✅ Reset Skoda Octavia A7

Octavia A7 maintenance cost

The third technical inspection is a repetition of TO-1. Maintenance 4 is one of the key car services and one of the most expensive. In addition to replacing the materials necessary for passing TO-1 and TO-2. It is necessary to replace the spark plugs, oil and filter of the automatic transmission/DSG (6-speed diesel) and the fuel filter on a car with a diesel engine.

The average cost is indicated as of prices for autumn 2022 for Moscow and the region.

TO 1 is basic, as it includes mandatory procedures that will be repeated when new ones are added to the next TO. The average price at a service station of a dealer network for replacing the engine oil and filter, as well as the cabin filter, will cost 1,200 rubles.

TO 2 in addition to the maintenance provided for in TO 1, the replacement of the air filter (500 rubles) and brake fluid 1200 rubles is added, for a total of 2900 rubles.

TO 3 is no different from TO 1, with the same set price of 1200 rubles.

Maintenance 4 is one of the most expensive maintenance, as it requires the replacement of almost all replaceable materials. For cars with gasoline engines, in addition to the costs established by maintenance 1 and maintenance 2, it is necessary to replace the spark plugs - 300 rubles/piece. Total 4100 rub.

On cars with diesel units, in addition to replacing the specified maintenance 2 and maintenance 1, it is necessary to change the fuel filter and oil in the DSG (with the exception of cars with the Common Rail system). Replacement of the fuel filter - 1200 rubles. An oil change will cost 1,800 rubles, plus a filter replacement will cost 1,400 rubles. Only 7300 rubles.

TO 5 repeats TO 1.

TO 6 repeats TO 2.

TO 7 work is performed by analogy with TO 1.

TO 8 is a repetition of TO 4, plus replacing the timing belt - 4800 rubles.

Total

The decision which routine work to undergo at a service station, and which you can handle with your own hands, you make based on your own strengths and skills, remembering that all responsibility for the actions performed lies with you. Therefore, you should not delay the next maintenance, as this may affect the performance of the car as a whole.

Carrying out maintenance and work

Changing the oil on the Skoda Octavia Tour A5 occurs in standard mode. On 1.8 tsi engines, you need to remove the crankcase protection and drain the old oil, then change the oil filter. It is also necessary to replace the cabin and engine air filters, these are consumables.
Brake pads are changed in accordance with the rules for repair and operation of Skoda Octavia Tour A5, A7, Scout. RS models are equipped with more powerful brakes, which affects their maintenance costs. These consumables need to be changed both from the front and from the back. The work can be done independently only from the front side of the car.
Work on replacing the timing drive on Skoda Octavia Tour A5, A7 vehicles must be carried out in accordance with the manufacturer’s data list. RS versions have a shorter timing drive life, since this car is designed for increased loads. Spare parts should be purchased in the original version, otherwise there is a high chance of stumbling upon a fake. It is better to do timing belt maintenance work at a dealer.
The brake fluid for the Skoda Octavia Tour A7, Scout must be changed every 2 years, regardless of mileage. This is because this liquid quickly absorbs moisture and becomes less effective. On RS versions, it is better to carry out maintenance of the brake system no later than after 2 years, since the brake system on this car is subject to increased loads. Resetting the indication during this replacement is not provided, and the work is performed only by dealers.
Antifreeze for the Skoda Octavia Tour A7, Scout with a 1.8 tsi engine needs to be changed every three years of active use. Otherwise, defects may appear in the cooling system. TSI engines are very picky about coolant, since these units are equipped with a turbo system, which significantly increases the operating temperature of the engine. Maintenance of the refrigerant system is an important event that should not be forgotten.
Skoda Octavia Tour A5, A7, Scout 1.8 tsi requires regular maintenance of the power system. The fuel filter on tsi engines needs to be changed quite often, this is due to the fact that this unit has high-performance fuel injectors, the thickness of the nozzles in which is several times smaller than that of a conventional engine. These spare parts cannot be repaired if they fail; this is especially important for owners of Skoda Octavia Tour A5, A7, Scout tsi.
Consumables and spare parts need to be changed every year, since the Skoda Octavia Tour A5, A7, Scout appears to be a reliable car. Prices for consumables and spare parts for this car do not exceed the offers of competitors, and are often cheaper.
Reset. To reset the service and remove it from the instrument panel, you need to press special keys.

Skoda Octavia (2017). Guide - part 12

The set speed limit can later be changed manually if necessary.

Reset speed limit

Select the menu item Warning. at

() or  () and confirm your selection.

When the saved value is confirmed, the speed limit is reset.

The selected speed limit is also retained after turning off and then turning on the ignition. If traffic stops for more than 2 hours, the set speed limit value is automatically deleted.

Ill. 29 Display of memory blocks: MAXI DOT display (


)/segment display (

)
The system stores data in three memory blocks, described below, shown on the display in the field

With mom. start (


) or “1” (

)
This memory records trip data from the moment the ignition is turned on until the moment the ignition is turned off.
If driving resumes no more than 2 hours
after the ignition is turned off, the new data is added to the data of the previous period and saved together with them as one trip.
If a trip is interrupted for more than 2 hours,
the trip data is automatically deleted.

For length period (


) or “2” (

)
This memory records data from any number of individual trips for a total driving time of up to 99 hours 59 minutes or for a total mileage of up to 9999 km. If one of the specified values is exceeded, the display starts from zero again.

From the moment of refueling (


) or “3” (

)
This memory stores trip data from the last time you refueled. The next time you fill the fuel tank, the values are automatically deleted from memory.

To select memory

Confirm the selected data again and select the desired memory.

To reset memory

Press and hold the confirmation key for the selected memory.

The following movement parameters are stored in memory:

Average fuel consumption.

Average driving speed.

When disconnecting the vehicle battery terminals, the data of all memory blocks is erased.

MAXI DOT display

This chapter contains information on the following topics: Menu item Navigation

The MAXI DOT display (hereinafter simply display) shows data from the Infotainment system, on-board computer, driver assistance systems, etc., depending on the vehicle's equipment. You can navigate to the menus and call up the data display using the buttons on the steering column switch or on the multifunction steering wheel.

Main menu items (depending on equipment)

CO Warning

So, you don’t need to worry about when you need to go to a service center to undergo the maintenance prescribed by the automaker - the on-board vehicle of your Octavia .

Regardless of whether you own a car manufactured in 2012 (2nd generation) or have a liftback of the latest generation (2014, 2016 and later), if you have driven 14,000 km since the last maintenance, you have When you turn on the ignition, the image of a key will light up on the dashboard for 10 seconds. At the same time, the information monitor will display the number of km and days remaining until the maintenance is completed.

After the arrival of the fateful date, the key sign will glow for 20 seconds after turning on the ignition and at the same time the inscription Service now will appear! And it will not go out until you reset the Skoda Octavia A5 service.

If the car is under warranty, or you prefer to have it serviced by service technicians even after the warranty period has expired, you have nothing to worry about - they will reset all the necessary counters themselves.

But many car enthusiasts prefer to carry out maintenance without the help of others - this allows them to save significantly. Obviously, such a solution will require you to independently reset the inspection interservice period. And although the manufacturer advises doing this operation exclusively in authorized service centers, there is nothing complicated about it, so reset the service interval of the Skoda Octavia A5 in almost a couple of minutes, and you don’t need any tools other than your hands.

Skoda A7 Inspection Service Reset

Instructions for restoring service intervals on Skoda cars: Fabia, Rapid, Octavia, Yeti, Superb and Roomster with photo and video explanations.

Of course, every owner of a Skoda car has at least once encountered such a car function as a reminder of the inevitable maintenance. This warning looks different depending on the model and year of the car, sometimes it flashes and sometimes it sounds when you start the engine. But it has the same purpose - to remind you of the need to undergo a technical inspection of the car (changing engine oil, filters, etc.).

The reminder interval is 372 days or 15,000 kilometers, whichever comes first.

To shorten the service interval, you do not need to contact the service and pay money for a simple procedure. You can do everything yourself.

Consider resetting the technical interval for different Skoda models.

Note from iLoveSkoda.ru: We tried to describe in detail all the options for resetting metrics for each Skoda model, but due to the large number of configuration parameters, the described method will probably not work for you. In this case, read the instructions for other models. One of them is definitely suitable for your car.

How to remove Skoda Fabia maintenance reminder

Skoda Fabia 2nd generation and its restyling (year of manufacture: 2007 - 2010, 2010 2014)

All. Reset mileage between services.

Video instruction

Skoda Fabia 3 New (from 2014)

Press the lever to reset the daily mileage and turn on the ignition.
When the entire display goes dark, release the lever you held in step 1 and turn it to the right. If everything is done correctly, the service key image will disappear.
Turn off the ignition.

footage

How to reset the service interval on an Octavia

resetting the service interval on the Skoda Octavia A5

Press and hold for about 10-15 seconds to reset the daily mileage, including ignition.
Then turn this button to the right until 15,000 km appears.
You need to reset a long distance on the Skoda Octavia on-board computer.

video

We eliminate the need for maintenance on the Skoda Octavia A7

When the ignition is turned off, hold the button responsible for resetting the distance traveled during the day.
After 10-15 seconds you need to turn on the ignition (the key is still clamped).
Release the button. category consideration
Service for the Skoda Rapid 2016 model year One of the maintenance interval options appears on the on-board computer screen. Select the desired value (press the button until the desired indicators are displayed).
Turn off the ignition.

video

Leave the inscription "Service" on the Skoda Tour of the Octavia

Press the lever to reset the vehicle's daily mileage. Then turn on the ignition and release the clamped lever.
Turn the clock control lever (located on the left, closer to the tachometer) to the right, the “Service” inscription should disappear from the on-board computer display.
Turn off the ignition.

How to reset inspection service on Skoda Octavia A7

Everything is quite simple. discharge

It will take you no more than one minute. How to reset oil

Resetting the Rapid oil change service indicator

There are several options for resetting values, depending on the presence of Maxidot on the instrument panel.

Maxidot (Maxidot) is a type of on-board computer. Located in the center of the dashboard between the tachometer and speedometer. To quickly determine its presence or absence, see if the car icon is displayed (see picture); if so, it is there. Otherwise, you have a regular on-board computer.

Photo 3. On-board computer Maxidot.

If your car does not have a Maxidot, then you need to do the same steps as for the 2nd generation Fabia.

If available, do the following:

Press and hold the daily mileage reset button (the ignition must be turned off!).
Turn on the ignition (continuing to hold the key). A display appears with the inscription “Reset
the oil change service
On the wiper activation lever, press button 2 (diagram No. 6).

Diagram 6.
The message “The indicator has been reset” appears, after which we turn off the ignition.

Video instruction

Skoda Roomster 1.4 2013 With maxi dot display. To reset the maintenance, you need to press the button on the wiper lever at the end (up or down) with the ignition on (up or down) and hold for about five seconds. A screen will appear with the words DISPLAY, STATUS and SETTINGS, select SETTINGS with the lower separate button. Down we look for the “MOT” inscription, click the bottom round button, it will be prompted to ZERO, select that’s it, the next service will be in 15,000 km

Clearly it turned out to be reset. From the first time, I have a Skoda Roomster. Good advice!

Skoda Fabia 2013 without maxidot, according to the above diagram, only the number of km until the next one is reset, then the number of days remains the same, the key does not disappear anywhere

How to reset the service interval

The appearance of a signal about the need for maintenance is a common problem that almost every motorist has encountered. In this case, the display may flash and the device may make annoying beeps. In service centers, when resetting, they make an entry in the service book and stick a sticker indicating the date of the next maintenance. Manufacturers do not recommend resetting the data yourself, as the indicator settings may be lost. But most often, no malfunctions in the operation of the vehicle systems are observed.

List of works during maintenance 1 (15,000 km)

Checks during maintenance 1 and all the following:

Visual control of the integrity of the windshield;
Checking the operation of the panoramic sunroof, lubricating the guides;
Checking the condition of the air filter element;
Checking the condition of the spark plugs;
Resetting the maintenance interval indicator;
Monitoring the tightness and integrity of ball joints;
Checking the free movement, reliability of fastenings and integrity of the control rod end covers;
Visual inspection of the absence of damage to the gearbox, drive shafts, CV joint covers;
Checking the free play of wheel bearings;
Monitoring the tightness and absence of damage to the brake system;
Control of brake pad thickness;
Checking the level and adding brake water as needed;
Monitoring and adjusting tire pressure;
Monitoring the remaining height of the tire tread pattern;
Checking the expiration date of the tire repair kit;
Monitoring the condition of external lighting devices;
Monitoring the condition of the battery.

How to reset service on Skoda Octavia (A7, A5, A3)

Depending on the configuration, information can be displayed on the display or multifunction screen. To reset on a car with a regular display, for example Octavia A3 , you must perform the following steps:

Turn on the ignition.
Press and hold the knob located to the right of the screen for 5 seconds.
Without releasing the button, turn on the ignition again.
Now you need to turn the knob to the right or left. The service interval has been reset.

Octavia A5 models produced before 2015, the instructions presented above will not work. The operation is performed according to the following scheme:

Press and hold the mileage reset regulator for about 15 seconds. At the same time, activate the ignition.
Turn the regulator to the right. The display will show the value “15,000 kilometers”.
You need to wait a few seconds and make sure that the data has been successfully reset.

The next generation of cars from the Czech automaker is Octavia A7 , which began production in 2013. To reset the service interval on this machine, you will need to follow a few simple steps:

Without turning on the ignition, press the switch on the right. It is intended to reset the counter of the distance traveled per day.
After 15 seconds, turn the ignition key.
You can now release the switch. The display will display a menu with several options; here you need to select zeroing the service interval.
You can then reactivate the ignition.

Video on how to reset the interval on the Octavia A7:

Helpful information

On the third generation model, several types of on-board computers are installed. The most popular of them is BC Maxi Dot. In this regard, manually the service In cases where after the operation it was not possible to achieve the desired result, you should use the services of the VAG COM diagnostic device and the Vasya Diagnost software.

In some modifications of the model, information messages on the on-board computer display are duplicated with sound signals. Such reminders irritate the driver even more, preventing him from concentrating on driving, which forces him to quickly reset such information.

You cannot underestimate the signals sent by the on-board computer about resetting the maintenance on the Skoda Octavia A7. Technical inspection helps maintain normal performance of the Czech model and its components.

Timely replacement of engine oil will ensure uninterrupted operation of the power unit for two hundred or more thousand kilometers. Replacing filter elements in various systems will protect units from contamination and premature failure. Such reminders from the on-board computer remind the owner of the Skoda Octavia A7 about the timing of maintenance.

How to reset the oil service on a Skoda Octavia A7, see this

How to reset the inspection service on a Skoda Rapid

The action algorithm is selected based on which on-board computer is installed. Difficulties may arise if the manufacturer supplied the Maxi Dot system with a built-in VAG scanner. You can quickly reset the readings by following the steps in this order:

With the ignition off, press the daily mileage switch and do not release.
Activate the ignition without pressing the button.
When a message appears on the screen about resetting the maintenance indicator after changing the oil, press the left button located at the bottom of the wiper lever.
The information should be deleted; you can remove the ignition key.

In Skoda vehicles with a standard on-board computer there are two separate reset buttons. The Rapid model uses a double button with the following symbols: Set – to switch display modes and reset data, 0.0 – reset the TO indicator.

If the car was manufactured after 2013, you must turn on the
You need to turn everything off, then hold down the “set” key, it’s on the right.
After a few seconds, turn on the ignition
Release the button.

The left side of the key labeled “0.0” does not need to be used. It is clicked when the oil interval is reset. For models equipped with a multifunction display, the procedure is different. You must turn on the ignition and follow the instructions:

Click on the lower right button and do not release until the menu opens.
Quickly press the lower left key.
Press and hold the right button again until the “Setup” message appears.
Then briefly press the second key.
Repeat steps from step 3. “Service” should appear on the screen.
Perform steps 4 and 5 again, wait until the “Reset” line is displayed
Click on the lower left button.
Turn off the ignition.

Adjustment of maintenance period

If you do not plan to have your car serviced by an official dealer, that is, you are not afraid to “fail” the warranty, and the inscription about the need for service annoys you, it will not be difficult to reset (reset) the “Service” inscription yourself.

On Octavia of the first (Tour), second (A5) and third (A7) generations, the operation is performed differently, although the differences are small.

How to reset (zero) the oil (inspection) service on a Skoda Octavia A7

The user manual will warn you that resetting the maintenance yourself is not advisable, since this will lead to a failure of the corresponding settings, and other disturbances in the functioning of the main vehicle systems are possible. This shouldn't scare us.

Let's look at the procedure for resetting the Octavia Tour service interval:

press the right button (under the speedometer);
without releasing it, turn on the ignition;
wait until “Service” appears on the panel;
release the right button, go to the left one and turn it clockwise at a small angle;
the “Service” inscription disappears - we have completed our task.

On the Skoda Octavia A5, to reset the service interval, proceed as follows:

with the ignition off, press the Trip button (which is intended for setting the clock);
Without releasing the button, turn on the ignition;
after a few seconds, release the button and turn it clockwise (or counterclockwise) until the numbers 15,000 appear on the information display instead of the inscription “Service”.

If you have a version with MaxiDot, which allows you to manipulate intervals at your discretion, resetting the service interval of the Skoda Octavia A5 is also performed through it: on the steering column paddle, hold down the “Up” button, a menu will appear, select the “AM Status” item. An inscription about the remaining mileage before the maintenance will appear, reset it to zero.

But this procedure does not always work. If your efforts are unsuccessful, do not be upset - you can do this using a cable (for example, VagCom).

connect the cable, select the 17-Instruments mode, and then the Adaptation-10 mode;
stop selecting the “time from inspection” item, set the time value to zero;
a question will appear about confirming the reset operation, answer in the affirmative;
a message will be displayed that the zeroing has been completed, you need to click on “OK” and we will get to the main menu;
we proceed in the same way with zeroing the mileage (item “distance from inspection”);
to reset the inscription urging you to immediately undergo maintenance, select the “Resetting ESI” item, then press the Reset button and confirm the operation;
disconnect the cable and remove the key from the lock.

READ Airbag error Skoda Octavia a7

Now let's look at how to reset the service interval of the Skoda Octavia A7:

With the ignition off, press the “0.0” button;
turn on the ignition without releasing the button;
The information display will ask if the oil change counter needs to be reset. Use the steering wheel paddle to confirm the operation;
To reset the inspection control, turn off the ignition;
turn on the emergency alarm;
press the “0.0” button;
turn on the ignition;
The question about resetting will appear again, confirm the operation.

The reset is performed in approximately the same way on all new Volkswagen and Skoda models.

How to reset the service interval on a Skoda Fabia

If the car was produced no later than 2010, it is enough to follow the following scheme:

With the engine off, press the button near the speedometer.
While holding the button, turn on the ignition.
The key must be turned to the right.
When the data is reset, turn off the ignition.

Video for cars up to 2013:

For Fabia 3 New models starting from 2014, the reset is done in the same way as described above. In Skoda Fabia cars, starting from 2011, when the oil needs to be changed, an icon with a key appears on the display. Performing the operation to reset the service interval is even simpler:

Press and hold the daily mileage button located on the right.
Without releasing the key, turn the ignition key.
Release the daily mileage button.
Now press the left key, after which the key on the screen should disappear.
The ignition must be turned off.

To check whether the measures taken helped, you need to wait a few minutes. Then turn the ignition key again and look at the display. If everything works, there will be no icon on the screen.

The second method is for cars with a multifunction display manufactured since 2011:

With the ignition on, press the button located on the right and do not release it until the main menu opens.
Press the same key again. When “Setup” is displayed, release the button and press the middle key.
Now you need to press the first button again for a few seconds. When the “Service Interval” line is highlighted, release.
Quickly press the second key, then hold down the first.
You can release the button after “Reset” is highlighted.
To reset, you need to confirm the action by pressing the left button.
Turn off the ignition.

In case of resetting reminders on the Skoda Fabia 2, produced from 2007 to 2014, the methods presented above will not work. The procedure is as follows:

You need to hold down the key used to erase the mileage.
Without releasing the button, put the key in the ignition.
Next, you need to release the mileage erase and click on the button with the folder image.
The key icon should disappear from the screen. Immediately after this, turn off the ignition and wait until the display goes off.

CO Warning

So, you don’t need to worry about when you need to go to a service center to undergo the maintenance prescribed by the automaker - the on-board vehicle of your Octavia .

How to reset the service interval on a Skoda Superb

The maintenance indicator shows how many kilometers are left until scheduled maintenance. A wrench icon appears on the screen. The display shows a message indicating how many kilometers or days a service will be required. If this moment has come, when turned on, a flashing icon with a key is displayed for 20 seconds. The following message appears on the screen: “Service now!”

It is easy to reset data on Skoda Superb cars starting from 2008. But first you have to figure out the location of the buttons on the multifunction steering wheel. On the right there is a wheel with which you select items in the menu. You will also need the lower left switch with an arrow; it is used to go to the settings section. The interval is reset as follows:

Turn on the ignition.
Press the switch located under the steering wheel down and wait until the main menu opens.
The switches on the steering wheel will be used as arrows when navigating through the menu.
You must select the “Settings” item, then go to the “TO” section.
Next, you need to click on the inscription “Reset”, when the request appears on the screen, answer “Yes”.

If an LCD information display is installed, you need to go to the menu to get information about how many kilometers are left before the service. To do this, you need to go to the “Settings” section. The operation is performed according to the same scheme as on the Fabia model with an LCD screen.

For the Skoda Superb 2 model, produced from 2008 to 2015, you can use two methods. The first is to use the multifunction steering wheel. To find out the procedure for carrying out operations, you can see the instructions presented above for cars manufactured in 2008 and later.

The second way is to use the buttons on the windshield wiper switch, if included. Below is a short guide:

Turn the ignition key.
Now you need to find the “Settings” item in the menu. To switch between menu items, click on the upper or lower half of the switch located on the right. This button is used instead of the arrows to move up or down.
To enter, select “Settings” by clicking on the bottom button on the left.
From the submenu that opens, you need to go to the “Service” section.
Select “Reset” and click on the bottom switch located on the left.
Click again to clear the TO memory.
Turn off the ignition.

Is it worth resetting the maintenance?

The “smart” car, Skoda Octavia A7, cares not only about the safety of the people inside, but also about its “health”. The model is serviced every 15 thousand km. As the maintenance date approaches, the car signals its owner that it is time to change the engine oil in the power plant. In various car systems, it is necessary to install new filters and other consumables necessary for the normal functioning of the vehicle.

READ Error codes for Priora 16 valves decoding

A warning about the Skoda Octavia A7 inspection service appears on the on-board computer panel in the car. Information appears after passing 14 thousand km. First, an image of a key is displayed on the BC screen. The picture will remain lit for 10 seconds. On the display, the driver will also see information about how many days and kilometers are left before undergoing maintenance.

SKODA OCTAVIA A7. We offer inspection and oil change services.

When the maintenance deadline arrives, the warning duration increases to 20 seconds and the message “Service now!” appears. The inscription will appear regularly on the monitor until the owner of the model performs maintenance and the service center workers reset the oil change for the Skoda Octavia A7.

If you are forced to change the oil ahead of schedule, the reasons for which we described above, when the service interval for the Skoda Octavia A7 is reached, the information message will still persistently remind you of its implementation. The on-board computer does not contain information about whether the technical fluids in the car have been changed or not. The device will still issue messages indicating the need for service.

This will tell you how to reset the oil service indicator on the digital instrument panel of the Skoda Octavia A7

How to reset service on Skoda Yeti

Drivers still often have difficulties with this car. The reason is that Yeti has different configurations, and each one performs interval reset differently. In cars produced after 2013, there is a clock button on the right, and a reset key on the left. Detailed step-by-step instructions for resetting are presented below:

Turn off the ignition.
Press and hold the service interval reset button for 5 seconds.
You must turn the ignition key and then release the switch.
If the screen does not display the inscription, you need to press the key to set the clock.
The program will ask if the data needs to be reset. You need to turn the wheel on the right to about and click on the center.
The TO indicator should reset to zero. The ignition must be turned off and then turned on immediately.
When turned on, the “Service Oil” sign should disappear.

Video showing the interval reset process:

It happens that the service indicator lights up. In this case, operations are performed according to the same scheme, but they are performed with the alarm system turned on. It is necessary to activate the emergency lights before performing any manipulations.

If the model is equipped with a multifunction display, manipulations are performed with the ignition on. The procedure is the same as when resetting the service interval on Skoda Superb and Rapid. In the same way, the user goes to the menu, goes to settings and goes to the “Service” section, which has a reset function. The only difference is that after clicking “Reset” you need to click again to confirm the reset. It is important to press the key quickly, otherwise the data reset menu will close.

Is it worth doing it yourself?

Let's consider the question: is it worth resetting the service interval of the Skoda Octavia A7 yourself?

On the one hand, nothing should irritate the driver while driving. Therefore, these actions are justified, especially since this operation of resetting the oil change on the Skoda Octavia A7 is not particularly difficult. This work will also allow you to save money prepared for visiting a car service center.
On the other hand, if the car is under warranty, a maintenance reset for the Skoda Octavia A7, carried out not by employees of the official Skoda dealership, may become a reason for refusal of warranty repairs and maintenance. Czech manufacturers also warn motorists that when resetting the service interval of the Skoda Octavia A7, the display settings may be lost.

Therefore, the car enthusiast himself must decide whether to reset the Octavia maintenance or to do a similar procedure officially, at the dealer. To make a decision, you need to weigh all the pros and cons and take into account the consequences of such a decision.

Service interval indicator for Skoda Octavia A7

Vasya – diagnostician

In addition, the Skoda Octavia A7 oil change reset can be performed using diagnostic equipment produced by the German concern Volkswagen Group - VAG COM. The Russified version of the program is called “Vasya – diagnostician”.

Using the “cord” included in the package, the device is connected to the laptop.
The program is installed.
VAG COM is connected to the Skoda Octavia A7, the ignition is turned on.
The software starts on the laptop screen, you should go to the “settings” menu and select the “test” item.
When working correctly, a message appears on the screen indicating that there is a connection between the device and the machine.

Further work is performed as follows:

selecting the “17-Instruments” mode, switching to “adaptation-10”;
select the “time from inspection” item;
setting the time value – “0”;
the program requests confirmation of resetting the service interval Octavia A7 - the answer is “yes”;
the answer comes that the reset has occurred, then you need to press the “Ok” button and return to the main menu;
To reset the technical inspection message, you must select “Resetting ESI”, click on “Reset”, confirm the action.

After carrying out the work, turn off the device and turn off the ignition.

Standard scheme

We answer the question from the owners of a Czech car about how to reset the service interval on the Skoda Octavia A7. This does not require any tools or skills; even a beginner can perform the reset.

READ Installing a rear view camera for Skoda Octavia a7

Skoda Reset service interval.

You should press the reset button for the kilometers traveled per day with the ignition off. It is located at the bottom left of the car’s speedometer scale on the instrument panel, indicated in the instructions: “0.0”.
While holding the button, turn on the ignition.
The display shows information: whether the oil change counter should be reset. To confirm the operation, you need to press the paddle located under the multifunction steering wheel; the “0.0” button can be released.
Before performing a maintenance reset on the Skoda Octavia A7, you need to turn off the ignition again.
The next step is to turn on the alarm.
Press the “0.0” button and turn on the ignition.
A message appears again about a possible reset of the Skoda Octavia A7 inspection service. Confirm the operation.

Resetting the oil change indicator on the Skoda Octavia A7 is shown in this

Conclusion

When a car is serviced at an official service center, the technicians themselves reset the service interval. If the replacement of consumables was not carried out by the officials, this operation must be performed independently. This operation is extremely simple, and the above methods are suitable for almost every Skoda model. If there are differences in the configuration, you can always look at the instructions for the car and clarify all unclear points.

Sources:

https://blog.maslozona.ru/zamena_masla/sbros-zamenyi-masla-na-skoda-oktavia-a7.html https://remam.ru/raznoe/sbros-servisnogo-intervala-skoda-octavia.html https: //razborov.net/raznoe/reglamentnye-raboty-po-tehnicheskomu-obsluzhivaniyu-shkoda-oktaviya-a7.html https://zinref.ru/avtomobili/Skoda/050_00_00_Skoda%20Octavia_manual_2017_god/012.htm https://autoviber. ru/shkoda-a7-sbros-inspekcionnogo-servisa/ https://avtoskill.ru/remont-obsluzhivaniye/kak-sbrosit-servisnyiy-interval-na-skoda-octavia-rapid-fabia-superb-yeti.html