How to lubricate or replace a generator bearing

The optimal lubricant for car generator bearings is provided by the manufacturer and is designed for the entire service life of the unit. In analogue spare parts, the lubricant is of poor quality, preservative or completely absent. Therefore, in the event of premature wear of a part due to malfunctions and the need to replace it, the question arises: “What kind of lubricant should I lubricate the bearings of a car generator so that they last a long time and do not make noise?”

Since the generator rotor rotates 2–3 times faster than the crankshaft and operates over a wide temperature range, increased demands are placed on lubrication. Read this article about when you need to change the lubricant in the bearings, how to choose it correctly, and what is the best lubricant for generator bearings available in Russia.

How to tell if your generator needs service or repair

Diagnosing problems with PG is quite simple. First of all, their occurrence is indicated by the appearance of extraneous sound from under the hood in the area of ​​the generator - whistling and howling. If the noise intensity increases as the engine speed increases, there is no doubt that there is a problem with the bearings. One possible way to solve this is to lubricate the bearings. The best option is to replace them, especially since the kit is inexpensive (depending on the manufacturer, it will cost up to 3-4 hundred rubles).

But even new bearings can only be supplied with preservative grease. Check their condition and, if necessary, lubricate them to extend the trouble-free operation of the device. However, not every lubricant is suitable for use in such conditions. A car enthusiast needs to know how to lubricate a generator bearing.

Which units are produced in anti-dust versions?

In structures where it is necessary to achieve long-term operation without the possibility of constant forced supply of a slip-supporting composition, models isolated from the environment are used. These are non-separable single-row (ball and roller), double-row, hub, angular contact. In each case, slightly different technical solutions are used. So, if for the first type you only need to make a fastening groove on the outer race, then closed roller bearings have a more complex structure. Due to the fact that the separator in the standard model is located at the level of the ring.

Lubricants and their correct choice

Bearing lubrication is necessary for:

• reducing resistance (friction) when moving;
• partial heat removal and normalization of operating temperature conditions;
• softening mechanical shocks;
• protection against the development of oxidative processes;
• reducing mechanical wear of parts.

Various types of lubricants are used for rolling bearings - liquid and grease. Liquids are quickly produced and squeezed out of parts, and therefore require the organization of constant supply from the outside. For units where it is impossible to organize a constant supply (a car generator is one of these), grease is used in the bearings.

• base oil, which provides the actual lubrication of parts;
• a thickener that gives the lubricant a certain consistency;
• additives to obtain special properties.

To choose the right lubricant, you should take into account the properties of these materials, such as:

• viscosity – determines the possibility of forming an oil film, the thickness of which will ensure optimal operating conditions;
• channeling, which determines the behavior of the lubricant when parts move;
• drop point, reflecting the liquefaction of the lubricant under severe temperature conditions;
• the type of thickener on which most of the properties of the material depend;
• compatibility of additives with operating modes of parts.

Viscosity is the most important characteristic of lubricants. It is this that determines the thickness of the layer of lubricant formed for various shapes and materials of surfaces and bearing performance indicators - load, rotation speed, etc. Viscosity that is excessive for a given operating mode will cause the opposite effect - increased friction and overheating of parts. The optimal viscosity value is determined by the bearing rotation speed and operating temperature. Selection tables are provided in technical literature and on specialized Internet resources. The manufacturer of the bearing and generator must indicate the required value.

The thickener determines such basic properties of lubricants as channeling, water resistance, dropping point, etc. Experts consider thickeners based on lithium soaps to be optimal for PGs and their operating modes. Such auto lubricants are called lithium lubricants.

The dropping temperature must be significantly higher than the operating temperature of the part. This will protect the lubricant from separation (oil separation) and ensure optimal material behavior.

Types of additives are selected according to the specifics of the work. Their task is to protect surfaces from oxidation and mechanical damage (scuffing), increase the stickiness of oils, etc.

What kind of lubricant should I use to lubricate the generator bearings?

Operators and manufacturers recommend using lithium greases such as Litol-24M, Fiol-2 and its modifications (Fiol-2M, Fiol-2U), Tsiatim-201, Tsiatim-202, Tsiatim-221, LZ-31, LZ-62 and others with similar characteristics.

Litol-24M

Lithium grease allowing operation in the temperature range -40..+120 degrees. It reduces material consumption and provides effective protection against corrosion and wear.

Fiol-2, Fiol-2M, Fiol-2U.

Fiol-2 is a universal waterproof auto lubricant intended for rolling bearings operating under light loads. Fiol-2M has enhanced anti-corrosion, anti-wear and extreme pressure characteristics and operates at temperatures of -40…+120 degrees. Fiol-2U is an automotive lubricant for bearings of various types. Similar to Fiol-2M, but has better antioxidant properties and mechanical stability.

Ciatim-201, Ciatim-202, Ciatim-221.

Tsiatim-201 is a universal auto lubricant with a high level of all protective (against oxidation, corrosion, scuffing, etc.) properties, waterproof. Used at temperatures -60..+90 degrees. Tsiatim-202 has similar indicators, but with an expanded temperature range (-40..+120 degrees). Tsiatim-221 is intended for lubrication of bearings with rotation speeds up to 10,000 rpm. It is used in various industries, including military and space technology. Temperature range - -60...+150 degrees.

LZ-31, LZ-62.

Lubricants for sealed rolling bearings. They are introduced for the entire period of operation and do not require replacement. They have good antioxidant properties, anti-corrosion and anti-wear characteristics. They operate at temperatures of -40…+120 degrees.

How to lubricate generator bearings

Many motorists are interested in the question: is it possible to lubricate a generator bearing? To do this you will have to remove it. The actions are performed in the following sequence:

• loosen the fastening nut and adjusting bolt on the generator;
• remove the alternator belt (if at this moment there is no noise when starting the engine, the problem is in the alternator);
• disconnect the wire from the negative terminal of the battery (to prevent short circuit during operation);
• remove the generator.

After this, you can begin disassembling the device:

• block the rotor (impeller) - a regular screwdriver is suitable for this;
• unscrew the nut and remove the pulley;
• remove the front cover by releasing the latches or unscrewing the nuts on the studs.
• remove the back cover;
• Remove the rotor from the front bearing.

As a result, access to the bearings pressed into the covers opens. They are removed (knocked out), lubricated or replaced with new ones. Assembly is carried out in reverse order.

Video instructions (very clear)

Self-diagnosis

A generator bearing is a device used to ensure that the shaft rotates with minimal resistance. This element receives and also transmits the load from the moving mechanism to other components of the structure.

Before changing the device, it is necessary to diagnose its performance; this procedure is quite simple:

1. First you need to remove the strap from the pulley.
2. Then the car engine starts.
3. If there is no sound or hum after starting the engine, this indicates that the bearings of the device need to be changed.

Generator Bearing Grease

Current to power conversion calculator

Convert how many amperes a kW has online. Calculator for converting current amperes to power watts

The optimal lubricant for car generator bearings is provided by the manufacturer and is designed for the entire service life of the unit. In analogue spare parts, the lubricant is of poor quality, preservative or completely absent. Therefore, in the event of premature wear of a part due to malfunctions and the need to replace it, the question arises: “What kind of lubricant should I lubricate the bearings of a car generator so that they last a long time and do not make noise?”

Since the generator rotor rotates 2–3 times faster than the crankshaft and operates over a wide temperature range, increased demands are placed on lubrication. Read this article about when you need to change the lubricant in the bearings, how to choose it correctly, and what is the best lubricant for generator bearings available in Russia.

How to choose a good lubricant for generator bearings?

To determine which lubricant to use for car generator bearings, you need to study its properties and check its suitability for the conditions in which it will operate. Key characteristics are:

• Maintaining viscosity at different temperatures . Since the bearing operates in a wide temperature range - from -50°C during winter starting in cold regions and up to +120°C during rotor rotation, a good lubricant for car generator bearings should not harden when cooled and leak when heated.
• Additive content and type . The lubricant must contain preservatives (preserving its properties for a long time), anti-corrosion and extreme pressure additives.
• Resistance to washout . The lubricant must be resistant to water, which may enter the generator, and be minimally washed out by it.
• Drop point . This is a measure of the temperature at which the lubricant becomes liquid enough to start dripping. The higher the point, the higher temperatures the composition can withstand. For high-speed bearings, the dropping point is not lower than 150 degrees Celsius.
• Chemical resistance . During operation at high temperatures, the ingredients of the lubricant composition should not decompose and form oxides. These processes cause a rapid loss of lubricating and protective properties, so the lubricant for car generator bearings must be chemically stable.

Specialized bearing lubricant

Universal lubricants rarely satisfy all of the above requirements at once. A specialized lubricant designed specifically for use in medium- and high-speed bearings shows the best results. Therefore, when choosing what to pack a generator bearing with, you should look towards narrow-profile lithium-based products with a polyurea thickener with a viscosity class of NLGI-2.

An incorrectly selected lubricant will quickly lose its properties and lead to premature bearing failure. Increased belt wear and excessive fuel consumption cannot be ruled out. Therefore, it is better to immediately determine exactly what kind of lubricant is needed for the car’s generator bearings and apply it, rather than disassemble and service it every 5–10 thousand kilometers.

If the generator is already howling or crunching even when it’s hot, the bearing will soon have to be changed in any case due to high wear. If a new part is in doubt, it is better to remove the factory lubricant and replace it immediately.

Having determined which lubricant is best to lubricate the generator bearings and having prepared it, you need to thoroughly remove the remnants of the old lubricant. Lubricants with different compositions can undergo undesirable chemical reactions, which often lead to the loss of their key properties and rapid wear of balls and rings.

Tips for using your washing machine

Proper use of household appliances is an important aspect in operation. To avoid sudden breakdowns, it is advisable to follow some recommendations:

• Do not load the body of the washing machine;
• There is no pressure on the loading hatch;
• It is not advisable to allow small children who actively use the software buttons unnecessarily to access the device;
• Pets must be kept in close proximity to the device;
• Avoid transfusion;
• Use the device strictly according to the instructions;
• It is not advisable to change the program mode when water has already been collected in the machine;
• Do not rinse the drum with a stream of running water;
• To care for the product, use mild cleaning agents that do not scratch the surface.

Rating of the best lubricant for generator bearings

Special lubricants used for generator bearings cost a little more, but are rarely required and last a long time. Trying to save money by purchasing or using a universal lubricant with a viscosity grade of NLGI-2 can backfire. Mixtures that are not suitable for high loads work worse and are quickly washed out and worn out. Good lubrication for car generator bearings will avoid regular maintenance of this unit. Our rating of popular lubricants will help you choose it.

What not to lubricate car generator bearings

In addition to the best lubricants for generator bearings, we list undesirable lubricant options that are often mistakenly recommended and used for the same purposes:

• Litol 24 is a universal automotive lubricant that is also suitable for bearing units, but loses its properties outside the temperature range of -30 – +120 °C.
• Mobil XHP 222 is a popular and high-quality, but too viscous lubricant that is poorly suited for high-speed bearings, despite frequent recommendations for this purpose.
• Grease No. 158 is the famous blue grease for generator bearings, which was popular in Soviet times, as it was superior to grease and other publicly available grease. Its properties are inferior to modern compounds, so its use is not recommended.
• LZ-31 and LZ-62 are Soviet lubricants, which were similarly good in their time, but are now inferior to specialized lubricants.
• Fiol-2 is similar to Litol-24, but more fluid and designed for parts operating in less aggressive conditions. Therefore, lubricating generator bearings with Fiol is a bad decision.

Remember that under normal operating conditions (city and highway driving) sealed bearings do not require maintenance. They can last until the generator wears out completely. But if the bearings are open or the machine operates in difficult conditions (dirt, off-road), then even good lubricant is washed out and degrades faster . In this case, you need to periodically service the generator bearings or change them if, after lubrication, they soon begin to make noise again.

If lubrication no longer helps, after a short time the generator makes noise again - change the bearings by selecting a part of the required size from a trusted manufacturer, for example, SKF or NSK. In addition to the size of the bearing, its clearances are important. For high-speed units subject to overheating, class CN (normal) or C3 (increased) is needed, since when heated the balls expand and the clearance decreases.

If, for example, you install a bearing with insufficient clearance in a generator, it will quickly become unusable due to increased friction forces when the balls expand.

Possible faults

By what symptoms can you understand that it is time to change the bearings on the generator:

1. The device buzzed. If the generator unit makes noise after starting the engine, then most likely the reason is inoperative bearing devices. It happens that devices hum, and then stop. There is no need to think that the problem has resolved itself; the parts will still need to be replaced.
2. The battery is charging unstably, this is due to problems in the operation of the shaft, in particular, its rotation. This problem can be indicated by a control indicator on the car’s dashboard.
3. The assembly pulley rotates.
4. Bearings should also be replaced if the devices become overheated. Overheating is caused by high friction of worn-out components (the author of the video is the altevaa TV channel).

Briefly about the reasons why these parts may fail:

1. Components have worn out, in particular the rolling element, cage, sealing component or raceway. Many car owners think that if they lubricate the bearing in such a situation, this will solve the problem, but this is not true. Wear cannot be eliminated, so parts will have to be replaced.
2. All bearing elements are initially lubricated during installation. Every car owner who has installed and lubricated parts knows how important lubrication of generator bearings is for the performance of the unit. If for some reason the lubricant is out or its level is insufficient, this can lead to accelerated wear of the part.
3. The reason may also be the rotation of the outer race in the device body on the rotor shaft. This reason is also due to wear and tear of the elements or their defects.
4. Abrasive particles could get inside the structure of the part, this will lead to not only noise, but also squeaking.
5. Belt failure, use of an incorrect or defective belt on the shaft.
6. Pulley imbalance. In case of such a malfunction, you must first find out for what reasons the imbalance occurred, and then solve this problem.
7. Rotating the pulley (video author - Geha Lavbinovich).