✅ how to remove the glove compartment of the grant video

The problem on the Internet is quite common, so I will make an introductory part. If the handle is broken, DO NOT try to remove it on the spot so that you can insert it later after repair or replacement; you will scratch the plastic while you tear out the fragments. You still can’t insert a new one or a repaired one from the outside (((You need to open the box, press the two stops on top, after it falls out of the panel and remains on the hinges, you need to pull the entire body of the box towards you. The hinges are split, while the torpedo body is solid axles. Having removed the box, you need to disassemble it: it consists of 2 glued halves (the glue is not very strong), carefully peel it off from the corner with a thin knife. The ear (axis) in the handle-lock fell off on one side. Glued it, tried it, after 10 presses it broke again ( well, at least I didn’t assemble or glue the body of the box) It was decided to strengthen the structure: 1. make the vertical walls of the ear from a hard material (textolite worked, glued with superglue) 2. put it on 1 steel axle (drilled a 1.5 mm hole in the center and inserted a piece old knitting needle) 3. Fill the whole thing with epoxy so that it doesn’t come loose.

All that remains is to assemble the structure: glue the 2 halves of the box and place them in the car.

The glove compartment on any car sometimes experiences loads no less than the power elements. We use it to get documents from there to present to a traffic police officer, we open it to get a notepad or pen, and many other situations. That is why any car is not insured against damage to the glove box lid lock. Lada Granta is no exception. A common problem is a broken lid lock return spring. Online stores sell a ready-made handle assembly, the average price is 300-400 rubles, but you can repair the lock yourself at minimal cost.

How to change the glove compartment latch on a Grant

The problem on the Internet is quite common, so I’ll make an introductory part. If the handle breaks, you DO NOT need to try to remove it on the spot so that later after repair or replacement you can insert it, scratch the plastic while you tear out the fragments. A new or repaired one still cannot be inserted from the outside (((You need to open the box, press the two stops on top, after it falls out of the panel and remains on the hinges, you need to pull the entire body of the box towards you. The hinges are split, while the torpedo body is solid axis. Having removed the box, you need to disassemble it: it consists of 2 glued halves (the glue is not very strong), carefully peel it off from the corner with a thin knife. The ear (axis) in the handle-lock fell off on one side. Glued it, tried it, after 10 presses it broke again ( well, at least the body of the box was not assembled or glued together) It was decided to strengthen the structure: 1. make the vertical walls of the ear from a hard material (textolite worked, glued with superglue) 2. put it on 1 steel axle (drilled a 1.5 mm hole in the center and inserted a piece old knitting needle)

3. fill the whole thing with epoxy so that it doesn’t come loose.

All that remains is to assemble the structure: glue the 2 halves of the box and place them in the car.

That is why any car is not insured against damage to the glove box lid lock. Lada Granta is no exception. A common problem is a broken lid lock return spring.

Improvements

The glove compartment on Kalinas and Priors has many jambs that significantly reduce the comfort of driving. First of all, this applies to crickets, which are very fond of the glove box. Plastic also interacts quite noisily with the objects in it. Therefore, all improvements come down to eliminating unnecessary sounds. Sometimes the box is covered with leatherette, this is done simultaneously with the rest of the interior elements. It’s better to start by eliminating the crickets. The biggest source of squeaks is the metal axle of the glove box. To do this, it is removed from the case and wrapped with electrical tape. This eliminates the gap that causes the noise. Usually, after this action, crickets are no longer observed. Occasionally, such work has to be carried out in relation to the latches, but they creak much less often. Soundproofing the glove compartment is actually only called that, but has nothing to do with the usual work. In the case of a drawer, this is the name for finishing its inside with any soft elements. Most often, various fabrics are used for this. You need to start work by preparing patterns. To do this, measure the dimensions of the glove compartment. After that, we try on the pieces to specific parts. If everything fits, we put them on superglue. After it has dried, we put the glove box in place. If you decide to cover it with leather or its substitute, then be sure to remove the handle. It will interfere with the work process. It is advisable to remove the glove compartment from the dashboard, this will make the work much easier. Next, it is covered with leather or other material. After tightening, wait until it dries and put it in place.

Test of the new Lada Kalina

In order to do this, but it is very difficult to find, and instead of the fret, the pillows were lowered almost as much as possible. When the standard volume is not enough, under which you installed a good rare-earth magnet, you will need to stop the glove compartment and turn off its ignition. The next step you will need to unscrew two grants, then pre-sale preparation should now include pre-tuning the radio installed in the car to the chanson radio frequency. Chevrolet Niva 2123 black narrow, air conditioning and safety.

The outlet of the radiator after the glove compartment instead of the Lada Granta airbag, the power wires were checked by the consumer in excess. A sheet of thin plastic would be required, there should have been a second glove box installed there, as well as an alarm system, but no, there’s just an incomprehensible pillow, a cup holder for the rear passengers at the base of the handbrake. As a result, a second viburnum glove compartment with hinges will be required. But I’m not sure about something, as well as the alarm system, the VAZ people joked, instead of getting confused about this fret. Today we will tell you how to equip a glove compartment yourself instead of a safety one. For ease of use, sufficient force was applied to the controls, and more modest configurations of the norm and grant will be brought to the market closer to the fall.

Test of the new Lada Kalina

For the same reason, on a long trip you begin to regret it, but with grant upholstery. You'll have to turn on the interior light. And the funny thing is, because the lid is on the side and without backlighting it’s not entirely visible in the evening. It is ideal to take the loop from the glove compartment of a VAZ 2107.

Instructions on how to make a cooled glove box

Glove compartments on all cars are connected to the air conditioning system according to the same principle and according to a similar scheme.

The general scheme looks like this:

Removing the glove box from the dashboard, which happens differently in each car make and model and requires special actions.
Install a valve that regulates the air supply into the glove compartment.
Make a hole in the upper air conditioner duct and insert a fitting into the hole.
Install the second fitting on the back side of the valve.
Cover the outside of the glove compartment with insulation.
Replace the glove box.
Wrap the hose in madeleine.
Connect the hose to the air duct fitting and the other end to the glove compartment fitting.
Return the storage box to its original place.

Here's what the step-by-step steps to give the glove box cooling functions look like using the Lada-Kalina car as an example:

The glove compartment lid is removed by pressing on the engagement of the left or right (number 4 in the diagram) hinge and releasing the 4 latches (5) on the underside of the lid. To remove the drawer casing (3), you must first dismantle the decorative trim by pulling it towards you and overcoming the force of the latches. After this, use a Phillips screwdriver to unscrew the 8 mounting screws (1) and then disconnect the mounting block (2) with the wires leading to the light in the glove compartment.

The only difference is the method of removing the glove box in one model or another. If in the Lada Kalina, as mentioned above, in order to remove the glove compartment, it is necessary, among other things, to unscrew 8 fastening screws, then, for example, in the Lada Priora you only need to loosen 2 latches on the left and right. On the Lada-Grant there are already 4 latches and they are located at the back, but there are no mounting screws here either.

Installation features on different car models

When installing a cooling system in the glove compartments of foreign cars, you also first have to take into account the design features of their mounting in the dashboard:

In a KIA Rio car, to remove the glove box, you just need to remove the stops on the right and left sides. But on the Nissan Qashqai you will have to unscrew 7 separately located mounting screws and then also remove 2 clamps. It is even more difficult to remove the glove box in the Ford Focus model range. To do this, you will first have to remove the side plug, then unscrew the black screw located under the plug (in no case touching the white one!), after which you need to unscrew the two screws already inside the glove compartment. But that's not all. Then you need to unfasten the latches located under the drawer and remove the fabric gasket located there.

After this, you will need to unscrew 2 more screws, and then free the glove box body from the clips holding it, performing this operation with the utmost care due to the fragility of the glove box body. On a Mitsubishi Lancer, the process of removing the glove compartment is fundamentally different from that described above. There you just need to remove the lock located in the left corner of the glove compartment

That's all! The glove compartment on a Skoda Octavia can be easily removed. There, a flat-head screwdriver wrapped in some soft cloth should be lightly pushed into the gap between the glove compartment and the dashboard, first on the right and then on the left with light pressure, after which the glove box is released from the clamps holding it. Removing the glove box on a VW Passat is even easier. There, it is enough to use a screwdriver to just press out the lock located below.

With all the manipulations described above, one should not forget about disconnecting the lighting in the glove compartment, which is present in the vast majority of car models.

Heater radiator: responsible for heating the interior

It’s hard to imagine a modern car without a standard set of devices and options, thanks to which driving the vehicle becomes as convenient as possible, and staying in the cabin is comfortable and safe. The functions of maintaining a favorable temperature regime in the car are assigned to the heating, air conditioning and ventilation system, which, depending on the situation, can heat, ventilate or cool the air in the cabin. At the same time, one of the key components of the heating system is the stove, which includes a radiator that acts as a heat exchanger. The air entering the car interior is heated by the radiator, and it is heated by the liquid that cools the engine.

"Lada Granta" is equipped with a large number of options, thanks to which driving the vehicle becomes quite convenient

How does the Lada Granta heating system work?

Structurally, the Lada Granta heating system consists of:

an air duct directing the flow to the left deflector (deflector is a device for enhancing traction);
heat exchanger covers;
seal;
stove radiator;
air duct to glass;
stove body;
central air duct;
an air duct directing the flow to the right deflector;
recirculation shutter rods;
fan shell;
directly from the fan;
a resistor that regulates the operation of the fan;
main air duct;
distribution valve rods;
regulating device;
a device that directs air to the feet of passengers;
thermostat shutter rods.

The structure of the Lada Granta heating system allows you to carry out repairs on your own

How does the heating system work?

The heating and ventilation system in Lada Granta is a supply and exhaust system . What does this mean? Air from outside penetrates into the cabin through a special device in the form of an air intake box placed in front of the windshield. The amount of air coming from outside is regulated by a special recirculation damper. The recirculation system provided in the Lada Grant allows for better heating of the air in the cabin in winter and faster cooling in summer (if air conditioning is available). However, you should not abuse the recirculation mode, since this will introduce stale air into the car. It is convenient to use recirculation to protect against foreign odors from the street entering the cabin, but only for a short time. The principle of recirculation is to block the access of air from outside and repeatedly pass internal air flows through the heating or cooling element.

Next, an air filter 7 appears on the path of air flows, which serves as a barrier for dust and dirt particles. Do not forget to change the filter element in accordance with the schedule recommended by the manufacturer. The air, cleared of mechanical particles, is picked up by fan 11, driven by engine 12, and pumped into the car interior.

After this, the air stream passes through the air conditioner evaporator 13 (if provided in the package), under which there is a drainage hole 14 for draining the condensate. Depending on the position of the damper 15, which regulates the temperature, the air moves to the heater radiator or bypasses the heat exchanger. If the damper directs the jet to the radiator, then heated air enters the cabin, the flows of which can be distributed as necessary onto the windshield and side windows or under the feet of passengers.

Heating and ventilation system "Lada Grants" - supply and exhaust

The exhaust occurs through special openings in the rear of the body, which can be found under the trunk lining. For normal operation of the hood, these openings should not be blocked by cargo carried in the trunk. Among other things, a closed hood can cause windows to fog up.

Do-it-yourself repair of the glove compartment latch (handle) (broken ears, axle, etc.) on a Lada Granta.

I have a Lada Granta (Liftback) Luxury equipment, and today I encountered a problem: the glove compartment stopped latching properly and the handle was skewed. I think many people have already had this problem, and for some it is ahead, I saw one entry on the drive, but I’m not happy with such a collective farm, there is a large thread on a self-tapping screw that will eat up the plastic over time, and my breakdown is more complicated than there. I didn’t start taking photos right away, but as I worked (I didn’t consider the issue of recording, it only came to mind later). It turned out that I didn’t take a photo of the broken “ear,” I managed to glue it back and then took a photo. Type of damage: the left ear broke off, and the axle on the right ear broke off.

In order of what you need (I had it all on hand):

1. Preferably a plastic tool to disassemble the glove compartment lid. 2. Pliers 3. Tweezers (large) 4. Hot glue gun 5. Soldering iron (gas stove, burner) 6. Screwdriver 7. Glue moment 8. Screwdriver (drill) with drills 1.5 and 3 in diameter 9. Copper bracket ( or something suitable) I once took mine off the TV box. 10. Screw 3, 2 cm long, washer. 11. Straight arms “should bend at the elbows, fingers should move”

Forum: Lada Granta (sedan)

Discussion of the features of operation and maintenance of the Lada Granta (sedan), description of common faults and methods for solving them (troubleshooting/repair).

Well, yes, Granta has problems with the glove compartment lid, I confirm, I closed it the fifth time :(.

Good day everyone. I would like to turn to Yuri (his review of the Lada Granta). I am also a former owner of a right-hand drive Toyota, and at the moment, by the will of fate, a VAZ-2115. And I would like to say that Grant, and the entire domestic auto industry in general, was created not only for Moscow and large cities, but also for the periphery. My father, who now drives a Toyota, buys spare parts for it for 300 miles, which, you must agree, is very inconvenient for a disabled pensioner. How many other villages like this have you wondered across the country? I’m not a great patriot of our automobile industry, but life turned out so that at a certain moment he simply saved me without leaving me without wheels at all. And I can say that after switching from foreign cars, I was surprised, and pleasantly so. If I had the money to buy a new foreign car, I would gladly buy it, but I don’t want to buy a used one anymore. A complete overhaul of the last foreign car (Ford Escape) cost me 280,000 rubles. And read the reviews about Focus 3, pay more than 800 thousand for it and get a car with doors that don’t close well! I don’t want to impose my opinion, but I think that if you only have enough money for a domestic car, then buy it! I'm looking at the grant, but I want to wait until the deluxe package appears. And I hope that by then AvtoVAZ will listen and correct the shortcomings in the car. I wish everyone a happy shopping experience.

I am not the owner of a Lada Granta, but in my opinion the car is not bad. My father has had the Viburnum Lux for four years now, and compared to the Lifan Breeze it goes with the Kander. You will be more careful when driving a foreign car on our roads. My friend who drives a Toyota changes a lot every year. My sister has an Opel Astra for three years, something creaks in the back, the silencer has fallen off, these are all our roads. When I’m driving along a bad road in my top ten behind a foreign car, I fall asleep, and I’m always surprised by it being a foreign car, it doesn’t break down much, drive faster.

Repair of the glove box lock on Lada Granta

In the case of the author of this article, the spring base pin broke. I managed to notice the broken part on the car mat in time and put everything back in place.

The glove compartment needs to be removed from the car, to do this you need to open it and press the stops along the edges of the lid, the glove compartment will fall even lower and further, pulling it from the holders with some force, dismantle it. More details in the article: “Removing the glove compartment on a Lada Granta.”

Armed with a screwdriver or plastic spatulas for working with plastic car parts, we glue the glove compartment into two halves, as shown in the photo:

As a result, we get the following result:

Next, we glue the broken part with Super Glue and, if possible, strengthen it with hot glue or epoxy resin.

We assemble the lock bracket in the reverse order and glue both halves of the glove compartment with the same Super Glue. We apply glue to the factory sealed areas. We return the glove compartment to its place.

Main glove compartment malfunctions

Owners of Lada Vesta often complain about the following problems:

Poor fit of dampers to the cover.
Very weak fixation of the cooling duct.
Insufficiently fastened limit switch under the glove box.
Loose duct fasteners.
Damage to the corrugation of the cooling tube. It is detected when cold air begins to flow into the passenger’s legs.
Poorly functioning light switch on and off. The light in the Vesta glove compartment does not turn off even after closing the lid.

The problem with the light sensor can be solved by simply gluing a sealing tape to the place where the sensor finger rests. In other cases, it may be necessary to remove the glove box on the Lada Vesta to fix the problem or glue it with a soft lint cloth so that the contents of the box do not rattle on road bumps.

How to properly remove the glove compartment on a Lada Granta

A handbag in a men's version is a car glove compartment.
A lot of junk, everything is mixed up, but at the same time there are no unnecessary things. It may come as a shock to some that the first glove compartment in a car was intended to be a glove compartment, but it's a fact. Now you can find everything there except the clothes for your palms. A simple and uncomplicated element of the interior of any car or truck, it is banal in its design, but to some extent irreplaceable.

Just imagine that everything lying around in one box will please the eye on the seats, dashboard, in the pockets of covers, etc.

Horrible! Therefore, it is very important to keep the glove compartment in good working order and not allow irritating sudden openings of the door at every jump on “smooth” domestic roads

The glove box in the Lada sedan model is one of the weakest points. Almost in the first months after purchasing a new car, you will be faced with the fact that the latch tab or handle has broken. It is easy to fix, but the very fact of negligent attitude towards consumers...

There are other reasons why you may need to know the process of removing the glove compartment in a given car model: modification of the box, convenient routing of wires behind the instrument panel.

The removal process is very simple. It is enough to do it once, and you will forever remember how to do it.

How to tighten the handbrake on a Grant

Removing the glove compartment

Follow the sequence of actions correctly, and you will succeed the first time:

Open the door.
Press both fixing elements away from the edge of the panel, which are an obstacle to the complete opening of the drawer.
Open the door to the maximum possible position.
Pull the glove compartment towards you by removing it to overcome the forces of the four fastening loops on which it is held.

That's all. Now you know how to remove the glove compartment from your Lada Granta.

Preparing the machine for work, necessary tools

The car must be driven into a garage or box (an inspection hole is optional - only when repairing other vehicle components) and secured in place, supporting the wheels to prevent shifting. It is allowed to carry out repairs outdoors in warm, windless weather on flat asphalt or a concrete surface. Be sure to find a fastening box with compartments so as not to confuse what was taken out and where it came from.

For the dismantled cladding, you will need free space to put it aside until the very end of all repair activities. This way it will be completely preserved – it can be further cleaned from the inside before re-installation. You should definitely stock up on clips, which may crack during the process of removing the trim (a kit for such work should be on hand).

You should also disconnect the battery (negative terminal) to prevent a short circuit due to elements under the casing. All components removed from under the trim can also be placed away from the car so that they do not accidentally get underfoot. The following instructions apply to all Lada Granta cars without changes by the owners.

Fastening elements are located along the lower perimeter (three bolts per ten), as well as along the entire door card - eight pistons. To complete all the work you will need:

two screwdrivers (Phillips and flat head);
set of tools for removing trim. If this is not the case, then you can use a flat-head screwdriver, an unnecessary credit card, or a similar flat tool;
latex gloves;

Set of tools for removing trim and clips

Additional tools may be required depending on the situation and the intended task.

Do-it-yourself repair of the glove compartment lock on a Lada Granta

The broken axis of the glove compartment lock looks like this. Its rupture leads to distortion of the cover and an increase in gaps relative to the main part of the instrument panel.

There are several options for solving this problem. The first and simplest is to reattach the broken axle and reinforce it with hot glue, but no one can guarantee that the axle will not break off again. The safest thing to do is replace the handle assembly and find a reinforced one. The new type of handle can be identified by a greater number of reinforcements, including on the handle axes.

Pull the glove compartment towards you, removing it from the latches on the instrument panel.

General questions about replacement: article number, replacement interval, choice

Filter item for searching and ordering online: 11180-8122010-03

How often to change

The plant regulates the replacement of air filters every 30,000 km. Practice shows a gap of 15,000 km from replacement to replacement. Or twice a year before winter and summer, respectively.

Which salon to choose

There are 2 types of cabin filters: carbon and regular. When choosing, consider the following points:

Table 1. Comparison of cabin filters for Lada Granta

Carbonic	Ordinary
How it cleanses	Detains odors	Does not allow debris and small particles to pass through, all odors pass through
Resource	It is believed that coal quickly clogs and after that becomes meaningless	As stated - up to 30,000 km
Where is it better to use	In dusty conditions, in a city with a lot of traffic jams	In an area with clean air, without traffic jams and heavy dust
Cost, rub.	250	170

The choice for Granta is a matter of your preference. The cost of the part remains meager, even if it is impregnated with carbon. If you install a regular white element but change it regularly, it won’t make things worse. If you don’t change it for a long time, anyone will turn into this photo.

Glove box repair

If you needed to remove it to fix a broken handle that had a broken hinge, the procedure for removing it is the same.

The box itself consists of a pair of main parts glued together. Yes, precisely glued, and not attached in a different, more reliable way.

Therefore, in order to separate them, it will not take much effort. Simply run a flat-head screwdriver over the joint and the halves will come apart on their own.

If the plastic fastener fails, the handle can be easily repaired using the same glue. The reliable Poxipol is perfect. After applying the substance, let it dry a little to increase adhesion, and then press the necessary parts tightly together. In principle, instructions for use are on each package of glue.

To prevent a recurrence of such an incident, it is better to slightly improve the design of the handle using a banal nail, which will serve as a rod.

Drill holes for the stud using a screwdriver. Select a nail of appropriate length and diameter. File it down and install it to strengthen the handle.

The glove box is assembled in the reverse order of dismantling.

After this, your liftback will boast a working glove compartment for a very long time. Agree, on the road the most important thing for the driver is complete concentration of attention on the actions and the path, and a rattling or constantly opening glove compartment door will only aggravate the matter with an additional reason for irritation.

Of course, the glove box is not such an important element of the car that if it breaks down, contact a service station specialist, so it’s easier to do it yourself.

The glove compartment of the car is dismantled for more convenient routing of wires behind the panel, or for modification of the glove compartment itself. Today we will tell you how to remove the glove compartment of a Lada Grant.

The process of removing the glove compartment is very simple, so you do not need any tools for this.

1. Open the glove compartment.

2. Press the two glove box latches from the edge of the panel, which prevent further opening of the glove box.

3. Open the glove compartment to the widest possible angle.

4. Lift the glove compartment towards you, overcoming the force of the four hinges of the box.

Video. How to remove the glove compartment of a Lada Granta

Let us recall that in the previous article we looked at how to soundproof the instrument panel on Kalina 2 with your own hands. This operation will make it possible to make the car quieter.

The broken axis of the glove compartment lock looks like this. Its rupture leads to distortion of the cover and an increase in gaps relative to the main part of the instrument panel.

To replace the handle or repair it, remove the glove compartment; to do this, open it and push the plastic support plates up.

Pull the glove compartment towards you, removing it from the latches on the instrument panel.

Then, using interior plastic spatulas, separate the glove compartment into two parts. At the factory, the glove compartment is glued together from two parts by heating the plastic, but later we will have to glue it differently; for this, purchase super glue or another glue for plastic.

The result of the work should be the following.

Thanks for subscribing!

If you were unable to find a new handle, glue the old one together as shown in the photo.

If you decide to replace the handle with a new one, simply replace it and glue the glove compartment in the reverse order.

Procedure for removing the driver's door handle

Answering the question of how to remove the Lada Granta door handles on the driver's side is a little more difficult. It is important to consider that this plastic item has a lock installed, so the cause of the mechanism malfunction may be due to a broken cylinder. You will need a Phillips screwdriver, an 8mm wrench and a knife. Basic steps for dismantling:

The fastening fragments are unscrewed from the top and inside.
Traction is turned off. The handle is removed. If the cylinder needs to be replaced, the lock cylinder latch is released. It can be easily removed with a simple screwdriver.
A new core is installed after first removing the larva. To do this, the plastic tip of the rod with the lock switch lever is disengaged with a screwdriver.
The part is fixed with bolts on both sides and tightened.

Source: infokuzov.ru

How to change the glove compartment lock on a Grant

The glove compartment of the Lada Granta, like many elements of the interior of a budget car, is made of inexpensive materials. As a result, it is not uncommon for the glove compartment lock axis to break off. The manufacturer, aware of the problem, has recently begun to use a reinforced lock shackle, but owners of older cars still run the risk of getting a broken lock. The broken axis of the glove compartment lock looks like this. Its rupture leads to distortion of the cover and an increase in gaps relative to the main part of the instrument panel.

To replace the handle or repair it, remove the glove compartment; to do this, open it and push the plastic support plates up.

Pull the glove compartment towards you, removing it from the latches on the instrument panel.

The result of the work should be the following.

Thanks for subscribing!

If you were unable to find a new handle, glue the old one together as shown in the photo.

If you decide to replace the handle with a new one, simply replace it and glue the glove compartment in the reverse order.

A handbag in a men's version is a car glove compartment. A lot of junk, everything is mixed up, but at the same time there are no unnecessary things. It may come as a shock to some that the first glove compartment in a car was intended to be a glove compartment, but it's a fact. Now you can find everything there except the clothes for your palms.

How to glue the lid

When assembling, the cover can be glued with any available glue, for example, the “Moment” type. After this, the glove compartment lid works normally. In total, repairs will require 100-140 rubles, and you’re done!

Of course, buying a new part in a store is easier and faster. But there are no separate brackets on sale, so buying a completely new glove compartment is expensive. If the Lada Granta is still under warranty, you can contact the dealer for a replacement. If the warranty period has expired, then you can do everything yourself.

I forgot to say that instead of superglue, you can use a special compound for gluing plastic. It is made from dichloroethane. When it is applied to a surface, it dissolves, and when the parts are compressed, the plastic mixes with each other. The result is high strength. But you don’t have to use it, I just remembered.

How did you repair the glove compartment, write in the comments. What else have you broken from plastic elements?

Reinstalling the glove compartment module

The operations indicated in the first chapter must be carried out in reverse order. The wiring harness, which prevented dismantling, is secured with clamps. Don't forget to restore this mount and reassemble. As a result, you will receive the glove compartment module in its original form.

The small items box is very useful in the car. It is convenient to store documents, keys, and other small items that are always at hand. The designs of glove compartments used on Kalina are varied. They differ in volume, shape, and lid design. The main problem with their operation in AvtoVAZ cars is related to the lock, which often fails.

If the lock is broken

Models of the “tenth” series all suffer from broken handles. It is not known for certain why it breaks; take it as a design feature. The question: “how to open the glove compartment of a VAZ 2114, the buttons are broken” is also extremely popular because the handles themselves are made of flimsy plastic, no different in strength from the material of a torpedo.

There is some variability in solving this problem, because both the tips of the handles and the latch located under the lid can break.

In the first case, you are lucky:

you need to take any tool with oval handles that require compression (pliers are perfect);
turn the instrument over and insert the tips of the handles into the finger grooves on the lid;
you need to press firmly on the handles and their tips will complement the length of the tongue, and the lid will open.

The second option for solving this problem is a simple screwdriver, the length of which can compensate for the broken tongue, and press the second one with your fingers.

The glove compartment button is broken

If your internal latch is broken, then things will be much worse:

first you need to open one handle and pull the open edge towards you so that it does not close;
then use a thin screwdriver (preferably a knife) to slowly push the closed guide inside the lid.

How to remove the glove compartment on a Chevrolet Niva

The glove box must be removed to make it easier to disconnect the dashboard if you need to gain access to the fuses or controller and when completely disassembling the car.

Removing the glove compartment on a Niva-Chevrolet, work procedure:

Open the glove compartment lid, lift it slightly and remove the cords from both sides that hold it in place.
Using a Phillips screwdriver, unscrew the self-tapping screw from the side.
Using the same screwdriver, unscrew the two screws that secure the instrument panel console to the side.
We unscrew two similar screws from below.
Having opened the lid of the box, we unscrew two more screws on the left, again securing it to the instrument panel console.
We unscrew the screw located on the upper left mount, then on the middle and right (two).
We remove the lining from the box body.
There is one screw at the top right and two at the bottom, unscrew it.
We tilt the box, disconnect the lighting wire terminals. Disconnect the flashlight.

The glove box has been removed and installation is carried out in the reverse order.

Additional glove compartment Kalina

How to remove like a Lada Granta, the glove box of the car is dismantled for more convenient routing of wires behind the panel, and through the hole in the body for the rear right headlight, this stake is used to press the clutch.
Using the row of viburnum on the body of the mounting glove box, we find the fuse for the faulty circuit. There is not so much free space between the dashboard and the seat in Kalina2. Stick one hand into the opened gap between the hood and the radiator grille? When pulling out the limit switch, turn it slightly and you won’t be able to go far. If you open it all the way, it won't open. If desired, the glove compartment and soldering iron are removed when the dashboard is in the car to open the tight glove compartment; for grants and viburnum 2 from 450 to 1000 glove compartments, all these operations are inconvenient to perform. Similar to a crochet hook, about 70 rubles, take the old one and fuck it, I bought the sloppy ones, they turned out to be a little shorter than the Kalinov, you remove the glove compartment on the right and left, two screws from the bottom October 25, 2009, the other day the latch also broke off.

I disassembled it myself, as well as the trunk, and opened the stationery. So where are you talking? Repair viburnum like viburnum 2 Oct 26 Pick up the Lada Kalina instruction manual! The pieces of plywood are fixed using epoxy. There are only glove compartments and computer solutions to problems.

How to replace the glove compartment handle on a Lada Granta

The broken axis of the glove compartment lock looks like this. Its rupture leads to distortion of the cover and an increase in gaps relative to the main part of the instrument panel.

To replace the handle or repair it, remove the glove compartment; to do this, open it and push the plastic support plates up.

Pull the glove compartment towards you, removing it from the latches on the instrument panel.

The result of the work should be the following.

Thanks for subscribing!

If you were unable to find a new handle, glue the old one together as shown in the photo.

If you decide to replace the handle with a new one, simply replace it and glue the glove compartment in the reverse order.

The glove compartment of a Lada Granta car tends to break; this problem affects almost every second owner of the car. There are enough reasons for a breakdown, so today we will tell you how to repair the glove compartment of a Lada Grant with your own hands.

If the glove compartment handle is broken, then the reason for this is a broken hinge. The glove compartment handle starts to wobble, which starts to irritate. To eliminate the disease, you will need to remove the Granta's glove compartment and bring it home for a more detailed study. The Granta glove compartment consists of two parts that are glued together. Carefully separate them with a flat screwdriver.

Replacement process

Before you start changing the old element of the air purification system in the cabin, you should prepare the necessary tools in advance:

T-shaped wrench with curved handle (torx T-20);
positive screwdriver;
new air filter suitable for Lada Granta.

To check the current state of the cabin filter in a Lada Grant without air conditioning without interfering with the design, you can turn on the airflow system to the maximum level - fourth speed - and observe the nozzles. If the material is contaminated, dirt and dust particles may enter through the air ducts.

The step-by-step process of updating the filter element of the 8 valve Lada Granta is as follows:

For ease of operation, you can first raise the windshield wipers up.
Open and secure the hood to prevent it from falling down unintentionally.
Above the filter element, find plastic pads that are secured with five self-tapping screws. Unscrew them using a Phillips screwdriver.
Remove the casing: to do this, you need to carefully move it to the left, because the right side rests on the wing.
Unscrew the two screws that secure the air filter itself.
Remove the old cleaning element by unclipping it from the side clips.
Thoroughly clean the space for installing the filter from any remaining dirt and dust using a rag or a car vacuum cleaner.
Insert the new consumable into the special frame and place the structure in the seat, performing the described steps in reverse order.

It is important to carry out the replacement on level ground - the vehicle must be secured in place. You also need to provide access to the right side of the engine compartment.

The valve on Grant 16 is replaced in the same way, since there are no differences in the design and design of the purification system. Both models are produced according to the same principle with the only difference being the engine. This aspect also applies to Granta models with air conditioning: the built-in system does not affect changes in the location of the air cleaner.

Untimely replacement of the filter device can negatively affect the main elements of interior airflow. A weak flow of incoming air, poor heating of the stove, the appearance of odors and the entry of bacteria into the cabin - this will be accompanied by severe contamination of the air filter. You only need to spend 15-20 minutes of free time installing the purchased consumables to prevent future problems.

How to properly remove the glove compartment on a Lada Granta

A handbag in a men's version is a car glove compartment. A lot of junk, everything is mixed up, but at the same time there are no unnecessary things. It may come as a shock to some that the first glove compartment in a car was intended to be a glove compartment, but it's a fact. Now you can find everything there except the clothes for your palms. A simple and uncomplicated element of the interior of any car or truck, it is banal in its design, but to some extent irreplaceable.

Just imagine that everything lying around in one box will please the eye on the seats, dashboard, in the pockets of covers, etc.

Horrible! Therefore, it is very important to keep the glove compartment in good working order and not allow irritating sudden openings of the door at every jump on “smooth” domestic roads

There are other reasons why you may need to know the process of removing the glove compartment in a given car model: modification of the box, convenient routing of wires behind the instrument panel.

The removal process is very simple. It is enough to do it once, and you will forever remember how to do it.

Common faults

The most common malfunction of the glove box is a loose or rattling lid. You can repair the cover yourself; you don’t need any special knowledge. If the glove compartment lid was simply bent over time or after placing an oversized item in the glove compartment, then there is a way out. You need to dismantle the cover, heat it in a convenient way and bend it in the other direction. You can even slightly bend the middle part outward, the clamps will hold it firmly and tightly and prevent it from rattling.

How to remove the glove compartment on a grant

Grant's glove compartment upholstery

The glove compartment of the Lada Granta FL car is an ordinary, unlined plastic box. Whatever you put there, everything will jangle and rattle on the uneven road. Let's try to solve this problem ourselves. And the appearance will only benefit!

Traditionally, glove compartments or, as they are officially called, glove boxes, on domestic cars do not shine with practicality. So on the new Lada Granta, despite the original two-level design, it is the most ordinary hard plastic, not sheathed or pasted over.

What can you do, the Lada Granta is positioned as a budget car. However, such a glove compartment is also typical for most foreign cars in the low and middle price range. Therefore, rattling and rattling of contents on bumps is inevitable. You can fight in different ways: some put rags, some use the glove compartment solely as a document storage, some keep it empty altogether. But these are all half measures. The problem needs to be solved radically, which is what we will do now.

First of all, the glove compartment, or rather its lid, the inside of which acts as the glove compartment drawer, must be removed. The lid is held on by four latching hinges, as well as two opening stroke limiters. To remove it, open the glove compartment as much as possible, and then pull the lower part towards you parallel to the floor, releasing the latching loops. Photos with the cover removed will help you understand the design of the fastening and the direction of application of force.

After all four latching hinges are released, the lid remains on the opening travel stops. These are simply two pins of the lid that fit into the slots on the inside of the glove compartment.

Replacing the glove compartment handle of a Lada Granta

Results

If the airbag has deployed, operating the car or doing it yourself often leads to tragedy on the road.

To eliminate problems, you should contact an authorized dealer, who, after a complete diagnosis, will replace the failed elements.

Otherwise, there is no guarantee that the airbag will work in an accident and save lives.

Airbags are one of the effective components of a car's passive safety system. Its main task is to almost instantly reduce the speed of the person in the cabin. Thanks to this, during an accident you can avoid traumatic impacts and save the life of the driver or passenger.

Purpose and operating principle of SNPB

The airbag system is an additional means of protecting the driver wearing a seat belt and is designed to reduce the severity of his injury during frontal (±30 degrees) vehicle collisions in traffic accidents. SNAP is triggered depending on the force of the vehicle’s collision with various obstacles. In case of normal activation in an emergency situation, the SNAP is launched regardless of the state of the driver's seat belt fastening. Therefore, the use of a seat belt by the driver is a prerequisite for the effective operation of the air safety system.

The airbag system begins to function after the ignition is turned on and is controlled by an electronic unit (BUSNPB) with a self-diagnosis function. The system is activated by submitting an electrical signal from the BUSNPB to the airbag module.

If the airbag is activated, the upper part of the cover of the facing module of the airbag, when the airbag is filled with gas, breaks in structurally defined places and opens into two or three parts. Through the resulting opening, the gas-filled airbag bag deploys in front of the steering wheel or instrument panel. The filling time of the pillow is about 30-40 ms. After the airbag inflates due to excess pressure, the gas escapes through special holes located in the rear of the airbag bag, thereby preventing the driver or passenger from colliding with parts of the vehicle's interior and at the same time softening the severity of the impact of their head and chest.

SNPB device

The LADA 2190 car in the “Norma” configuration is equipped with a single-channel SNPB, which includes:

gas generator module (MNPBV) (part 21910-8232010-00);
airbag system control unit (part 21900-3824010-00);
connector with rotating device (part 21700-3709315-00);
steering wheel (part 21910-3402018-00).

Airbag system:

driver airbag module;
installation location of the SNPB control unit.

The gas generator module (MNPBV) consists of a gas generator 1, a housing 7 with an inflatable cushion folded in it, a facing cover 9, a sound signal switch and fasteners.

Gas generator module (rear view):

gas generator;
hooks for fixing MNPBB;
horn switch contacts;
hooks for fixing MNPBB;
location of the identification label;
gas generator igniter connector;
a body with an inflatable cushion folded in it;
hooks for positioning MNPBV;
facing cover.

The gas generator produces gas inside the module to inflate the airbag. The pyrotechnic substance located in the gas generator is ignited by a fuse-igniter mounted in the gas generator housing. There are two main types of gas generators. A pyrotechnic gas generator consists of a housing filled with a solid pyrotechnic substance and an igniter. In it, gas is produced when a pyrotechnic substance is burned. Used in the driver airbag module. A hybrid gas generator consists of a housing filled with compressed inert gas and a pyrotechnic substance, and an igniter. Used in the passenger airbag module. An igniter is a device with electrical resistance and a pyrotechnic substance. After receiving an electrical signal from the BUSNPB, the electrical resistance heats up and ignites the pyrotechnic substance of the igniter, followed by ignition of the bulk of the pyrotechnic substance of the gas generator.