Recommendations for self-installation of fog lights on the Lada Granta liftback


A car equipped with fog lights will come in handy for traveling in conditions of limited visibility, fog and other adverse weather conditions. Another important step will be the proper installation and adjustment of these external lighting elements. Despite the fact that fog lights were not installed from the factory in all trim levels of the Lada Grant, installing them yourself will not be difficult.

Read about how to correctly and safely implement fog lights on a Lada Granta into your lighting system with your own hands and get tangible results from all this, read below in our material.

Preparatory stage (selection of PTF for Lada Granta)

The range of PTFs is not large; it is represented by several domestically produced models. Some owners claim that PTFs from Opel and Ford are compatible, but the information has not been verified.

Name / manufacturer / articlePrice, rub.)
LADA Granta (VAZ 2190) / Kalina 2 / LADA Largus
OSRAM Kit 21900-3743010
from 2800
Kit 21900-3743011—/—
—/— 2190-3743011—/—
—/— 2190-3743010—/—
PTF wiring kit for LADA Granta (2190 2874498)from 600
PTF "LUCH" set 1118-3743010/11from 1800
PTF glass (02B08507) Granta / Kalina 2 / Largus, Datsunfrom 750
AUTOMOTIVE LIGHTING / BOSCH (982469641)from 2000

*prices are as of September 22, 2018.

Tools and accessories

In order to install fog lights on the Grant, you will need the following tools and accessories:

  1. PTF kit for installation on Lada Granta or Kalina cars.
  2. Electrical kit to connect lighting lamps.
  3. Phillips and flathead screwdrivers.
  4. A screwdriver and a small drill. Its diameter should be no more than 5-6 mm.
  5. Stationery knife, wire cutters.
  6. A set of keys.
  7. Round file, fine-grained sandpaper or other tool for cleaning surfaces.

In addition, you may need to have a multimeter, scissors, electrical tape, and heat shrink insulation.

Procedure for self-installation of fog lights on a Lada Granta liftback


We place the car on a flat platform with access around the perimeter.

  1. We dismantle the front bumper along with the radiator grille.
  2. Using a milling cutter, we cut holes in the openings for the PTF.
  3. We install the fog lights and secure them to the fasteners.
  4. We connect the blocks with wires.
  5. Reinstall the bumper. We check the functionality of the system.

How to resolve the issue

The problem can be solved in two ways:

  1. Or purchase a new bumper with holes already cut out. For example, from companies involved in tuning AvtoVAZ models; (see also the article Fog lights for Kalina: what a car owner needs to know)
  2. Or you yourself cut out the holes for the fog lights on the Grant - installation, accordingly, will also be done by yourself.

Note! The purchase option is justified only if the technical condition of the standard one is unsatisfactory - cracks, chips, broken seats and broken latches.

Experienced car owners advise cutting holes in the bumper themselves. The rest of the story will be about how to install fog lights on a Grant yourself.

Step-by-step process for preparing and installing fog lights

In the auto store we purchase: PTF, corrugation (at least 3.0 m), adapters - adapters for PTF with standard wiring.

Related link:

Comparative review of the technical characteristics of Grants Liftback, Renault Logan and Renault Sandero

  • To remove the front bumper, unscrew three self-tapping screws on each side, four plastic clips, three “10” bolts in the lower perimeter;
  • We remove the structure along with the radiator grille;

It is important to know!!! In the Norma and Standard models, there is no hole for adjusting the fog lights. The owners independently cut out a diameter of “8”. In the Liftback body modification, the opening is factory-made.

  • We cut out the opening for the fog lights along the contour, it is factory-made;
  • To make it smooth, treat the surface with a household hairdryer;
  • We fix the headlights on three standard mounts;
  • We connect adapters to each of the lamps, since the standard block with wires is short, its length is not enough;
  • We put on the front bumper, screw it in with bolts and plastic clips.

conclusions

As you can see for yourself, in order to carry out a competent and correct installation of the PTF on the Grant frets, great skills and knowledge are not required. You just need to strictly follow our instructions and maintain skill and patience.

The last step will be to adjust the PTF so that driving the car is safe not only for you, but also for all other drivers traveling in the opposite direction.

In the standard configuration Norma, Standard, Lux, Liftback, fog lights (hereinafter referred to as PTF) are not installed in the front bumper. Instead of accessories, plastic plugs are built in. Let's look at how to install fog lights on a Granta liftback step by step below.

Wiring diagram for fog lights Lada Granta liftback

Engine compartment

  • We lay an additional wire from the right PTF headlight to the left one. We solder it and bring it into the engine compartment to connect to the relay.
  • We fix the mass to the body at the place where the bumper is attached, maybe under the license plate, in the center.
  • Do not forget to lay all electrical wiring in a corrugated material made of fireproof material.

Interior of the Lada Granta liftback car

  • We lay the corrugated hose through the hole in the hydraulic corrector seal.
  • The connection is best made at the ignition switch. That is, when turned off, the headlights will go out automatically.
  • Open the glove box lid, press the side stops, and remove the lid.
  • We stretch our hand into the cavity and carefully squeeze out the block of two buttons for controlling the heated glass and PTF.
  • We power the minus from the heater button. Plus we won’t take it, since they will be activated at the same time.
  • We connect the positive cable and install the unit again.
  • We connect to the positive from the ignition switch unit (blue wire), it is located under the steering wheel.
  • Finally, we power the relay - regulator: ground - wire from the button - end to the PTF - plus to the ignition.

Related link:

Tuning Grants Liftback

In each specific configuration, the color scheme of the wire may differ. Read the diagram in the instruction manual for details. Classic colors: red, yellow, blue, brown. If you do not want to supply power through the ignition switch, the connection diagram is simplified with one less procedure.

Installation of PTF (photo instructions)

As you may have already noticed, the Lada Granta bumper is a single molded plastic form, in the body of which there are places for fog lights, hidden by plugs. The next step is to cut out these plugs.

  1. It's best to mark the location for the cutout first.
  2. This work should be carried out with extreme care and precision. In order to cut holes, you can use either a regular stationery knife or more professional equipment - a drill.

We cut out the hole as carefully as possible.

We clean all edges from irregularities.

We fasten the fog lights with bolts.

Installation of PTF via a separate button

In order to connect fog lights on a Lada Granta, you do not need to buy the entire set of wiring, relays and additional parts from scratch.

You just need to take a special kit for connecting the PTF for Lada cars of the Kalina/Priora/Grant family. This kit includes all the necessary materials, as well as detailed installation instructions. Still, as a rule, the main drawback of this wiring is the short wires for the PTF power button, but they can be extended without problems by cutting in the required length of wires.

Everything you need is already included in this set.

The installation should be carried out strictly according to the instructions, leading the wires from the PTF directly to the mounting block, along the bumper and side member, laying the wiring to the button itself. It is important to secure all wires with plastic clamps and place the wires in a corrugated tube where they are subject to maximum wear.

PTF connection diagram

We make the connection strictly according to this scheme:

When connecting the PTF according to this scheme, everything is guaranteed to work.

The only disadvantage of this option for connecting the PTF will be the absence of a warning light on the instrument panel.

Step-by-step instructions for installing a rear fog light

Many Lada Granta Liftback car owners are surprised to hear about this, but it is a fact. Of course, we are not talking about PTF in its classic form, but about a laser brake light. It is installed in the rear of the car and informs the driver behind about the vehicle. Since there is no strictly defined installation location, it is customary to fix it in the area of ​​the license plate, under the lower contour of the bumper, in the spoiler. There are known cases of embedding an accessory inside.

A bright red light beam informs drivers behind, preventing accidents. The brake light is also used when it is necessary to notify the driver of the need to switch the high beam headlights. An alternative way to use lighting when backing up or parking in conditions of limited visibility. The maximum effective beam length is 25.0 meters. Exceeding the length does not guarantee the quality of lighting.

The voltage is supplied from the left/right brake light. Activation is possible either by pressing the brake pedal or by a separate button. The owner makes the decision based on personal beliefs. In practice, activation occurs with an autonomous button, since when driving backwards it is not always advisable to use the standard brake pedal. It is strictly forbidden to point the laser beam at the windshield area behind the driving driver.

Related link:

Soundproofing Lada Granta Liftback

Possible problems and malfunctions

The low beam of the Lada Granta does not illuminate the right side of the road well enough, so additional optics will be an excellent assistant and will provide a bright luminous flux.

During the installation process you may encounter the following problems:

  • crease in the corners of the wings when removing the bumper;
  • damage to electrical wiring terminals;
  • incorrect connection or short circuit of the wire.

The bumper on the Grant is made in the form of one large part, so during dismantling problems may arise in the form of damage to the front fenders, so you need to remove the bumper together with an assistant on both sides at the same time.

If nothing lights up when you test turn on the optics, the plugs are most likely damaged due to incorrect connection. To fix the problem, change the connector. If the lights come on for a second and then go off, this may indicate a faulty relay.

Fog lights device

The standard fog lights are equipped with a plastic mount that holds the optics in the Granta's bumper. The reflector design allows you to effectively illuminate the road surface due to its low location in the bumper and a wide horizontal beam.

There are several types of optics:

  • halogen;
  • LED

Classic halogen lamps are installed in all standard fog lamps of most cars. Parts made from diodes are not capable of producing a beam of the correct shape and efficiently illuminating the road in the dark. These fog lights are often used as daytime running lights.

The internal structure of the Granta headlight does not require the installation of gas-discharge xenon lamps. Traffic police officers may have questions about such systems.

Self-disassembly

Removal and disassembly of Grant foglights may be required in case of cracked glass or accidental water ingress.

For dismantling:

  1. Remove the bumper.
  2. Disable chips.
  3. Unscrew the fog light fasteners.

To remove the headlights without removing the bumper, you will need a lift and bending the fender liners. Disassembling the Lada Granta headlight will require the use of a cardboard box, an industrial hair dryer and a flat-head screwdriver.

To open the headlight you need:

  1. Place the parts in the box and close the lid.
  2. Cut a hole on the side and set the hair dryer for 5-7 minutes.
  3. Remove the headlights and carefully pry out the glass with a screwdriver.

To thoroughly wash a dirty reflector, disassemble all internal parts and wipe with an alcohol wipe.

New glass is installed using black or clear sealant, depending on the shade of the headlights.

Reviews

Positive
1.Kirill , 36 years old: after purchasing a Lada Grant from the showroom, I immediately purchased a PTF from OSRAM 21900-3743010. I didn’t install it at the service station because I can do it myself. In general, I am satisfied with the quality of lighting, no complaints.
2.Vitaly , 29 years old: it is obvious that there are not enough foglights out of the box. I often drive at night and need a good view of the road. Since I don’t understand manufacturers, I entrusted it to a specialist at a service station. PTF Lada Granta liftback - my advice.
3.Georgiy , 37 years old: I’ve been working as a taxi driver for the second year, my shift often ends after one in the morning. The disadvantage of the standard lighting system is obvious. I bought a “LUCH” set 1118-3743010/11 at the market. The cost is 1850 rubles, the quality is good, installation couldn’t be simpler.
4.Victor , 25 years old: I work as an entrepreneur, purchasing goods from hundreds of kilometers away. By morning the products should be on the counter. To help the standard headlights, I installed PTF. Second week, no complaints.
5.Maxim , 28 years old: I leave my positive review of BOSCH fog lights (982469641). Special thanks to the store manager for his practical advice.
6.Konstantin , 37 years old: during scheduled maintenance, he ordered the service of installing a PTF from a technician. I chose OSRAM 21900-3743010 because the price and quality are at a decent level. Numerous positive reviews.
7.Vladimir , 48 years old: I was a little upset by the lack of fog lights from the box on the Lada Granta liftback. I had to install it myself last weekend. The lighting is good, no complaints.
Negative
1.Alexander , 36 years old: not only are fog lights not included in the kit, but they also provide poor lighting. We are talking about a domestic manufacturer. Installed by BOSCH (982469641). I use it myself and recommend it to others.
2.Vitaly , 39 years old: installed domestic PTF OSRAM 21900-3743010. I regretted buying it, wasted money. The quality is below average, the angle of inclination is several degrees. I don't recommend it.
3.Vyacheslav , 37 years old: not happy with the installed fog lights, they don’t cover the side of the road, visibility is mediocre, the light is dim.

Conclusion Every product has its own buyer. If you don’t find fault with a budget car, which is the Lada Granta Liftback, the quality of PTF lighting is good, it is enough for visibility. Of course, when compared with headlights from foreign brands in the premium segment, the advantage of the latter is obvious. In order to increase the service life of accessories, purchase products exclusively from certified points of sale. Require the provision of documents, check the functionality on site.

Related link:

Review of mudguards on Granta Liftback. Installation recommendations

We stock up on everything we need

To install fog lights on a Grant, you will first need to assemble the required equipment:

  • fog lights – 2 pcs;
  • relay for 4 or 5 contacts with a capacity of 15A;
  • switching;
  • On-off toggle switch or external lighting control unit.

PTFs that are suitable for this car model are produced by two enterprises - Avtosvet in Kirzhach and Bosch in Ryazan. You can also purchase universal fog lights that will suit your specifications. Once you have purchased all the items from the list above, you can get to work.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]