VAZ drainage holes - why they are needed and where they are located. I'll show you with examples


The VAZ-2107 car was produced from 1982 to 2014.
Here are colored wiring diagrams (for the injector and carburetor) with a description of all the elements for various modifications. The information is intended for self-repair of cars. Electrical circuits are divided into several blocks for ease of viewing via a computer or phone; there are also circuits in the form of a single picture with a description of each element - for printing on a printer. The “sevens”, like most modern cars, use a single-wire circuit for supplying electricity to electrical equipment. The other terminal of the consumer is always connected to the ground of the machine to which the negative terminal of the battery is connected. This solution allows not only to simplify the design of the on-board network, but also to slow down corrosion.

Design and features of the VAZ 2107 injector

General view of the engine compartment of the VAZ 2107. It is immediately clear that there is no distributor and carburetor.
The VAZ 2107 was not always “injected”. For many years the engine was carburetor. Only since 2006, for the production of VAZ for the domestic Russian market, the engine acquired a forced fuel injection system. The meaning of those innovations was simple - compliance with already accepted Euro 2 standards, which European cars have complied with for many years. The total power of the unit with the new power system was 50 kilowatts. The characteristics of the engine with the new fuel injection were as follows:

  • Usage mode in the city – 8.5 liters 100 km;
  • Fuel consumption at a speed of 90 mph – 6.9 – 7.0 liters 100 km;
  • Consumption at a speed of 120 mph is about 9.1 liters.

The plant guaranteed these characteristics for the VAZ 2107 injector when using gasoline type A - 95. No other type of gasoline was provided for the calculations. The point of converting from carburetor injection to electronic injection was that constant adjustment and fine-tuning of the injection was not required, as with an injection engine. The device is such that the idle speed indicators do not “float”.

The device shown is a control unit, “microprocessor brains.”

The block takes into account the indicators of those sensors that are necessary for the normal operation of injection injection, namely:

  • Throttle position sensor - the device is a resistor of variable capacity, which depends on the degree of pressing the gas pedal. There is no similar equipment in Zhiguli cars, but there is plenty of radio receivers.
  • Crankshaft position sensor (that is, cylinder operation). According to the readings of this sensor, the operation of the electronic processor is completely synchronized with the crankshaft speed. This is the "reference clock speed".
  • An indicator of the saturation of a mixture with oxygen. This device is located on the exhaust gas pipe, and uses feedback to control the amount of incoming fuel in the mixture, since fuel, when burned, consumes oxygen. The indicators of those processes are completely interrelated. In the figure, the exhaust pipe and sensor are connected by a weld, which means that the exhaust system has most likely been repaired.
  • MAF (mass air flow sensor). It is mounted on the “air” body. Its task is to accurately determine the amount of air that enters the intake manifold, and therefore the characteristics of the combustion mixture.

The sensors described above relate exclusively to the injection system, and they are not available on carburetor versions of the “seven”.

Naturally, “there is no smoke without fire.” Therefore, along with many advantages, VAZ 2107 equipped with fuel injection also has certain “cons”.

Disadvantages of an injection engine;

  • High requirements for fuel quality and octane number;
  • The catalyst installed “under the bottom” of the car significantly reduces the ground clearance, depriving the “Seven” of some off-road advantages over the “puzoterki”;
  • More complex engine repairs and difficult access to engine compartment parts.
  • In order to find a malfunction in the injection system, special instruments are needed;
  • In general, the “injector” is more capricious. So, for example, the opportunity to light a cigarette for a friend may result in the engine stalling. The reason is a malfunction of the “electronic brains”.

But the advantages completely compensate for these disadvantages, since injection injection allows you to save fuel, makes cold starting of the engine easier, and there is no need to “tinker” with the carburetor. A car with such an injection will serve you for many years with proper care.

Location of the main components and assemblies of the car

Engine compartment of a car with a carburetor engine: 1 - relay and fuse box; 2 — thermostat; 3 — air filter; 4 — oil filler cap; 5 - engine; 6 — main brake cylinder; 7 — vacuum brake booster; 8 — hydraulic brake reservoir; 9 — hydraulic clutch release reservoir; 10 — expansion tank of the engine cooling system; 11 — EPHH control unit; 12 — windshield washer reservoir; 13 — ignition coil; 14 — radiator cap; 15 — ignition distributor; 16 — engine oil level indicator; 17 — electric radiator fan; 18 — radiator; 19 - battery

Engine compartment of a car with an injection engine: 1 - relay and fuse box; 2 — windshield washer reservoir; 3 - receiver; 4 — oil filler cap; 5 - engine; 6 — fuel filter; 7 — main brake cylinder; 8 — vacuum brake booster; 9 — hydraulic brake reservoir; 10 — hydraulic clutch release reservoir; 11 — expansion tank of the engine cooling system; 12 — air filter; 13 — radiator cap; 14 — ignition coil (module); 15 — engine oil level indicator; 16 — electric radiator fan; 17 — radiator; 18 — air supply hose to the throttle body; 19 — throttle body; 20 - battery

↑ Engine

The car is equipped with a gasoline, four-stroke, four-cylinder, in-line, eight-valve engine with an overhead camshaft.

  • The power supply system is carburetor.
  • The operating order of the cylinders is: 1–3–4–2, counting from the crankshaft pulley.

↑ Differences between VAZ-2103 and VAZ-2106 engines

The VAZ-2103 engine differs from the VAZ-2106 engine in its smaller cylinder diameter (76 mm versus 79) and, accordingly, the cylinder block, the size of the pistons and piston rings, as well as the cylinder head gasket.

The cylinder heads of both engines are the same and their parts are interchangeable. The engine cylinders are arranged vertically in one row and combined into a block.

A block head common to all cylinders is installed on top of it. The bottom of the cylinder block is covered with a stamped steel pan, which also serves as a container for oil.

The pistons have two compression rings and one oil scraper ring. The crankshaft rotates in five bearings in the cylinder block. From the pulley at its front end, a V-belt drive drives the generator and coolant pump located on the right side of the engine.

In the front part of the engine there is a drive for the camshaft and a drive shaft for auxiliary units: ignition distributor, fuel and oil pumps. The drive is carried out by a double-row bush-roller chain.

On the right side of the engine, in addition to the generator, there is an exhaust manifold, starter and intake pipe with a carburetor and air filter. On the left side there is an oil filter.

What is under the hood of the VAZ 2107?

VAZ (Lada) 2107 1982 - 2013

Explain the purpose of the parts under the hood of the VAZ 2107 injector and carburetor. Preferably with a photo.

  1. Accumulator battery;
  2. Windshield washer reservoir;
  3. Relay and fuse box;
  4. Throttle body;
  5. Receiver;
  6. Air supply hose to the throttle body;
  7. Oil filler cap;
  8. Radiator;
  9. Engine;
  10. Fuel filter;
  11. Radiator cap;
  12. Electric radiator fan;
  13. Engine oil level indicator;
  14. Brake hydraulic reservoir;
  15. Air filter;
  16. Clutch release hydraulic reservoir;
  17. Clutch release hydraulic reservoir.
  1. Relay and fuse box;
  2. Accumulator battery;
  3. Air filter;
  4. Oil filler cap;
  5. Engine;
  6. Engine oil level indicator;
  7. Distributor;
  8. Electric radiator fan;
  9. Vacuum brake booster;
  10. Ignition coil;
  11. Radiator cap;
  12. Brake hydraulic reservoir;
  13. Clutch release hydraulic reservoir;
  14. Expansion tank for engine cooling system;
  15. Windshield washer reservoir.

↑ Suspension

To install the engine assembly with gearbox and clutch, a three-point suspension scheme is used. The two front supports are located on either side of the cylinder block and are attached to the cross member of the vehicle's front suspension. The rear support is located on the gearbox and rests on a cross member fixed under the floor of the body.

The elastic cushions of the front supports consist of rubber with vulcanized steel washers and mounting bolts. To increase the rigidity of the supports, there are springs in the central hole of the cushions, supported by insulating rings, and to soften impacts, rubber-metal buffers are located inside the springs. The cushions are attached to the brackets using intermediate plates. The right cushion is protected from heating from the side of the exhaust pipe of the mufflers by a protective casing.

The rear support is also rubber-metal, it consists of three steel plates with rubber separating them. The middle plate is attached to the gearbox, and the outer plates are attached to the cross member of the rear engine mount. Steel spacer bushings are placed between the crossbar flanges to protect the flanges from deformation when tightening the fastening bolts.

Hood cable

With the help of a cable, the force that the driver applies from opening the hood to the lock is transmitted. There are often cases when the cable needs to be replaced, here are the main ones:

  • the cable moves with great difficulty in the braid;
  • there was an involuntary break in the wire or cable of the lock drive;
  • the lock or braid of the cable became corroded, which subsequently led to the cable breaking.

How to remove the cable and lock

Necessary tools required when replacing the hood cable:

  • 10mm wrench, if not available, a socket head will do;
  • screwdriver, preferably a flat one;
  • pliers;
  • marker.

Procedure for replacing the cable:

  • remove the clamps that secure the cable to the body. For convenience, use a flat-head screwdriver;
  • using pliers, bite off the cable at the entrance to the braid;
  • remove the cable from the clamp;
  • go to the car interior, use pliers to remove the cable from the braid;
  • in the engine compartment, use a flat-head screwdriver to remove the rubber seal. Then remove the cable sheath;
  • Next, there is a need to dismantle the lock; using a 10mm wrench, unscrew the nearby nuts and remove it.

Installing a new cable

Pass the cable through the hood release handle

We thread the cable into the sheath

Cable sheath seal

  • pass the end of the cable through the hole in the lock and put on the tube;
  • make a loop at the end of the cable by passing the end through the tube;

We pass the end of the cable into the tube

We crimp the tube onto the cable

Video on replacing the hood cable

↑ Cylinder block

The cylinder block is made by casting from special high-strength cast iron. The holes for the cylinders are bored directly in the block and additional inserts (liners) are not used in the cylinders. To obtain a special profile and surface cleanliness, the cylinders are honed. By diameter, cylinders are divided into 5 classes every 0.01 mm, designated by the Latin letters A, B, C, D and E. The class of each cylinder is marked on the bottom plane of the cylinder block.

The holes for the main bearings of the crankshaft are bored together with the bearing caps. Therefore, they are not interchangeable either with each other or with the covers of other cylinder blocks. In order not to confuse the lids, markings are made on them. The bearing caps are attached to the cylinder block with self-locking bolts, the replacement of which with any other bolts is unacceptable.

The auxiliary drive shaft rotates in two bushings pressed into the cylinder block. The front bushing is steel-aluminium, and the rear bushing is metal-ceramic, bronze-graphite. Spare parts are supplied with bushings of nominal and repair sizes with an internal diameter reduced by 0.3 mm.

How to open the hood if the cable is broken

Perhaps the most unpleasant moment that can take the driver by surprise is a broken hood cable. This situation is quite difficult, but quite solvable. Below are the most common options that will help fix this problem:

  • cable break near the lock drive handle. This type of breakdown is considered the most common and also the simplest. To eliminate such a breakdown, you need to use pliers to pull the flexible element and open the lock;
  • if the cable comes off in a place other than near the lock or lever, you can try to remove it through the grille in the hood. Release the hook from the rigid wire, pass it through the grille and pull the lock drive with pliers, this is necessary in order to open the lock. To make this manipulation easier, you need to press the hood down in the area of ​​the locking mechanism;
  • The lock drive can be pulled into the free space between the body and the hood without using the air duct. It is necessary to lift the engine compartment lid as much as possible; you can use a wooden block as a handy aid; it will prevent the hood from returning to its place. To protect the paintwork and avoid damage, wrap a piece of wood in a rag. After removing the cable, you just need to pull it;

Using this hinge you can open the hood

Video about opening the hood with a broken cable

↑ Piston

The pistons are cast from aluminum alloy. To improve its wearability to the cylinder walls, the outer surface of the piston is coated with a thin layer of tin. To compensate for uneven thermal expansion, the piston skirt has a complex shape. It is conical in height and oval in cross section. Therefore, it is necessary to measure the piston diameter only in a plane perpendicular to the piston pin and at a distance of 52.4 mm from the piston bottom.

Based on the outer diameter, pistons (as well as cylinders) are divided into five classes: A, B, C, D and E, every 0.01 mm, and according to the diameter of the hole for the piston pin, they are divided into three categories, every 0.004 mm. The category is indicated by paint on the end (the first is blue, the second is green, the third is red). The piston class (Latin letter) and category (number) are marked on the piston bottom.

Spare parts include pistons of classes A, C, E, which are quite sufficient to select a piston for any cylinder, since pistons and cylinders are divided into classes with some overlapping sizes.

The hole for the piston pin is shifted from the axis of symmetry by 5 mm to the right side of the engine. Therefore, there is a mark on the piston in the form of the letter P for the correct orientation of the piston in the cylinder. The mark should face the front of the engine.

Since 1986, repair size pistons for all VAZ engine models have been manufactured with an outer diameter increased by 0.4 and 0.8 mm. Until 1986, repair size pistons for engines 2103 and 2106 were produced with an increase of 0.4; 0.7 and 1.00 mm.

The pistons of engines 2103 and 2106 differ only in size (diameter).

The piston rings are made of cast iron. Top compression ring with barrel-shaped chrome-plated outer surface. The lower compression ring is scraper type, phosphated.

The piston pins are pressed into the upper head of the connecting rod and rotate freely in the piston bosses. According to the outer diameter, the fingers are divided into three categories every 0.004 mm.

The category of the finger is marked on its end with the appropriate color:

The connecting rod is steel, forged. The lower head of the connecting rod is detachable; connecting rod bearings are installed in it. The connecting rod is processed together with the cap and therefore they are not interchangeable with the caps of other connecting rods. To avoid mixing up the connecting rod caps during assembly, the connecting rod and its cap (on the side) are marked with the number of the cylinder in which they are installed. When assembling, the numbers on the connecting rod and cap must be on the same side.

Fuse and relay diagram 2107

On newer “sevens” a block with 17 fuses and 6 relays is installed. VAZ 2107 fuses on the “new” unit protect the following electrical circuits and devices:

  1. Reversing lamps, heater fan, rear window defroster warning lamp and relay, rear wiper motor and rear washer pump.
  2. Electric motor for front wipers.
  3. Reserve socket.
  4. Reserve socket.
  5. Power supply for heated rear window.
  6. Clock, cigarette lighter, power socket “carrying”.
  7. Signal and radiator fan.
  8. Turn signal lamps in emergency mode.
  9. “Fog lights” and a relay that regulates the voltage of the on-board network.
  10. Instrument panel lamps.
  11. Brake light bulbs.
  12. Right high beam headlight.
  13. Left high beam headlight, high beam warning lamp.
  14. Side lights (rear right, front left), license plate and engine compartment lighting.
  15. Side lights (rear left, front right), glove compartment and cigarette lighter lamps.
  16. Low beam (right lamp).
  17. Low beam (left lamp).

↑ Crankshaft

The crankshaft is cast from high-strength cast iron and has five support (main) journals, hardened by high-frequency current to a depth of 2–3 mm. At the rear end of the crankshaft there is a socket into which the gearbox drive shaft bearing is inserted. The lubrication channels in the crankshaft journals are closed with cap plugs, which are pressed in and caulked at three points for reliability.

To extend the service life of the crankshaft, it is possible to regrind the crankshaft journals when their surfaces are worn or damaged. By grinding, the journal diameters are reduced by 0.25; 0.5; 0.75 and 1.00 mm.

The axial movement of the crankshaft is limited by two thrust half-rings installed in the cylinder block on either side of the rear main bearing. A steel-aluminum half-ring is placed on the front side of the bearing, and a metal-ceramic half-ring (yellow) is placed on the rear side.

The main and connecting rod bearing shells are thin-walled, bimetallic, steel-aluminium. The shells for the 1st, 2nd, 4th and 5th main bearings have a groove on the inner surface (since 1987, the lower shells of these bearings are installed without a groove). The central main bearing shells differ from other shells in that they lack a groove on the inner surface and are larger in width. All connecting rod bearing shells are without grooves, identical and interchangeable. Repair liners are made of increased thickness for the crankshaft journals, reduced by 0.25; 0.5; 0.75 and 1 mm.

Replacing the input shaft bearing of a VAZ 2107

The gearbox on the VAZ classic (which includes the “seven”) is particularly reliable. Often the gearbox “survives” 1-2 engine repairs before it has to be repaired. But sooner or later, her turn comes. One of the gearbox parts that most often requires replacement is the VAZ 2107 input shaft bearing. The reason for its premature failure may be a factory ...

Insulation of VAZ-2107 for the winter

Comfort while traveling by car in winter depends on creating the desired microclimate in the cabin. In winter, it largely depends on the efficiency of the heating system, as well as on how the car is insulated. If we take the VAZ-2107, then the problems with heat in the cabin of this car are quite significant. Design flaws, wear of seals due to long-term use, poor treatment of the interior with heat-insulating materials lead to the fact that the heat simply does not hold in and drafts “walk” around the cabin.

Tuning the rear lights of VAZ 2107

VAZ 2107 is the most popular model among the “classics” of Togliatti automakers. The model began to be produced in 1982. Its production continued at various automobile plants for almost three decades. Initially, the “Seven” was positioned as a luxury variation of the VAZ 2105, distinguished by textile inserts in the interior, seat headrests and modified headlights. In Russia, the VAZ 2107 is still popular, often being...

Interior treatment

To minimize heat loss, you should start from the interior. In the body structure of the VAZ-2107 there are many technological holes, which are closed from the factory with rubber seals. But rubber gets old over time, cracks and the plugs are lost. As a result, cold air begins to leak into the cabin through the technological holes.

Worn insulating materials applied to the bottom, partitions and roof retain heat poorly, so active heat exchange with the outside environment occurs through these surfaces.

All these heat losses significantly reduce the temperature in the cabin, so first of all you need to treat the body. Let us note that insulating the interior is the most labor-intensive and costly work, but without it it will not be possible to obtain good results.

Work on insulating the interior should be carried out before the onset of cold weather. In winter, work will not be carried out as efficiently, since it is difficult to comply with the interior treatment technology.

To process the body, you will have to completely disassemble the interior - remove the trim, seats, floor covering and old worn insulation materials (if any). In general, you need to remove everything from the interior down to the bare metal.

The next stage is to inspect all technological holes, manufacture or purchase rubber plugs for them. This is especially true for the shield separating the engine compartment and the interior.

If corrosion has damaged the metal and led to the appearance of holes in the metal, then welding work is indispensable - the integrity of the body will have to be restored.

Next, the body is treated with insulating materials. The most optimal technology is considered to be the application of vibration insulation, a noise absorber and a layer of heat-insulating material to the surface (bottom, panels, partitions, roof). Three-layer processing provides excellent thermal insulation properties and heat loss will be significantly reduced.

What are the advantages of VAZ 2107 injection models?

• The VAZ 2107 injection engine consumes less fuel. At the same time, it is more powerful than a carburetor engine with the same volume. This is achieved through the optimal formation of the qualitative and quantitative composition of the fuel mixture. Accordingly, the efficiency of an injection engine is higher than that of a carburetor.

• Thanks to electronic speed control, the engine runs more reliably at idle, stalls less when starting, and starts well at low ambient temperatures.

• Compared to a carburetor engine, an injection engine does not require frequent adjustments to the ignition and fuel supply systems.

• The air-fuel mixture that enters the cylinders has the most favorable composition. And the existing catalyst controls the minimum amount of harmful exhaust gases. This plays a big role in preserving the environment and taking care of health.

Modernization and improvement of the stove

While processing the interior, you should immediately check the functionality of the heating system. On the VAZ-2107, the heater design has some design flaws. In addition, over time, the seals of the housing and air ducts cease to perform their function, which leads to the dissipation of the flow of warm air.

The main design flaw in the VAZ-2107 is insufficient fan characteristics (power, number of revolutions). To eliminate this drawback, you can replace the standard electric motor with an electric one. the motor is from a VAZ-2108, but for this you will have to slightly modify the fan housing. But we note that in addition to the motor, you need to immediately change the fuse and rheostat.

A more significant modification is the installation of a VAZ-2108 fan into the stove along with the housing (“Snail”). Such an upgrade will not only provide a powerful air flow, but will also operate more quietly.

When working with the stove, it is worth disassembling the air ducts, cleaning them thoroughly, and putting the structure back together, installing new seals. Additionally, the joints can be covered with insulating materials (the same vibration isolator) to eliminate the possibility of air leakage. The same should be done with the stove body.

If the heat exchanger of the stove warms up poorly, it may require flushing or replacement. The pipes in the interior radiator have a small cross-section, so over time they become clogged with dirt, which greatly reduces heat transfer.

If the radiator is very dirty, it is difficult to wash the dirt out of it, so in such cases it is easier to buy a new one.

How to replace the radiator of a VAZ 2107 stove

The interior heating system of the VAZ 2107 is quite reliable and durable. But, like any unit, it is not immune from breakdowns. Most often, the heater radiator valve fails, the replacement of which is discussed in a separate article. We will look at the signs of a breakdown of the VAZ 2107 heater radiator and the method of replacing it. Signs of a malfunction of the VAZ 2107 heater radiator Malfunction of the heater radiator ...

Door insulation

Good interior sealing cannot be achieved unless the doors are insulated. First of all, all seals should be replaced - on the doors, body pillars, and window frames. These seals are made of rubber and gradually “shrink,” causing heat to escape through the leaks and drafts to form in the cabin. It is not possible to restore the “original” seals; they only need to be changed.

The door itself is also treated with insulating materials and for this they will have to be disassembled. Next, vibration and noise insulators are applied to the internal surfaces, and a heat insulator is applied to the door card.

All these treatments will ensure one of the main conditions for creating comfortable conditions - the tightness of the interior. And modernizing the stove will increase its efficiency.

We put things in order under the hood, as well as in the cabin

Hello everyone
, I’ll tell you what happened to the car. Well, first of all, how the mushrooms appeared, I drove it into the forest in the rain, I didn’t get much

Then I decided to bring the engine into divine shape, for this I bought a valve cover gasket, sealant, a can of primer, I already had paint, well, little things - the heater radiator (mine didn’t leak much), finally new wipers, foil tape, well and LED bulbs for testing.

I don’t remember much about what it was like under the hood.

The drying process has actually already painted quite a few parts.

I ordered new high-quality high-voltage wires for my cars - from Uncle Nail, I think many people know him, especially those who have a carburetor car, I won’t tell you much about them, on wires from 99

That's all for the engine, the wiring under the hood was not much tidied up. It’s getting closer to cold weather here, and winter is coming, but I have nothing on the floor except the trim, so I decided to tackle this issue and dismantled the interior

the floors were treated with mastic, which simplified the task for me) it’s not much clear where the water got under the left rear mat, it turns out

The floors are still on top, to be sure, they were treated with mavilya

I put insulating film on top - there is no money for a normal Shumka!

I replaced the heater radiator, but it leaked on the original gaskets, so it was decided to make homemade gaskets from silicone - thanks to Dad for that.

I put the radiator gaskets on sealant, waited a day, then started it up and checked whether it was leaking or not, everything was clear and dry. I put linoleum with insulation on the isofilm, this was left over from the kitchen - they knew how to do it before

The casing itself

this layer came out

Next I took up the instrument panel, namely the lighting. This is native

And these LED bulbs shine even worse, so I went the other way, I’ll tell you about this a little later, with photos, otherwise I won’t be able to post it here anymore, so for those who are interested, keep an eye out!

Processing the engine compartment

But one more problem remains - the long time it takes to warm up the interior. And to eliminate it, you need to insulate the engine. This will allow the engine to reach operating temperature faster and cool down more slowly.

But it is not possible to insulate the motor itself; there are a significant number of moving elements on it that cannot be covered. But insulation of the engine compartment is allowed.

First you need to insulate the hood of the VAZ-2107. To do this, you can purchase a special cover from the auto store that is attached to the cover from the inside of the hood.

But many car enthusiasts prefer to do this with improvised materials. But when deciding to treat the hood, you should choose the right insulating materials. They must be non-flammable and not absorb oil. Therefore, it is not recommended to use ordinary fabrics.

The engine compartment can be better insulated by gluing insulating materials onto the shield separating the engine from the passenger compartment. But this can only be done by removing the engine from the car.

In addition to the hood, the radiator also needs to be insulated. For this purpose, masks are used that are attached to the radiator grille.

Instead of a mask, you can use a regular cardboard sheet placed between the radiator and the grille. But it is worth considering that you cannot completely close the radiator; heat exchange must still occur. Therefore, a sheet of cardboard should not cover more than 2/3 of the radiator area.

There is no need to take this into account with a mask, since in addition to the grille, there are enough holes in the front end for the air flow to pass to the radiator.

Other front-wheel drive VAZ models

What I like about the domestic automobile industry is that designers do not want to deviate from traditions. Therefore, drainage holes are made in the same places. No matter how the model changes, they do not want to change their traditions. Therefore, holes for draining water are located in the same places: doors, engine compartment, sills.

I hope that with this article I was able to save your body from premature corrosion. Rate the article if you liked it. Write in the comments if you managed to find them on your VAZ cars. Or maybe you know other “secret” locations of drainage holes? - write.

Stylish VAZ-2103 with air suspension, shaving engine compartment and rare DHLA40 carburetors

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]