Which oil filter is better to install on the fret grant?

Similar materials

Oil change on Grant

To change the oil and oil filter yourself you will need:

• socket wrench or socket “17” or hexagon socket “8” (depending on the type of plug used)
• oil filter puller
• the filter itself and the engine oil

Before buying oil, find out what type of viscosity is most suitable for the climate in which the car is operated. If you live in the middle zone, for example in the central part of Russia or the Volga region, then you can use oil with a viscosity parameter of 10W-40; this parameter determines the possibility of using the oil in a temperature range from -25 to +40.

If in your region there are often frosts in winter with temperatures dropping below -30, then you need to use oil with a viscosity parameter of 5W-XX, which retains fluidity down to -35 degrees. In case of extreme temperature drops below -35, it is necessary to use oil with the 0W-XX parameter, which does not freeze down to -40. As for the base of the oil used, synthetic or semi-synthetic, we will leave this choice to the reader, since in this case the question is not only technical necessity, but also the cost of consumables.

The manufacturer previously used mineral oil as the first fill engine oil, which had a break-in status and needed to be replaced after 3 thousand kilometers, however, with a change in the technical process and maintenance regulations on the conveyor, semi-synthetic oil Rosneft 5W-30 is used, designed for a mileage of 15 thousand kilometers.

To most conveniently carry out the oil change process, you will need a pit, overpass or lift. Before draining the oil, it is necessary to warm up the engine to operating temperature so that the oil is more viscous and does not linger in the engine lubrication system.

For some time now, the plant used two types of engine oil sump plugs, the first had a size of “17” for a socket wrench, the second had a size of “8” for an internal hexagon. However, this applies exclusively to cars with a manual transmission and engines equipped with a steel crankcase; on cars with automatic transmissions, a cast aluminum crankcase is used and only “8” hexagon plugs are used.

We unscrew the oil drain plug with a suitable tool and drain it; to speed up the process, you can pull out the oil dipstick or oil filler plug to allow air into the engine

Attention! The drained oil is hot! It takes about five minutes to completely drain the oil.

It takes about five minutes to completely drain the oil.

It is worth saying a few words about the use of flushing oil or flushing compounds. They should be used either when changing the oil base or its manufacturer due to the characteristics of the additive composition in a particular oil, or every 30-50 thousand kilometers to prevent coking of the oil channels. However, any branded modern oil has good cleaning properties and therefore, if it is not overheated, it does not leave deposits harmful to the engine.

There are two types of washings themselves: quick and complete. A quick flush of the oil system consists of a small bottle of the composition, which is poured directly into the old oil before draining and the mixture is allowed to work for 5 to 20 minutes, according to the instructions. A complete rinse is a regular canister of mineral oil with a large dose of detergent additives. This flush is poured into the engine after draining the old oil and the engine should run at idle for the time indicated on the label with the canister. Then it merges in the same way.

Top 3. BOSCH 0 451 103 274

11 reviews from resources taken into account: Reviewer

The most reliable High quality and complete absence of counterfeits on the domestic market makes Bosch oil filters the most reliable products.

The Bosch oil filter, which is often chosen for the Lada Granta, causes a minimum of complaints from car owners. Thanks to the efficient operation of the drain valve and the small volume of the filter unit, instantaneous pressure is ensured in the oil system. Timely supply of lubricant after startup has a beneficial effect on the service life of the 16-valve internal combustion engine. Small sizes do not affect the degree of cleaning. The filter reliably captures dispersed particles even when using engine oil with extended drain intervals. The only drawback of the product is that it cannot always be purchased at retail.

Advantages and disadvantages

• 15 Best Oil Filter Manufacturers

General issues

Which clutch is better to install on a Granta
? Let's consider general common questions about Granta and oil.

How to check the oil level in Grant

We check the level classically;

1. The car must be turned off for at least 5-10 minutes;
2. We take out the oil dipstick, wipe it with a rag and put it back;
3. We take it out and look at the light - the level should be between MIN and MAX.

The dipsticks on the Lada suffer from the fact that they are difficult to read. You may need to wipe and lower the dipstick again.

If the dipstick is very difficult to read, you can go through the area indicating the level with fine sandpaper. This matting shows the oil level more clearly.

When to change the oil of a VAZ 2190

According to the regulations, replacement on the Grant is required every 15,000 kilometers. Practical experience suggests replacement every 10,000 km. mileage, or once/twice a year.

The Grants are stuffed with Rosneft from the factory. The brand has not proven itself to be reliable and of high quality.

The first replacement occurs after the new car has been broken in - after 2000 km. This is not a requirement from the factory, but common sense - change the flooded s to something normal.

Oil change on Grant

What racks are best to put on the grant?

To change the oil and oil filter yourself you will need:

• socket wrench or socket “17” or hexagon socket “8” (depending on the type of plug used)
• oil filter puller
• the filter itself and the engine oil

Before buying oil, find out what type of viscosity is most suitable for the climate in which the car is operated. If you live in the middle zone, for example in the central part of Russia or the Volga region, then you can use oil with a viscosity parameter of 10W-40; this parameter determines the possibility of using the oil in a temperature range from -25 to +40.

If in your region there are often frosts in winter with temperatures dropping below -30, then you need to use oil with a viscosity parameter of 5W-XX, which retains fluidity down to -35 degrees. In case of extreme temperature drops below -35, it is necessary to use oil with the 0W-XX parameter, which does not freeze down to -40. As for the base of the oil used, synthetic or semi-synthetic, we will leave this choice to the reader, since in this case the question is not only technical necessity, but also the cost of consumables.

Top 5. MANN W914/2

Affordable price, excellent oil pumpability and consistent “German” quality have made the MANN W914/2 filter system the most popular among Lada Granta owners.

According to reviews from owners of the 16-valve Lada Granta, MANN W914/2 is one of the best filters for this car. Pressure appears in the oil system almost immediately, and for an engine with two camshafts this means a lot. The quality of original products has been stable for decades. For this reason, many Granta users have no doubt which oil filter to choose: from time to time they take the “Mann” one and don’t worry about anything. The only thing that can overshadow the experience of using this product is encountering a fake.

Source

Design features of the “air filtration system” of 8 and 16 valve engines

What kind of oil to pour in Lada Grant 8 valves

The air supply elements in the 8 and 16 valve engines of the Lada Granta do not have any special design differences. Therefore, we will look at the process of replacing the air filter using the example of an 8-valve engine 21116.

Of all the tools we need, we will need moderately straight hands and a crosswise screwdriver. Difficulty: minimal. But the result can exceed all expectations. A clogged filter may result in loss of power and increased fuel consumption (factory fuel consumption data).

Replacement process with photo

1. Open the hood. The air filter housing is circled in red.
2. Remove the terminal from the MAF connector. You don’t have to remove it, but it’s more difficult. Disconnect
3. We take a screwdriver in our hands and unscrew the 4 bolts securing the air filter housing. These bolts must be unscrewed
4. We remove the old filter.Old filter
5. We clean the filter housing from the inside; most likely, there will be a lot of dust inside it, and there may also be dry leaves. You can use a damp cloth, just make sure that the lint does not remain in the filter housing after use.
6. We install the new air filter in the same way as the old one.
7. We assemble the body and screw back the 4 bolts. Screw everything back

Air filter life

The service life of the air filter is marked on its housing.

The service life of the air filter is 30,000 km.

This is the number indicated on the case. But it should be remembered that if the car is operated in poor external conditions, then this figure can be reduced. In this case, it is necessary to regularly check the cleanliness of the filter.

If you mainly drive on dirt roads, then replacement may be required after six or even five thousand kilometers. In desert areas the situation will be even more complicated.

Part numbers

There should be no problems purchasing an air filter. They are available in any self-respecting auto store. But just in case, we will write a couple of proven articles.

GB-9597 E4 - Big Filter - (146 rubles in total in the autodoc) One of the cheapest filters

Working principle of the air filter

Left - old, right - new air filter

Air intake usually occurs from outside the vehicle.

And, given that the conditions outside can be very different, sand, dust, pieces of asphalt and even pollen can get inside with the air.

All these inclusions do not allow the engine to operate properly. So, on the way from the air intake to the engine there is an air filter in which these particles are retained.

Most often, so-called dry air filters are used, which have the structure of a regular paper cartridge. As the practice of the automotive industry has shown, it is this filter format that has the best ratio of cost and degree of purification.

Air filter devices

The design of such a filter requires the presence of a plastic casing in which the cartridge is located. It, in turn, includes a frame with a special sheet of paper folded like an accordion. The paper should have a pronounced porous structure. And additional processing of the paper allows us to talk about reliable protection against moisture, which can damage ordinary paper products. And the peculiarities of the interweaving of cellulose fibers are such that air can pass between them, but anything larger than microscopic sizes will be retained.

Injection car models, as a rule, use rectangular-shaped filters, while carburetor options use oval and round shapes. The box can last quite a long time, but the filter element itself needs to be changed regularly.

Which air filter to choose?

The dry paper filter option we already mentioned is standard for most machines. But, sometimes, alternative options may be used. We are talking about liquid-type models that use mineral oil to purify the air. Moreover, in order to save money, you can choose already used material for the role of oil.

The key advantage of such filters is that you can change the oil as soon as the old one becomes too dirty. But the disadvantage of such filters is that they have a large mass, so they should not be used on modern cars.

Zero resistance filter under the hood of Lada Granta

Separately on the list are “zero resistance” filters, which have a special structure, but are built on the same type of paper. They are used on cars with a sporty "bias". This can significantly increase the engine power.

Top 2. LADA 2105-1012005-82

25 reviews from resources taken into account: Yandex.Market

The best combination of price and quality The domestic oil filter from the VAZ automobile plant has a better balance of performance characteristics and cost.

When deciding which oil filter to take as a replacement part, owners of an 8-valve Granta often choose a system from an official VAZ supplier. The model deserves a lot of positive reviews. Decent workmanship and efficiency of oil purification throughout the entire cycle are noted. The engine oil drained after use does not contain large fractions and is homogeneous - the filter reliably performs its function. The bypass valve eliminates oil starvation during startup, but Lada Granta owners often note that the pressure indicator sometimes does not light up immediately.

Advantages and disadvantages

• Always on sale
• Excellent filter element
• Good price

• The pressure in the system does not immediately increase

• 10 best batteries for Lada Granta

How to choose the right cabin filter

Autoreview experts tested 10 cabin filters in the Lefortovo tunnel and laboratory. They recommend following the following rules when choosing a cabin filter:

1. Buy a cabin filter only with the original article number.
2. The less the filter deforms in your hands, the better: the lower the likelihood of incorrect installation.
3. The filter material must have a laminated coating on the side facing the fan so that fluff from the filter does not enter the ventilation system.
4. The filter must be marked with the direction of air flow.
5. The carbon filter does not necessarily have to be sealed in polyethylene: activated carbon “works” only with air circulation, which is virtually excluded inside the box lying in a warehouse or store.
6. When the size of the box is much larger than the filter itself, this is not evidence of a fake. Many manufacturers prefer to save on packaging in this way: due to a smaller number of standard box sizes.
7. The carbon filter must be selected by weight: a heavier one should be preferred - it contains more activated carbon.

Test results of ten cabin filters

:

Bold

The filters that turned out to be better than others are highlighted.

As a result, experts came to the conclusion

that a regular (dust filter) filter saves on your own health. But activated carbon can soften the blow to your health from inhaling nitrogen dioxide and unburned hydrocarbons.

Keywords: Lada Kalina filters | Lada Granta filters | air conditioner Lada Kalina | air conditioner Lada Granta | Lada Kalina stove | Lada Granta stove

1

Found an error? Select it and press Ctrl+Enter..

The principle of rating construction

When choosing the best oil filter, you can only talk about a specific car. Our test object was one of the best-selling cars in Russia - Kia Rio 3 with a 1.6 liter engine. As a “reference point” we took the standard Kia oil filter number 26300-35503 , which is also used on many other Korean cars. Its mounting dimensions are almost standard by modern standards: thread M20x1.5, body diameter - 78 mm (outer diameter of the sealing ring - 63 mm). Having selected the most popular oil filters from well-known brands, we divided them into two categories - undoubtedly recommended or optimal for replacement if there are no other options for purchase.

Unfortunately, only imported parts will take part in the test: although a number of Russian companies produce analogues (for example, Nevsky Filter), they are not widespread, and it is hardly worth recommending a product that is difficult to buy.

The Mahle brand offers a huge selection of components for engines, from cylinder-piston units to consumables for maintenance. Mahle is one of the main suppliers of automotive production, and in this case there is no point in repeating the high quality of products once again.

The oil filter we are considering rightfully takes first place in the ranking of the best: a high-quality, thick-walled housing not only withstands pressure in the oil system during a cold start without deformation, but also unscrews conveniently: when using disc pullers, the edges on thin-walled filters often roll off, and you have to use “ the old-fashioned method with chain pullers and other, even less convenient methods. The bypass valve is calibrated for a pressure difference of 1 bar - with synthetic oil of the recommended viscosity for the Kia Rio, it will be securely closed, protecting the engine from the penetration of unclean oil. Fans of cheap semi-synthetic oils should be careful in winter - trying to drive with a cold engine will not be the best choice.

• Prevalence.
• Exact fit of the seat to the car.
• High quality workmanship.

• Not detected.

The second indisputably recommended oil filter also has German roots, although the production of Bosch products has long been distributed throughout the world - for example, our “experimental” one comes from South Africa. In terms of area, it can be considered the leader in the test: a solid cartridge made of evenly laid corrugated paper occupies almost the entire 80 mm body. This did not affect the performance of the bypass valve - it is recessed inside the filter element, has a decent area and opens exactly at 1 bar of pressure difference.

The only thing I can find fault with is the anti-drainage valve - it works noticeably hard, although the manufacturer indicates an opening pressure of 0.12 bar, but it still has more resistance than Mahle. For a healthy engine this will not be a problem, but since the softer valve on the Mahle also effectively prevents the outflow of oil from the filter, this coarsening will still not benefit the overall rating score. The oil filter for the Kia Rio, manufactured by Bosch, takes a solid second place in the Price Expert's list of recommendations.

• High quality filtration, long resource.
• Exact compliance with the manufacturer's requirements.

• Less balanced design than Mahle.

The MANN company is no less well-known supplier of consumables for automobile plant conveyors than Mahle. However, in our case, they failed to surpass their colleagues: this oil filter has a smaller height and, accordingly, filter element area than the Mahle OC205, therefore, it will be the best choice only for relatively little worn engines, into which synthetic oil with low and stable viscosity. In this case, faster clogging during the run between oil changes will not play a significant role, but the reduced height will make installation easier in a tight engine compartment.

When replacement is required

In order to change consumable components on time, it is necessary to take into account the recommendations of the vehicle manufacturer. They always provide for certain regulations for the performance of each maintenance-related work. According to the regulations for the Lada Grant, the filter element and lubricant in the system are replaced every 15 thousand kilometers.

During daily operation, the driver is required to monitor the lubricant level in the engine. The check is carried out before the start of the trip, but it is enough to do it once every few days. If the engine has just been running, it should be allowed to stand for a few minutes so that the lubricant can drain into the crankcase. Now the driver takes out the dipstick and wipes it with an unnecessary rag. The probe is inserted into its hole until it stops, and then removed again. The oil film level should be between the minimum and maximum marks on the dipstick.

The main sign that indicates that the engine lubricant needs to be changed is its color. A very black liquid no longer has the characteristics necessary for optimal operation of the power unit. Lada Granta is not as demanding on the frequency of replacement as foreign-made cars, and allows you to change the lubricant after 15,000 km. Along with it, a new oil filter is installed. However, even if the car has not covered the required mileage, it is better to perform this procedure before the onset of winter.

Oil aging leads to a decrease in its performance. Oxidation processes begin and useful additives are gradually washed out. Over time, dirt begins to accumulate in it. The purpose of motor oil is to lubricate the rubbing parts of the engine. In addition, it cools it and rinses it, removing various impurities.

Reviews

Mikhail Medved, Moscow, 25 years old: The oil filter is the most important consumable that cannot be skimped on. That's why I buy only expensive analogues and the motor works great for me.

Andrey Tashkovsky, Tomsk, 29 years old: I’ll take the original. I believe that there is no need to deviate from the manufacturer’s recommendations.

Dmitry Podkorytov, Tyumen, 27 years old: I change the oil more often. I don’t worry about the filter, I use what’s available in the store.

Preparing to change engine oil

A prerequisite is to warm up the car - the result from the replacement will be better. We find an inspection hole or overpass, prepare replacement oil and a new filter.

What you will need for work:

1. New oil;
2. Container for draining waste (at least 4 liters);
3. Hexagon 12 for unscrewing the drain plug;
4. Oil filter puller;
5. New filter;
6. If you plan to replace with flushing, use a canister of flushing oil.

Working with a lift will give full access to the drain neck and filter from below.

How to change oil on an 8 valve Grant

So, the engine is warmed up to operating temperature, the car is in the pit, the tools are at hand. How to change oil without flushing:

• Open the hood, remove the oil filler cap;
• We climb under the car: if the crankcase is covered with protection or a factory metal sheet, we dismantle it;
• we find the drain neck on the engine, place an empty container under it;
• Using a 12mm hexagon (or a 17mm wrench - depending on the type of plug) we begin to unscrew the drain plug. Please note that hot waste will flow from underneath it - at the end, sharply move your hand with the plug to the side so that it does not flood;
• After removing the plug, leave the car for 5-10 minutes so that everything is glassed;

If the car does not “eat” oil and there are no obvious leaks on the internal combustion engine, about 3 liters should drain.

We climb under the car again:

• Use a puller to unscrew the oil filter. Keep in mind that it will also leak! Not much, but it will be;
• Fill the new filter halfway with oil and wipe it around the perimeter of the seal;

Rubbing the ring will help it fit more tightly to the attachment point.

Preparing the installation site:

• We clean the place where the filter is attached from dirt, sealant residues, etc.;
• We install it in place. As soon as it starts to spin with force, tighten it three-quarters of a turn.

When tightening the filter there is a danger of overtightening. This may cause the edge to crack and oil to leak out.

• tighten the drain cap! Otherwise, new oil will drain from the engine.
• Fill with -3.2 liters;
• We close the filler neck, wait a few minutes and check the level on the dipstick - ideally the mark will be between MIN and MAX.
• According to the manual, the Granta with manual transmission includes 3.2 liters; Automatic transmission - 4.4 liters.

The oil level should be read around the indicated mark.

The last thing is to start the car. The oil pressure indicator may come on for a few seconds after starting the engine.

If it goes out, everything is fine. If not, turn off the car and check the level.

Don’t forget to check that the sensor is working - when you turn on the ignition, its indication on the panel lights up and immediately goes out.

Features of changing the oil on Lada 16 cl.

The whole process is identical to the one described above.

The only difference is that you can remove the filter on a 16-valve engine only from below after dismantling the factory (or additional) crankcase protection - if it does not have a window for such work.

Replacing the VAZ 2190 oil filter

AvtoVAZ and common sense advise changing the filter element with every oil change. To independently search and order this part online, use the following articles:

Oil filter article for Granta

21050101200500 21080101200500

21080101200508

21080101200509

How to choose a filter

One of the most popular brands of filters for Lada is Mann. Accordingly, fakes are often found. Let's look at the features of the original part.

The reputation of a reliable brand has led to frequent counterfeits of Mann parts.

The original differs as follows:

1. Laser marking of the part number on the body is dotted, barely visible in the light;
2. The body is blue – matte – NOT glossy;
3. Has stickers on the body and packaging indicating PCT compliance;
4. Made in Germany - no Germany or anything else - there must be the inscription MadeinGermany;
5. The O-ring has three yellow stripes.

You can protect yourself from counterfeit products by purchasing a filter from authorized dealers. They take only original spare parts for service stations.

Replacement with flushing

Sometimes replacement with flushing is required - using flushing oil. Most often this is required when switching from one type to another. For example, we poured semi-synthetic, but decided to pour synthetic.

For washing:

• After draining the waste, screw in the drain plug;
• We don’t remove the oil filter, it’s still old;
• fill the rinse in the required volume;
• close the filler cap and start the car;
• we drive the car out of the garage and leave it running for 10 minutes - DO NOT leave the car running in the garage - this is dangerous;
• we drive it back, turn it off;
• unscrew the drain plug and drain all the flushing;
• further - from the moment of filter replacement - as described above.

The rinse contains special cleaning additives. It cannot be used on an ongoing basis - it is designed for short-term use.

Top 5. MANN W914/2

55 reviews from resources taken into account: Yandex.Market

The best choice of the buyer Affordable price, excellent oil pumpability and consistent “German” quality have made the MANN W914/2 filter system the most popular among Lada Granta owners.

• Specifications Price: 320 rub.

According to reviews from owners of the 16-valve Lada Granta, MANN W914/2 is one of the best filters for this car. Pressure appears in the oil system almost immediately, and for an engine with two camshafts this means a lot. The quality of original products has been stable for decades. For this reason, many Granta users have no doubt which oil filter to choose: from time to time they take the “Mann” one and don’t worry about anything. The only thing that can overshadow the experience of using this product is encountering a fake.

Advantages and disadvantages

• Objective value
• Stable product quality
• Immediately provides system pressure

• There are fakes

• 10 Best Tips for Choosing a DVR

Replacing the oil filter on Grant

To ensure the job is done correctly, the replacement should be carried out in a well-equipped garage. Before installing a new Lada Granta oil filter, it is necessary to drain the used oil and remove the old consumable. Preparation will take a minimum of time, but requires increased accuracy. Replacement is carried out according to the following scheme:

1. Loosen the drain plug.

2. Place a container to drain the waste substance and open the oil filter for the Lada Granta to remove the oil.

3. After draining the oil, close the hole.

4. The old Lada Granta oil filter is removed from the mating plane from the previously loosened mounting.

5. Use a rag to wipe off any remaining substances, and wipe the rubber gasket of the new filter with clean oil.

6. Now the new Grant oil filter is installed in place and screwed until it stops.

7. The neck is opened and new oil is poured in.

8. The neck cover is installed in its original place and after starting the car, the presence of leaks is checked.

Testing against leakage is important. The new oil filter on Grant must not only adhere to the surface, but also ensure sealing of the oil. Otherwise, you will need to press the element until it snaps into place. Correct installation will save the car from engine overheating.

A high-quality oil filter for Granta will avoid numerous problems with the operation of the power unit. You can carry out the replacement yourself if you have enough experience. If the work is being done for the first time, it is better to contact service station professionals. Our specialists will carry out the replacement quickly and correctly.

Snapshot

Splash guards of the engine compartment and elements of their fastening (view from below the car): 1 - three screws with a key “8” for fastening the middle shield to the right shield; 2 — right shield; 3 - middle shield; 4 — four self-tapping screws “8” for fastening the middle shield to the lower cross member of the radiator frame; 5 — two self-tapping screws “8” for fastening the middle shield to the left shield; 6 — left shield; 7 - two 10mm key bolts securing the middle shield to the body side members.

How to unscrew it if it's stuck?

I’ll tell you a few ways that will 100% help you unscrew this element, so here we go:

Trite with your hands. Often you just don’t have enough strength, just call a “more powerful” person and everything can work out. I will say this in 80% of cases they unscrew it by hand. YES, and you need to tighten it again with your hands, tightly! IT'S ENOUGH!

Special key. I already wrote about it once, you can, of course, it’s not always at hand, but if you have a friend with a car, he can drive to almost any spare parts store and buy it. I personally even saw it in several supermarkets, the cost is a penny, about 200 - 300 rubles. Everything with it is quite easy and simple, we hook it on and unscrew it, of course, the body of the element will get wrinkled, but actually we don’t need it anymore.

Rope and screwdriver (another lever). Sometimes they also use an old alternator or timing belt. What we do is twist a loop around the filter, tighten it with a screwdriver, tightly. And we try to unscrew it. The main thing is that the rope or belt does not slip.

A hammer and a long, strong screwdriver. Actually, this method is used to unscrew most intractable filter elements. Since the walls of the element are soft, they are usually aluminum, or tin, and other soft metals. It breaks through very easily (just like a tin can). What we do is drive a long and strong screwdriver all the way through, that is, so that it goes in on one side and comes out on the other. And then we unscrew it like a lever. The most important thing is that everything can be done without a special key, and actually using the tools that are always in the garage. The only downside is that your hands are dirty, because some of the oil is always inside.

Hammer and chisel. This is generally the method that they say “ATAS”, there is nothing to explain here, we take a chisel and “fuck” it with a hammer, the most important thing is to hit closer to the bottom, to the place of fastening, and counterclockwise. The case, of course, will be all dented, but the most important thing is to unscrew it. The downside here is not only that you can get dirty, but also that you can hit the engine block with a chisel. I personally recommend the method with a screwdriver, it is still less dangerous.

As you can see, there is nothing complicated, you can do without a special key, just pierce the housing with a screwdriver.

The main purpose of an oil purification filter is to remove foreign particles and impurities from engine oil. Oil filters can vary in mounting, size, and opening pressure of the bypass valve.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! The Lada Granta is equipped with a VAZ engine from the modern 8 and 16 valve range

That is why the recommendations for installing an oil filter for the Lada Granta will be the same as, for example, for the Niva, Kalina or Priora

The Lada Granta is equipped with a VAZ engine from the modern 8 and 16 valve range. That is why the recommendations for installing an oil filter for the Lada Granta will be the same as, for example, for the Niva, Kalina or Priora.

It is recommended that the oil filter be replaced along with engine lubricant, as indicated in the regulations. This should be done every ten to fifteen thousand kilometers. The service life of the MF is reduced if you frequently use the vehicle and have an aggressive driving style: any increased loads will negatively affect the performance characteristics of the filter.

Original

Most car owners prefer to install only original components on their car, which were originally on the car when purchased. The following original oil filters are suitable for installation:

• 21080-1012005-08;
• 21050-1012005-00;
• 21080-1012005-09;
• 21080-1012005-00.

All of them are considered original and are installed on VAZ cars. Specifically, the Lada Granta is equipped with an oil purification filter, produced and sold under article number 21080101200508.

Do not forget that original components (even for Russian cars) are often counterfeited, so during the selection process it is important not to buy a fake. The quality of counterfeits leaves much to be desired; they will not be able to provide complete fuel purification and will quickly fail.

Carefully check the information on the box with pictures from the Internet. The color, dimensions, and shape of the packaging must correspond to the catalog images. Check that the packaging is free of defects, torn parts, and that the product itself is free of chips, cracks or paint runs. Most often, fake parts are painted sloppily.

Analogs

If you don’t want to overpay for a brand, then take a closer look at inexpensive analogues. They are not inferior to the original in terms of characteristics and perform all functions at the same high level. For example, the following brands are popular among car owners:

Remember to carefully check the components you purchase. To avoid counterfeiting, contact only trusted sellers. Also, do not forget to check the appearance of the packaging and the product itself.

Check if there are any extraneous inscriptions or external defects on them. If you doubt the seller’s honesty, be sure to ask for certificates for the products sold and read them carefully.

Standards and factors

How much lubricant will be used depends on its quality, viscosity, operating conditions and driving style. On average, according to the manufacturer’s documentation, the consumption per 1000 km for the Grant will be as follows:

• 8 valves, engine capacity 1.6 l, power 87 hp: consumes 50 g;
• 16 valves, motor models of all varieties: consumption 300 g.

Engine oil can be consumed more intensively - a whole list of factors affects:

1. Overflow of lubricant;
2. Clogged or faulty filter;
3. Oil viscosity. The seasonal variety is used up faster than the all-season variety. But the last one is more likely
4. loses viscosity;
5. Malfunction or high degree of wear of engine components: pistons, cylinders, pumps;
6. In a new or overhauled engine, the increased oil consumption is explained by the grinding of the elements. When it ends, consumption should return to normal.

In some cases, the reason for high expenses may be difficult to determine. But eliminating the problem is an urgent and extremely important task. Delaying it usually ends in the need for expensive and major repairs.

Top 1. BIG Filter GB-102M

6 reviews taken into account from resources: Reviewer

The best price The domestic BIG GB oil filter costs 60% less than the most popular filter element among Grant owners from MANN.

Despite the budget cost, the domestic filter element is in demand not only in Russia. The brand's products are successfully exported to neighboring countries and European countries, where quality requirements are the highest. Most often, the GB-102M oil filter is installed on the 8-valve Lada Granta. When using a more fluid lubricant 5w-40 or 5w-30, pressure in the system does not appear with the first stroke of the pump. This happens due to the increased filter capacity. Also, some owners have complaints related to the purchase of counterfeit products.