Wheel bolt pattern parameters for VAZ-2110

Standard disk sizes VAZ 1.6i 16V 2112x

The VAZ 2112 1.6i 16V 2112x model was produced from 2004 to 2009. Table of standard and suitable wheel sizes for VAZ 2112 1.6i 16V 2112x.

Disc drilling parameters are usually called bolt pattern:

• LZ (number of holes)
• PCD (hole center circle diameter)
• ET (disc offset)
• DIA (hole diameter)

This is interesting: What are all-season tires

General background information

Ranges of possible values ​​for tires and wheels VAZ 2112 2003.
Tires

Wheel disks

Photo

Expert advice

When choosing tires for a car, you must first follow the manufacturer's instructions. Ask yourself a few questions.

• On what roads will the car be primarily used?
• Do you need increased cross-country ability?
• How much of the route will be city roads and how much will be highways?
• Will the vehicle carry heavy loads?

The answers to these and similar questions will help determine which tire parameters you need to pay special attention to.

How to choose the right wheels for a VAZ 2112 2003?

3 types of rims:

• Stamped (economical price category) - made from a sheet of iron by stamping on a press.
• Light alloy - manufactured by casting (more reliable than stamped ones).
• Forged (the highest quality and more expensive than the previous ones) - made from light alloys by stamping at high temperatures.

The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface on which you have to drive every day must also be taken into account.

So, if it gets into a hole, a stamped disk will bend and will not cause harm to the tire, but a forged or cast one can cut it. There is a possibility that the cast disc may burst or crack.

It should also be noted that repairing “stamping” wheels is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less, because lighter and have more perfect geometry (better balanced).

The same wheels may or may not rub with tires on the same car - wheel alignment adjustment will help here.

What is the tire pressure?

It is the driver's responsibility to constantly monitor tire pressure. This will avoid standard problems associated with vehicle operation. An abnormal pressure value often causes:

• deterioration of management;
• uneven tread wear.

Often the car owner independently reduces the pressure in the wheels of his own vehicle. This reduces the load on the suspension, and the car “passes” various road irregularities an order of magnitude easier. But it is worth noting: a decrease in pressure even by 0.1 MPa leads to serious problems. The main ones include:

• increased fuel consumption;
• rapid wear of the outer tread segments;
• the car becomes less maneuverable.

An overinflated wheel causes no less problems. The central part of the cylinder begins to wear off quickly. In addition, at ambient temperatures of more than 60 degrees Celsius, the tire may simply explode. Which will lead to driving into the oncoming lane.

What is a bolt pattern?

4 bolt holes are 4

• The first number “4” indicated in the parameters indicates the number of holes located on the hub, intended for screwing wheel bolts into them.
• The second number “98” indicates the diameter in millimeters of the circle in which those same mounting bolts are located.

Thus, it is not at all difficult to calculate that the bolts are located at a distance of 69.3 mm from each other.

Wheels from Logan (bolt pattern 4*100)

Based on safety requirements, wheels with such a bolt pattern cannot be installed on a VAZ-2112. But, some drivers install such discs using spacers or eccentric bolts

Bolts with eccentric allow you to install discs with a 4*100 bolt pattern on a 4*98 hub

This is on their conscience, as other drivers may suffer.

conclusions

It’s not at all difficult to understand such parameters, the main thing is to remember them and choosing suitable wheels ceases to be a difficulty.

Dull VAZ stamped wheels are often hidden behind elaborate plastic caps. And for good reason. Every owner of a VAZ-2110 wants his car to stand out from the mass of gray and black dozens.

One of the ways to improve the appearance of a car is deservedly considered to be replacing the wheels. Not many people think that when selecting a replacement disk, you need to take into account not only the number of mounting holes. Today we will look into the bolt pattern of VAZ-2110 wheels and select several options for a simple and bloodless replacement.

Manufacturers

The domestic industry produces several types of rubber suitable for LADA 112. Tires that are in good demand today are:

• Kama - in Russian and European versions.
• Cordiant.

Many VAZ 2112 owners prefer to put foreign-made tires on their car. The most popular are:

• Yokohama,
• Bridgestone
• Goodyear
• Nokian Hakka Green,
• Michelin.

When choosing tires, it is very important to consider the quietness of the rubber. If it makes a loud sound, the ride comfort will be lost. It must be said that when choosing tires, it is also necessary to take into account what roads the VAZ will drive on, driving style and travel distance.

Preparing for adjustment

Most often, the VAZ 2110 camber and alignment are installed at a service station, but you can do it yourself. First of all, check whether there is play in the bearings and whether the steering is loose. At the same time, check the diameter and absence of deformation of the disks, air pressure in the tires, and tread wear.

VAZ 2110 front suspension assembly diagram

Naturally, if a wheel is loose, action will need to be taken, and one with improper tread wear may need to be replaced. Wheels standing on the ground need to be pulled relative to the vertical. If you find any play, have a helper apply the brake and check the play again.

If it disappears, the bearing needs to be replaced. If after this the size of the play not only does not disappear, but only decreases slightly, the suspension needs to be checked, repaired, and sometimes replaced.

Front wheel hub diagram

After this, hang the wheel and check the play again. It is possible that the play has disappeared, but the wheel turns jerkily or is simply difficult, then you need to slightly expand the diameter of the bearing installation site.

If you hear a grinding noise, the bearing needs to be replaced.

Types of rims

Today Russian disks have become very popular:

• KiK,
• Scud.

Car enthusiasts give a very high rating to the products of the Verkhnaya Salda metallurgical plant, which produces forged models called LS FlowForming.

Light alloy cast products made in Germany are also in great demand:

• A.E.Z.
• Dezent,
• Dotz.

The samples listed above have long been considered classics among car rims.

The Italians delight with their beautiful appearance and attractive design. The most striking of their products are:

• OZ Racing,
• Alessio.

In recent years, Korean products, manufactured in Taiwan, Indonesia, and South Korea, have begun to appear on the domestic market.

It must be said that all these rims differ from their analogues in very high quality. The fact is that for production at factories the latest technology developed by the world's leading manufacturers is used.

Engineers from Japan, Italy and Germany have been developing such a technological process for many years. Therefore, all the nuances and subtleties of production were taken into account. The innovative technology they created enabled Korean specialists to produce only the highest quality products.

When choosing, there are two more points to consider:

• Front-wheel drive VAZ 2112 cars can be equipped with 5.5x14.6x14 wheels.
• If a low-profile tire is installed, you can use 6x15, 6.5x15.

However, I would like to warn you that the manufacturer does not allow the installation of r15. Complications may arise during the technical inspection. Tires of this size do not fit all wheels.

This is interesting: How to correctly change summer tires to winter ones

Features of sidewalk parking

Since a catastrophic situation has arisen in cities due to a lack of parking spaces, municipal authorities allow cars to be parked on the sidewalks in certain situations. So-called sidewalk parking lots are formed, and two main conditions must apply here.

Firstly, these are specially designated places.

Secondly, such places must be marked with permitting signs. A “Parking” road sign is installed, as well as explanatory signs indicating how to install the machine.

Information on signs

Special signs may indicate the option of identifying a vehicle for parking.

1. On the road near the curb. The sidewalk runs parallel.
2. Full access to the sidewalk. The street is parallel.
3. Driving onto the sidewalk with the rear wheels or the front wheels.
4. Parallel to the roadway. You can drive onto the sidewalk with side wheels (any pair).
5. On the road surface. The front part is directed towards the road, the car is located perpendicular to the street.
6. Full access to the sidewalk. The car is positioned perpendicular to the movement, the front side is directed either towards the houses or towards the road.

Disc bolt pattern and factory tire sizes on the VAZ-2112

On all models of the VAZ-2112 car from the factory, the bolt pattern had a size of 4x98 . And straight from the assembly line it was supposed to install wheels with a 13th and 14th radius and tires of size 175/70 R13 or 175/65 R14 .

Such “stamps” are suitable for VAZ-2112 (Kremenchug)

• About the expert:

All my life I have been surrounded by cars! First, in the village, already in the first grade, I was rushing around on a tractor through the fields, then there was JAVA, then a penny. Now I am a third-year student at the Polytechnic Faculty of Automotive Engineering. I work part-time as a car mechanic and help repair cars for all my friends.

However, if in the case of size, then everything is more or less clear, then what a bolt pattern is is a big mystery to many. We will tell you more about this below.

Tire pressure VAZ 2107

The nominal tire pressure depends on the type of tire and the load on the vehicle. If the wheels are overinflated or low, the contact patch between the tire and the road changes. This causes deterioration in controllability and an increase in braking distance. In addition, uneven accelerated wear of the tread begins. Over-inflated tires increase wear on the center of the tire, while under-inflated tires increase wear on the edges.

It is recommended to check tire pressure after 500 km, but in practice it is better to do this more often. Small tire punctures, disc and spool defects cause air to escape from individual tires. In this case, the car may drift off course, especially when braking.

The nominal pressure in VAZ 2107 tires depends on the tire size:

• 165/80R13 - 1.6 for front, 1.9 for rear wheels;
• 175/70R13 - 1.7 for front, 2.0 for rear wheels.

In hot weather and when driving, tire pressure increases. With an aggressive driving style, taking sharp turns at high speed, the pressure can increase to 3-4 atmospheres. The tire material is designed for this and can withstand such changes. But if there is a hernia or cut on the tire, it may explode. A front tire explosion is especially dangerous, after which it is very difficult to keep the car on the road.

As pressure decreases, rolling resistance increases, which leads to increased fuel consumption. The tire also bends and the car becomes less responsive when maneuvering.

If the tire pressure is too low, the tires may even fall apart when cornering sharply.

Wheels for cars

A model such as the VAZ 2112 has long been firmly entrenched in the country’s market as legendary. During production, a huge number of vehicles were produced. The popularity is due to the low price and ease of maintenance of the machine. It was produced in sedan, station wagon, hatchback and coupe bodies.

VAZ 2112 car black, on white rims

Regardless of the body type, the same wheels were installed on 2112 from AvtoVAZ. The cars had absolutely identical parameters and characteristics. High popularity and widespread distribution have created a huge number of offers for the sale of spare parts, wheels and tires.

Important!

The VAZ 2112 comes off the assembly line only on rims with radii R13 and R14.

Many car enthusiasts prefer to install wheels that exceed the factory dimensions; in this case, it is necessary to take into account the dimensions of the wheel arches. It is necessary that the wheel does not touch the arch structure while driving.

In the factory configuration, in addition to stamped options, there are also some versions with cast products. However, every car owner comes to a time when it is necessary to change wheels. This happens due to excessive wear and tear, multiple damages, changing seasons and many other reasons.

When such a need arises, there is plenty to choose from on the country’s market. Both original stamped or light alloy wheels and products from various other brands are presented.

Forged wheels for VAZ 2112

Over all the years that the car was produced, there were no changes in the parameters and characteristics of the wheel mounts. This means that you can easily install them from earlier or other models to the latest ones and vice versa. Some Russian wheel manufacturers produce a special line of products for the VAZ 2112. This guarantees a perfect match of all sizes.

You may be interested in this About Sakura Wheels for cars

The most popular is the installation of 15 rims on 2112. This is the most convenient solution, since this size meets all the manufacturer’s requirements and does not affect the smoothness and comfort of the ride.

Note!

Almost all cars in the line have identical drilling parameters.

Its standard parameter is 4x98. This means that to install the wheels, four bolts are required, which are fastened at an axial distance of 98 millimeters. It is a very popular mounting method among machines of any manufacturer. In this regard, car owners usually do not have difficulties with the selection of wheel rims.

If there is a need to replace wheel rims, then many different parameters and characteristics should be taken into account. The main dimensions include the width and height of the rim, offset and drilling. Taking them into account, you can buy products regardless of the method of their production.

To make the right selection, it is important to know the following factors:

• In winter, it is better to use wheels with a minimum diameter and rim width. This is due to the need to obtain maximum stability in bad weather on any road surface;
• During the period from spring to early autumn, when driving conditions are normal, there is no need to comply with any requirements. You can install products of the maximum permissible sizes, which will give greater controllability and stability on the road;
• The height of the rubber profile affects the level of wear and comfort. When increasing the rim diameter in summer, you should lower the tire profile height.

Among tuning enthusiasts, it is popular to modify the design of a car to install very large wheels.

Tires for VAZ 2107

Tire and wheel sizes for Daewoo Nexia 2005

The safety of the car driver and his passengers depends even more on the characteristics and condition of the car’s tires. Their choice must be approached very carefully, and in no case should you skimp.

Types of tires by seasonal use

According to seasonal use, tires are divided into:

The first ones are made of soft rubber and have a special tread. At the same time, each manufacturer tries to increase the tread area, because the larger it is, the better the tire will perform on winter roads.

Summer tires are rougher, and their tread pattern is designed more for better grip on wet surfaces and drainage of water from the plane of contact between the tire and the road.

All-season tires are a generalized version of the first two types. If the “all-season” tire is really of high quality, then in winter it copes with its duties normally, but in the summer it is significantly inferior to summer tires in terms of the quality of grip on wet surfaces.

VAZ 2107 tire parameters

Like wheels, car tires have their own parameters. These include:

• profile width (the width of the tire itself, measured in millimeters);
• height (expressed as a percentage of the profile height to the width, measured as a percentage);
• landing diameter (determines the inner diameter of the tire, measured in inches);
• load capacity (indicates the maximum load per tire, measured in kgf);
• permissible speed value (indicates the estimated maximum permissible speed, measured in km/h).

VAZ 2107 leaves the assembly line of the plant shod with thirteen-inch radial tires with a profile width of 175 or 165 mm and a height of 70%. Standard tires are designed for 190 km/h and a load on one wheel not exceeding 470 kgf.

It is impossible not to mention the tire pressure, because the vehicle’s cross-country ability, its driving performance, and fuel consumption depend on it. The manufacturer of the VAZ 2107 recommends observing the following pressure indicators.

Table: recommended tire pressure for VAZ 2107

The choice between beauty and functionality of wheels should be based on how you use the car. If it is intended for city car rides, or participates in exhibitions of tuned cars, festive motorcades, then alloy wheels and low-profile tires are an ideal option. If the car is used daily in our off-road conditions for work, then it is better to install “stamping” on it with standard tires.

What is the bolt pattern on 7 4 by 98?

NEVER put hundred square meters in the wrong place. Better 98 zbs

0 0 Answer rating: 0

0 0 Answer rating: 0

Why is it important to choose the right size?

The most popular wheel sizes for installation are R14 and R15. This is due to the fact that they can be easily selected in a store and installed on a car. The main thing is to comply with the required dimensions and bolt pattern parameters specified by the manufacturer. If products with dimensions different from the factory ones are selected, then special adapter rings should be used. They often come with the product.

You might be interested in this About the bolt pattern characteristics of Mazda wheels

Adapter rings for wheels for VAZ 2112

Note!

The main problem that prevents the installation of large products is the size of the wheel arches.

If you exceed the dimensions and do not modify the wheel arches, then the rubber will touch the body structure itself during maneuvers, which leads to increased wear of all suspension components and parts and a decrease in safety.

To avoid these difficulties, it is necessary to install products only with guaranteed suitable parameters and dimensions. For the VAZ 2112, these are the diameters R14 and R15, which have factory parameters and meet all safety requirements and other characteristics.

Wheels of this size will give the car the best level of driving comfort.

As for increasing the size of the rim, their operation has its positive and negative sides, which every car enthusiast needs to know. However, the decision to purchase and replace disks should be made only by the owner of the machine.

Pros:

• Good car behavior in the lane;
• Improving the exterior of the car;
• The best road qualities, including dynamics and handling;
• Maximum absorption of potholes and road defects;
• When using rubber with a high profile, the wear resistance of chassis parts increases;
• Reducing the braking distance.

Minuses:

• Reduced level of comfort in motion. This is due to the high sensitivity of the chassis to road defects;
• Difficulty in parking and driving on poorly paved roads;
• Increased requirements for pressure control in low-profile tires;
• Increased gasoline consumption, which is associated with the increased difficulty of driving the wheels;
• High price.

Corrosion protection

For reliable operation of the chassis, everything is important: the bolt pattern, the dimensions of all components, the alignment/camber settings, and even the protection of the arches from corrosion. It is the arches that are more susceptible to adverse factors than other parts of the body - from ordinary moisture during rain to reagents on winter roads

To ensure reliable protection of the arches, it is best to install lockers (fender liners) on the VAZ 2110. Such protection will cost much less than subsequent repairs of rusted arches

It is important to choose the correct size of the lockers and ensure their tight fit in the area of ​​the arches

https://youtube.com/watch?v=o2FUAvK29RU

We hope that by completing all the repair work yourself, you will provide your VAZ 2110 with many years of trouble-free service on the road.