How to enable and configure autostart on a Pandora alarm

Pros and cons of this feature

Judging by the reviews of the owners, the automatic engine start option has the following advantages:

• a large number of options for activating the function (SMS messages, key fob, mobile applications);
• simple and quick setup;
• does not require additional maintenance;
• availability at any time of the year;
• the cost of security systems with auto start is not much higher than standard car alarms.

Flaws:

• cold start of the power plant increases wear of parts and reduces the working life of the engine;
• frequent automatic starts drain the battery and wear out the starter;
• fuel consumption increases;
• When the engine starts, the immobilizer turns off, which leads to a weakening of the car's anti-theft protection.

Description and equipment

The Pandora DXL Pro car alarm is a premium anti-theft system. It is designed specifically for installation on class B, C, D machines

Alarm equipment with auto start:

1. A set of wires that will ensure the connection of all modules and devices of the complex.
2. LED indicator. It shows the status of the car alarm.
3. Temperature sensor. With its help, you can connect and configure the option of automatically starting the motor based on temperature.
4. Valet security service mode button. After its activation, the system will operate in an emergency state. This will allow you to turn off the alarm and configure the key fobs.
5. USB cable for connection.
6. Tags designed to identify the car owner.
7. Auxiliary controller plug with wiring.
8. A case for installing tags in it.
9. Limit switch.
10. A special block designed to implement the autorun option.
11. GSM module.
12. Microphone used to listen to the interior.
13. A set of ties for combining and fixing electrical circuits.
14. Main and additional remote control.
15. User's manual for installation and operation of the complex.

The Stal63 channel reviewed the operation of the security system on the Toyota Camry.

How to use the alarm (step by step instructions)

How to set up a Pandora dxl alarm key fob
Before using the alarm, the manual recommends:

• study the instructions;
• install the device;
• study the key fob and the purpose of its buttons;
• Perform programming of the key fob and remote control.

Only after completing the above points can you begin to fully use the security system.

Control key fob

With its help, almost all available functions are activated and deactivated. This is realized by pressing certain buttons or their combinations.

Designation of symbols and buttons on the key fob

Most often, the main feedback control key fob is equipped with five keys and a liquid crystal display. Which buttons do what and their combinations are described in detail in the operating instructions.

For example, the Pandora DXL5000 buttons perform the following functions:

1. activation of security;
2. alarm deactivation;
3. switching between modes and disabling the “Panic” mode;
4. state of the system;
5. special SOS button.

Pandora DXL5000

The Pandora DX50 liquid crystal display has many icons, the designation of which can be seen in the instructions.

Key fob programming

The key fob is recorded in the control unit using the “Valet” service button.

In order to properly configure the control panel, you must complete the following steps:

• Turn off the ignition.
• Turn on the key fob.
• Find the “Valet” button and use it to enter your PIN code. For each digit you need to perform the corresponding number of presses.

Valet button

After entering one value, you must wait for the light signal and only then proceed to the next digit. You have 20 seconds to enter the code.

Some Pandora models have a slightly different programming principle:

– DXL3210; – DXL3000; – DXL1870i.

To register them in the control unit you need to follow these steps:

1. Turn off the ignition.
2. Press the “Jack” button once.
3. All buttons on the key fob are pressed until the display blinks or a sound signal is heard.
4. The recording is considered complete if the alarm beeps once.

Principles of setting up autorun

Pandora security systems allow you to configure automatic engine start via CAN in two ways:

– by timer; – by temperature.

Settings are carried out from the key fob by pressing buttons.

By timer

In this case, in order to automatically start the car engine at a certain time, you need to follow the following sequence of steps:

1. Hold down the power button “F” and press until you reach the “fan” icon.
2. By briefly pressing the shutdown button, you need to enter the autorun settings mode.
3. Select the desired menu using F.
4. The on and off buttons are used to set the setting start time, daily timer and warm-up time.
5. Scroll to the end of the list of possible settings and confirm the changes.

Autorun by timer has been successfully configured. Notifications about engine starting and stopping will be sent to the pager.

By temperature

It is possible to activate engine start based on temperature only if the security system is equipped with an appropriate sensor.

The action algorithm is similar to the setting for triggering by timer:

1. Press F and go to the “fan”.
2. Use the shutdown button to enter the autorun settings and use “F” to click on the desired menu.
3. Use the on and off keys to set the start and stop temperatures when specific values ​​are reached.
4. Scroll to the bottom of the menu and confirm changes.

Valet button

The “Valet” service key, like other security systems, is designed to perform:

– emergency shutdown of security; – programming the control unit; – reset settings.

It is most often located in the fuse compartment. The key itself turns red.

System control by phone

Not all Pandora models support controlling the security system from your phone. To control the alarm, it must have a GSM module.

Models that support cellular monitoring include:

– DXL 5000 Pro; – DX 5200; – DXL 3970 PRO; – DXL 3945 PRO; – DXL 3910 PRO and others.

A complete list of models with a GSM module is available on the official website. You can control the “signaling” using SMS commands or using a proprietary application.

The phone allows you to:

– configure autorun; – remote engine start; – block and unblock the start of the internal combustion engine and others.

Installation of car alarms with work algorithm

Security system installation guide:

1. The control unit with a microprocessor must be installed hidden in the vehicle interior. For installation, it is recommended to select free space behind the instrument cluster; this will ensure a minimum length of wires when connecting. The installation site must be protected from external influences, including high temperatures and humidity. To further protect the device from vibrations during movement, the module can be wrapped in cellophane. It is recommended to place the unit with the block facing down to eliminate the possibility of liquid drops flowing into the “device” along the wires.
2. A transceiver with a built-in antenna is installed on the vehicle window. If the front glass is equipped with a protective film, then to avoid the shielding effect, the transceiver is installed from the rear. The working surface must first be cleaned and degreased.
3. The siren is placed under the hood of the car; for installation it is recommended to choose the place most protected from external influences. Do not install the device near the cylinder head or other metal parts adjacent to it. The siren should be placed with the bell facing down to prevent possible moisture accumulation inside in the future. After installation, you must make sure that there is no access to the device and its wires from under the bottom of the vehicle.
4. The service button is installed discreetly inside the car. It can be placed under the instrument panel and additionally wrapped with electrical tape to disguise the key.
5. Limit switches are installed on the hood, trunk and all doors. The placement of these elements is not allowed in drains or places where moisture accumulates.
6. The temperature controller is installed under the hood of the car. To place it, you should select one of the cooling system pipes. You can fix the sensor on the cylinder head or other metal surface adjacent to it.
7. Shock and tilt sensors are installed hidden inside the car. During installation, it must be taken into account that the consumer must always have free access to device regulators.

Key fob with feedback does not respond to button presses

How to set up auto start on a Starline alarm system

On the market of car alarms with two-way communication, Pandora is represented by the following models: DX-70, 90L, 40, DX-90 B, 50B. It happens that the key fob does not open the doors or respond to key presses. Why does this happen?

1. The switch is turned off. For three seconds. hold down F.
2. The battery has died. Change it.
3. The pager froze. Take the battery out of the key fob for a few seconds and insert it. Check the functionality of the device.
4. The remote control has become untied from the control unit. Re-write the communicator in the security system memory.
5. The machine is parked in an area of ​​active radio interference. Park your car somewhere else.
6. Control module failure. Go to the specialists.

Autorun control

How to set up autostart Sherkhan Logicar 1

Autostart from the key fob (if the system is already configured to work with autostart) is simple: to force start, press and hold the arming button. On cars with a manual transmission, this is preceded by a “soft neutral” procedure, specified in the alarm program either rigidly or configured via DXL Loader. For Pandora DXL 5910, you can prohibit or allow the start of program neutral with the handbrake, and completion - when the driver's door is closed.

Perform autostart from your phone (old Pandora models that do not support working with the mobile application) by calling the number of the SIM card installed in the alarm and dialing commands 123* in tone mode. If the motor is already running at this time, the countdown timer will be reset. To turn off the engine, commands 321* are used. Configure the periodic launch parameters from the key fob through the menu:

Autostart based on temperature is configured here as follows:

• in step 3, enable autostart when the temperature drops below the threshold: S°On;
• in step 4 we set this threshold;
• in step 5 we set the warm-up time.

Autostart to maintain engine temperature is configured as follows:

• in step 6, turn on periodic warming up: SdOn;
• in step 7, turn on automatic muting: P°On;
• in step 8 we set the engine temperature, upon reaching which the engine will be turned off.

Autostart settings via the voice menu are performed in two ways - you can either hold the disarm button on the key fob for 3 seconds after the system answers the call, or turn it on for 1-3 seconds and turn off the ignition. Next, commands 6* are entered in the voice menu, after which the desired item is selected:

1. 1* — autostart by time;
2. 2* — autostart time setting;
3. 3* — autostart by voltage;
4. 4* — setting the autostart threshold voltage;
5. 5* — autostart based on temperature;
6. 6* — setting the autostart temperature;
7. 7* - periodic launch;
8. 8* — setting the launch period.

Please note that the settings here do not exactly duplicate those available from the key fob - the startup frequency can be adjusted from the phone, but you cannot limit the warm-up time by temperature. Something else useful for you:

Something else useful for you:

• How to link a new key fob or phone to a Pandora alarm system?
• Which alarm system is better - Starline or Pandora?
• Setting up auto-start on Pandora alarms

How to enter system programming mode?

Self-programming of the Pandora 3910 alarm system by car owners is not approved by the manufacturer, since this procedure is quite complicated and can make serious changes to the factory configuration.

Programming can be done in several ways:

• using the Valet service mode key;
• via laptop and software;
• using a smartphone on which you must first install a mobile application.

To use the service button, the car owner must know the password. Initially, the complex is assigned code 1111. To program the system, open the doors and press the Jack key four times, between each click you must pause for one second. When you press the buttons quickly, the complex will perceive these actions as a double or triple click. When each digit of the password is entered correctly, the LED indicator will blink once. If the light blinks four times, this indicates successful entry into the setup mode.

If you want to use a computer for setup, you must first download the DXL Loader application onto it. The laptop is connected to the system via a mini-USB cable. After starting the software, a password is entered to enter programming mode. After programming, you just need to turn off the ignition, this will save the configuration.

User BaronKorf spoke about the features of the mobile application, as well as the web monitoring resource from Pandora.

Setup via Pandora Alarm Studio

Autorun is configured in the interface group of the same name.

In more advanced alarm models, the choice of autostart settings is much richer.

The differences of this program are support for Bluetooth connection and work with a proprietary server that provides CLONE technology (creating a software copy of the standard immobilizer chip). However, this program is more complex and, being intended for branded installation centers, will require registration. The simplest registration without confirming your work with an official Pandora partner is possible, but...

Working with modern Pandora control units can be done either manually or via a computer.

— autorun settings; — resetting and recording key fobs and control panels; — equipment diagnostics and so on.

Programming via a running PC is performed by connecting the special cable that comes with the kit to the computer. Through the Pandora DXL Loader or Pandora Alarm Studio application and a simple interface, you can perform all the necessary settings or even diagnose the equipment.

Troubleshooting

If autorun does not work, contact the installation center. Pandora systems (unlike the same StarLine, for example) deliberately do not allow the user to easily access the settings of the system itself, so you can even check them only on LX/DXL systems, only if you have a laptop and only if you have saved it after installation cable provided for programming.

If you get to the central unit, connect to it, and in the case of modern systems, also have an authorized installer account to work with Alarm Studio, then you are unlikely to need articles from the Internet for diagnostics, right?

Thanks to multi-level car protection and signal encryption from interception, the modern Pandora alarm system with auto start is the most advanced security system. High-quality components, coupled with their hardware implementation, allow the “signaling” to be virtually invulnerable to all known types of hacking.

Functions

Car alarm S Pandora DX-50 has the following functionality:

1. Alarm mode. Activating the function allows you to launch a light and sound alert that scares away criminals.
2. User feedback. Car owners regularly receive text messages about the condition of the vehicle.
3. Silent switching to security mode. Allows you to protect your vehicle without attracting unnecessary attention.
4. Automatic resumption of security functions after accidental shutdown.
5. Setting the delay time when the protective mode is activated.
6. Quiet security. When the alarm mode is triggered, the system does not emit sound or light signals. The user receives a corresponding message.
7. AntiHiJack function. Activating this option helps the driver protect himself from robbery.
8. Slave mode. You can control the security system using a standard car key fob.
9. Automatic engine start. The motor can be activated by temperature, user command, or when the voltage in the vehicle's electrical network changes.
10. Two-stage activation of protective functions. When you turn on the security mode, the system requests an individual password.
11. Opening windows using a key fob. The function is implemented in cars equipped with automatic window closers.
12. Remote trunk opening.
13. Determining the location of the vehicle.
14. Turbo timer that turns off the engine after the turbine has cooled.

Advantages and disadvantages

The Pandora DX-50 alarm system has positive owner reviews. The advantages of the anti-theft agent in question include the following qualities:

• the presence of modern sensors that protect up to 10 zones of the machine;
• correct operation in conditions of high and low temperatures;
• automatic start, making it easier to prepare for a trip in winter;
• immunity from radio interference;
• quick response to attempts to steal and damage a vehicle;
• intelligent protection against false positives;
• ease of setup and operation;
• affordable price.

Users consider the only drawback to be the incomprehensibility of some installation recommendations.

Model features

The conversational data encoding algorithm is based on military aviation technology, and the developer claims that such a code will not be broken for at least 15 years, although, seeing the progress of modern hacker inventors, one can argue with this. Although if we talk about older Pandora, up to the 3000th series, then they are already successfully hacked. As you can see, 3700 does not fall into this category.

As a rule, everyone is intimidated by installation, but Pandora coped with this by making the process as simplified as possible, and setting up using a computer is a completely doable task even for a non-specialist.

One of the main features of this model is the operating range of the key fob due to signal power amplifiers, and the latest Pandora simply does not have such amplifiers, and the signal range in them is, accordingly, much lower.

Radio signal range

The 3700i model can communicate with the key fob at a distance of up to 1500-1800 meters, which is quite a lot, and also has an external GSM module that can be placed away from various metal components. Thanks to this module, the system can be controlled using a mobile phone.

Mobile phone control

The base unit of the system is made of very high quality, is protected from moisture and dust, and also has heat resistance from +85 to -40. Of course, this does not mean operating in near-boiling water, it only means that the base unit will be able to operate in conditions of high humidity and is capable of performing its functions in large temperature ranges, although constant temperature changes over a long period of time are harmful to it.

Security system equipment

This model is relatively well equipped, and it is worth noting that it differs from the standard dxl 3700 - it is an improved D074 key fob and a new radio module.

New keychain

Also included in the package for this model are:

• Main unit
• Keychain with LCD display D074
• Additional three-button key fob
• RF module (radio module)
• Microphone
• External GSM antenna
• Radio-controlled locking relay IS-121
• Valet button and LED indicator
• Card with personal code
• Documentation.

Contents of delivery

Setting up autorun from your phone

This option is not available on all Pandora systems. To clarify the availability of the service, you must read the operating instructions.

The number is recorded in the system memory using the following steps:

1. Turn off the system and dial the number of the installed SIM card.
2. After establishing communication, press the system disarming button for three seconds. Alternatively, you can turn on the ignition for 2...3 seconds after connecting with the alarm number.
3. Enter DTMF command 1* and 1*.
4. Enter the main phone number that will be used for setup. When entering, use the form *79** *** ****#.
5. Confirm the number by sending command 1*.
6. The number can be recorded in the alarm unit through a registration entry in the Pandora Alarm Studio program.
7. Any cell phone number can be used for calls (you will need to enter a PIN code when dialing).

You must first remove the launch unlock by phone:

1. Dial the system number.
2. After receiving a response, send command 789* to unlock.
3. Wait for confirmation and hang up.
4. To block, enter command 987*.

To remotely start the engine on the Pandora DXL 3910 system you will need:

1. Make a phone call to the alarm number and wait for connection.
2. Send command 123* to activate the launch system. If the motor is running during a call (using automatic start mode based on time or timer), then the receipt of a call extends the operating time by 10 minutes.
3. Receive return confirmation.
4. To stop the engine, a call and transmission of command 321* are used.
5. You can use a command like DTMF to start over the phone on a Pandora DXL 5000 Pro system.
6. Create an entry in the phone book like 79** *** ****,123*,297*. In this entry, the telephone number recorded in the system is entered in field 79** *** ****, commas indicate pauses in dialing, 123* gives the start command, and 297* ends the telephone conversation. The phone number from which the call is made must be entered in the alarm settings.
7. When using an unregistered number, a call of the form 79** *** ****,1234,123*,297* is used. In this case, an additional PIN code is entered (default 1234).

Possible malfunctions and methods for eliminating them

The following problems may occur:

1. On some instances of Pandora DXL 3000 systems, after arming the key fob display, icons of unlocked doors, an open trunk lid and a shock sensor are activated. Icons work alone or in combinations. When you try to disarm the security, the key fob reports a loss of connection with the main unit. In this case, the second key fob operates normally. The cause of the problem is a problem in the firmware of the key fob module. To determine the firmware version, turn off the device and press the second button. A two-digit number will appear on the screen indicating the version of the program. To correct the situation, it is recommended to replace the key fob.
2. According to reviews from owners of the Pandora DXL 3210i, there was a loss of communication between the key fob and the unit. The indicator flashes red, periodically switching to green. For repairs, it was necessary to rewrite the key fobs and change communication channels.
3. The engine does not turn on in temperature start mode. The reason may be incorrect measurement of temperature parameters by the sensor and prohibition of start-up in the settings.
4. Error in transferring data to the key fob. An example would be an error in reporting a remotely started engine, when the icon of a running engine lights up on the screen, but in fact the engine does not start. This occurs due to incorrect settings when data about the running engine is taken over one CAN bus channel. It is recommended to additionally connect data input from the tachometer or generator.
5. Incorrect data from temperature sensors. Due to the design features, signals from different devices may overlap. It is recommended to set different addressing for each sensor in the configuration parameters. After changing the parameters, start the engine and check the readings. If the procedure does not help, then you should additionally change the addressing settings.
6. Errors in the door lock operation that occur due to CAN bus control. It is recommended to test the locking operation in different operating modes of the vehicle electronics. On some cars, the lock can be operated via an analog bus.
7. Incorrect detection of battery status. Pandora car alarms measure voltage and, if it drops below a certain level, inform the owner or turn on the engine to recharge. When installing and configuring, it is important to set the correct value, which is indicated in the instructions for use. If there is an error in the settings, the system will repeatedly start the engine or send messages to the key fob.
8. Incorrect alarm operation after resetting settings to factory values. Pandora alarms are new generation systems and need to be configured correctly. Problem solving techniques that apply to Starline or Scher Khan products cannot be used on Pandora. After resetting the settings, it is recommended to contact a service station for adjustments.
9. Squeaking of different tones coming from the system blocks indicates a defective voltage converter. To repair, the unit assembly is replaced or the faulty element is soldered. The defect occurred on Pandora 3970 systems in the RF module.
10. Loss of communication between the key fob and the car near cell towers. The reason is the sensitivity of some Pandora systems to over-the-air interference. If it is impossible to unlock the car with the key fob, open it with the standard key and deactivate the security with the Valet key.
11. Pressing the key fob buttons turns on all the characters on the screen (or four digits). This is a sign that the remote control is turned off; to turn it on, you must press the third button (F) for several seconds.
12. The key fob buzzer does not work. The owner needs to replace the battery. If problems continue, it is recommended to replace the device.
13. Problems with the system dialing the owner's phone in alarm mode. This is possible when activating the “voice mail” service on the owner’s phone.
14. It is impossible to reach the alarm number from an additional number. Usually the cause is an incorrectly entered system PIN code.

Why is there no connection between the remote control and the module?

Often, when using the Pandora anti-theft complex (1870i, 3110, 3700, 3100, 3500, 3210, 5100 New, 3900, 1000), the connection between the switch and the system is lost. The following will provide instructions for correcting the causes of alarm failure:

• The battery in the key fob is dead. Install a new one;
• exposure to external radio interference. Park the car in a different location. Check the operation of the alarm;
• The keychain is broken. Repair it yourself or replace it with a new one;
• The control module has failed. Go to an electrician;
• dead battery. Charge it or install a new one.

PROMOTION: SALE OF NEW CAR 2022 PRODUCTION

Unlocking the trunk on a 2011 Toyota Corolla

Since there is no way to unlock the trunk, we organize its opening by analogy using a relay.

Red in the left kick panel - power cable for trunk release

We program one of the additional channels so that a minus appears on it when arming for 5 seconds. This channel controls two relays, with the help of which we organize the folding of the side mirrors on the car. With one relay we break the mirror folding wire (gray), with the second - the mirror folding wire (brown). The first relay supplies plus through the NR contacts to the motors, the second relay supplies minus to the motors through the NR contacts. This scheme works regardless of the position in which you left the side mirror folding button.

Gray – folding mirrors, brown – unfolding mirrors

Description of Pandora alarm

Pandora alarms use a built-in tracking module that allows you to track your vehicle's movement on an interactive map of the area. Information is received continuously and can be used to search for a vehicle in the event of theft.

The Pandora Online Pro application is used for tracking.

Features of his work:

• allows you to calculate average speed parameters, stop locations and other useful information;
• data on vehicle movements over the previous period (up to several months) are stored in the archive;
• The program includes a tool for remote engine stop;
• in case of theft, the owner sends a signal via the GSM network, which is sent to the Pandora control unit and blocks the operation of the car.

The alarm unit records data about the vehicle's movements, regardless of whether the standard battery is connected to the on-board network. The stored information can be read by connecting the unit to a computer or laptop.

Pandora systems are characterized by the use of high-tech control devices. For example, the DXL 3910 PRO comes with an anti-theft key fob model IS-760, which is the owner’s identifier. The system is turned off after remote reading of a code encrypted with the AES-128 protocol, which is transmitted over one of 125 channels at a frequency of 2.4 GHz.

To transmit the code, the tag has a button and a diode indicator that confirms the correct power condition of the device. It is possible to control without pressing a button - in this mode, the security system will turn on automatically when the owner leaves the tag’s coverage area (up to 10 m). When you return to the car, the alarm will turn off automatically.

Setting up auto start on the Alligator alarm system

The Slave mode available in many models allows you to use the capabilities of standard security systems, such as keyless access via a CAN bus with a digital signal or an analog communication channel.

Download Pandora alarm installation instructions for different models in PDF format

You can download service manuals for setting up and managing Pandora car alarms using the following links:

Minuses

The above disadvantages most likely apply to cars with a manual transmission.

• Fuel consumption increases.
• In winter, icing of the exhaust pipe occurs (this occurs due to water condensation that forms in the exhaust system).
• In winter, freezing of handbrake cables or brake pads (when the car is parked in neutral).
• If the car is parked on a slope, the handbrake mechanism is weakened - there is a risk of the vehicle moving spontaneously.
• At the moment the autostart is turned on, there is a threat of vehicle theft, since the security system is turned off at this time.

The car owner, only after meaningfully weighing all the pros and cons of autostart, will be able to decide whether it is worth installing the system on his vehicle.

Automatic car start from a key fob has both fans and opponents. There is controversy surrounding this system. Many car owners refuse this car alarm system, having heard a lot of various rumors and myths that have no evidence.

Myths about autorun:

• Independent movement of the car. The most common myth about autostart. And it is not without reason. A car rollback occurs if the driver leaves the car in gear after stopping. With the installation of this car alarm, you will have to change your habits. Now, after stopping, move the lever to neutral and put the vehicle on the handbrake.
• Freezing of brake pads. This myth becomes a reality only for those car owners who do not dry their brakes after driving in wet weather. This is easier to do than it seems. It is enough to perform several intensive braking. And if this problem does affect you, then a two-liter bottle of hot water will come to the rescue. You pour the fluid onto the rear brakes, and you are ready to go.
• Hijacking. Undoubtedly, a car with a running engine is a tasty morsel for a thief. Therefore, you should not use autostart in deserted places and at a considerable distance from the vehicle.
• Steering wheel locking occurs due to human inattention. This happens as follows: the car owner gets into the vehicle with the engine already running and forgets to insert the ignition key. This, in turn, leads to the steering wheel locking. The solution to this problem is to forcefully turn off the engine before driving.

Any problem with auto start from the alarm key fob can be solved. Therefore, the main obstacle to installing a car alarm is the reluctance of the vehicle owner.

>

How autorun works

The engine in the car is started remotely without a key using a special module. This is especially convenient in the cold season, when it is possible to warm up all engine systems and the interior before a trip. In summer, this option is used to turn on climate control, which will lower the temperature in the passenger compartment of the car.

The Pandora car alarm with auto start and feedback implements several ways to control remote activation of the power plant:

1. Manually from the remote control. You can use the key fob without leaving your home, which is extremely convenient.
2. Sending SMS messages from your phone. This method is well suited for large cities when the car is located at a long distance.
3. Using the Internet. The manufacturer has developed special applications for the convenience of car owners.
4. Automatic start by timer or temperature.
5. From a standard radio key (if the car has a Slave mode).

By temperature

In winter, the temperature of technical fluids in the engine can drop to critical values. Under such conditions, the viscosity of engine oil increases significantly. It will not be able to circulate freely, and startup will be carried out with oil starvation. This leads to increased wear of parts and premature engine failure. Automatic engine start will help to avoid such consequences.

Setting up automatic start based on temperature in the Pandora alarm system is done using a key fob, telephone or Internet services. The coolant temperature in the engine is measured by a special sensor. The user independently sets the indicator, upon reaching which an automatic launch will occur. The engine will idle until the temperature rises to operating levels.

By timer

There are several options for programming an alarm with auto start. Using a timer, the time by which the power plant should be warmed up is set. You can set the function so that the engine starts periodically after some time has passed after it has been stopped (for example, after 1, 2 or 3 hours). The engine will automatically shut down when the coolant temperature reaches the set values, or after a user-specified time has elapsed.

If you want to start your car at the same time every day of the week, you can turn on the alarm function. This option will be convenient for people with a tight work schedule. The engine will start at the set time of day, warm up to operating temperature and stop automatically. If the engine fails to start, the alarm will notify the owner about this with a message on the key fob display and a sound signal.

How to program the key fob?

Programming the key fob and some of the functions of the Pandora DXL 3000 system is performed by selecting icons on the display. The security system comes with key fobs that are completely ready for use. The main unit is turned on and off by holding down button 3 for 3 seconds.

Location of buttons and indicators on the Pandora DXL 3000 control panel

Possible settings for the Pandora DHL keychain:

1. To configure the buzzer, use the icon with the text “Mute”. The signal is turned off by button 1, connected by button 2. With silent functionality, the icon goes into flashing mode.
2. When installing an additional immobilizer types IS 471/475/477/577, the “Hands Free” function can be activated. To do this, first “click” the service icon, holding down button 1 turns on the “Hands Free” mode icon. The parameter value is selected with key 2, the selection is confirmed by pressing the first one. The “Hands Free” option allows you to automatically arm and disarm the security system when a special tag (from the immobilizer kit) is detected within range.

Since dialogue encoding is used to transmit signals, the only method for opening the complex is programming an additional key fob. A similar operation is possible when transferring a car with a set of keys to a car service center or to a technical inspection point. Therefore, it is not recommended to give away the remote control along with the keys; if you try to program an additional device, the main switch will stop controlling the complex. After this, you will need to re-register all standard key fobs during 1 session.

To control the number of key fobs programmed into memory, the following technique is used:

1. Disconnect and reinstall the negative terminal of the battery.
2. Carefully count the number of short signals sent by the siren, which corresponds to the number of remote controls in memory.
3. Additionally, you can check their number by the orange flashes of the control diode. To do this, you need to disable the security and turn the key in the ignition switch to the On position.

It is recommended to regularly monitor the number of programmed key fobs, which further increases the anti-theft resistance of the Pandora DXL 3000 complex.

Features of servicing and working with the Pandora switch are shown in a video filmed by Sergei Maslov.

Setting the clock

Algorithm for setting the hour value on the Pandora DXL 3000 key fob:

1. By quickly pressing button 3 of the main key fob, select the shortcut responsible for programming the time. The 4-digit numeric field will then flash.
2. Use button 1 to set the number of hours, and button 2 to set the minutes. Short presses are used, values ​​are switched forward only. If you press and hold the button, the fast scrolling mode is activated.
3. You can exit the clock settings section and start setting the alarm by pressing button 3. To complete the settings, use a long press; the procedure automatically stops after 10 seconds. peace.

Procedure for setting the time in the Pandora DXL 3000 key fob

Setting an alarm

To program an alarm clock in the Pandora DXL 3000 key fob you need to:

1. By pressing key 3, select the alarm clock icon (bell). After this, the label goes into flashing mode, and the text On or Of is displayed in the time display field. You can select a value using button 1 or 2, respectively.
2. Press 3 to go to programming the on time. After this, the number field and the mode icon will start flashing. You can set the alarm value using an algorithm similar to setting a clock.
3. The setup mode is exited automatically or by long pressing button 3. You can verify that the device is active by the bell indicator being on. When triggered, the icon flashes; interruption is carried out by pressing any key on the control panel.

Procedure for programming an alarm clock in a Pandora DXL 3000 key fob

Pandora range

Before getting started with the issue of using an alarm system from the Pandora company, you need to consider the range, which includes devices of both budget and premium class.

• Pandora Deluxe (1870i, 1800, 1870, 2000, 2100) is considered the best model in this class. It has a durable body, several communication channels, an autostart function and an information display on the key fob.
• Pandora OXL (3000, 3950, 4300, 3210, 3500, 3910, 4040), and in particular 5000 New, which also has the function of intercepting and encoding signals from a key fob, remote control, car application. The alarm system is connected using a digital CAN bus.
• Pandora LX (3055, 3297, 3290, 3257, 3030) has features such as the ability to control from the remote control, and the modules come without detachable connections.

Some devices are equipped with a GSM system, which allows you to track your vehicle via satellite communication. This technology guarantees safety and the ability to quickly find a car in unexpected situations.

New Pandora alarm models with auto start

For high-level alarms, autostart support is the norm, so it is not surprising that most Pandora systems currently sold allow the owner to remotely start the engine. Moreover, their advantage is support for cloning standard immobilizer chips using alarm systems without additional crawlers thanks to the multifunctional IMMO-KEY port.

Ways to control autorun:

1. For systems with a classic radio key fob: from buttons.
2. For systems with telematics support: via SMS, voice menu, mobile application.
3. For slave systems: from a standard radio key (the car must initially support this starting method).