We change the cabin filter on a Chevrolet Lacetti with our own hands: where is it located?

Clean air in your car is as important as clean gasoline in your tank. The air conditioner and cabin air filter are responsible for keeping the air clean and maintaining a comfortable microclimate in the cabin. The Chevrolet Lacetti filter element costs a penny, and you should not neglect replacing it. You should also not reuse the filter, since there is a possibility of damaging the air conditioner evaporator. Where it is, how to replace it and what not to do, we will figure it out right now.

Instructions for replacing the cabin filter in a Chevrolet Lacetti

You can replace the cabin filter without removing the glove compartment lid, but you will have to work hard, since the filter cartridge hatch is located below the glove compartment and unscrewing its fastenings without removing the glove box will be very difficult.

• To remove the glove compartment, unscrew the five screws that hold it in place.
• In the photographs you can see the left and right hinges of the glove compartment and the screws that need to be unscrewed.
• After unscrewing everything, carefully remove it, and do not forget to disconnect the contact chips, which are indicated in the photo.

• Now you need to remove the metal cross bar. It is held on by four screws.
• After all the operations performed, we have direct access to the cabin filter hatch, which must be removed. To do this, unscrew the four mounting bolts and pull out the filter, as shown in the photo.
• After removing the Chevrolet Lacetti cabin filter, it is recommended to turn on the blower fan at full power so that all debris comes out of the filter shaft, after which we install a new filter and reassemble everything in the reverse order.

Video on replacing the cabin filter in a Chevrolet Lacetti

Where to buy and how much does a Chevrolet Lacetti cabin air filter cost?

Before you start replacing the Chevrolet Lacetti cabin filter, you need to buy it and this can be done on the Internet. The cost of a filter, depending on the manufacturer and modification, ranges from 250 to 1000 rubles. The Chevrolet Lacetti cabin filter is not a very expensive thing.

The filter element is a very important part of the entire cabin air system. The degree of cleanliness of the air in the cabin and the operating time of components such as the radiator, evaporator and fan depend on it. After all, it is he who purifies the air entering the cabin. The manufacturer recommends changing the cabin filter after 15 thousand mileage, but it all depends on the operating conditions of the car. If the car is operated on dirt roads with high dust levels, then the cabin filter must be replaced at 7 thousand. This will prolong the operation of all parts of the heating system and allow the driver and passengers to breathe clean air even on dusty sections of roads. The Chevrolet Lacetti is equipped with a filter element made of corrugated paper, which traps dust particles and allows only air to pass through. Accordingly, all the dust and dirt remains on it. And with an increase in the amount of dirt on the ribs, the throughput of the entire system decreases. Because of this, both the heater and air conditioner work worse. Also, poor permeability of the system greatly affects the duration of the fan operation, because it has to blow air with increased load.

When to change or signs of a clogged filter

According to the hatchback vehicle maintenance regulations, the replacement air filter element must be replaced every 15 thousand kilometers.

Otherwise - after 12 months of use.

However, the consumable element may wear out in a shorter period of time depending on operating conditions. Frequent travel on country roads, in megacities or industrial cities with a large amount of exhaust emissions negatively affects the condition of the cleaning element. Therefore, the consumable renewal period can be reduced to 5-7 thousand kilometers.

Signs of an air purifier malfunction may include the appearance of various problems that were not observed before. Each of them is associated with filling the filter with dirt and dust, small particles can be as small as 1 nanometer. As a result:

• air is not able to sufficiently pass through contaminated filter openings and enter the cabin;
• ventilation is poorly blown and does not provide cooling in hot weather;
• the stove does not heat well, its operation is accompanied by unpleasant noise;
• windows often fog up because the air duct is not able to maintain the desired atmosphere in the cabin;
• a persistent musty odor appears.

How to change the filter element on a Lacetti

To replace it, you don’t need to contact services; you can do it yourself. To remove it you will need either a shaped screwdriver or a 10mm socket and a couple of minutes of free time.

1. Move the passenger seat all the way back (to ensure easy access).
2. Let's remove the rubber mat and put paper or fabric in its place (when replacing it, debris will spill out of the shaft).
3. Let's crawl under the glove compartment and unscrew the four screws securing the lid (the screws have a notch for a head or a shaped screwdriver).
4. After unscrewing the screws, the cover can be removed freely.
5. The element lever will be visible behind the cover; by pulling it down, we will take out the old filter (do not be afraid of damaging the old element, since after dismantling it is replaced with a new one).
6. After dismantling the old element, you need to clean the place where it stood. It is better to do this with a vacuum cleaner, or, if not available, with a damp cloth.
7. Then we’ll install the new one in place of the old one, observing the direction of flow (there is an arrow on the frame indicating the direction of flow, it goes from the passenger side to the driver’s). It should be installed carefully to avoid damage (it is important to read the instructions for the filter, as the manufacturer gives its recommendations for installation).
8. After replacement, replace the cover and check the operation of the heater in all positions.
9. Then we remove the debris remaining after the repair and move the passenger seat to its normal position.

Replacing the cabin filter on a Chevroltrt Laceti is not very difficult and can be done with your own hands. This will help purify the interior air more effectively and extend the life of all elements of the heating system.

The cabin filter of your Chevrolet Lacetti works tirelessly. It purifies the air passing through it, removing bacteria, dust, insects, pollen, plant pores, lint and more. But this useful work occurs only if the filter is made with high quality and has a free operating life.

Cabin filters produced by good manufacturers strictly adhere to quality standards. A properly made air filter removes up to 90 percent of harmful substances from the air flow passing through it.

The filter must maintain its characteristics for the entire period specified by the manufacturer. In addition, it must still allow clean and fresh air to pass through.

The design of the cabin filter is quite simple. The first layer, usually made of paper, traps large particles with a diameter of over 10 microns. Behind this is an electrostatic layer that stops smaller particles. As an additional option, leading manufacturers install a third layer, which contains activated carbon. This substance, due to its high adsorption, is capable of absorbing even unpleasant odors.

The manufacturer of the Chevrolet Lacetti recommends changing the cabin filter after 15 thousand kilometers . However, if you prefer to drive on dusty or dirty roads, or on polluted streets, then the service life of the cabin filter is reduced. In addition, replacement of the filter is recommended if any part of it is damaged.

The cabin filter unit cover in the Chevrolet Lacetti is located in front of the front passenger seat. In order to gain convenient access to the mounting location, it is recommended to remove the glove box (also known as the glove compartment).

To remove the glove compartment, you need to unscrew the five fixing screws.

Where is the SF Chevrolet Lacetti located?

It will not be possible to find a cabin filter in a Chevrolet Lacetti sedan with the naked eye. It is carefully hidden behind the front panel of the cabin behind the glove box.

The cleaning element is hidden next to the forced ventilation fan. The easiest way to access it is if it is in the passenger seat.

Step-by-step technology for replacing the Chevrolet Lacetti cabin filter

We unscrew the five screws that hold the glove box: The screws that secure the glove box are shown in the pictures below with red arrows. Green arrows indicate the hinges on which the glove compartment lid moves.

After unscrewing the screws, you can remove the glove box. Don't forget to disconnect the two wires that go to the glove box light.

After this, remove the metal plate by first unscrewing the four screws.

We wipe the seat, install a new filter and put the parts back together.

Where is the cabin filter located in Peugeot?

Peugeot 2008

French engineers paid due attention to this detail: the process of replacing the cabin filter is simple and primitive

SF is located under the hood on the right. The seat is covered with a decorative grille and contains two filter elements.

SF in Peugeot 2008

Peugeot 408. Located under the hood. It is necessary to remove the felt covering; the filter is located horizontally in the engine partition.

But getting to SF in a Peugeot 3008 and 5008 is not at all easy. It is located behind the glove compartment, behind the interior heater, in the vertical compartment

It is necessary to remove the lid under the glove box, the lower part of the glove box, and most importantly, carefully release the latch and lower the heating air duct down

What cabin filter is installed on the Chevrolet Lacetti

But they all must fit into the precise dimensions of the cartridge in which this filter will be installed. GM 96554421 filter has dimensions of 223x189x25 mm . Analogues may differ slightly and this is due to the fact that with one filter of average sizes (± 5-7 mm), the manufacturer wants to occupy as large a cross section of the models as possible. The price of the original GM filter is from 500 to 800 hryvnia (

13-20 €). We believe that this is a astronomical price, so we recommend looking at the list of analogues just below.

Carbon or regular filter?

How many people have so many opinions? Some prefer to install regular filters, others use carbon ones. On the Internet you can find quite a few reviews about carbon filters, which supposedly better filter the air and unpleasant odors from the street. But it is worth remembering that a carbon filter is more expensive than a regular one, so when buying a carbon filter at the price of a regular one, be careful, this filter may be a fake.

Where is the cabin filter located and when to change it

The Lacetti cabin filter is installed in the ventilation, air conditioning and heating system cartridge on the right side immediately behind the glove compartment. To replace it, it will be necessary to remove the glove box cover, as required by the Chevrolet Lacetti operating manual. However, with certain skills, you can do without it. The peculiarity of the Lacetti saloon is that it has a plastic frame with cuts on the sides, which allows it to bend in half. This greatly simplifies installation.

Lacetti interior installation diagram

The Lacetti cabin filter should be replaced at least once every 10-15 thousand kilometers, according to the factory’s recommendations. At the same time, experienced owners do not put off replacement and try to complete it as early as possible, and here’s why:

• a dirty cabin filter creates additional load on the electric motor of the heater and ventilation, which reduces its service life;
• The efficiency of the interior cabin decreases quite noticeably by 4-5 thousand mileage;
• a clogged filter contributes to the accumulation of dust and condensation on the air conditioner evaporator, and this leads to corrosion on its body; the evaporator is not the cheapest spare part;
• on the same evaporator a layer of wet dirt forms, and these are ideal conditions for the proliferation of microorganisms and bacteria, which will not be easy to drive out of the air conditioning system;
• a musty, unpleasant odor appears in the cabin.

When to change, what interior to install

To perform scheduled maintenance operations, there are regulations, as well as manufacturer recommendations. According to them, replacing the cabin filter of the Chevrolet Aveo II T300 heating and air conditioning system should be done every 15,000 kilometers or once a year.

Considering that the operating conditions of the car in most cases will be far from ideal, experts advise performing this operation approximately twice as often, in spring and autumn.

Characteristic symptoms:

1. Windows often fog up;
2. the appearance of unpleasant odors in the cabin when the airflow is turned on;
3. deterioration of the stove and air conditioner;

They may make you doubt that the filter element is coping with its tasks and an unscheduled replacement will be required. In principle, these symptoms should be relied upon when choosing the correct replacement interval.

Suitable sizes

When choosing a filter element, owners do not always use products recommended by the car manufacturer. Everyone has their own reasons for this, some say that the original is unreasonably expensive. Some people in the region sell only analogues, so there is a need to know the sizes by which you can subsequently make a selection:

• Height: 35 mm
• Width: 204 mm
• Length: 240 mm

As a rule, sometimes analogues for the Chevrolet Aveo II T300 may be a few millimeters larger or smaller than the original, there is nothing wrong with that. And if the difference is measured in centimeters, then of course it’s worth looking for another option.

Selecting an original cabin filter

The manufacturer recommends using exclusively original consumables, which, in general, is not surprising. They themselves are of good quality and are widely available in car dealerships, but their price may seem overpriced to many car owners.

Regardless of the configuration, on all second-generation Chevrolet Aveos (including the restyled version), the manufacturer recommends installing a cabin air filter, a dust filter with General Motors GM number 13271190 or a carbon filter with General Motors GM number 13271191.

It is worth noting that sometimes consumables and other spare parts may be supplied to dealerships under different part numbers. Which can sometimes confuse those who want to purchase an original product.

When choosing between a dust and carbon product, car owners are advised to use a carbon filter element. This filter is more expensive, but it cleans the air much better.

It is easy to distinguish - the paper filter accordion is impregnated with a carbon composition, and therefore has a dark gray color. The filter cleans the air flow from dust, fine dirt, germs, bacteria and enhances the protection of your lungs.

Which analogues to choose

In addition to simple cabin filters, there are also carbon filters that filter the air more effectively, but they are more expensive. The advantage of coal SF is that it does not allow foreign odors coming from the road (street) to penetrate into the car interior.

But this filter element also has a drawback - air does not pass through it well. GodWill and Corteco carbon filters are of fairly high quality and are a good replacement for the original.

However, in some retail outlets the price of the original second-generation Chevrolet Aveo cabin filter may be greatly inflated. In this case, it makes sense to purchase a non-original consumable item. In particular, cabin filters are considered quite popular:

Conventional dust cabin filters

• MANN-FILTER CU 2442 – technologically advanced consumables from a well-known manufacturer
• BIG Filter GB-9941 – popular brand, good fine cleaning
• TSN 9.7.764 is a good manufacturer with a reasonable price

Carbon cabin filters

• MANN-FILTER CUK 2442 – high-quality and thick carbon coating
• BIG Filter GB-9941/C – activated carbon
• TSN 9.7.765 – normal quality, affordable price

It makes sense to take a closer look at the products of other companies - they also specialize in the production of high-quality consumables for passenger cars:

• Amd
• Bosch
• Denso
• Filtron
• Fortech
• JS Asakashi
• Knecht Mahle
• Kortex
• Masuma
• Miles
• Raf filter
• SCT
• Sakura
• Stellox
• Valeo
• Zekkert
• Nevsky filter

It is quite possible that sellers may recommend replacing the Aveo II T300 cabin filter with non-original cheap substitutes with a much smaller thickness. They are not worth buying, since their filtering characteristics are unlikely to be at the proper level.

Which Lacetti cabin filter is better, prices, articles, characteristics

Most of the cabin filters for the Lacetti are produced in Korea and China. There are several models from Eurasia, the most expensive ones are produced in Europe, unless it is a global company and the brand does not cover Chinese production with a big name (as is the case with Goodwill filters). A table with prices and articles for Lacetti cabin filters is under the spoiler, and we will look at the most popular of them.

1. The South Korean AMD FC22 performed quite well; it is a simple dust filter, costs around 100 hryvnia, has a rigid mounting frame and is installed without any problems.
2. NSP with catalog number 0196554378 , price about 70 hryvnia, with a rigid frame, stable dimensions, a regular dust filter.
3. Finwhale , Germany, catalog number AS605 . Price 120 hryvnia for 2022. It didn’t cause any particular excitement among the owners, but the quality is not much worse than the original GM.
4. AC Delco with article number 19347483 , an American brand, owned by GM, is actually completely similar to the expensive original and, with a price of 130 hryvnia, is a strong competitor to it.
5. Parts-Mall, a global company with facilities in both Europe and China. Article PMC003 , price about 140 hryvnia, good quality, if not China.

These were ordinary dust filters, but there are also carbon filters on sale, which clean the air more effectively, but are somewhat more expensive. However, we discussed cabin filters of different designs and manufacturers in great detail here.

Where is the cabin filter in Lada

Lada Granta, Kalina. The device is located under the hood, closer to the passenger area. To access it, you need to remove the decorative trim located between the windshield and the hood. Under the protective casing there is a purifier located in a horizontal compartment.

Location of the cabin filter on Lada Granta

Lada Priora Here, the cabin air filter is also located in the engine compartment, under the protective cover and insulation. The SF body is placed vertically directly in front of the stove body. To gain access to the cleaner, remove the trim and insulation, as well as the interfering end of the vacuum booster pipe.

Location of the cabin filter on Lada Priora

Lada Vesta, XRAY. The filter is located under the glove compartment, in the area of ​​the front passenger's left foot. They get to it by removing the right (as viewed from the center) lining of the central tunnel. The compartment is in a vertical position.

Location of the cabin filter on Lada Vesta

Until the summer of 2015, Lada Largus was produced without an installed filter, but with a compartment for it. The seat for the SF is located under the dashboard in the area of ​​the front passenger seat at the bottom left. Those. the body is directed towards the front console (towards the driver, to the left). To install, you will have to dismantle the seat (you can try to do it without this, but it will be harder), and cut out a place for the filter element in the plastic plug with a sharp, durable knife

Be careful not to damage the air conditioner evaporator.

Installing a cabin filter on Lada Largus

Niva, Lada 4×4 Urban. The filter is located under the hood, not far from the windshield, in the so-called boot. To access it, just lift the hood.

Installing a cabin filter on Niva 21214

To replace, just touch the compartment cover with your hand and pull out the element. There is no need to remove or dismantle anything.

How to replace the cabin filter on a Chevrolet Lacetti

Before replacing the cabin filter, it is imperative to turn off the power to either the entire car by removing the terminal from the battery or removing fuse F21, which is shown in the photo below. This is necessary so as not to inadvertently close the glove compartment lighting circuit, and at the same time the low beam.

We disassemble the lower part of the glove compartment and disconnect the backlight terminals.

When the fuse is removed, unscrew the four bolts under the glove compartment.

Remove the cartridge cover.

We take out the old filter.

We thoroughly blow out the system (preferably with a vacuum cleaner), and clean out any debris from the cartridge.

We install the new filter halfway, break the plastic frame in half and insert the filter all the way.

We install the cover and throw on the terminal or put the fuse in place. Good luck to everyone and clean air in the cabin.

A cabin filter is used to clean the air taken from the street. It traps dust, pollen and other foreign bodies, and also reduces the amount of harmful impurities entering the car. The cabin filter can efficiently perform its functions only if it is replaced in a timely manner. In this case, compliance with the automaker’s recommendations for choosing consumables plays an important role.

Why did it happen so?

Perhaps the automatic requests do not belong to you, but to another user accessing the network from the same IP address as you. You need to enter the characters into the form once, after which we will remember you and be able to distinguish you from other users exiting from this IP. In this case, the page with the captcha will not bother you for quite a long time.

You may have add-ons installed in your browser that can make automatic search requests. In this case, we recommend that you disable them.

It is also possible that your computer is infected with a virus program that is using it to collect information. Maybe you should check your system for viruses.

If you have any problems or would like our support team, please use the feedback form.

Clean air in your car is as important as clean gasoline in your tank. The air conditioner and cabin air filter are responsible for keeping the air clean and maintaining a comfortable microclimate in the cabin. The Chevrolet Lacetti filter element costs a penny, and you should not neglect replacing it. You should also not reuse the filter, since there is a possibility of damaging the air conditioner evaporator. Where it is, how to replace it and what not to do, we will figure it out right now.

Article number and cost of the original cabin filter and its analogues

The Chevrolet Lacetti, regardless of the size of the power unit, is equipped with the same cabin filter, article number 96554421. The price of General Motors branded products ranges from 600 to 1200 rubles.

The GM filter element has a plastic frame along the contour and has a special protrusion that facilitates installation and removal of the product from its seat. Many drivers note that this feature has a drawback. Due to the protrusion over the edge of the filter, debris sometimes spills out. For this reason, drivers are forced to seal part of the filter with foam rubber.

The General Motors signature filter is made from a specially developed synthetic fiber. It has antibacterial impregnation. It does not allow microorganisms to colonize the surface of the filter element. Thanks to this, the filter reliably serves the entire period prescribed for it and no foreign odors appear from it.

Despite all the advantages of the original GM filter, many car owners prefer its analogues. This is due to the fact that General Motors consumables are too expensive.

The table below shows the catalog numbers and costs of good non-original filters, which are in no way inferior in performance to a GM product.

Table - List of analogues of the Lacetti branded cabin filter.

Which filter to choose - article numbers of originals and analogues

The manufacturer recommends installing original production parts on the model. They are of the required quality and meet the requirements class=”aligncenter” width=”510″ height=”597″

You can find an original spare part in the store using the following article number:

Not all users prefer original parts. This is due to the high price and average efficiency. Also, “original” consumables cannot always be purchased due to their absence in stores.

The article numbers of the most popular analogues are as follows:

Read more: Peugeot Partner rear beam pin

Replacement frequency

According to General Motors recommendations, replacing the cabin filter on a Chevrolet Lacetti is required after 15 thousand kilometers. Car owners recommend reducing the interval to 5-8 thousand km, or installing a new filter element annually before the summer season.

Reasons to reduce the interval between replacements:

• in places where the car is operated, there is sand or other small foreign particles in the air;
• frequent trips in dense city traffic and stuck in traffic jams;
• the route runs along places where plants bloom;
• frequent travel near production with the release of harmful or fine particles;
• operating the machine on unpaved country roads.

How often should I replace it?

The standard replacement period for cars is the interval between two scheduled maintenance, that is, the cabin filter in the Chevrolet Lacetti is changed once every 15 thousand kilometers. However, the operating conditions of the machine can vary greatly - if in winter it works quietly and more, then in summer on dusty roads it can become noticeably clogged for 5-6 thousand.

The filter life especially drops in the fall - leaves that enter the ventilation are retained by the filter and, in a humid environment, remain in the box, beginning to rot. Even after shaking them out, it is not always possible to get rid of the unpleasant odor that literally permeates the cotton cartridge. Fortunately, a new one is inexpensive - well, replacing the cabin filter with your own hands does not take much time.

Description of replacing the cabin filter on a Chevrolet Lacetti

In order to replace the cabin filter on a Lacetti with your own hands, it is recommended to use the instructions below.

• Disconnect the negative terminal of the battery.
• Jumper F must be removed from the interior fuse box. If this is not done, there is a risk of a short circuit. A blown fuse will not only de-energize the glove compartment light circuit, but will also turn off the warning lights on the dashboard and the side lights.

• Remove the glove compartment. To do this, unscrew three fasteners at the top and two at the bottom.

• Support the glove compartment from below and open the lid latch.

• Turn off the glove compartment light by disconnecting the terminal block.
• Unscrew the steel cross member securing the glove box.

• Remove the four screws that hold the filter cover in place.

• Before removing the filter, it is recommended to lay down a film to prevent debris from falling onto the floor.

• Remove the cabin filter. To do this, you need to pull it at a slight angle to the body using a special protrusion. If difficulties arise, you should break the filter element along the break line.

• Blow out dust and debris from the seat and air ducts.

• Install a new filter.

• Reassemble everything in reverse order.

When the sand or air conditioner is running, you may feel weak airflow and an unpleasant odor, and in the cold season, the windows may fog up. This means that it’s time to remove and replace the Chevrolet Lacetti cabin filter yourself. There are 2 ways to do this yourself: without removing the glove compartment and with removal. We will show both options.

You will need: a new cabin filter, a Phillips screwdriver or screwdriver, a 10″ ratchet, and pliers.

Replacing the Chevrolet Lacetti cabin filter with removing the glove compartment

The glove compartment is held on by 5 Phillips self-tapping screws; they need to be unscrewed with a screwdriver or screwdriver.

After we have unscrewed 5 screws, disconnect the terminals and pull out the glove compartment towards you

Unscrew the Chevrolet Lacetti cabin filter bracket.

Next, unscrew the 4 screws of the filter cover.

We pull out the dirty filter and replace it with a new and clean one. Before replacement, the filter cavity can be blown out and vacuumed. Screw everything in reverse order.

Replacing the Chevrolet Lacetti cabin filter without removing the glove compartment

In this article we will talk to you about replacing the cabin filter on a Chevrolet Lacetti. You can decide to replace the filter on your car based on the standard recommendations to change it every 20,000 km. But more experienced craftsmen offer another way: change the filter as it becomes dirty, since most often cars are not operated in an ecological paradise, but on ordinary city streets, where the air is seriously polluted with exhaust, fumes and dust particles.

To decide whether the filter is worn out or can still serve, you will need to remove it. In fact, this is a very simple procedure that can be done without going to official service stations. You will save money and be confident in the quality of the work.

As you understand, the quality of the air entering the cabin depends on the condition of the filter. A dirty filter will release dust and bacteria that will settle in your lungs. Likewise, the dashboard will regularly become covered with layers of dust. Why is this necessary?

First, use a screwdriver to unscrew the 5 screws that secure the glove compartment.

Replacing the cabin filter on a Chevrolet Lacetti. Unscrew the screws.

Then we disconnect a couple of wires that go to the glove compartment lighting and remove it.

Disconnect the wires from the glove box and remove it

Then unscrew 4 more screws on the metal shield.

Unfasten the plate by unscrewing 4 screws

Unscrew the 4 screws on the camera cover

Then we take out the filter and clean the chamber underneath it. We install a new filter, and then do the entire procedure in reverse order.

Watch also a special video dedicated to replacing the cabin filter on a Chevrolet Lacetti:

Air filter for Chevrolet Lacetti J200 Hatchback 1.4 16V 95 HP id18536

After installing the filter and returning the compartment lid to the original one, I began replacing the second filter under the hood. Late reaction, failures, choking are signs of clogging of the cleaning element. Preparatory stage: If necessary, additional lighting, other consumables that need to be changed, and repair kits are used.

The sequence of actions when replacing a Chevrolet Lacetti car is installed on a flat platform, the hood is open, an unobstructed air filter is provided to the engine compartment, the engine is turned off; how to remove the Lacetti air filter housing: If cracks are detected, replace the parts with new ones from stock.

Final stage: Starting the engine, checking the functionality of the unit. By replacing the air filter on your Chevrolet Lacetti yourself, you will restore natural fuel consumption, acceleration dynamics, and increase service life.

Follow the deadlines for scheduled technical inspections.

Air filter Chevrolet Lacetti hatchback 1 4 instructions! In order for the engine of your Chevrolet Lacetti to develop the planned power, it must receive a high-quality fuel-air mixture. Thus, half of the power contribution comes from the quality of the fuel, and half from the quality of the atmospheric air entering the cylinders. A modern car, and especially its engine, is a very complex structure, and like any complex structure, it is quite sensitive to external influences.

Any complex technology can be ruined by simple negligence. So, after a certain period of operation, the air flow filter of your Chevrolet Lacetti ceases to efficiently clean the incoming atmospheric air, and when a critical mass of dirt accumulates, it can begin to throw them into the engine cylinders. It may seem to many car owners that the quality of the air filter does not have an impact on engine efficiency, but in reality this is not the case.

Therefore, their entry can cause harm to the surfaces of the cylinders and the working surfaces of the engine pistons. In order to prevent these troubles, it is necessary to regularly check and, if necessary, replace the filter element that cleans the air entering the engine cylinders. The service life of the filter element, described in the vehicle's operating instructions, can be adjusted depending on the environment.

Guide to replacing the Chevrolet Lacetti air filter You can change the engine air filter on your own, without turning to the help of technical specialists and air filter Chevrolet Lacetti hatchback 1 4 with just one screwdriver and your own hands.

Main functions of the air filter

To take care of you, the air filter on the Chevrolet Lacetti vehicle model is constantly working.

When passing through it, many harmful substances, such as dust, dirt, bacteria and much more, which are contained in the air, are retained in it, thanks to which you can breathe freely and pleasantly in the cabin.

But you should count on such operational efficiency only if the machine is equipped with a high-quality filter, which, moreover, has a sufficient resource, and is not completely forgotten by dust and other substances.

Large manufacturers who care about their reputation use only high-quality materials in the production of filters, so their purifiers fully comply with quality standards.

A filter manufactured in accordance with the technology is capable of stopping up to 90 percent of harmful substances contained in the air flow. A good purifier should effectively prevent the penetration of harmful substances throughout the entire period specified by the manufacturer. At the same time, clean air must also enter the cabin.

Sometimes it’s even surprising that such a simple device in its design performs such an important task - it purifies the air, ensuring people’s well-being. It is quite interesting to take a closer look at the filter design.

The first layer most often consists of paper, the task of which is to hold large particles with a diameter that exceeds 10 microns.

After it comes the next layer - electrostatic, it does not allow smaller particles to pass through.

The third layer is activated carbon and it is a distinctive option for filter models from well-known manufacturers that have earned a good reputation among consumers. This substance has excellent adsorption, which allows such cleaners to absorb unpleasant odors.

Rules for choosing new equipment

A high-quality air element can prevent about 90% of harmful substances and environmental pollutants from entering the cabin. It is important that the design of the air purifier and the framing frame fully correspond to the dimensions of the seat and do not have any damage to its integrity. In Chevrolet Lacetti station wagons, the standard filter size is 223x189x25 mm in length, width and height, respectively.

It is worth noting that in some models of the interior air cleaner there is a place for breaking the frame. This is necessary in cases where the element fits into the grooves only if force is applied. The holes in the Lacetti are small and cannot always accommodate the filter along with the plastic frame.

The filter element for any brand of car is selected based on two alternatives:

• conventional synthetic fiber filters;
• with carbon impregnation.

The first option allows the air purifier to perform basic functions - to protect against contamination in the form of dust, lint and gases. The second option has additional options that will please the driver. The activated carbon included in the composition absorbs harmful substances and unwanted odors from the outside.

During the summer season, it is recommended to install carbon air filters, since during this period various bacteria, foreign odors and contaminants most actively enter the cabin.

When purchasing, it is also important to pay attention to the production of consumables. Its cost does not exceed 1,200 rubles, with the maximum price set for original parts. Manufacturer: General Motors. The original code for the cabin filter is GM96554421. The advantage of the originals is ease of use - the parameters are designed for a specific car model.

However, when looking for budget options, you can pay attention to suitable analogues:

• AMDFC22, the average retail price of which is 150 rubles;
• PARTS-MALL PMC003 – 230 rubles;
• TSN 9718 (TSN Citron) – 120 rubles;
• Goodwill AG628CF – 165 rubles;
• MANN CU 1719 – 600 rubles.

The presented analogues, like the original model, are conventional air purifier options. The cost of carbon filters may exceed the listed prices.

When is it time to change the cabin filter?

Replacing your cabin filter yourself will save you money and, more importantly, time. In addition, by carrying out this procedure independently, the owner will be convinced that the replacement was completed in a timely manner, and also, subsequently, the owner will be able to control the level of contamination.

According to the recommendations of the Chevrolet Lacetti manufacturer, the old filter should be changed after reaching the mileage mark of 15 thousand km. However, it is necessary to take into account the conditions of use of the vehicle.

After all, if the car has to be constantly used in non-ecological areas, in conditions of high street pollution, with dust and dirt constantly getting inside, it will have to be replaced earlier.

The same cannot be said about ecological areas with high humidity or, for example, with a large concentration of trees (taiga), where it can last even for several years. Please note that the cabin filter should also be replaced if one of its components is damaged.

And now in more detail about how to replace it. In the Chevrolet Lacetti model, the wiper unit cover is located in front of the passenger seat. It will be more convenient to get to the mounting location after removing the glove compartment. It is secured with five self-tapping screws; all of them will need to be carefully unscrewed.

Reviews of KUJIWA cabin filters

To calculate the estimate

missing 7 reviews

among 14 manufacturers

I noticed that the windows began to fog up a lot. It was decided to replace the original cabin filter. I bought a carbon filter from the Japanese company KUJIWA. It turns out that you need to insert it not in the way it originally stood with the correct side, but with the opposite side, having first squeezed it into an accordion, and then turned it inside into the correct position. After installation, the glass stopped sweating, the filter is really good.

I bought a Kujiwa brand filter with order number KUK9324. The air in the cabin is clean, I'm happy.

Model KUK805 I took it for a Honda Jazz Gd1 (2002 - 2008). From a pleasant appearance, there is a halogram on the packaging))) The filter looks like it has an interesting coating))) It retains dust and debris well, I recommend)))

Chevrolet Lacetti cabin filter replacement technology

The glove compartment cannot be removed unless five screws are unscrewed. Their location is clearly shown in the photos below; you can find them by the red arrows. In turn, the hinges with which the glove compartment lid can move are indicated by green arrows.

Once you have the screws in your hands, you can pull out the glove compartment, but before that, do not forget to disconnect the wires for its lighting. There are only two of them in this car model.

Four self-tapping screws hold the metal plate in place; to get to the filter, they need to be unscrewed.

After this you will see the purifier seat. Remove the old filter, wipe its location well and install a new cleaner.

Where is the cabin filter located in a Ford?

Ford Focus, Fusion. The cleaner is located under the instrument panel to the right of the accelerator pedal. Remove and move the pedal to the side without disconnecting it from the electrical connector. Next, all that remains is to remove the compartment cover.

Location of the cabin filter in Ford Focus

In the fourth version of the Ford Mondeo, the filter is located to the right of the gas pedal, which is dismantled.

On the Ford Explorer SF, it is located behind the glove compartment, the removal of which is a rather complicated process, where the latches can break. Therefore, they do not remove the glove box completely, but lower it to the lowest position and carry out work to replace the device.

Location of the cabin filter in the Ford Explorer

On Mondeo 5 the element is located directly behind the glove compartment. But in order to dismantle the glove compartment, you will have to remove the side plug of the torpedo, the decorative trim along with the deflector, and only then unscrew the bolts securing the glove box. The purifier cover is located horizontally and can be easily removed.

Ford Kuga 2FL. Compared to the first version, where you had to remove the gas pedal to replace the cabin filter, on the updated compact crossover you don’t even have to remove the glove compartment. It is enough to move the lower trim under the glove box and next to the fuse box you can find the cover of the filter device.

When to change, what interior to install

To perform scheduled maintenance operations, there are regulations, as well as manufacturer recommendations. According to them, replacing the cabin filter of the Chevrolet Orlando I J309 heating and air conditioning system should be done every 15,000 kilometers or once a year.

Considering that the operating conditions of the car in most cases will be far from ideal, experts advise performing this operation approximately twice as often, in spring and autumn.

Characteristic symptoms:

1. Windows often fog up;
2. the appearance of unpleasant odors in the cabin when the airflow is turned on;
3. deterioration of the stove and air conditioner;

They may make you doubt that the filter element is coping with its tasks and an unscheduled replacement will be required. In principle, these symptoms should be relied upon when choosing the correct replacement interval.

Suitable sizes

When choosing a filter element, owners do not always use products recommended by the car manufacturer. Everyone has their own reasons for this, some say that the original is unreasonably expensive. Some people in the region sell only analogues, so there is a need to know the sizes by which you can subsequently make a selection:

• Height: 35 mm
• Width: 204 mm
• Length: 240 mm

As a rule, sometimes analogues for the Chevrolet Orlando I J309 may be several millimeters larger or smaller than the original, there is nothing wrong with that. And if the difference is measured in centimeters, then of course it’s worth looking for another option.

Selecting an original cabin filter

The manufacturer recommends using exclusively original consumables, which, in general, is not surprising. They themselves are of good quality and are widely available in car dealerships, but their price may seem overpriced to many car owners.

Regardless of the configuration, on all first-generation Chevrolet Orlando (including the restyled version), the manufacturer recommends installing a cabin air purification filter, carbon with article number 1808246 (Opel 18 08 246) or General Motors 13503675 or GM 13271191.

It is worth noting that sometimes consumables and other spare parts may be supplied to dealerships under different part numbers. Which can sometimes confuse those who want to purchase an original product.

When choosing between a dust and carbon product, car owners are advised to use a carbon filter element. This filter is more expensive, but it cleans the air much better.

It is easy to distinguish - the paper filter accordion is impregnated with a carbon composition, and therefore has a dark gray color. The filter cleans the air flow from dust, fine dirt, germs, bacteria and enhances the protection of your lungs.

Which analogues to choose

In addition to simple cabin filters, there are also carbon filters that filter the air more effectively, but they are more expensive. The advantage of coal SF is that it does not allow foreign odors coming from the road (street) to penetrate into the car interior.

But this filter element also has a drawback - air does not pass through it well. GodWill and Corteco carbon filters are of fairly high quality and are a good replacement for the original.

However, in some retail outlets the price of the original first-generation Chevrolet Orlando cabin filter may be greatly inflated. In this case, it makes sense to purchase a non-original consumable item. In particular, cabin filters are considered quite popular:

Conventional dust cabin filters

• MANN-FILTER CU 2442 – technologically advanced consumables from a well-known manufacturer
• BIG Filter GB-9941 – popular brand, good fine cleaning
• TSN 9.7.764 is a good manufacturer with a reasonable price

Carbon cabin filters

• MANN-FILTER CUK 2442 – high-quality and thick carbon coating
• BIG Filter GB-9941/C – activated carbon
• TSN 9.7.765 – normal quality, affordable price

It makes sense to take a closer look at the products of other companies - they also specialize in the production of high-quality consumables for passenger cars:

• Amd
• Bosch
• Denso
• Filtron
• Fortech
• JS Asakashi
• Knecht Mahle
• Kortex
• Masuma
• Miles
• Raf filter
• SCT
• Sakura
• Stellox
• Valeo
• Zekkert
• Nevsky filter

It is quite possible that sellers may recommend replacing the Orlando I J309 cabin filter with non-original cheap substitutes with a much smaller thickness. They are not worth buying, since their filtering characteristics are unlikely to be at the proper level.