Setting up autostart in Starline alarms is carried out by the installer himself: it is necessary to configure the algorithm according to how a particular alarm was connected; “training” of the correct idle signal is required. However, often the owner needs to change a number of initial setup parameters - increase the autostart time or set the timer. If any problems arise, we carry out the setup cycle again to make sure that this is not the reason why the car does not start with the key fob. It often happens that an alarm makes the task easier and indicates the Starline error code on the key fob.
As an example of configuration, let's take a common alarm model - StarLine A93. The configuration principles that are described for it are also suitable for other models of this company, and when understanding the principle of autostart operation, we will also understand the alarm systems of other companies.
How to turn off a car using the Starline E90 key fob?
You can turn off the car from the key fob by pressing button “1” for a long time and button “4” briefly.
- Button "1"
- Display information about successful activation of periodic warm-up
- Autostart mode depending on temperature
- Alarm start display
Interesting materials:
Do I need to drain the water from the accumulator? Do I need to drain the first water from the broth? Do you need to drain the water when cooking chicken? Do I need to drain the water after cooking beans? Do you need to salt the water when cooking meat? Do I need to salt the water when boiling potatoes? Do you need to put spruce branches in water? Do I need to drain the water from my humidifier? Should I take Maalox with water? Where does water come from underground?
2. Starline a93 autostart
A93 allows you to start the engine automatically:
- by alarm clock - at a certain point in time;
- by voltage – when the battery voltage drops below the programmed one;
- by interval - after a certain number of hours (2, 4, 6, 8, 10... 24);
- by engine temperature – when the engine temperature drops below the programmed one (-3°C, -6°C, -9°C... -27°C).
The presence of a key fob within the visibility range of the main alarm unit is not required for any autostart.
2.1. Auto start on alarm clock
Before setting up autorun on an alarm, make sure that the time on the key fob is set correctly, the alarm is turned on and programmed for the time you need.
To activate the alarm, move the cursor to the alarm icon
in the manner shown in the figure below.
Now briefly press button 1. One light signal from the car will follow, for five seconds the remaining time until the start of autostart will be displayed on the screen, the alarm icon will light up permanently.
The alarm start time may differ from the programmed time by three minutes.
Autostart by alarm clock is enabled only for one startup cycle. To start a new autorun, you need to activate the icon again.
2.2. Periodic autostart
In this mode, Starline A93 allows you to automatically start the car at certain time intervals - from 2 to 24 hours in increments of 2.
To enable autorun by interval, move the cursor to the watch face icon
in a manner as shown in the figure below.
Now briefly press button 1. One light signal from the car will follow, and for four seconds the current value of the interval autostart will be displayed on the screen (2H - 2 hours, 4H - 4 hours, etc.).
Short presses of button 1 change the value of autorun periods. Each press increases the interval by 2 hours.
When you select the autorun interval you need, press button 1 for a long time or simply do nothing for 4 seconds. The key fob will sound 2 beeps, there will be an icon on its screen
will light up continuously, indicating that automatic interval start is activated.
After a few seconds, the engine will start automatically. You can turn it off immediately or let it run for the programmed time.
2.3. Starline a93 starting by engine temperature
The Starline A93 alarm allows you to autostart based on the engine temperature if it drops below the programmed one. The trigger range is assigned from -3°C to -27°C in steps of 3.
At least one hour passes between two consecutive temperature autostarts. For example, the autostart temperature is programmed to be -20°C. When the temperature dropped below -20°C, the car started, ran for 10 minutes and stalled. 40 minutes after stopping, the engine temperature again dropped below the programmed temperature. But the car alarm will not allow auto-start to occur. The next automatic start will occur only an hour after the car stalled.
To enable automatic start based on temperature, move the cursor to the snowflake icon
in a manner as shown in the figure below.
Now briefly press button 1. One light signal from the car will follow, the key fob will emit a melodic signal and for five seconds the current temperature at which autostart will occur will be displayed on its screen.
Short presses of button 1 change the autostart temperature value. Each press changes it by 3°C.
When you select the autorun interval you need, press button 1 until you hear a beep or simply do nothing for 4 seconds. The key fob will sound 2 beeps, there will be an icon on its screen
will light up continuously, indicating that automatic temperature start is activated.
2.4. Automatic engine start based on voltage
In this mode, the Starline A93 alarm starts the engine when the voltage in the car drops below the programmed one. The voltage can be changed in 0.1V steps from 11.7V to 12.3V.
Just as with autostart based on temperature, autostart based on voltage drop occurs no earlier than 1 hour after the last engine start.
This function is useful when the car owner leaves the car for a long time, for example, when he goes on a business trip. Then there is a high probability that the battery will be discharged and upon arrival from a business trip the car owner will not be able to start the engine due to a dead battery.
To enable the function, follow the steps shown in the pictures below.
Please note that if there is a loss of power the next time the unit is connected, there will be no autostart based on voltage, since the value is reset to 00 00.
2.5. How to disable automatic launches
To disable autostart on Starline A93 by alarm, temperature and interval, move the cursor to the alarm icon
, snowflakes or clock faces in a manner as shown in the picture below.
Then briefly press button 1 on the key fob. A melodic signal will sound, the turns will blink 2 times, and the corresponding icon will disappear from the screen.
To turn off voltage autostart, follow the same steps as when turning it on. Just select the value 00 00.
2.6. Indication of running engine after automatic start
Each autorun mode has its own indication:
- 1 – alarm clock;
- 2 – period;
- 3 – temperature;
- 4 – voltage.
Causes of problems
If the car does not turn off when you press the remote control button, you need to check the condition of the battery. The problem occurs when electronic components are damaged or when using a key fob that is not registered in the complex’s memory. Identical problems occur when operating Starline A91 equipment, which has a similar design. A backup remote control is used to stop the engine. It is allowed to open a running car with a standard key; the security is disabled by entering an emergency code (without a remote control).
If the car starts up and then stalls after some time, then the functionality and accuracy of the temperature sensor readings located under the hood of the car are checked. To check the operation of the automatic start, you need to program the operation algorithm using a timer, or start the motor remotely using the remote control. If the engine stalls, then the correct installation and configuration of the complex elements is checked.
If the user plans to start and stop the power plant using a mobile application, then it is necessary to control the account balance. If there is no money, the operator blocks the forwarding of messages. In this case, the owner must either use a backup number or a standard Starline A91 or A93 alarm remote control.
The Starline A93/Starline A39 alarm capabilities allow you to remotely start the engine. The alarm also has functions for setting autostart based on engine temperature, voltage, interval and alarm clock.
Vertical keychain Starline A93
Briefly about alarms
The Starline A93 car alarm is a new product for 2014, which has a good reliability indicator and an acceptable cost for most car owners. It works remotely from the control key fob, where you can configure various useful options and functions.
This model has a built-in power relay designed to control light signals and central locking. The control key fob has a shock-resistant mechanism and a built-in antenna. The following options have been added to the general alarm functionality:
- 2CAN;
- LIN modules;
- GSM modem;
- GPS module.
This protection system has intelligent autorun and a dialog code that cannot be scanned. Let's take a closer look at which buttons to press to make the settings.
This is interesting: Where are Hyundai cars assembled?
Autostart does not work - the main reasons, problems and their elimination
As a rule, if there is OS7 on the key fob, then the reason why startup is not possible is indicated. Here are the main reasons why the remote engine start does not work or stops working:
- the hood is not closed – the open hood icon flashes;
- Ignition is on – the ignition on icon is lit;
- The parking brake is not engaged, the brake lights at the rear of the car are on, the lever is not in the “Parking” position – the icon is on.
If, during autostart or when trying to remotely start, the message OS 7 (OST) appears on the key fob, then first check that all safety conditions for autostarts are met: the hood is closed, the ignition is not turned on, the brake lights at the rear of the car are not on, program neutral is set for the mechanics (the doors did not open after it) and the handbrake was raised; for an automatic, the gearbox lever is in position P.
SMS commands and voice control
The disadvantage of this method is that in areas with an unstable Internet channel from a cellular operator whose SIM card is installed in the alarm, problems with starting the engine are possible. Therefore, use the more reliable capabilities of the standard GSM channel - by calling or SMS to the phone number of the alarm SIM card.
When you call, the answering machine will work, which will first ask you to enter the PIN code specified when setting up the GSM module from the keyboard (if the call is not made from the main phone). After this, a greeting will sound and an invitation to dial the command code. If you have forgotten the code for the one you need, then press 0 – the robot will list all available commands.
To start the motor, use two commands - 21 and 26. In the first case, the robot will report the success of the start and remain on the line to receive subsequent commands; in the second, after the report, the call will be automatically dropped. The second option makes it possible to use the phone as a control panel by writing the start command in the directory as a telephone number in the format +7ХХХХХХХХХр26 and selecting this entry in the directory or entering it in the speed dial menu.
To turn off the engine, use command 20 in the same way.
Please note that by default, autorun control is available only from the number that is set as M1 in the settings. If you intend to use an additional phone (of another family member), which is set in the settings as M2, then first activate extended access for it using the SMS command 009401.
The launch is controlled via SMS; for this, a command in the appropriate format is sent to the alarm SIM card number:
- For the owner’s main phone: directly specify the command code (21 for starting, 20 for silencing).
- For the M2 phone, if control is allowed: in the format XX00YYYY, where XX is the command code, 00 is the required separator, YYYY is the pin code.
In sixth-generation systems, the syntax of SMS commands has been expanded: to control autorun, use digital and symbolic codes.
- engine start: ENGINE+, D+, D+
- engine shutdown: ENGINE-, D-, D-
Something else useful for you:
The alarm goes off by itself on the car: why does the car alarm constantly turn on spontaneously for no reason and what to do
How to connect a GSM module for StarLine A93?
How to open the trunk using the StarLine A93 key fob: buttons to open the lock from the remote control
Remote engine start
To use the Starline remote start and autostart functions, you need to make the necessary alarm connections to the vehicle circuits (you may have to use the included autostart module).
You also need to program the system to allow autostarts. To do this, in Table 2, program function 1 to options 2 or 3.
1.1. Features of remote and automatic engine starting
You will not be able to start the engine using the key fob and perform autostart if:
- the brake pedal is pressed; the hood is open; handbrake is off; ignition on; Program neutral for cars with manual transmission has not been completed.
When starting automatically or remotely, Starline A93 makes four attempts. If during these attempts the engine does not start, then the “OS7” icon appears on the key fob, if it is within the visibility range of the unit, the key fob itself emits 4 beeps and the car’s light signals flash 4 times.
In fact, this is not OS7 at all, but the inscription OST from the word “stop”. But for some reason, most users think that this is OS 7.
If the remotely or automatically started engine stalls before the end of the programmed time, the Starline A93 will perform another start cycle.
Automatic start by temperature can be enabled regardless of the state of the autostart functions by interval, voltage and alarm.
1.2. Preparation for remote and automatic starting on machines with mechanics
On cars with a manual transmission, it is necessary to perform a special procedure to enable autostart - program neutral. Following this procedure will ensure that the vehicle does not remain in gear after the ignition is turned off.
Failure to program neutral will prevent the vehicle from being started remotely. Any autostarts will also be impossible. In this case, the same OS 7 (OST) will be written on the display of the Starline A93 key fob.
1.2.1. Performing soft neutral
To perform this procedure you must:
- the engine was started; function 12 of programming table 2 has been programmed to one of the values; function 15 of table 2 had the value 1, 2 or 3.
Next, turn on the parking brake and do the following depending on the selected value of the 12th function.
Function values 12
What should be done
Briefly press button 2 on the key fob with the doors closed
Don't do anything
After these steps, if everything is done correctly, the car’s turns will flash 1 time, the LED will light up constantly, and the engine will continue to run. The display will show r99 or r06 (if the turbo timer is enabled).
Now turn off the ignition (if the value of function 12 of table 2 is 2, 3 or 4) and remove the key from the ignition. The engine should continue to run. Get out of the car and close all doors.
If function 15 of programming table 2 is at value 2, the engine will stop. If the value is 3, it will stop after 20 seconds. If it is 1, it will continue to work until Starline A93 is put into security.
Turn on security mode.
If the turbo timer mode is not activated, then:
- the engine will stall; the door locks will be locked; turns or lights will flash once; the siren will croak once; the key fob will emit one beep; information will appear on the display that the security mode is turned on.
The car is ready for auto starts.
If the turbo timer is programmed, then:
- the engine will not stall; the door locks will be locked; turns or lights will flash once; the siren will croak once; the keychain shows:
- that the engine is running; remaining operating time of the turbo timer; that the security mode is turned on.
After the turbo timer runs out, the engine will stall. From this moment the car is ready for remote and automatic starts.
1.3. Starline a93 how to start from key fob
Before starting the engine from the key fob, make sure that:
- for cars with manual transmission, program neutral is provided; on vehicles with an automatic transmission, the gearbox lever is in the “P” position; the handbrake is tightened; the hood is not open.
To remotely start the engine, press and hold button 1 until the second signal from the key fob. This applies to both the main (with LCD display) and additional key fobs. After the signals, release the button.
The key fob will emit a signal and the message ZPUS will appear on the display. After some time, the engine will start and the screen will display the engine operating time - 10 (r10), 20 (r20), 30 (r30) minutes or indefinitely (r99) - and an animated icon of the running engine (smoke).
The engine operating time depends on the value of function 2 of table 2.
If after the first attempt the car does not start, then Starline a93 will make three more attempts. If even after this the car does not start, then the key fob, if it is in the reception area, will emit four beeps and the inscription OST (OS7) will appear on its display. The car will flash four lights.
As long as the engine is running after a remote or automatic start, the remaining operating time in minutes is displayed on the key fob - r14, r13, r12, etc. When one minute remains (r01), the key fob, if it is in sight, will emit two series of four signals.
What to do if Starline A91 autostart does not work
Sometimes it happens that the autorun function does not work. For example, the starter turns the engine, but it does not start. In this case, it is necessary to check the presence of gasoline in the tank, as well as the charge of the battery. In the first case, everything is clear - you need to add gasoline. Secondly, charge the battery.
It is also possible that the engine does not start when cold and even has difficulty starting with the key. In this case, you can set settings that will increase the starter operating time. You can also reduce the interval between startup attempts.
In this case, the key fob displays information and immediately writes an error. To reset the protocol, you need to start the engine again with the key and tighten the handbrake. Then remove the key from the ignition, open the driver's door and activate the alarm again. Usually the car is armed again and the OS7 error simply disappears. However, this is not always the case. If this does not happen, then you need to contact the service center.
The same procedure is required in case of a short circuit or software failure. A hint of such a reason will be the incorrect behavior of the car and the incorrect performance of certain functions. Specialists from a specialized service center can fix the problem and do everything as professionally as possible.
Using telematics: mobile applications, StarLine-Online
The main disadvantage of starting from a key fob is the limited communication radius. In the city, it is impossible to start the engine, even if the car is parked on the other side of the house. Near high-voltage power lines, in industrial zones, “dead zones” of radio broadcasts even arise, where communication problems are noted even in direct visibility at a distance of tens of meters. It is convenient to warm up the car in the parking lot at the airport or train station even before arriving at the place, when the key fob will not “finish off” by definition.
From the third generation of StarLine alarms, their owners have access to control via a mobile application or the Internet portal starline-online.ru, if a beacon is connected to the alarm in synchronous mode (third generation) or a GPS/GSM module is installed in the alarm itself (fourth generation and beyond) ), and the alarm is registered on the portal.
Using the mobile app on your phone, starting is simple - on the main screen, press and hold the “engine” icon. After this, if the start was successful, the icon will light up, and the dynamic “exhaust” indication will indicate that the motor is running. Starting from the fourth generation (where the second version of the telematics protocol is implemented), you will see the temperature of the engine, interior, battery voltage (in the screenshot below the car is disarmed).
Without a smartphone, but with Internet access, use the StarLine-Online portal. The user interface here is similar to what you will see in the application.
