Where is the override button on a tomahawk alarm?

In this article, auto electrician Alexey Molotov answers the question “Where is the override button on the tomahawk alarm?”

Many car owners are wondering where the Override Tomahawk 9010 button is located. After all, it is necessary to use some functions of the anti-theft system and configure them.

The service button is located in a small plastic case and is red. The key crashes into the car's electrical wiring. Placed in a place inaccessible to burglars. Locate the anti-theft control unit. Most often it is located behind the dashboard or under the center console. There is a double black wire coming from the block. At its end there will be a service key. If the alarm was installed independently, then the search will not be difficult.

Override does not work: what to do

Let's look at the reasons why the service key does not function:

the button itself is broken. Install a new one, check the system;
violation of the integrity of the electrical circuit from the control unit to the key. Look for a gap or poor connection. Carry out repairs. Check the button operation;
control unit failure. Contact the service center.

Purpose of Valet mode on Tomahawk alarms

The most important purpose of the Valet mode is that the Tomahawk anti-theft system has a large range of security services.

These services, at the same time, do not always have to be turned on in order for the car alarm system to work more efficiently over a long period of time.

In other words, if a driver leaves his own vehicle for repairs at a car workshop, then this function should be disabled so that workers can carry out a range of necessary work on the car to ensure complete safety when driving on the road surface.

There are other reasons why the Valet system mode should be disabled periodically. For example, if you leave your car in a safe place, in a garage. In this case, there is no need to use a set of security services if you are absolutely sure that your vehicle is safe in a designated location.

Entering car alarm settings

To get to the Tomahawk 9010 settings menu, follow the instructions.

To use the Tomahawk alarm features, as well as make system settings, you need to know where the Override button is located on the Tomahawk.

What is Override in Tomahawk and what is it for?

Where is the button and how can I find it?

How to use the button?

Entering the settings menu

Enabling or disabling protection mode

Comments and Reviews

Registration of the key fob

Linking Tomahawk 9010 remote controls using the service button is done like this.

Activate the ignition without starting the car engine.
Hold "Override" until the siren beeps four times. This means entering setup mode.
Release the service button.
Press the keys on the remote control “Trunk Opening” and “Crossed-out Horn”. The siren will sound once. If a second transmitter is being linked, then you will hear two beeps, etc.
Exit the setup mode by turning off the ignition. You can exit another way, doing nothing for six seconds.

What is Override in Tomahawk and what is it for?

On the Tomahawk 7010, 9010, 9020, 9030 and other models, the Override key is a special button that allows you to control the security complex. With the help of this element, the consumer has more opportunities to control and configure various functions. You can find out more about them in the car alarm service manual, since they may differ depending on the model.

Using the service key, the consumer can independently configure or reprogram the configuration of the security system. Its use allows you to control the basic functions of the alarm system in case of a lost key fob. Using this element, you can activate and deactivate the protective mode.

Photos of buttons from different Tomahawk models are shown below.

Functionality

What is a Starline alarm service button

Communicators can be used to perform basic functions:

turning on the security mode (can be activated together with a siren or without);
removing the security mode;
disabling the additional immobilizer mode;
control of door locking when the key is installed in the ignition switch and the engine is running;
stepwise control of the locks is possible;
control of devices installed on additional channels;
remote start and stop of the engine (according to various parameters);
carrying out the preparation procedure for remote start (procedure of “software neutral”);
checking system status remotely;
control of the trunk lid lock (unlocking separately from the interior doors);
searching for a car in the parking lot;
programming of alarm functions;
remote control of shock sensor sensitivity zones (turning off and on);
activation of Panic and Anti-Robbery modes;
remote connection of service mode;
calling the driver from the car.

Due to the design features of key fobs, the list of functions performed differs.

Where is the button and how can I find it?

Some car owners are looking for the Override service key on the pager, but it is not located here. The fact is that, according to international standards, the manufacturer does not place an emergency button in an accessible place, since it can be used to change the settings of the complex.

The key is made in a small plastic case in red color. It is installed in the vehicle's electrical wiring. The Tomahawk's Override button is usually located in a hidden place so that a criminal cannot find it during a break-in.

To search for a device, you must first find the processor unit of the security system. It is usually installed under the center console or behind the instrument panel. It may be necessary to dismantle part of the interior trim and the dashboard to search. A double black cable extends to the side from the processor unit. Depending on where the button is installed, this wire can be routed in any direction. There will be a key at the end of the electrical circuit. If you installed the security system yourself, then you yourself must remember where you placed the button.

Frequent problems and solutions

Knowing where the Override Tomahawk button is located and how to use it, you can quickly solve issues related to block binding, programming, and other tasks. Difficulties arise only in cases where the car owner cannot find the key or it does not work. The latter option can occur when the product is not connected to the main unit or the wire is damaged. In this case, you need to diagnose it yourself or turn to specialists for help.

Now you know what Override is on Tomahawk and what this button does. In most cases, car owners do not even think about using it and start searching only when any problems arise. If you cannot find the key, you can always contact a service station or specialists who install security systems.

Today, a large number of car owners protect their vehicles in a large number of ways. Some people use paid parking, others park their cars in garages.

But there is another category of drivers who choose the cheapest and relatively safe way - installing an alarm system. Today, the age of high technology, makes it possible to enjoy a large number of privileges that we receive from computer technology products. The most important thing here is to learn to understand these works of computer art.

Now one of the most common car alarms are modifications of products from the manufacturer Tomahawk. And drivers have many questions about the operation of this alarm, and in particular the most important question is the location of the “Override” button and its main purpose. Let's try to understand this topic in more detail.

How to use the button?

Please note that the procedure for managing car alarm settings requires a more responsible approach. It is better for car owners who have experience and skills in carrying out this task to start it. If you make mistakes when programming the Tomahawk security complex with the Override button, this will lead to a malfunction of the alarm system.

Options setting table with button

The most common option is the ability to cancel the speed limit for moving the car in reverse:

To disable this function or remove restrictions, the car owner needs to click and hold the button in this state for several seconds. After this, the consumer must smoothly press the throttle lever. This will disable the lock.
If the throttle lever is already depressed, then you should not press and hold the Override key. This will cause you to lose control of the vehicle.

To enter the Tomahawk car alarm settings menu, follow these steps:

To emergency activate and deactivate the protective mode, do the following:

The ignition is activated. The procedure for turning on the protective mode is carried out with the power unit turned off.
The service key is clicked eight times.
The ignition in the car turns off. In confirmation, the vehicle’s lighting devices will blink once, and the complex’s siren will also play one signal. Twenty seconds after the actions are completed, the protective mode will be activated. During this time, you need to have time to leave the car, turn off all electrical equipment and close the doors. If one of the security zones is turned on after activation of the emergency protection mode, the complex will report this with three flashes of light devices and a triple siren signal. If the driver does not disable the protective mode within 20 seconds after the notification from the system, this will trigger an alarm.
To disarm the car when the pager is not working or lost, you need to turn on the ignition using the key. There is no need to start the power unit of the car.
To disable the function, press the service key four times. After this, the ignition is turned off.

The Tip-Top channel talked about linking new pagers to the Tomahawk security complex.

Linking new key fobs to control the alarm using the Override button is done as follows:

The ignition is activated by inserting and turning the key in the lock. The engine should not be started.
The service key is pressed until the car siren sounds four times. This indicates that the processor device has successfully entered the pager binding mode.
The Override button is released.
The keys on the remote control are pressed in the form of an open luggage compartment and a crossed out speaker. Successful linking of the pager will be indicated by one signal if the first remote control is linked, the second – two signals will be heard, the third – three, etc.
If you do not send signals to the security complex for six seconds, it will automatically exit the setup mode. You can also leave the menu by turning off the ignition.

Peculiarities

New Tomahawk 9010 alarm To begin with, it will be useful for you to learn about the features of the Tomahawk alarm, so let's start with a description of the main characteristics. The features below are described using the Tomahawk X5 car alarm as an example.

To understand how the circuit works as a whole, we first suggest finding out what elements the device consists of:

main module, which is a block;
key fob (the X5 model comes with a key fob with an LCD display);
another key fob, as a backup, is usually not equipped with a display;
shock sensor, works in one of several modes;
The Tomahawk X5 alarm model is also equipped with an antenna through which data is received and transmitted;
temperature sensor;
a fuse that, if the car is opened, will block the engine;
wires that allow connection according to the diagram;
LED light bulb installed in the car interior;
user manual.

The key fob is designed to control car alarms.

In the case of the Tomahawk X5 model, the control option is as follows:

the protective mode is triggered after you press the key fob button;
if necessary, you can configure the key fob so that the security mode is turned on at a certain time (you can correctly determine the functions and configure them using the operating instructions).

Wiring diagram for the Tomahawk anti-theft system As for functionality, Tomahawk alarms generally have the same functions as other standard devices.

Anti-scanner and anti-grabber. Their purpose is to protect the device from digital signal interception. That is, if an attacker tries to intercept the button signal over a wireless network, he will encounter additional protection.
Another useful feature is Mhz autostart. Autostart on the Tomahawk X5 model is equipped with a timer and interior temperature. If the car is equipped with auto start, then the car starts according to the settings that need to be determined in advance.
If the driver forgets to press the key fob button, the system is activated automatically.
Turbo timer. If the car engine is running, then the turbo timer will allow you to set the car alarm with the engine running, while the doors are closed.
Motor blocking. Even if intruders are able to turn off the shock sensor and open the doors, the engine will be blocked, and the Tomahawk X5 alarm key fob will receive a signal about a break-in.
The alarm system is also equipped with a built-in central lock.
The Tomahawk X5 model is equipped with Valet mode. This mode allows you to disable protective systems. This function is relevant if you are sending your car for repairs.
Silent protection option. If an attacker tries to disable the protection, the system will not make sounds. Even if a criminal opens the doors, the alarm will remain silent. The signal will be sent exclusively to the key fob, at which time the attackers will not even realize that the owner of the car knows everything.
Timer, clock and alarm clock. In general, these options are not particularly relevant for alarms, but the developers of the Tomahawk X5 decided to add them.
Don’t worry about the fact that the key fob is universal and opens all cars with such a security system. Each Tomahawk X5 alarm has a specific PIN code that allows you to control the security to disable it.
If necessary, it is possible to connect your steering horn to a siren, which works when an attempt is made to break into the car.
If the safe driving option is enabled, the system will automatically lock the car doors from the start of driving. The doors will only be unlocked after the vehicle has stopped. The door lock option is very useful, since no one is immune from accidents, especially if you have children. The doors will be locked from the inside and the child will not be able to open them (video author - Evgeniy Ignatov).

Where is the Override Tomahawk button located?

The Override button on the Tomahawk 9010, 9020, 9030 or X5 alarm system is a small-sized plastic product equipped with an individual harness. Another name for the element on car alarms is Valet.

The product may be located under the plastic coverings of the instrument panel or center console near the driver's seat.

The user should easily find the Override button; when manipulating the element, the driver must see the signal diode.

The outer key casing looks like a small cylinder made of impact-resistant plastic, which is attached with 2-sided adhesive tape to a plastic panel or metal frame. The key is made of red or black plastic, the element is located in a special hole on the end of the case. The connection harness, equipped with 2 wires, is connected to the central control unit of the security complex using a plug.