✅ How to open the hood of a VAZ 2115 without a cable

Comments: no Published: 12/05/2016

Rating:

Tags:VAZ 2114VAZ 2115

In practice, emergency situations often occur when the cord of the mechanism responsible for opening the hood breaks. The hood release cable is designed to allow this operation to be performed from inside the vehicle. Beginners often have a question about how to open the hood of a VAZ 2115 car if the cable has come off or is torn. In this case, many are interested in how to replace the hood cable.

There is nothing complicated in these procedures - any novice motorist can handle them, even if he is new to taking care of his car. But you will need information on how to approach this procedure, where to start and how to finish.

Opening the hood on a VAZ 2114
See also:

Replacing the hood cable of a VAZ 2107

How to open the hood of a VAZ 2115 without a cable

I haven’t written anything for a long time, because...
I stupidly poured gas and checked the oil, but then the hood didn’t open, well, I think that’s it, we’ve arrived, the cable broke, I pulled the handle and the cable came out into the cabin by 5-10 cm, well, I think I’ll have to open it anyway! I surfed the Internet in the evening, in general here some are capable of anything, some tore out the plastic protection, some used jacks, there were even options with a grinder o_O in general I decided that there was most likely no more humane way than to climb through the bottom... last night after work I rolled it into the pit and then it began... I removed the pallet I removed one sheet of protection from side of the left wheel, (4 screws) I put my hand between the radiator and the engine, felt the pin (No. 3) and tried to unscrew it, but the evening was spent on it and without success

Today I climbed behind the light, somehow shone a flashlight and noticed that the spring (No. 21) that holds the cable was hanging like snot on the fence, in general, I asked my father to press the hood, meanwhile I used a screwdriver to pick out the remaining piece of the spring from under this pin, and he opened the hood! =)

I immediately ran into a nearby store and bought this spring for 5 rubles (at a discount) =) and put the torn pan on the rivets...

Conclusion:

If the cable does NOT come out completely into the interior, then most likely the problem is in the spring, if the cable came out, but there is a chance that it broke in the interior and can be removed with pliers, well, this is in the best case. Otherwise, we stupidly climb through the bottom, unscrew the pin and rejoice)

The hood of any car is designed to protect the engine, ignition system, and other components and assemblies located in the engine compartment. In addition, it also performs an aerodynamic function, allowing air flow to flow freely around the car while driving. It opens directly from the interior of VAZ cars using a cable and a special lever. In the case when they or the hood lock break, the car owner has a question: how to open the hood on a VAZ 2107?

It is worth noting that the design of the locking mechanisms of the hoods of VAZ cars allows you to repair them yourself. This does not require special knowledge or special tools. It is enough to study the instructions for carrying out such repair work and strictly follow the points set out in it.

Why won't the hood open?

The hood of a car may not open for several reasons. For example, his lock may become damaged. In addition, due to mechanical damage, for example during an accident, the hood and engine compartment are deformed. This may also make it impossible to open.

If we talk about the most common reason for this phenomenon, it is a banal break in the metal cable that drives the hood locking mechanism. A cable can break for various reasons, the main ones being: wear, corrosion on the surface of the cable, or excessive force applied to it. In the case when the cable is broken, the owner of a VAZ car can open the hood on his own, as this is a relatively easy procedure. In all other cases, it is quite possible that you will have to involve professionals in the repair work.

How to Open the Hood of a VAZ 2115 Video

Open the hood of a VAZ-2114 if the cable is flying (video inside)

So, we imagine a situation where a motorist decided for some reason to open the hood of a VAZ-2114, for example, by removing the battery or measuring the oil level, when the engine compartment cable breaks. A novice car enthusiast will stand and scratch his “turnip” or other interesting places, but an experienced one will know what to do right away.

Video of the hood opening when the cable flies away from the lock

The video will show you exactly how to open the hood if the cable is loose or torn, and it will walk you through some of the intricacies and nuances of the process.

Causes of failure of the hood opening cable

General view of the hood cable

Before moving directly to the issue of opening the hood without a cable, let’s consider the causes of the breakdown:

Carry the cable yourself. Quite a common reason for cars of the 13-15 Lada series. Frequent opening of the hood leads to this effect.
Cable corrosion can also lead to relaxation of the metal from which the product is made. This interruption cannot be prevented.
Flying hat In this case, it is also necessary to open the engine compartment without resorting to the cable.
Other reasons that the hood release cable used to break.

How to open the hood of a VAZ 2108 2109 21099 2113 2114 21

How to open the hood of a VAZ

-2108.
2115
Do not cut the hood with a meat grinder or twist it. I'm on:

How to open the hood of a VAZ 2115 if the cable flies off. Replacing the hood cable

Actually I thought the cable broke the hood

on my
VAZ 2115
. It turned out to be easy to fly away. But since I bought a new one, I decided.

Learning to open the hood

First, let's look at what to do if the handle responsible for this operation dangles freely without encountering resistance, which means the cord has fallen out of place or has broken.

If the break occurs inside the car, you are in luck - just find the end of the cord, grab it with pliers and pull it towards you. After the hood opens, remove the end of the cord from the lock spring. Now you will need to remove the loop at the handle, loosen the fasteners that are located in the engine compartment, and remove the broken cable out.

If the break occurs in the engine compartment, you will have to work hard. The opening procedure in this case is as follows:

Place the car over the inspection hole and go down;
Remove the engine protection mounts - these are several self-tapping screws that can be unscrewed using a size 8 wrench;
Remove the engine protection - it blocks access to the engine compartment;

Remove the engine protection

Make sure the engine is cool and stick your hand into the space between the engine and the radiator;
Find the lock spring by touch and move it towards the battery;
Now you can open the hood and release the cord from the lock.

After you have solved the first problem, proceed to the second - replacing the cable, this is also not difficult.

If for some reason you are unable to cope with the opening procedure, experienced motorists recommend taking radical measures. If the radiator grille is made of plastic, break it with a fist or hammer. Then you will gain access to the engine compartment and be able to open the hood.

And the radiator grille is inexpensive - you won’t have to spend a lot of money buying a new one. Of course, this option is useful as a last resort, if it is not possible to resolve the issue using a more competent method.

Other breakdowns that may lead to major repairs

It is important to know that the hood of the VAZ 2114 is not the only problem area in the car. In addition, the driver may encounter other difficulties that may lead to the repair of VAZ 2109, VAZ 2108, VAZ 2115, VAZ 2114.

The VAZ 2114 often encounters some minor damage. Every driver of such a car has at least once encountered the fact that the door handle breaks in his hands, especially on the driver's door. Frequent use of this pen resulted in constant repairs. Previously, such cars could be found in taxi services, and there was discomfort for passengers when they had to enter the salon only through one door, because the handles on all the others were broken.

Another problem that plagues motorists with domestic cars is stove failure. In a VAZ 2114 car, the stove always heats perfectly, even in the coldest winter. This is due to the fact that domestic car manufacturers tried to adapt their invention to all regions of the country. But in such cars the stove can break down at any moment, so you should always be prepared for its breakdown.

Another minor damage that plagues domestic VAZs is a breakdown of the glove compartment; sometimes it simply does not close, and drivers are already accustomed to leaving it open. The locking mechanism in the glove compartment, which is responsible for opening, stops functioning; it can become jammed. In order to open it, you need to make an effort. According to statistics, not every driver is in a hurry to repair the glove compartment lock.

What to do if the VAZ 2114 breaks down

It's always unpleasant when a VAZ 2114 breaks down. For some reason, modern domestic cars are more prone to breakdowns than foreign cars. There are usually incidents that are difficult to predict. If we talk about the VAZ 2114 model, then a problem in such cars can arise at the most inopportune moment. The car suddenly breaks down and you have to look for an emergency exit.

The most common problem in domestic cars is that the hood does not open. A common breakdown is that it closes tightly, but this problem often occurs on VAZ 2109, VAZ 2108, VAZ 2115, VAZ 2114. Therefore, it would be appropriate to consider this difficulty in order to know how to open the hood of the 2114.

Replacing the cable

After the hood lid has been successfully opened, you need to install a new mechanism cable. To do this you need:

Buy a new cable. In the store you can find two versions of its design: single-core and stranded. We recommend using the second option, as it has increased strength, service life and reliability.
Next you will need a cord, which should be tied to the end of the cable in the hood.
From the interior side, pull the old cable and insert the cord into the interior. At the same time, replace the O-ring in the body through which the hood mechanism element passes.
Similarly, tie a new cable to the cord and pull it out into the engine compartment.
Attach it to the lock and to the handle in the interior.
Be sure to check that the mechanism is working properly.

Learning to change the cable

Replacing the hood cable for VAZ 2114 and VAZ 2115 look identical. This is a simple procedure that is followed in the following order:

Buy a new cord. There are single-core and multi-core cables on sale - the latter option is preferable, since several turns are much more reliable. With this option, you will be insured for a long time against new hassles with opening and replacing the cable.
Tie a thin but strong string to the end of the broken cable in the engine compartment.
In the cabin, remove the hood release handle and pull the end of the old cable towards you - the cord will be pulled into the cabin.
Replace the O-ring.

Ways to open the hood if the cable breaks

The design of the hood, lock and location of the cable drive differs on cars. But the repair sequence remains the same in all cases. Owners of domestic brands are luckier, since manufacturers have not made significant changes to the design of cars produced over many years. Therefore, you can always open the hood without any problems.

Most often, the cable breaks near the lever, less often under the hood. In the first case, it is easy to deal with the breakdown, but in the second you will have to tinker.

When the cable breaks in front of the lever

This is the simplest situation. To eliminate the breakdown, inspect the place inside the car where the cable and the hood opening handle are attached; the stopper may have fallen off the lever - insert it into place and secure it. If you notice that the cable itself has broken off, then you will need pliers. To open the hood, try to firmly grasp the cable together with the casing and pull down. It may not work the first time. If a breakdown occurs, cut the hood and wrap the metal cable around the pliers, and then pull with great force - the hood will open.

conclusions

The design of VAZ cars has some outdated elements that have not been used on modern car models for a long time. These include the hood release cable. If it breaks, its cover will jam and the car owner will have to open the engine compartment. This procedure is relatively simple and can be done independently, although you will have to spend quite a lot of time. In order to prevent such an unpleasant situation from occurring, it is necessary to modernly replace the cable, and also try not to apply significant physical effort to it.

If you're lucky

First, remember: if the cable breaks, do not try to open the hood by force. This will only make it worse, because the metal where it joins the body is not the thickest. Let's first consider an easier case. Regardless of whether it is a VAZ-2114 or a VAZ-2109, you need to open the hood, as you know, from inside the car using the handle. So, if the cable breaks right next to it, then you can untwist it and pick up its tail with pliers. Then pull it towards you and the hood will open. Both on the VAZ-2115 and on older models the scheme is the same, so do not immediately rule out this option. Actually, after you have opened the hood, you can begin the repair, so that after everything you don’t have to climb for pliers again.

For repair, in fact, you only need one part. Carefully remove the broken cable from the fastenings and install a new one in them. The hood will open normally. The only detail: it is better to ask someone for help to press the spring of the mechanism while you attach the other tail to the handle. Then the cable will be tensioned better.

What is diagnostics of VAZ 2114

To solve problems, they diagnose the car, especially if it is a domestic car.

In addition, diagnostics are also intended to prevent various malfunctions; after such a procedure, the machine will not break down again.

With the help of on-board computers, many malfunctions can be prevented, as well as making it easier for the owner to monitor the general condition of the car. To do this, as a rule, you will need a laptop and some knowledge and skills in using software. The driver will have problems understanding the entire diagnostic system only during the first time of using the car. It is usually difficult for older drivers to carry out diagnostics; it is easier for them when it is done at a service station.

The VAZ 2114, like other cars in this line, are not ideal, but they have a number of advantages that foreign cars do not have. Even if the VAZ breaks down, there is no need to panic, the mechanics know the solution to any problem, especially since spare parts for such cars are easy to buy, including the aforementioned door handle or hood cable.

Domestic cars require delicate care. Although such cars break down, they can nevertheless be repaired an unlimited number of times, which is why cars that were produced a long time ago still drive on Russian roads.

Source: korchim.ru

If the cable breaks

In order to correct the situation in which the hood of the VAZ 2114 does not open, you need to drive the car onto an overpass or inspection hole and have on hand:

pliers;
keys used to remove engine protection.

First of all, it is necessary to inspect the cable for a possible break. There is a possibility that it broke somewhere in the cabin. Using pliers, the inner part of the cable is caught, but you just need to make sure that the element itself is grabbed, and not its braid. The cable is pulled towards itself, and after that the hood should open. But this method is only suitable for those cases when the break occurred inside the cabin.

For those cases when the cable breaks not inside the cabin, but under the hood itself, it is necessary to proceed using a different method. Here the repair will take place from below the car, so that it is possible to reach the hood latch. To do this, it is necessary that the car is standing on an overpass, or the repairman should be in the inspection hole. This way, work with the bottom will take place in more comfortable conditions. Using two keys, the crankcase protection on the engine is removed.

Next, the boot is removed from the engine. To do this, it is removed from the mounts that are located in front. The anther is bent back. Afterwards, using a screwdriver to penetrate the space next to the radiator, you need to reach the hood lock. There you need to feel the latch, which should be turned to the left, while pressing hard on it. The lock should open.

It is very important to monitor all parts of the car. Therefore, the hood latch must be lubricated regularly. To make the cable suffer less from constant use, it should sometimes be treated with silicone grease on the inside of the braid. Thus, the risk of rupture will be reduced several times. If the described methods do not help to open the hood, you will have to seek qualified help.

Before setting off, it would be a good idea to inspect your car. After all, if troubles start on the road, it can cost a lot. Therefore, those mechanisms that are responsible for safe operation should be inspected first. The hood, as a component of the car, protects the engine from environmental influences. To do this, the element in question is made from high-strength materials, most often steel.

Its outer side is covered with a layer of paint, which is designed to protect the hood from moisture. Opening the hood can be done with your own hands, or you can use special devices. There is another method that can help cope with the trouble that has arisen.

As mentioned above, to make such a repair, the car is driven onto an overpass, after which the boot and protection are removed, and access to the cable is provided.

Next, you need to determine the side of the hood opening, that is, in which direction to pull the cable. If you pull it towards you, it will change its location and this will make it possible to open the hood using the installation tool.
If it is not possible to place the car on an overpass, you can use a jack to ensure that you can work on the bottom of the car. The front of the vehicle is raised. To protect yourself during repair work, place logs or reliable bars under the wheels. In this case, even if the car falls off the jack, it will not be able to crush the person lying under it. It is advisable to lay a mat on the floor to make working more comfortable.
A homemade hook is made from wire. With its help, the lock spring clings and pulls towards the engine.
An important point is that the locks may have slightly different designs. Especially if the car had a different owner. After all, he could make his own adjustments to the arrangement of his “friend.” For example, install a hood gas stop, and then the problem may be not so much in the lock itself, but in the jamming of the stops.

In newer models, the issue of cable breakage has long been resolved. They have a spare cable that allows emergency opening of the hood or gas tank.

If the cable breaks in the engine compartment, you cannot do without an inspection hole

So, in order to answer how you can open the hood of a VAZ-2115 car with such a problem, let’s first take a closer look at this emergency situation. So, the driver, who for some reason intends to gain access to the engine, habitually pulls the corresponding handle in the cabin. However, instead of a certain resistance and the characteristic sound of the lock opening, he is surprised to notice that there is none of this. The handle has free movement, and the lock does not respond to all manipulations with the usual opening.

Solving this problem is actually not very difficult. If the break occurred directly inside the car, then in order to open the hood of the VAZ-2115, it will generally take literally a minute. We can consider ourselves lucky. The thing is that in order to open the hood, you just need to find the end of the broken cable and use pliers to pull it in the direction “towards you”. Half the battle is done - you will hear a characteristic sound, signaling that the lock has opened. This means you can move on to the next stage of troubleshooting. Open the hood and remove the end of the broken cable from the lock spring. After this, it remains to perform a few simple manipulations:

remove the loop located near the handle;
loosen the fastenings located in the engine compartment;
remove the broken cable.

As you can see, there really is nothing complicated. A more complicated option is a cable break somewhere in the engine compartment. In this case, you are again faced with searching for an answer to the question: how can you open the hood of a VAZ-2115? If you want to fix a malfunction without damaging the car, then in this case you cannot do without an inspection hole. All necessary manipulations to fix the problem must be done from below the car. So, let's look at the sequence of actions.

First of all, as mentioned above, you should go to the inspection hole. Next, we proceed to remove the protection.

One point should be noted here. If it is standard on your car, then to remove it you will need to unscrew several screws using an 8 key. Take a close look at their location:

4 self-tapping screws are on the front;
2 more - in the middle of the most standard defense;
the last 2 are in the spar area.

If there is enhanced shock-resistant protection, then the algorithm of actions will be slightly different. It is held in place by two crab bolts that press the fastenings of the part itself. Accordingly, they need to be unscrewed.

After the protection is removed, you gain access to the engine compartment, albeit from below. Before proceeding to the next step, be sure to ensure that the radiator has cooled down sufficiently. It is best to operate with hands protected by gloves. In order to open the hood, you will need to perform a few simple manipulations. In particular, you should stick your hand up, placing it between the engine and the radiator. After this, reaching up to the level of the lock, feel its spring and slide it towards the battery. That's all - you can open the hood and remove the remains of the broken cable. Before this, of course, do not forget to install the protection in its original place.

However, there is another, more radical option. However, it should be used only in cases where there is no way to perform the manipulations described above, and you need to get to the engine compartment very urgently. In order to open the hood if the cable breaks, you can simply break the radiator grille using an appropriate object, for example, a hammer. It is made of plastic, so there should not be any problems here. After this, you will be able to get to the lock and move its spring to the side, thereby releasing the hood.

It is clear that this option should be used only as a last resort, when there is simply no other way out. Indeed, situations when you urgently need to get to the engine compartment somewhere right on the road arise quite often, and there may well be no time to search for a hole. Accordingly, if the cable is jammed, break the radiator grille. It is not that expensive, while a situation may well arise where a delay in eliminating a malfunction in the engine compartment can lead to more serious consequences. Still, the main goal of any car owner is repairs with minimal financial losses, including without causing any damage to his iron horse.

Source: ladaautos.ru

Replacement procedure

So, it was possible to open the hood on a VAZ 2114 or VAZ 2115. Now you can do the actual repairs:

First, go to the store and pick up the product you need to replace. Multi-core cables are more expensive than their single-core counterparts, but they are also more durable - it is recommended to take this point into account when choosing.
Find the end of the torn product, which belongs to the interior part, and tie a cord to it. Remove the handle and pull the resulting system towards you - the cords will be pulled into the interior.
Repeat the procedure in reverse order - tie a new cable to the cord from the interior and pull it into the engine compartment of the vehicle.
Now you can connect the new product with the handle and the locking mechanism.

All that remains is to check the functionality of the new system, first of all, for the reliability of the connection, and you can continue to operate the car.

Opening the hood if there are problems with the cable

There are two ways to open the hood of a VAZ 2114 or 2115. The first, when the car owner was incredibly lucky and the hood cable broke directly inside the vehicle:

Locate the end of the damaged product;
Grasp it with something convenient - most often in this case, ordinary pliers are used;
Pull the product towards you - this will allow you to open the hood and begin a full repair.

The second option is much more complicated - the hood cable broke, but the location of the damage turned out to be inaccessible to the car enthusiast. In this case, to open the engine compartment on a VAZ 2114 or on another model from the same manufacturer - VAZ 2115, you will need to perform a more difficult procedure:

Move the vehicle to the vehicle inspection pit.
Using the key to “Eight”, dismantle the protection of the power unit, which will allow a person to have somewhat limited access to the desired compartment of his car.
Before continuing work, it is recommended to check the temperature of the engine - if it is hot, you can easily get burns if the unit comes into contact with your hand.
After this, you need to put your hand into the space between the car’s radiator and its power unit, feel for the special spring of the locking mechanism and move it in the direction of the car’s batteries.

If everything is done correctly, the car hood should open easily. Unfortunately, sometimes in the procedure described above a person experiences certain difficulties and cannot carry out his plans. In this case, you can do something a little differently, however, this will require physical destruction of the radiator grille, which will allow easy access to the locking mechanism. Naturally, a deliberately broken product will have to be purchased and installed again.