bumper on the first generation Renault Logan.

Second generation of the model (since 2009)

Let's see what the bumper looks like in the second generation. It is shown assembled with the radiator grille.

Single node

The bumper and grille form a single unit. The number of attachment points is 11:

  • 4 screws on top (see photo);
  • 3 screws from the bottom;
  • 2 self-tapping screws on the side edges at the bottom (fastening the fender liner);
  • 2 screws in the corners.

The assembly assembly is removed in the same way as the bumper in the first generation. Use the instructions for “generation 1”.

Articles

Different components are suitable for machines of different generations:

  • 6001549907 or 6001551338 – generation 1 (until 2009), PTF plugs are installed;
  • 8200785044 – generation 2 with PTF;
  • 8200748275 – bumper for second generation cars without PTF.

In the first case, the plugs can be cut out. This is done if the configuration includes PTF.

Removing the grille without removing the bumper

If you remove the front bumper of the new Renault Logan, the radiator grill will also be removed. But getting rid of the bars can be easier.

Car without a grille, but with a bumper

We will talk about the second generation of cars. Need a drill:

Remove the chrome "saber". Along the edges under the “saber” there are rivets (aluminum). They must be bitten off with tongs;

The “saber” can be glued back

Unscrew the 4 screws on top;

Having folded the grille towards you, you need to drill out the rivet under the emblem; The lower edge of the grille is held on by rivet tongues (plastic). They bend by hand and are easily disengaged.

Use our method if you no longer need the old part.

Removing the grille without removing the bumper

If you remove the front bumper of the new Renault Logan, the radiator grill will also be removed. But getting rid of the bars can be easier.

Car without a grille, but with a bumper

We will talk about the second generation of cars. Need a drill:

    Remove the chrome "saber". Along the edges under the “saber” there are rivets (aluminum). They must be bitten off with tongs;

The “saber” can be glued back

  • Unscrew the 4 screws on top;
  • Having folded the grille towards you, you need to drill out the rivet under the emblem;
  • The lower edge of the grille is held on by rivet tongues (plastic). They bend by hand and are easily disengaged.
  • Use our method if you no longer need the old part.

Related Renault Articles

Arriving home, I looked at all the places where I had missed silicone. Nowhere where mud had previously appeared after even a little rain was clean.

Yesterday it rained in Tula for more than half a day. Bend the fender liner and use a 10mm socket wrench to unscrew one bolt on each side.

With a little effort, we disengage the bumper from the fender guides, and then move on to the next side. The final phase of work on the bottom will be unscrewing three bolts in the central part of the body, for this we use a Torx key - T. Having opened the hood on your Renault Logan, you will see 4 more bolts securing the front buffer from its upper part.

We unscrew these 4 bolts with a Torx key T. After carrying out the above operations, grab the hard places of the part and boldly pull it towards you. Dismantling can be considered complete. If your Renault Logan has fog lights, before removing the bumper you need to disconnect the electrical connector on the left side behind the fender liner.

This work takes about ten minutes, and any Renault owner, even those without experience, can do it

Rear element The rear bumper also provides important protection for the Renault Logan, since most accidents also occur there.

Dismantling the rear element

How to remove the rear bumper? The rear element also performs a similar protective function. Removing the rear bumper is carried out using a slightly different method and this will require a modified set of tools (compared to the above procedure).

Ball joint Renault Logan

  1. The first action will be to place the Renault Logan car on one of the suitable devices (lift, overpass or pit).
  2. Having located ourselves under the bottom, we clean all the bumper mounts, generously watering them with WD-40.
  3. On each side of the Renault Logan car we unscrew the bolts securing the plastic wheel arch liners. This way the rear bumper is removed.
  4. Having unscrewed the bolts and bent these plastic protective structures a little to the side, we find the fixing elements to the ends of the wings. We twist it mercilessly. By the way, this fastener saves you from sagging.
  5. Now we can pull the Renault Logan body element outward, which will free its sides from engaging with the body guides.
  6. The central section is fixed to the body with three bolts, which we also use the appropriate key.
  7. Disconnect the electrical connector for the rear license plate lamp.
  8. We open the luggage compartment lid and find 4 more bolts treacherously holding onto its upper surface.
  9. After unscrewing them, we begin to carefully pull them towards us until they are completely freed from the body.

As you can see, the procedure is not labor-intensive and can “steal” no more than half an hour of time from the owner of a Renault Logan.

Do-it-yourself replacement of front and rear bumpers on Renault Logan

The second generation of the model from the year Let's see what the bumper looks like in the second generation.

Logan pulling the front bumper amplifier 1st hour

They are located directly under the hood of the vehicle and are unscrewed using Torx T. Use our method if the old part is no longer needed. If after installation the body part sags, then the caps should be replaced.

Sequence of dismantling work Preparation Some operations to remove the front buffer of the car will have to be performed from below, so for convenience it is better to drive the car onto a viewing hole, overpass or lift. Preparing tools and devices To perform the operation, you will need a set of tools that every motorist has in the garage.

Also, the bumper is traditionally damaged when parking. This part of the car body is held on by bolts, self-tapping screws, which can be easily unscrewed with keys.

Self-tapping screws on the bumper Taking the T30 key, unscrew the three screws from the bottom. Seven attachment points Then you can drive the car away from the pit and unscrew the screws on top.

The second generation of the model from the year Let's see what the bumper looks like in the second generation.

Removing the front bumper on Renault Logan

The number of attachment points is equal to: The assembly assembly is removed in the same way as the bumper in the first generation. Here we discuss how to remove the front bumper of Renault Logan 2.

Articles Different components are suitable for machines of different generations: In the first case, the plugs can be cut out. This is done if the configuration includes PTF. Removing the grille without removing the bumper If you remove the front bumper of the new Renault Logan, the radiator grille will also be removed. But getting rid of the bars can be easier.

A car without a grille, but with a bumper. We will talk about the second generation of cars. They bend by hand and are easily disengaged.

Renault Logan 2014, 102 l. With. — body repair

Use our method if you no longer need the old part. Example in the video for generation 2. To implement it, you need to grab the edges of the element and pull it slightly towards you.

How to remove the bumper on a Lada Largus Plastic clips and fasteners on Renault Logan 2 are quite fragile. You need to be especially careful when removing the body kit, otherwise this part will need to be repaired or replaced.

In addition, if it is equipped with fog lights, they must be disconnected from the central electrical connector located in front of the left wheel in the lower part of the body.

A slight click of the latches indicates correct installation. Install the top screws that secure the part. Tighten the bolts on the side of the fender liners.

Screw the fasteners into the lower front part of the car. Install protection, provided that it has been dismantled. Replacing the rear bumper To remove the rear bumper from Renault Logan, you will need to: Dismantle the light bulb that illuminates the license plate, mudguards and rear wheel arch liners.

Unscrew the mounting bolt located at the rear in the left wheel arch. Use a screwdriver to press out the pins. Pull the side part of the body element and disengage the latches. Remove the five mounting bolts from the bottom.

All removed parts are laid out depending on their purpose. The side bolts are placed in one place, and the front and rear bolts in another. This sorting will greatly facilitate the process of installing the body kit on a vehicle.

How to reinstall the rear bumper To reinstall the rear bumper, you will need to perform all operations in the reverse order of disassembly.

In this case, the procedure has a number of nuances: You need to ensure that the clamps located on top fit exactly into the grooves intended for them.

This rule also applies to other fasteners.

There is nothing difficult about removing and installing bumpers on Renault Logan yourself.

Preparing tools and accessories

To perform the operation, you will need a set of tools that every motorist has in the garage. When replacing the rear and front bumpers of Renault Logan, you will need:

  • Flat head screwdriver.
  • Open-end and socket wrenches “10”.
  • Torx keys (T20-30) have a tip in the form of a six-pointed star.

To change a car body part, you will need to drive the vehicle to an inspection pit, or use a lift. Thanks to this, replacing the element will be more convenient.

Immediately before dismantling, you need to clean the bottom and fender liners. This procedure will prevent dirt from falling off during operation.

Removing front and rear bumpers on Renault Logan

The first cars appeared more than a hundred years ago - modern models are very different from what the world first saw in the 18th century.

Of course, some similar features have been preserved, such as four wheels, but this is about the only thing that has not changed since then.

Suffice it to say that initially vehicles were controlled using a lever system, but not the round steering wheel that every modern car is equipped with today.

One of these changes was the appearance of a car bumper, which today is a mandatory element of any vehicle, including such a popular model in our country as the Renault Logan.

Bumper function on Renault Logan

This element of a modern four-wheeled vehicle has two main functions:

  • Protective;
  • Aerodynamic.

In the first case, this part of the car protects the vehicle from minor damage, which occurs much more often than serious road accidents.

It is much easier to replace the front and rear bumpers of a Renault Logan car with new elements than to correct other, more serious damage to the car, for example, deformation of its body during an unauthorized collision with something.

The second function of this element is no less important - specially created shapes increase downforce, which allows the car to behave better at high speeds, and also prevents the formation of a vortex flow behind the car while it is moving.

Bumper Removal Procedure

There are a few important points to keep in mind when going through this process:

  • Both elements can be replaced by the car owner himself - it is enough to have a certain amount of time and a minimum set of technical skills;
  • Before starting the procedure itself, it is necessary to secure the vehicle well. It is recommended to install your Renault Logan on a standing brake, as well as install special pads for its wheels. This will give a chance to prevent accidents during the planned process, as well as simplify and speed up its implementation.

Removing the front bumper

In order to remove the front bumper of Renault Logan, you will need to complete the following steps:

  1. Three fasteners are removed, which are presented in the form of screws.
  2. Two sections of mudguards located in the lower part of the structure are being dismantled.
  3. The bracket is disconnected by sequentially dismantling special pistons.
  4. The next three screws are removed, which hold the system in the area of ​​​​the apron of the car's wings.
  5. The last four fasteners located on the vehicle radiator are disconnected.

Removing the rear bumper

Removing the rear bumper on a Renault Logan will be as simple as performing a similar procedure for the structure located in the front of the car:

  1. Initially, the fixing piston is dismantled.
  2. The next step is to remove the fender liners.
  3. The structure is detached from the rear fender liners - to do this, you need to unscrew the two fasteners located on them.
  4. The fasteners located in the wheel arches of the vehicle are dismantled.
  5. The luggage compartment opens, where the procedure for removing fasteners is repeated.

Video: Replacing the rear bumper of Renault Logan

The product is completely detached - you can completely remove it from the car in order to exchange it for a new one or, after repair work, return it to the place of use.

Basic information about the bumper

The bumper is an energy-absorbing device of any car in the form of a bar. It performs the function of protecting the car from severe damage during minor road accidents . This is an integral part of the body, which must perform not only a protective function, but also look harmonious. Such harmony is achieved thanks to modern materials. Most often, the bent edges of the bumper serve as spoilers, which increase downforce and prevent the appearance of a vortex behind the edge.


Rear bumper Renault Logan

Procedure for removing and replacing bumpers

Removing and replacing parts like the front bumper:

  1. We unscrew the three screws that secure the front bumper and the lower part of the engine mudguard (on the right);
  2. Unscrew the two lower sections of the mudguards (left);
  3. We disconnect one piston at a time, which fastens the bracket to the body;
  4. We unscrew the 3 screws that are fixed to the front fenders and the body in the front wheel arches;
  5. Unscrew the 4 screws that secure the casing to the car radiator frame;
  6. Unpin it;
  7. Install the new front bumper in reverse order.

Removing and replacing parts such as the rear bumper:

  1. Disconnect the piston that secures this part;
  2. Remove the wheel arch liners;
  3. On both sides of the car, unscrew two screws that secure the fastening to the rear fender liners;
  4. We unscrew one screw at a time that secures it to the rear wheel arches;
  5. Open the rear trunk and unscrew the 3 screws in the trunk opening, which provide external fixation;
  6. Unfasten the rear bumper;
  7. Install the new bumper in the rear.

Eliminating sagging front and rear bumpers

What to do if the front bumper is sagging?

To eliminate sagging, it is necessary to make two additional fasteners of the desired shape in advance. Aluminum corners are great for making them. After making the fasteners, you need to remove the front bumper. Next, adjust and install them; if necessary, you can cut off the original plastic mount. After this, install and assemble the front bumper.

Quite often, car enthusiasts are faced with the problem of sagging rear bumper of Renault Logan. It does not need to be removed to perform this procedure.

So, the algorithm of actions:

  1. Unscrew the upper screw of the wheel arch;
  2. Unscrew the bolt that is attached to the wing;
  3. Unfasten and replace the bolts that secure it to the M8;
  4. Remove the white pins that hold this trim;
  5. Correct the holes and replace the pistons with bolts.

Secrets of installing the front element

In this situation, the slogan “Installation is the opposite of removal!” not entirely relevant. This is due to the fact that owners often do not observe accuracy during installation, and this provokes the formation of damage to the paintwork. In view of the above, we recommend performing the installation process of the element together with an assistant.

First, we carefully “adjust” the Renault Logan bumper to the seat. To do this, wearing soft gloves, we grasp the edges (at the same time) and slowly slide it along the guides. To ensure the comfort of the “operation”, we dismantle the plastic protective structures and fix it on each side of the car. We screw in the 4 bolts at the top without resorting to fully tightening them. In a similar way we attach the screws on the sides. We achieve the required uniform gap between the body panels and the surface and subsequently fully tighten the indicated upper bolts. We screw in three bolts from below and immediately mount the plastic protection. We tighten the self-tapping screws. After tightening the fasteners, we check the correct fit. This completes the procedure

This completes the procedure.

How to install the rear bumper?

You already know how to remove the rear bumper, but how to install a new one? By analogy with the front element, the process of installing the bumper in the rear is carried out with the assistance of an assistant. We also arm ourselves with gloves and cover the edge panels of the bumper with masking tape (recommended, but not required).

  1. First, we try on the element to the seat.
  2. Then we hang it on the guide brackets of the body (located on the side surfaces of the rear wings).
  3. We push the bumper all the way and immediately install the license plate light.
  4. We adjust the size of the gap, achieving its uniformity along the perimeter of contact between the bumper and body panels.
  5. We tighten the entire list of fasteners in their locations. We start this procedure with the bolts at the top. Do not forget about the need to fix the 3 central bolts from below.
  6. We return the plastic protection elements on both sides of the structure to their place.

We remove the tape, check the tightness of the fasteners and the uniformity of the gap. That's all - the bumper is in place.

RENAULT LOGAN 2 NEW. Installing a mesh in the bumper. Removal and installation iaarus.ruT LOGAN II

Screw in the four bolts at the top without fully tightening them. Don’t be afraid to damage anything, everything is located far away. We don’t remove the jack from under the bumper.

Grab the edges of the part with a partner, and then carefully bring this part to the place of its installation

Then unscrew the bumper from the fender liner and unscrew another bolt securing it to the side of the body….

In some cases, when replacing this body element, Renault Logan owners, without being careful during the installation phase, risk damaging the paintwork. This work takes about ten minutes, and anyone, even an inexperienced Renault owner, can carry it out.

A simple and affordable bumper replacement for every driver makes it possible to maintain the aesthetic appearance of their car in proper condition without going to a car service center, and this saves both time and money. Removing this part on Renault Logan is carried out in a slightly different way and requires a certain tool.

The upper bumper mount will move slightly. Take a utility knife and cut out small rectangles and screw the bolts back in.

That's it, the jack can be removed. The bumper no longer sags, the gaps have become much better and the bumper now holds very tightly, there is no play.

Next, I took colorless silicone sealant and applied it under the headlights and between the fender and bumper. I degreased everything first with a degreaser.

bumper mounting bracket for Renault Logan/Sandero, bumper repair, spare parts overview

Remove excess with a wet, clean cloth. When I was driving from my parents on May 1, we got caught in a short but rather heavy rain on the way.

Self-recovery

Of course, it is easiest to repair an unpainted bumper. In addition, scratches on it are almost invisible, so basically only large defects such as cracks are eliminated. One way to restore a bumper is gluing. To do this, you will first need glue and sandpaper. You can purchase a repair kit that includes, in addition to these components, a hardener.

Most often, bumpers are glued with epoxy glue, but Renault Logan owners say that this substance does not interact well with the plastic of the bumper, so they recommend additionally reinforcing it with fiberglass in several layers.

Work begins by treating the damaged area with coarse sandpaper, after which it is degreased. Then, glass fiber fragments pre-impregnated with epoxy glue are placed on the crack, one on top of the other, taking breaks for the polymerization of each of them. In addition, each layer of material must be sanded with sandpaper after polymerization.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]