Replacing lamps in the rear combination lamp (for use on the Lada Priora model)

f2

The location of the lamps in the rear lamp of Lada Priora cars produced since 2013 with sedan and hatchback bodies: 1 - turn signal lamp;
2 — fog light lamp; 3 — reversing lamp; 4 - LED block responsible for side lights and brake signal. Location of lamps in the rear lamp of Lada Priora cars produced since 2013 with sedan and hatchback bodies: 1 - turn signal lamp; 2 — fog light lamp; 3 — reversing lamp; 4 - LED block responsible for side lights and brake signal

The location of the lamps in the rear lamp of Lada Priora cars produced since 2013 with sedan and hatchback bodies: 1 - turn signal lamp; 2 — fog light lamp; 3 — reversing lamp; 4 - LED block responsible for side lights and brake signal

Removing and installing a rear light on a Priora

So, first of all, we open the trunk lid, and on the inside we find a special technological window with Velcro that needs to be opened. It is through this that you can get to the flashlight mounts.

It is worth noting that from the inside it is not mounted with bolts, but with special plastic screws that secure the lamp to the car body. There are three of them in total, of course, each of them must be unscrewed. After this, we move the lantern to the side from the outside, as is clearly shown in the photo below.

If it is necessary to replace the rear light, then each of the lamps should be pulled out of the light housing from its rear part. More on this below.

f1

The location of the lamps in the rear lamp of a Lada Priora car produced before 2013 with a sedan body: 1 - reverse lamp;
2 — side light and brake signal lamp; 3 — turn signal lamp; 4 — fog light lamp Location of lamps in the rear light of a Lada Priora car produced before 2013 with a sedan body: 1 — reverse light lamp; 2 — side light and brake signal lamp; 3 — turn signal lamp; 4 — fog light lamp

The location of the lamps in the rear lamp of a Lada Priora car produced before 2013 with a sedan body: 1 - reverse lamp; 2 — side light and brake signal lamp; 3 — turn signal lamp; 4 — fog light lamp

The work of replacing lamps is shown on the left headlight of a Lada Priora car produced in 2013. On the right lamp we perform the same operations.

To replace the lamps in the rear light, simply unscrew the nuts that secure it and move the light away from the body without disconnecting the light's wiring block from the rear wiring harness block.

Video on this topic

how to remove the rear light on a Lada Priora

Lada Priora station wagon: replacing the tabs in the headlights

I'll show you how to change the light bulbs in the headlights of a Priora station wagon

.

Removing the Priora station wagon lamp

Removing the rear light of a Priora station wagon

VAZ 2171.

how to remove the rear light on a Lada Priora , Everything is done quite simply. We bend the upholstery on the side to be removed.

LED in Priora, replacing stock lamps in reversing headlight

LED reverse lamps P21W on led.

Lada Priora station wagon : replacing the tabs in the headlights

I'll show you how to change the light bulbs in the headlights of a Priora station wagon.

Installing LED rear lights on Priora

Online store EXELET.RU Tolyatti, st. Ofitserskaya 12V, office 206 Tel https://exelet.ru PRIORA on Drive2.

Replacing a flashlight on a Priora

Replacing the headlamp on a Priora.

How to change the brake light bulb in the rear lights of a Priora hatchback

Our group in contact SIMPLE OPINION https://vk.com/ProstoeMnenie Become a YouTube Partner https://youpartnerwsp.com/join?9658 In the video.

Replacing rear light bulbs on a Priora | How to change turn signal and brake light bulbs on a Priora

Replacement of turn signal lamps, side lights, brake lights, rear lights on a Priora. We take the Lada Priora from the burnt one.

Replacing rear light bulbs on a Priora

Details on how to change the brake light, tail light and turn signal lamps in the tail light of a Priora hatchback.

Replacing the brake light bulb, tail lights and turn signals on Priora Hatchback and Sedan

Video review of replacing light bulbs in the rear lights on a Lada Priora hatchback.

The design and arrangement of the rear lights on a Lada Priora car are such that if it is necessary to replace one of the failed bulbs, you have to remove the light completely. It is logical to first consider the procedure for removing the rear light using the example of a Priora in a hatchback or sedan.

DS4 4556555

Pressing the lamp, turn it all the way counterclockwise and remove the lamp from the socket.
Pressing the lamp, turn it all the way counterclockwise and remove the lamp from the socket.

Pressing the lamp, turn it all the way counterclockwise and remove the lamp from the socket.

We install the new PY21W lamp in the reverse order. In this case, two protrusions, located asymmetrically relative to the axis of the lamp, must fit into the corresponding grooves of the socket.

We carry out the operations for replacing the remaining lamps in the same way. In addition to the black “ground” wire, each lamp socket is connected to other wires of different colors. In order not to confuse the lamp sockets when installing them, the corresponding wire colors are indicated on the lamp body.

Removing and installing a rear light on a Priora

So, first of all, we open the trunk lid, and on the inside we find a special technological window with Velcro that needs to be opened. It is through this that you can get to the flashlight mounts.

It is worth noting that from the inside it is not mounted with bolts, but with special plastic screws that secure the lamp to the car body. There are three of them in total, of course, each of them must be unscrewed. After this, we move the lantern to the side from the outside, as is clearly shown in the photo below.

DS4 45565557

For example, on the body of the light, next to the lamp socket socket, there is an inscription “orange”, corresponding to the orange wire of the lamp socket.
For example, on the body of the light, next to the lamp socket socket, there is an inscription “orange”, corresponding to the orange wire of the lamp socket.

For example, on the body of the light, next to the lamp socket socket, there is an inscription “orange”, corresponding to the orange wire of the lamp socket.

After replacing the lamp, install the rear light in the reverse order.

Changing the lamps in the rear light of Lada Priora

Replacing the brake light, tail light, turn signal lamp on a Priora

To remove one of the lamps, you need to grab its “socket” with your hand and turn it slightly counterclockwise. After which the lamp is removed from the base of the lantern.

Now, in the same way, we take the lamp itself, and turning it counterclockwise relative to the socket, we remove it.

Replacing the lamp is carried out in the reverse order. It is worth keeping in mind that when installing new bulbs in the Priora's taillight, you must adhere to the same rules as with the front headlights. That is, you should not touch the glass of the lamp with bare or dirty hands, otherwise this will lead to a decrease in its service life.

After all the necessary work has been completed, you can begin installing the flashlight in its place by tightening all the retaining screws and closing the special technological pocket with Velcro. The price of each such lamp is no more than 50 rubles, and if you replace the lamp, you will have to fork out for it, since you can buy it no cheaper than 1400 rubles for a standard factory-made DAAZ.

Difficulties with replacement

The most convenient thing is to replace the turn indicators. In other cases, you have to twist very tightly and stand in this uncomfortable position for a couple of minutes until the job is done. This is not very convenient, because the light bulb is a consumable, but the engineers could make sure that replacing it was as easy as the plastic steering wheel insert on the “ten”.

Another inconvenience is that you have to remove the battery. Nobody argues that it is better to turn off everything before starting work. But the battery is removed for reasons of rationality - the battery takes up a lot of space and interferes with working with your hands while you stand in an awkward position.

Manufacturers of lamps for VAZ 2114

Since lamps with an H4 socket are used in headlights of many models from different manufacturers, all manufacturers of car lamps produce such lamps. Among them are the following companies:

1. A world-famous Dutch company, known for its low prices and good quality products;
2. A German company with a long history and rich technological experience;
3. Narva. This is another manufacturer from Germany, known for the quality and durability of its products;
4. Bosh. Another German company that does not need any special introduction;
5. Company based in Hong Kong and Germany. Produces a wide range of reliable lighting equipment.

The above list can be continued for a long time. Today, a big name of a manufacturer is not a guarantee of high quality and reliability. There are a lot of fakes on the market, which are not only cheap, but also completely inconsistent with the original. Therefore, it is better to make a choice based not on the name, but on the characteristics of the light bulbs.

Types of headlights

The headlight unit on a VAZ can have two design options:

Outwardly they are very similar. Experts distinguish them by small details - the shape of the blender arches or the rotation diffuser. Kirzhach has a long, narrow reflector with a partition and no top wall. Bosch has walls on all sides, and the reflector is short. For an inexperienced person, it is easier to distinguish these designs by the shape of the plug on the back of the headlamp - Bosch products have one and are made in the form of an oval. These subtleties are not accessible to everyone, but only to experienced car enthusiasts.

Important! They have no fundamental difference in design, but installing one instead of the other will not work. Therefore, you should know which headlights will fit the body of a given car, so as not to find yourself in a difficult situation when purchasing

In addition, Kirzhach headlights are more difficult to disassemble than Bosch.

There are also Chinese analogues of headlight units for the VAZ 2114. They can have any shape, since they are not subject to general standards. Purchasing such products is a big risk. You can, with equal probability, get suitable headlights, or have lighting fixtures that do not match the shape of the sockets.

Installing LED tail lights on Priora

As for LED tail lights for Lada Priora cars, their prices are of course a little higher. Namely, a set of such lighting equipment can be purchased for around 3,200 rubles. As for installing a flashlight instead of a standard one, there is absolutely nothing unusual here.

It is necessary to disconnect the power connector for the flashlight, which is standard for all types of Priora, and then, after removing the old flashlight, install a new one with LED lights in its place. There is no need to perform any additional actions or manipulations. And the result of the work done can be seen in the photo below:

If you have any questions about the material provided, or have something substantive to add, please write below in the comments.

Replacing the brake light, tail light, turn signal lamp on a Priora

To remove one of the lamps, you need to grab its “socket” with your hand and turn it slightly counterclockwise. After which the lamp is removed from the base of the lantern.

Now, in the same way, we take the lamp itself, and turning it counterclockwise relative to the socket, we remove it.

Replacing the lamp is carried out in the reverse order. It is worth keeping in mind that when installing new bulbs in the Priora's taillight, you must adhere to the same rules as with the front headlights. That is, you should not touch the glass of the lamp with bare or dirty hands, otherwise this will lead to a decrease in its service life.

After all the necessary work has been completed, you can begin installing the flashlight in its place by tightening all the retaining screws and closing the special technological pocket with Velcro. The price of each such lamp is no more than 50 rubles, and if you replace the lamp, you will have to fork out for it, since you can buy it no cheaper than 1400 rubles for a standard factory-made DAAZ.

H4 car lamp tests

1. Which lamps are the brightest were determined by the Test Lab channel (June 2020). The rating is as follows:

1. OSRAM Night Breaker
2. Philips X-Treme Vision
3. Philips Vision
4. Philips Vision Plus
5. Philips Longlife Ecovision
6. OSRAM U37R
7. Narva
8. OSRAM Cool Blue
9. GE 50440U

Out of the standings:

• MTF Argentum
• OSRAM Super Bright

2. Test of H4 automobile lamps “Behind the Wheel” in the laboratory and on the roads (March 2022):

Layout of the restyled version

In the Priora, little has changed after restyling - small details invisible to the eye, the center console, the dashboard. The headlights have also changed - they have become quite a bit larger. The principle of their design has remained virtually unchanged, except that there is now one plug at the back to isolate the contacts.

The design of the headlamp unit has become more complex: now in place of the usual high beam lamp there is a light consumable, combined with daytime running lights, which switches between operating modes. PTF fog light bulb, everything is also mounted depending on the configuration.

Criterias of choice

The low beam of VAZ-2107 (Lada Priora) cars is implemented using halogen lamps. They have an H7 base and a power of 55 W. Similar lighting devices are produced by all car lamp manufacturers, both European and those from Southeast Asia. The most reliable companies producing H7 light bulbs include:

1. A Dutch company whose history goes back 120 years. The range includes a large number of different technical devices. Lighting devices make up only a small part of the total production volume. Famous for quality and reliability. Today the company has factories in many countries around the world;
2. Large manufacturer of automobile lamps from Germany. Initially, the company was a division of the Siemens concern. The production of lighting devices is the main specialization of the company, which has achieved great success in this direction. The company's subsidiary, Neolux, which also produces lamps and lighting equipment, is actively operating;
3. Another German company whose age exceeded 100 years. It produces a wide range of products; in addition to light bulbs, power tools and automobile accessories are widely known;
4. The company was founded in Germany in 1948. The production of electric lamps is the main direction of the company. All products undergo multi-stage quality control and have appropriate certificates;
5. Sho-Me. A large Chinese manufacturer of car lamps, accessories and other goods. Most xenon lamps are produced by this company;
6. MTF-Light. A Russian company that produces automobile lamps for the domestic market. Production facilities are located in South Korea. The products meet all international standards and are highly valued by users.

The above list is not exhaustive. It is difficult to list all the companies, and there is no point in doing so. New companies are constantly appearing on the market, offering their products to customers.