How does the Starline A93 alarm with auto start work?

How to install autostart on Starline A93

It is best to install an alarm system in a specialized service center, where professional technicians will do everything quickly and efficiently. This applies to a greater extent to owners of new foreign cars like the Tiguan 2022, which have a lot of sensors, gauges and other electrical devices. Moreover, it will be inexpensive - in 2017, the cost of installation was about 5,000 rubles.

Rebooting the Starline A91 alarm system

However, on simpler cars, such as the Kia Sportage 3 or VAZ 2114, you can do this yourself without any problems. Some preparation will be required, as well as suitable equipment:

• a set of tools including side cutters, screwdrivers, knives and a soldering iron;
• drill with drills;
• an industrial hair dryer capable of heating temperatures up to 400 degrees Celsius;
• tester for checking quality connections to the bus;
• set of heat shrink tubes.

Before starting work, it is strongly recommended that you study the alarm connection diagram and act in strict accordance with the instructions.

To summarize the above

That's all the simple steps to ensure that the time setting is successful. To exit the “Functions Menu”, you can briefly press button 4 to scroll through the remaining menu items until you exit, or if you do not perform any actions for 8 seconds, the menu will be exited automatically. Setting the time is the initial step for subsequent work with the alarm, and will allow the owner to use functions such as timed start, periodic start, or combine engine control and vehicle safety.

source

Setting up the Starline A93 alarm system with auto start

The car alarm has a wide list of additional features. Moreover, when equipped with a GSM module, you can program the system to send notifications about attempts to break into the car directly to the owner’s phone. Below is a short list of programming functions and their main features.

1. F1 – determines whether autorun is currently active.
2. F2 – parameter responsible for the autorun duration. You can set it up from the key fob within ten minutes to half an hour.
3. F3 – adjust the sensitivity of the shock or tilt sensors. If the JSM module is available, there is also a function to send a corresponding notification to the phone.
4. F4 – starting or starting the motor depending on the temperature. It is for this purpose that the Starline A93 2Canlin kit contains a motor temperature sensor.
5. F5 – enable or disable the security mode when autorun is enabled.
6. F6 – additional light indication if the automatic engine start is working.
7. F7 – options for controlling the central locking in different operating states. The central lock can close immediately after a successful start, after the engine has finished running, or in both cases.
8. F8 – setting function of the blue cable included in the Starline A93 2can 2lin kit.
9. F9 – determination of the starter operating interval. If the launch fails, each subsequent attempt can be made longer.
10. F10 – determination of engine type (gasoline or diesel engine). Necessary for correct operation of the starter and compliance with the eco mode;
11. F11 – options for monitoring engine operation.

How to enable autostart Starline A93

To be able to start autostart from the key fob on a car with a manual transmission, it is necessary to perform program neutral. This will not allow autostart to be activated if the car is in gear. In the case of a machine placed in park or neutral, such a connection is not necessary.

Enabling Starline A93 autorun can be done in two different ways:

• by tightening the handbrake and then turning on the ignition. In this case, it is necessary to disable mandatory arming;
• by pressing a button on the key fob.

There are also three programming options for this option.

How to set autostart by temperature

The first method involves automatically starting the engine based on temperature. To do this you need to do the following:

• place the cursor on the corresponding icon on the key fob (with a thermometer indicator), and then briefly press the first key;
• after a melodic signal sounds and the temperature value flashes, you can set the appropriate parameter by pressing the first button. The range of values ​​is three degrees Celsius;
• To confirm the choice, press the first key for a long time, up to two short signals.

Autostart Starline A93 by voltage

In order to prevent the battery charge from becoming too low when the car is idle for long periods, owners of Starline A93 security systems can activate the low battery autostart function.

This option is activated and configured in the mobile application hosted on the Starline online service. The driver can select any value between 11.7 and 12.3 Volts.

Start on alarm

In the new Starline A93 systems, you can configure automatic start by the clock. You should first make sure that the time on the key fob is set correctly. To execute the program correctly, you must place the cursor on the corresponding clock icon (using the third button). Then you need to press the first button and hear a melodic signal. The time on the key fob should blink, and the car's dimensions should blink once.

Now the corresponding icon is displayed on the remote control, and the system has begun the countdown to autostart. The alarm clock indicators themselves are set in the same place as the clock parameter.

Equipment

The Starline B94 alarm system comes in a special package that facilitates installation of the system on almost all modern cars. Master installers have at their disposal:

• central unit responsible for managing and processing commands;
• main remote control with feedback, equipped with an LCD display with simple icons and four buttons;
• spare key fob without feedback and without display;
• signal receiver;
• alarm LED mounted on the car body or windshield;
• Valet service button;
• cables in the quantity required for installation. The kit includes all the necessary connectors;
• motor temperature sensor;
• tilt and shock sensor;
• alarm operating and installation manual;
• GSM module with a special SIM card;
• relay R2;
• sound siren block.

How to increase the starter operating time during autostart

In case of low temperatures or a slightly weak battery, you can extend the operating time of the starter during autostart.

• turn off the ignition, press the Valet service key 5 times, turn on the ignition. We listen to five siren beeps;
• using buttons 2 and 3 select SF mode;
• press the third key for a long time until the signal is heard, and then one more time, but briefly;
• Using buttons 2 and 3, select function nine. We set its value to 3 or 4. This way the starter will work at its maximum (6 seconds).

Operating instructions for the new key fob

Not long ago, updated remote controls for the Starline A93 car alarm went on sale. They have several distinctive features. Here is a link to the instructions in PDF format, which allows you to familiarize yourself with all the functions of this device.

You may have a keychain with a horizontal arrangement of icons, or maybe with a vertical one. The first ones came complete with signaling devices released before 2022. All modern systems come with vertical icons. The additional key fob is the same in both the first and second cases.

Key rings Starline A93

• short press – a single press of one or two buttons lasting less than half a second;
• long press – press and hold one or two buttons until the key fob beeps;
• double press – press the button 2 times in a row within one second;
• sequential pressing – double pressing of one or different buttons. First, press and hold the button until a sound signal appears, then release this button and briefly press the second (or the same) button.

The table below shows the main commands of the key fobs with feedback, as well as the additional Starline a93 key fob - it briefly shows how to use them.

Basic control commands for Starline A93 key fobs

How to reduce autostart time

In a similar way, this parameter can be reduced.

• With the ignition off, press the service button 5 times and turn on the ignition. The siren will sound 5 beeps and the programming mode will turn on on the key fob;
• use buttons 2 or 3 to select SF mode;
• press and hold button 3 until the sound signal on the key fob sounds, then press button 3 again briefly;
• Using buttons 2 or 3, select the desired function 9, and then lower its value to parameter 1 or 2.

Specifications

Main characteristics of the Starline B9 alarm system:

• carrier frequency - 433.92 MHz;
• radius of signal transmission from the remote control - up to 600 m;
• supply voltage (DC): 9-18 V;
• temperature range of use: from -40° to 85°C;
• current consumption (in security mode) - no more than 15 mA.

The equipment is equipped with a microprocessor control unit that supports interactive coding of control signals. By using the original code, protection is provided against interception and selection of the key by an attacker. When the power is turned off, the central unit remembers the current state. When the power circuits are activated, the device automatically returns to its original position.

Why doesn't auto start work on the alarm?

Sometimes car alarms stop performing autostart functions. The most common reason why a car won't start is simple inattention. Such reasons include the gear being engaged, the door lock not being closed, etc. It happens that the car stops starting due to the fact that the system does not receive the signal well.

In this case, the key fob displays information and writes error OS7. To reset the protocol, you need to start the engine again with the key and tighten the handbrake. Then remove the key from the ignition, open the driver's door and activate the alarm again. Usually the car is armed again and the OS7 error simply disappears. However, this is not always the case. If this does not happen, then you need to contact the service center.

How to enable slave mode on Starline A93

Error codes

If a malfunction occurs and some functions are not performed correctly by the system, an error code is displayed on the key fob. There are several main categories, the presence of which will help determine the root of the problem.

R99. The signal about this malfunction is not an error per se. This code notifies you about the time that the engine will run during autostart or after turning on the turbo timer. A reading of 99 indicates that the engine will run without shutting down.

OS7. This indication indicates that the engine has had four automatic starting attempts (each time with a longer starter running time) but the procedure was unsuccessful. It is necessary to set the correct parameters for autostart (starter operating time, engine type, etc.), check the CAN bus connection to the tachometer, generator or battery (depending on the type of connection). Check the functionality of the standard immobilizer crawler.

SP.

U9N/L9N. A malfunction that indicates problems with the connection to the key fob. A breakdown in dialogue communication can occur due to a malfunction of the connection cable with the antenna, a breakdown of the antenna itself, or a disconnection of the alarm power contact (plus or ground).

Hi/Lo. Engine temperature sensor error. It is necessary to check the wires for oxidation, as well as the serviceability of the sensor itself.

SIA. Problems with Slave mode. First, you can change the battery (perhaps it is causing incorrect communication). The check is also carried out by disabling the Super-Slave mode.

What to do if the remote engine start does not work

It happens that the remote start does not work. The problem may be that the car starts, but then the car stalls and you have to start it again. Among other malfunctions, it is noted that the car twists the starter, and attempts to start remain unsuccessful. In this case, when disarming the problems go away.

In this case, you need to check the signal directly from the key fob, and also try to set up autostart from the mobile application. If the problem does not go away when you start the engine from your phone, then you need to contact specialists for a thorough diagnosis - the fault is most likely in the sensors and other connected components.

Functions

Functions of a security system with auto start:

• giving alarms when triggered;
• informing the owner about an attempt to break into the vehicle;
• turbo timer support;
• additional immobilizer mode;
• 2-stage engine start circuit blocking;
• a secret code is provided to disable the complex without a key fob;
• built-in component diagnostic unit with automatic exclusion of damaged components from security zones;
• protection of a car with a running engine is ensured;
• search for a car in a parking lot is supported;
• remote starting and warming up of the engine;
• protection against over-torque of the crankshaft by the starter is provided;
• display of motor operating time on the display.

Advantages and disadvantages

The advantages of the Starline Twage B9 complex, according to owner reviews, include:

• reliability of design;
• convenient use;
• support for automatic start of the power unit;
• using dialog code to encrypt commands;
• use of a key fob with an information display.

The feedback about the alarm left by users allows us to highlight its shortcomings:

• The kit does not include a siren;
• problems with recognizing feedback signals in parking lots (due to interference);
• damage to the protective glass of the control panel screen;
• There are many low quality fakes on the market (along with other early Starline models, for example, A6 or A9).

Cost of Starline A93 alarm system with auto start

The price of the security system depends on the configuration of the set. For example, in Moscow, Starline A93 costs from 9 thousand rubles, and if there is a GSM module, the cost increases to 13.5 thousand. For other Russian cities, these figures may vary.

Installing the antenna in the right place

The quality of the antenna and its location are the main factors influencing the range of the alarm.

The signal deteriorates if the antenna is installed:

• on metal parts of the body;
• under the instrument panel;
• on the part of the windshield covered with frits (black dots along the edges of the glass), since they contain metals.

It is best to install the antenna in the upper right corner of the windshield with the pin down if there are no heating filaments, and if there are heating filaments, in the lower right corner with the pin to the left.

The distance from the frits and the metal surface must be at least 5 cm, otherwise the signal level will be reduced.

Matching module

How to enable auto start on the Starline A91 alarm system? The model is more expensive in cost. To connect any alarm, you must use a matching module. What it is?

All modern cars have digital wiring arranged using analogue systems. A fee is used to coordinate it with the vehicle. In new car models it is already installed, but in earlier ones you need to install it yourself.

For normal use, knowledge of its purpose is not necessary.

General requirements

Before starting work, you must study the operating and installation manuals. The security system is designed for installation on vehicles with an on-board voltage of 12 Volts. Thus, it cannot be installed on motor vehicles. In principle, this car alarm can be installed on trucks by powering it from one battery and making galvanic isolation from the electrical equipment of the truck using relays for controlled circuits.

At the first stage of work, an installation map is developed. It shows the installation locations of the main units, the location of the wires, the location of the sensors and the blocking relay.

Electrical installation work must be carried out with the battery disconnected. When removing the battery terminals, make sure that the ignition is turned off, otherwise the standard immobilizer may become untied.

When installing alarm units, rigid connections should be used: self-tapping screws, screw connections, or, in extreme cases, glue. Soft suspension of blocks on plastic clamps significantly reduces the reliability of the system. Installation of Starline A93 requires special attention and thoroughness in all installation work.

Security system conductors should be laid in such a way that they do not come into contact with moving body parts, accelerator, clutch and brake pedals, steering column, or heating climate control systems. It is better to lay all conductors in close proximity to the standard electrical wiring harnesses. After completing the electrical installation work and setting up the security system, you can use plastic clamps to combine standard and non-standard wiring into a single clamp, thereby complicating the work of possible car thieves.

The manufacturer recommends bridging additionally installed blocking relays with diodes. This means that medium power diodes are installed parallel to the relay winding, connected in reverse polarity relative to the on-board network voltage.

Results

When the cold weather comes, many drivers are interested in turning on a system such as remote auto engine start or starting in accordance with temperature indicators.

Starline alarms can cope with this function, provided that such a system is properly installed and configured.

For many motorists, information regarding enabling and configuring autostart for their vehicle is not available. There are several reasons for this - a new or leased car.

After reading the article, you can easily ensure that the engine autostart is turned on using the Starline alarm system.

One of the most popular driving mistakes is ignoring the mandatory recommendations that will be required to turn on auto start and close the door of a switched off car manually using the key fob. Now car enthusiasts will be able to take advantage of the knowledge about the procedure for autostarting the Starline A91. The question of how to make autostart on Starline will not be a mystery to them.

The StarLine A94 alarm system, equipped from the factory with a 2CAN module, is the best price option for cars with digital buses, with the exception of those where the body wiring is based on LIN. But since such cars are in the minority, there is no point in focusing on them. The number “9” in the marking indicates support for A94 autostart, which is implemented using an external power control module. However, it can also be used on cars where autostart does not require duplication of power circuits (the “Start-Stop” button is used or the ignition switch serves as a low-current switch, as on the Renault Megane III).