Print this article Font size 16
Fuse blocks installed on old and updated versions of VAZ 2109 cars serve to combine all electrical wiring.
The main task of the power supply is to prevent breakdowns of electrical equipment installed in the car.
Where are the fuses VAZ-2108 2109 21099
The relay and fuse block for the VAZ 2108-09-099 (carburetor, injector) is located under the hood, in the compartment in front of the windshield on the left side.
Fuse mounting block 2114-3722010-18
- K1-relay for turning on headlight cleaners;
- K2-relay-breaker for direction indicators and hazard warning lights;
- K3 - windshield wiper relay;
- K4-relay for monitoring the health of lamps;
- K5-power window relay;
- K6 - relay for turning on sound signals;
- K7-relay for turning on the electric heating of the rear window;
- K8-relay for high beam headlights;
- K9-relay for low beam headlights;
- F1-F16 - fuses
Fuse mounting block 2114-3722010-60
- K1 - Relay for turning on headlight cleaners
- K2 - Relay interrupter for direction indicators and hazard warning lights
- K3 - Windshield wiper relay
- K4 - Relay for monitoring the health of brake lamps and side lights
- K5 - Power window relay
- K6 - Horn relay
- K7 - Heated rear window relay
- K8 - Headlight high beam relay
- K9 - Relay for low beam headlights
- F1 - F16 - Fuses
- F1 - F20 - Spare fuses
Fuse mounting block 17.3722
- 1 - relay for turning on headlight cleaners (K6)
- 2 - rear window washer time relay (K1)
- 3 - relay-breaker for direction indicators and hazard warning lights (K2)
- 4 - windshield wiper relay (KZ)
- 5 - contact jumpers in place of the lamp health monitoring relay
- 6 — relay for turning on the heated rear window (K10)
- 7 - spare fuse
- 8 - headlight high beam relay (K5)
- 9 - relay for low beam headlights (K11)
- 10 - fuse
- 11 — relay for switching on the electric motor of the engine cooling fan (K9)
- 12 - horn relay (K8)
Description of the mounting block fuses for VAZ 2109, 2108, 21099
F1-F16 - mounting block 2114-3722010-60, 2114-3722010-18.
Numbers from 1 to 16 - old-style mounting block 17.3722
Fuse no. | Decoding |
1 (8 A) F9 (7.5 A) | Right fog lamp |
2 (8 A) F8 (7.5 A) | Left fog lamp |
3 (8 A) F1 (10 A) | Headlight cleaners (at the moment of switching on). Relay for turning on headlight cleaners (contacts). Headlight washer activation valve |
4 (16 A) F7 (30 A) | Headlight cleaners (in operating mode). Relay for turning on headlight cleaners (winding). Heater fan motor - heater fuse Window washer motor. Rear window wiper motor. Rear window washer timing relay. Valves for turning on the windshield and rear windows. Relay (winding) for turning on the electric fan of the engine cooling system. Relay (coil) for turning on the heated rear window. Rear window heating indicator lamp. Glove compartment lamp |
5 (8 A) F16 (15 A) | Direction indicators and relay-interrupter for direction indicators and hazard warning lights (in turn indication mode). Turn signal indicator lamp. Rear lights (reversing lamps). Gearmotor and windshield wiper activation relay. Generator excitation winding (when starting the engine). Brake fluid level warning lamp. Oil pressure warning lamp. Carburetor air damper warning lamp. Parking brake warning lamp. "STOP" light display lamp. Coolant temperature gauge. Fuel level indicator with reserve warning lamp. Voltmeter |
6 (8 A) F3 (10 A) | Rear lights (brake lamps). Interior lighting |
6 (8 A) F6 (30 A) | Power windows for front doors. Power window relay |
7 (8 A) F10 (7.5 A) | License plate lights. Engine compartment lamp. Instrument lighting lamps. Indicator lamp for external lighting. Heater lever illumination display. Cigarette lighter lamp |
8 (16 A) F5 (20 A) | The electric motor of the engine cooling system fan, and its activation relay (contacts). Sound signal and relay for its activation |
9 (8 A) F10 (7.5 A) | Left headlight (side light). Left rear light (side light) |
10 (8 A) F11 (7.5 A) | Right headlight (side marker). Right rear light (side light) |
11 (8 A) F2 (10 A) | Direction indicators and hazard warning relay-breaker (in hazard warning mode). Hazard warning lamp |
12 (16 A) F4 (20 A) | Rear window heating element. Relay (contacts) for turning on the heated rear window. Plug socket for portable lamp. Cigarette lighter |
13 (8 A) F15 (7.5 A) | Right headlight (high beam) |
14 (8 A) F14 (7.5) | Left headlight (high beam). Indicator lamp for high beam headlights |
15 (8 A) F13 (7.5 A) | Left headlight (low beam) |
16 (8 A) F12 (7.5 A) | Right headlight (low beam) |
Starter relay
The starter relay is located under the hood on the front panel.
Scheme
The entire line of VAZ 2109 cars can be divided into two branches - those produced before 1998 and those produced after 1998.
Older cars are equipped with fuse blocks whose marking is 17.3722. This power supply consists of a housing and an engineering board. Wire contacts, fuses and relays are soldered to the board.
Newer versions of nines, the production of which began in 1998, here the power supply is marked 2114-3722010-60. Here we are already seeing fuses.
If we talk about fuse blocks, the factor of the fuel injection system used - carburetor or injector - plays absolutely no role. BP will differ only by the year of manufacture of the car. Therefore, the mounting blocks for the carburetor and injector are the same.
The required mounting block is also located the same everywhere - in the engine compartment opposite the driver's seat, almost under the windshield.
Location
Differences
Are there any differences between the old and new versions of the power supply? Of course. They are as follows:
- The parts of the mounting block are marked differently;
- The fuse ratings are different;
- The new power supply does not have a relay for the cooling system fan motor and a time relay for the rear window washer device.
Decoding the fuse and relay block VAZ 2109 2108 21099, old model
Decoding the fuse and relay block VAZ 2109 2108 21099 old model
Fuse number | Current strength | The chain he protects |
F1 | 10A | Backup fuse |
F2 | 10A | Turn signal indicators, hazard signal breaker (in hazard mode), hazard warning light |
F3 | 10A | Rear brake lights, interior lighting |
F4 | 20A | Rear window heating element, rear window heating switch contacts, carrying socket, cigarette lighter |
F5 | 20A | Horn (horn), horn switch |
F6 | 30A | Backup fuse |
F7 | 30A | Heater fan electric motor, windshield washer electric motor, electric radiator fan relay, rear window heating relay, rear window heating indicator light, glove box light |
F8 | 7.5A | Backup fuse |
F9 | 7.5A | Backup fuse |
F10 | 7.5A | Left side light |
F11 | 7.5A | Right side lamp |
F12 | 7.5A | Right low beam headlight |
F13 | 7.5A | Left low beam headlight |
F14 | 7.5A | Left high beam headlight, high beam indicator lamp |
F15 | Right high beam headlight | |
F16 | 15A | Turn signal indicators and emergency flasher relay-breaker (in the turn signal indication mode), turn signal indicator indicator lamp, rear reverse lights, gear motor and windshield wiper activation relay, oil pressure indicator lamp, hand brake indicator lamp, coolant temperature indicator, fuel level indicator, fuel reserve warning lamp, voltmeter |
Relay
Relay number | Functions |
1 | Performance of the front optics cleaning elements |
2 | Rear window washer motor performance |
3 | Protection against breakage of turn signal and light signaling lamps |
4 | Protection against failure of the windshield wiper motor |
5 | Allows you to determine the performance of the lamp |
6 | Rear window defogger overvoltage protection |
8 | High beam lamps |
9 | Low beam lamps |
11 | Responsible for the operation of the engine cooling fan. If this relay fails, the risk of engine overheating increases. |
12 | Klaxon operation |
Dismantling and replacement
If one or another equipment fails, you must first check the condition of the fuse responsible for it.
In practice, removing and removing an unusable fuse or relay is not difficult. To do this you need:
- Raise the hood and disconnect the minus from the battery. Since you are working with the fuse box responsible for electrical equipment, the car should not be energized at this moment;
- Find the mounting block. It is located in the engine compartment opposite the driver's seat directly under the windshield. The top of the block is covered with a plastic cover. To remove it, simply press the latches on the sides;
- Remove the cover and look at the back side. There is an electrical diagram showing the location of one or another fuse or relay. Just find the element that is responsible for the failed equipment according to the tables above;
- Remove the fuse. All mounting blocks are equipped with special pliers. Manually removing fuses is not recommended. The relays are removed by gently rocking up and down;
- Replace the failed component.
Fuse failure is determined by the melted filament. These are fusible elements that melt and make contacts, preventing equipment from being damaged by excessive voltage.
That's it, all that remains is to replace the fuse block element, close the cover, replace the battery terminal and check the functionality of the equipment.
Decoding the fuse and relay block VAZ 2109 2108 21099, new model
The decoding is relevant for both carburetor and injection types of engines.
Fuse number | Rated current | The electrical circuit for which it is responsible |
1. | 8A | Backup fuse |
2. | 8A | Backup fuse |
3. | 8A | Backup fuse |
4. | 16A | Radiator fan relay winding, electrical circuit of switch and heater motor |
5. | 3A | Hazard warning switch in turn signal mode, turn signal switch, turn signal switch, turn signal warning light, turn signal warning light, reverse optics switch, reverse lights, tachometer, voltmeter, gasoline level indicator, gasoline level sensor, gasoline level warning light, pointer coolant temperature, temperature sensor, warning lamp and emergency oil pressure sensor, brake emergency lamp, brake system hydraulic switch, hand brake switch |
6. | 8A | Brake light switch and bulbs, interior lighting |
7. | 8A | Room lighting lamps, indicator lamp for switching on the dimensions, lamp for illuminating the heater and cigarette lighter handles, glove compartment lamp, switch and lamp for instrument panel illumination |
8. | 16A | Horn, horn switch, radiator fan motor |
9. | 8A | Left side lamp, left rear side lamp |
10. | 8A | Right side lamp, right rear side lamp, fog light switch, fog light indicator light |
11. | 8A | Turn signal switch and breaker, turn signal lamps, warning lamp in emergency mode |
12. | 16A | Cigarette lighter, socket for carrying lamp |
13. | 8A | High beam right headlight |
14. | 8A | Main beam of the left headlight, high-range optics warning lamp |
15. | 8A | Low beam right headlight |
16. | 8A | Low beam left headlight |
Relay
Relay number | Its functions |
K1 | Without it, the rear window washer motor will not work. |
K2 | Responsible for the operation of turn signal lamps and light signaling |
K3 | Provides operation of the windshield wiper |
K4 | Protects brake lights and vehicle dimensions |
K5 | Provides operation of high beam lights |
K6 | Guarantees operation of the optics washer device |
K7 | Protects the power window motor if your vehicle has one. |
K8 | Sound signal or just a horn |
K9 | Protects against high voltage going to the engine cooling fan |
K11 | Responsible for the operation of the rear window heating device |
K12 | Provides operation of low beam lights |
Diagram of the mounting fuse block for VAZ 2109, 2108, 21099 (block 17.3722)
In the diagram: (the outer number in the designation of the wire tip is the number of the block, and the inner number is the conventional number of the plug)
K1 — rear window washer time relay; K2 - relay-interrupter for direction indicators and hazard warning lights; KZ - windshield wiper relay; K4 - relay for monitoring the health of the lamps (contact jumpers are shown inside, which are installed instead of the relay); K5 - headlight high beam relay; K6 - relay for turning on headlight wipers; K7 — power window relay; K8 - horn relay; K9 - relay for switching on the electric motor of the engine cooling fan; K10 — relay for turning on the heated rear window; K11 - relay for low beam headlights.
Diagram of the mounting fuse block for VAZ 2109, 2108, 21099 (2114-3722010-60)
K1 - relay for turning on headlight cleaners; K2 - relay-interrupter for direction indicators and hazard warning lights; KZ - windshield wiper relay; K4 - lamp health monitoring relay; K5 - power window relay; K6 - relay for turning on sound signals; K7 — relay for turning on the heated rear window; K8 - headlight high beam relay; K9 - relay for low beam headlights; F1-F20 - fuses.
Very often, car owners are looking for: Where is the fuse or heater relay on a VAZ 2109? Answer: there is no fuse and heater relay for VAZ 2108, 2109, 21099. Older models have an ignition relay, through which the stove is also powered, see photo below.
In the latest VAZ models, the stove is powered directly through the ignition switch.
How to remove and replace the block
Such an operation may be necessary if it is necessary to repair the power supply or replace it with a new unit. Even a novice driver can do this. You will need a 10mm wrench (it is best to use a socket or socket). Before removing the power supply, open the hood of the car's engine compartment.
Procedure for removing the power supply:
- Disconnect the terminals from the battery. This is necessary to prevent the possibility of a short circuit in electrical equipment.
- For ease of operation, remove the protective plastic top cover of the power supply unit.
- The block is secured to the body with two screws (they are removed with a wrench).
- Disconnect the connectors with wires. One of them is located in the engine compartment on the wide side of the block closer to the windshield. First, remove the rubber protective cover, and then, rocking it from side to side, disconnect the connector.
- The remaining connectors are located at the bottom of the power supply. To get to them, remove the two outer relays, painted black. After this, the power supply housing is lifted up and the remaining connectors are disconnected.
The unit is removed from the engine compartment for repair or replacement. Reinstalling it is carried out in the reverse order. In this case, pay attention to the rubber gasket between the power supply and the car body. It must be intact, without cracks or tears, otherwise it must be replaced with a new one. The gasket is needed to protect the power supply from moisture, which can cause a short circuit in the car's electrical circuit.
Watch the video of the AvtoMalina channel about removing the VAZ 2109 fuse box