Replacing the front struts of a VAZ 2114 with your own hands - useful tips

Print this article Font size 16

Racks play a significant role in the comfort and safety of driving a VAZ 2114, as well as on any other car. Then their selection, replacement and current condition should be treated with increased attention.

When the old elements are no longer able to properly perform their duties, they have to be replaced. And here the main question arises - which racks are best to install on a VAZ 2114. We cannot give you a definite answer, since the choice largely depends on the individual preferences of each individual car owner. Therefore, we will consider all types and popular manufacturers.

Signs of malfunction of VAZ 2114/2115 racks

The following signs indicate the need to replace the struts on the VAZ 2114/2115:

1. When a strut fails, the first thing to start leaking is the shock absorber.
2. Steering wheel wobble appears.
3. Vehicle vibration increases when driving on poor-quality road surfaces.
4. The car begins to drive around.
5. The skidding trajectory on a winding road becomes larger.
6. The braking distance of a car changes upward.
7. The suspension periodically makes extraneous sounds and squeaks.

The spring that stands on the telescopic stand should not have cracks.
If this is noticed, then the strut needs to be removed and the spring replaced. When replacing one strut on a car, it is better to replace the other as well. Over time, they wear out evenly, and the different stiffness of the struts (the right side is soft, and the left side is hard) do not handle impacts equally, which contributes to a rapid failure.

How to check the struts of a VAZ 2114, VAZ 2115

Self-diagnosis methods are, to put it mildly, ineffective, so it is recommended to carry out diagnostic work exclusively on specialized equipment. There is one way, but it only works when the rack has already worn out. You will need to stand near the corner of the car (near the right pillar, for example).

Stand near the edge of the right headlight and place your hands on the hood or fender, then rock the car two or three times, and when it is at the bottom, sharply remove your hands. If the car then goes up and a little down and immediately stops without unnecessary vibrations, then the strut is most likely normal. We carry out similar actions on the left wing. Most often, one rack fails, so the difference in its “behavior” is obvious.

Another reason for the malfunction of the front shock absorber strut of the VAZ 2114/2115 is the failure of the upper support. The reason for replacing the upper supports is usually one of two reasons:

• ruptures and cracks in the rubber part of the support. As a rule, this occurs due to aging of the rubber. This is fraught with the fact that a support that is in this state will suppress noise and shocks while the car is moving much worse;
• failure of the upper support bearing. It occurs much more often than the breakage of a rubber element, and more anxiety is added, since the support with a broken bearing knocks loudly, even on small irregularities.

Checking the car on a vibration stand

For the reason that it is not always possible to identify a malfunction on your own or without removing the element, you can contact the service. Here, trained craftsmen will perform it with high professionalism.

How are shock absorber struts checked without removing them from the vehicle?

To do this, you should drive the car onto a special vibration stand. The price of this diagnostic is a thousand or more rubles. This service is also good because not only the strut/shock absorber, but also other elements of the chassis and the brake system are subject to professional inspection. On the vibration stand, road irregularities are simulated, which will allow you to correctly determine the breakdown of a specific mechanism. In addition, this makes it possible to determine the serviceability of bearings (ball and wheel) by checking the lateral rolling of the machine.

The stand has a huge number of sensors that transmit information every second to the main computer.

Vibration test

Advantages of testing with a vibration stand

• the highest accuracy in identifying the slightest faults;
• minimum amount of time.

In addition, owners of freight transport cannot do without this service. Because it is impossible to rock a large car. On a vibration stand it will be possible to establish the problem in its entirety. The only downside is the low prevalence of auto repair shops with similar equipment, even in big cities. In addition, the cost of the service for some car owners can be quite high.

So, we have given several ways to check shock absorbers for malfunctions; you just have to choose the most relevant one for you.

How to change the front struts of a VAZ 2114, VAZ 2115

There are two options for dismantling the shock absorber strut: one allows you to avoid subsequent adjustment of the steering wheel alignment angles, the second allows you to quickly complete the work with more compact units, but after that it is necessary to adjust the steering wheel alignment angles. The difference is that in the first version we remove the strut together with the steering knuckle, without loosening the nuts of the lower and upper (adjusting) bolts securing the strut to the steering knuckle. In this case, the amount of work is greater: we additionally disconnect the brake caliper and ball joint.

In the second option, pay attention! Immediately after replacing the struts, the vehicle requires mandatory wheel alignment adjustment.

We proceed according to the first option, disconnect the steering rod, remove the brake pad guide with the caliper and the brake disc, and remove the outer CV joint from the hub.

Troubleshooting

Deformation of the suspension elements, especially body braces, disorganizes the wheel angles and makes it impossible to adjust the camber and toe. First of all, you should check the car's silent blocks, rubber cushions, ball joints, and the shrinkage of telescopic struts.

Repairing a VAZ-2109 requires replacing rubber cushions and silent blocks if there is rupture and one-sided swelling, including after trimming the end surfaces of rubber elements.

You can check the condition of the front suspension ball joint on the car after removing the wheel, by measuring the distance between the lower arm and the disc element of the brake system. If, after pumping the unit, the distance increases from 0.8 mm or more, the hinge should be replaced.

Replacing front struts on a VAZ 2114

Racks play a significant role in the comfort and safety of driving a VAZ 2114, as well as on any other car. Then their selection, replacement and current condition should be treated with increased attention.

When the old elements are no longer able to properly perform their duties, they have to be replaced. And here the main question arises - which racks are best to install on a VAZ 2114. We cannot give you a definite answer, since the choice largely depends on the individual preferences of each individual car owner. Therefore, we will consider all types and popular manufacturers.

A couple of practical recommendations for diagnosing shock absorbers on a vibration stand

Testing at a stand naturally costs some money. Your money. Therefore, before you drive your car to the stand, find out for yourself:

• The stand's computer can be adjusted to the model of your car or a similar suspension.
• How is the life expectancy of a car calculated? Over time, the rigidity of the body changes, so a 10-year-old car will in no way meet factory depreciation standards. And the stand will show it.
• Before checking, it is necessary to check the wheel alignment and tire pressure.

Diagnostics of shock absorbers is not an easy task, but it is worth it, since it turns out that a lot depends on a working shock absorber. First of all, the serviceability of the car and traffic safety.

Results of the influence of a shock absorber on car performance

Braking distance at a speed of 100 km/h: before replacement 51.5 m, after – 47.5 m.

The maximum speed for passing the “reference” turn before the replacement is 84 km/h, after it is 105 km/h.

So draw your conclusions. Good luck, car lovers.

Kinds

There are three types of A-pillars that are suitable for installation on the VAZ 2114.

1. Oil comfortable. If you like a quiet, measured ride, choose oil ones. They are installed on Samara 2 from the factory. They smooth out bumps on the roads well, but at high speeds they behave unstably and the car can sway violently.
2. Gas-oil. An average solution that will allow you to ride comfortably at low speeds, but at the same time enjoy a sporty driving style if necessary. The best option for the average driver.
3. Gas. If you love tuning and huge speeds, then your choice is exclusively gas struts. But get ready for the fact that every bump and unevenness will be felt under you. In urban conditions, such spare parts will not last long. These are rather track solutions for the corresponding tuned versions of the “fourteenth” model. By installing short-travel struts on a VAZ 2114, you can achieve better aerodynamics and downforce by lowering the suspension. Short strokers are a device with limited rebound travel, in short.

What are the consequences of a faulty shock absorber?

Shock absorbers (dampers) are devices that serve to dampen vibrations while a car is moving (damping) by converting mechanical energy into thermal energy. Shock absorbers operate in conjunction with such vehicle suspension elements as springs, springs, torsion shafts, cushions, etc.

Diagnostics of shock absorbers must be carried out systematically by the driver. Why, you ask, because MOT was passed, and everything was fine. Unfortunately, like everything in this world, shock absorbers tend to fail. And the sooner the driver notices a shock absorber malfunction, the less money will then be spent on restoring the consequences.

The most important thing is for you to remember that systematically checking the shock absorbers yourself takes a couple of minutes, and can save you from troubles with other car systems.

• A faulty shock absorber in combination with a wheel imbalance (you understand that perfect balance simply cannot exist) leads to intense and rapid tire wear. Add here broken wheel bearings, check the cost of tires and bearings - your budget will not like the figure.
• A faulty shock absorber causes other suspension parts to fail. After all, the suspension is designed to work with all the elements together. For example, after several thousand km. The support bearing of the strut may fail.
• The health of the shock absorber directly affects the service life of the brake system, in particular brake discs and pads. If you are not interested in repairing brake discs, then timely diagnostics of shock absorbers will help postpone this procedure.
• A faulty shock absorber increases the braking distance, which means a few extra meters can lead to an accident. And here you can’t count, you can’t count – your body repairs and... you don’t even need to think about it. And you just need to check the shock absorbers in time.

Leading manufacturers

When choosing new nodes, you should think about what exactly you want to get and what it will be like for you in the future. We recommend installing collapsible struts, since their design can be disassembled into parts, thereby simplifying and reducing the cost of suspension repairs. This is one of the key advantages of collapsible units.

KYB (Kayaba)

Look at the front element assembly in the photo to first understand what exactly this component of your car looks like. Choosing a manufacturer is a fairly pressing issue, since each of the options presented today has its own advantages and disadvantages. We invite you to familiarize yourself with them in the table.

From this we can conclude that spare parts from Kayaba are the optimal solution that will last a long time, reliably, and will not be afraid of harsh Russian winters, during which many analogues among the A-pillars simply will not be able to function normally, causing problems for you.

Selection of new

Look at different photos to see what the assembled rear pillar for a VAZ 2114 looks like. This will allow you to understand what you generally need to look for for this car.

Kayaba kit

We will not rant about which ones to buy, with what characteristics, from what materials, and so on. We will simply offer you objectively the three best options.

Signs of breakdown

It is often stated that the front struts on a VAZ 2114 can last about 60 thousand kilometers. In fact, the figure is not entirely fair, since under the conditions of our roads it is significantly reduced. Sometimes even twice.

Therefore, the car owner’s task is to monitor the condition of the suspension and front struts in particular, identify signs of breakdown in time and replace the units.

Worn out

If your racks are really reaching the end of their service life, you can determine this by the following signs:

• The car behaves unstably on the road;
• When driving over obstacles, the car sways strongly;
• When entering turns and braking, the car is unstable;
• The braking distance increases noticeably;
• There are traces of oil on the body;
• There is a noise or knocking noise from the front of the car.

Some, even with such obvious signs of malfunction, continue to ignore the car’s need to replace the front struts. If you do not take any action, the consequences may be as follows:

• The car will bounce on every bump;
• Controllability in corners will decrease significantly, the car will pull to the side and turn around;
• Tires will lose their quality and wear out in the shortest possible time;
• Soon you will have to go to the wheel alignment.

If the replacement of the front struts on the VAZ 2114 is carried out in a timely manner, these problems and huge financial costs can be avoided.

Why did it happen so?

Perhaps the automatic requests do not belong to you, but to another user accessing the network from the same IP address as you. You need to enter the characters into the form once, after which we will remember you and be able to distinguish you from other users exiting from this IP. In this case, the page with the captcha will not bother you for quite a long time.

You may have add-ons installed in your browser that can make automatic search requests. In this case, we recommend that you disable them.

It is also possible that your computer is infected with a virus program that is using it to collect information. Maybe you should check your system for viruses.

If you have any problems or would like our support team, please use the feedback form.

Hello. The quality of Russian roads cannot be compared with the roads of European countries. Especially in the spring, when the snow melts, a bunch of new holes appear, falling into which the suspension suffers

The racks receive the most energy from impacts, so it is important to monitor their condition. Otherwise, impacts will be transmitted directly to the body

This article explains how to check the rear struts on VAZ cars and how to replace them.

Replacement

Before you get started, we recommend watching a video on how to make the replacement. This is a useful lesson that will provide the necessary knowledge and concepts about the location of certain components of the unit.

Removed suspension element

But let’s say right away that the lack of at least basic experience in car repair means that you should not start replenishing your own knowledge base with such a process as replacing these parts. It is better to entrust this issue to specialists.

If you decide to do everything yourself, then follow the specified algorithm. This will allow the replacement to be completed efficiently and without unnecessary manipulation.

1. Place the car on a flat area, preferably with a hole. Loosen the bolts on the front wheels. Be sure to turn on the handbrake and secure the wheels with chocks. You need to think about safety first.
2. Use a jack to lift the front of the car, then remove the wheel. Please note, when changing the front suspension elements, it is better to do this on two wheels at once, even if one of the struts is in satisfactory condition.
3. Lift the hood and look for the bolts that secure the struts to the body. Look for them on the left and right, near the windshield.
4. There is a plastic cap on the glass that needs to be removed. To do this, use a simple flathead screwdriver. The plastic element is pryed off and thus easily removed.
5. Unscrew the mounting nuts holding the rack on top of the body.
6. A brake hose with a bracket is attached to the rack. This element is also removable.
7. Using a wire brush, be sure to clean all the fastening elements of the struts to the body and chassis of the car.
8. Now take the pliers in your hands and use them to unscrew the nut. The one that holds the tie rod end joint to the A-pillar.
9. A puller removes the hinge from the shock-absorbing strut arm. If this is your first time changing them and no one has removed them before, be sure to tighten the nut a few turns, which will protect the threads.
10. Near the place where the fist is attached to the stand, there are nuts that should be removed. Just first mark where the adjusting bolts are located. This way you won’t have to go to a wheel alignment after replacing suspension elements.
11. Using a hammer, knock out the bolts that hold the element and the fist. The nodes release, allowing you to pull your fist down and reach the worn post.
12. Place the new part, then proceed to reassemble the unit in the reverse order. During the procedure, do not forget to check other components for defects, malfunctions, oil leaks, and so on.

When the procedure is completed, put on the wheels, but do not tighten the bolts tightly. By lowering the car from the jack, you can fully secure the bolts. This is an important rule that, unfortunately, many people forget about.

Replacing the front struts is not the most difficult procedure, but it requires observance of a sequence of actions, accuracy and regularity.

VAZ 2114: replacing the front pillar with your own hands

On a VAZ 2114 car, the front strut is replaced if it fails. The resource of the suspension element is quite long, but do not forget that the fourteenth has been produced since 2001, and the youngest car is currently three years old. And the service life of a shock absorber depends on many factors, including the conditions in which the car is operated. And, unfortunately, they are not always ideal - the quality of the roads leaves much to be desired. Let's look at the entire process of replacing the front pillar on a VAZ 2114.

Analogs

If you want to save money, purchase similar parts. They are not inferior to factory ones in quality, and in some cases even surpass them. The most popular options for replacing front struts:

It's no secret that even products from little-known brands can be counterfeited. Safety measures remain the same: ask for documentation, inspect the box and the part itself, and make sure that there are no external defects. Check if all the inscriptions are printed on the box. This way you will protect yourself from low-quality components.

Non-working, failed rear struts can be replaced with:

Shock absorber struts can only be replaced in pairs. The reason is that with different sagging of the struts, the wear of the replaced part increases. Tires also suffer from increased wear, because the sides are not balanced. Wheels positioned at the wrong angle reduce the maneuverability and controllability of the vehicle.

Tools for work and materials

When replacing the front strut on a VAZ 2114, it is necessary to have all the following tools at hand:

1. Jack (ideally, of course, a hydraulic or pneumatic one would be suitable, since they are convenient to work with).
2. A set of keys.
3. Pliers, duckbills, forceps.
4. Hammer and chisel (just in case).
5. Puller for the ball joint of the steering tip.
6. Spring tensioner.
7. Steel wire.
8. Lubricant like WD-40.

Replacing the front struts of a VAZ 2114 with your own hands is impossible without a new set of spare parts. What is better - to take all the elements separately or together? Depends on how “killed” the shock absorbers installed on the car are. If all the elements of the rack have become unusable, then you can purchase it assembled, then the repair procedure becomes much easier - it will be enough to unscrew a few bolts and install all the suspension components.

But this is true for cases when you purchase branded spare parts, for example, Kayaba (KYB, Kayaba). But if the renovation is “budget”, then you can collect all the elements separately:

1. Shock absorber strut VAZ 2114. Standard SS20.10P/L.00.000-01 will cost you about 5,000 rubles, but you can find it cheaper. The price directly depends on the manufacturer. But we must not forget that quality can also be judged by price. On the VAZ 2114, the front strut is not replaced so often, so you need to be responsible when choosing components.
2. Support bearing number 348702 (or included 8115). Bearing dimensions 14.5x52x1475x100x19 (according to specification).
3. Chipper (silicone is preferable, but rubber is also possible). The ideal copy is number SS74101 - a complete analogue of the stock one.
4. Anther. The cheapest option is plastic, with the number 2108-2902814, but it deteriorates quite quickly and is not worth buying. The similar 2110-2905681-R, from the front pillars of a VAZ 2110, performs much better in operation.
5. Bolts securing the hub to the shock absorber.
6. A spring is needed if the old one has sagged too much.
7. “Little things” such as washers and metal spacers for springs can be borrowed from an old rack.

But we must not forget that the replacement must be carried out simultaneously on both sides! Therefore, all of the above spare parts will have to be purchased in double quantities.

Bleeding shock absorbers:

None

Full size This is how I saw this support. Naturally I decided to replace it))) And of course with my own hands))) And so we proceed to the replacement.

The first thing we do is loosen the hub nut. This is best done at the very beginning without lifting the car. We take a 32 head (I still have this head from the Opel days - there is the same nut on the hub) and put an extension pipe on the key (the nut is clamped very tightly):

None

None By the way, I forgot the most important thing))) When making repairs, it is advisable to have:

None

None

Full size It’s easier to unscrew with a ratchet) Luckily there is a good tool))) Then we take pullers

Full size With red handle still from Opel)

And remove the steering tip:

Full size Steering end removed

We do the same with the ball:

Full size Unscrew the nut and snap it off with a puller

Then we unscrew the three nuts on top of the support itself and remove the stand assembly: Then we compress the spring with zip ties and unscrew the top nut:

Full sizeThis is how we compress the spring

We take new supports. I took these:

None

None Issue price: 1,150 ₽.

The front struts on VAZ 2114-2115 cars wear out much faster than the rear ones, and this is due to the fact that the front part of the car bears a large load, since the main units are located there. If the shock absorbers are leaking, or are starting to leak heavily in potholes, then it would be best to completely replace them. Many people are used to dealing with such problems at a service station, although if you try a little, you can do it all on your own.

The main thing is to have all the necessary tools and equipment at hand. Below is a detailed list of everything:

• spring ties
• ball joint or steering wheel remover
• pliers
• hammer
• keys for 13 and 19 as well as similar heads
• crank and ratchet handle
• breakdown

I recommend that you first familiarize yourself with the video, which will be presented below, and then read my photo report on the work done.

Replacing the front struts of a VAZ 2114

And now more about how to replace the front strut supports of a VAZ 2114 with your own hands. First, you should prepare the car for work - disconnect the battery, install stops under the rear wheels so that the car cannot be moved. And we begin:

1. Raise the side to be repaired using a jack.
2. We remove the wheel. Need I say that you need to loosen the bolts in advance?

1. Place the brake pipe to the side so as not to damage it.
2. Using keys “17” and “19”, unscrew the bolts securing the strut to the hub. These bolts and nuts can be thrown away immediately - reuse is unacceptable. Firstly, there is a plastic lock on the thread, and it is designed for a small number of tightenings. Secondly, metal fatigue affects and the bolt can become deformed when tightened.
3. On a VAZ 2114, the front strut can be replaced without removing the spring. But you still have to unscrew the nut and remove the tie rod end.
4. Using a key set to “13” you need to unscrew all three nuts that secure the support bearing housing to the car body.

After this, the entire rack assembly can be removed and a new one installed in its place. As you can see, replacing the front struts of a VAZ 2114 is not that difficult. But if you install an old spring, you will have to tinker with disassembling the old unit - this can be problematic, since long-term use takes its toll on it. Rust appears, the metal “sticks”, sometimes even penetrating lubricant cannot help.

The repair procedure is the same on both sides. Installation of a new rack is carried out in the reverse order. It is important to observe the tightening torque of threaded connections, since your safety depends on it. Use a torque wrench for convenience. At this point, the replacement of the front struts of the VAZ 2114 is completed, you can continue to use the car.

Shock absorber: its role in suspension operation

An automobile shock absorber is a mechanism in the suspension of a car that serves to partially dampen the swaying (damping) that occurs during movement or completely absorb it.

Shock absorbers are divided according to their types:

• gas single-pipe;
• gas two-pipe;
• oil two-pipe.

On the VAZ-2115 model, standard oil shock absorbers are installed at the factory. Later, when using the car, owners often replace them with gas ones, depending on their driving style.

There are 3 types of racks with different characteristics. You need to choose them based on the roads on which traffic occurs. Oil (hydraulic) – quite elastic. Designed for drivers who prefer a calm, measured ride or frequent trips on unpaved roads.

Once the shock absorber malfunction is clearly determined, it should be replaced. You can carry out the replacement either at a service station or yourself. To do this you should have the following tools:

• a wrench for unscrewing the shock absorber rod nut;
• standard jack;
• cotter pins, vices and puller;
• hammer, chisel and pliers;
• open-end and ring wrenches for 13, 17, 19, 22, 24;
• balloon wrench.

Before dismantling the VAZ-2115 rear shock absorber, you need to remove the plastic plug from the rear strut cup and unscrew the nut securing the rod. To do this, use a special key that simultaneously fixes the rod and unscrews the nut.

After removing the nut and washer with a rubber cushion, jack up the car and remove the rear wheel to gain access to the bottom of the rear strut mount.

Using a 19-mm open-end wrench, we fix the nut, and with a 19-mm socket, we unscrew the bolt, lubricating it with pre-penetrating lubricant, unscrewing and removing the bolt from the hole, and remove the rear shock absorber from its seat. To do this, it is better to use a flat-head screwdriver, carefully prying up the lower part. The strut body is moved to the side, lowered down and the shock absorber is removed.

We take out the remaining rubber gasket inside the glass with the same screwdriver. We disassemble the old shock absorber, removing the spring, rubber bushing, cup, casing, bump stop, and then install these parts in the opposite (reverse) order on the new strut.

Upon completion of complete assembly, the rear strut is installed in the reverse order, the upper nut and the lower bolt securing it are tightened.

Signs of front strut failure

As we mentioned, the front struts can “live” much less than 60 thousand kilometers. In order to avoid problems, you must first focus on the driving performance of the car and its behavior on the road.

Rack malfunctions manifest themselves as follows:

1. Reduced road stability;
2. excessive rocking of the car when hitting obstacles;
3. poor car stability during braking and cornering;
4. increased braking distance;
5. the appearance of oil drips on the body;
6. the occurrence of extraneous noise or knocking in the front of the car.

Please note that if there are obvious signs of malfunction, the front struts of the VAZ 2114 should be replaced as soon as possible. If this is not done, the following consequences are possible:

1. The car will literally bounce at the races;
2. controllability when cornering will decrease (centrifugal forces will pull the car to the side, try to turn around, or even pull it into a ditch);
3. tires wear out faster;
4. very soon you will need a wheel alignment.

At the same time, timely replacement of shock absorber struts will avoid many problems and save your own budget.

What are racks

First, let's figure out what racks are. Stabilizer struts are a technical device consisting of several components designed to dampen vibrations when driving on uneven roads. The system may be filled with oil or gas inside.

The service life of the struts is 80,000 km if they are installed during scheduled maintenance. After this they should be replaced. Some people wonder how to change the racks - in pairs or one at a time. Even if you need to replace one, it is better to change a pair at once, regardless of whether it is the rear or front struts of the car.

The main signs of malfunction of the stabilizer struts:

• oil leaks on the body;
• the car shakes violently on uneven roads;
• poor contact of tires with the road surface.

If all this is present, you need to immediately contact a car service or repair the fault yourself. You shouldn’t put off repairs until later so that you don’t have to change the entire suspension.

Replacing the front struts of a VAZ 2114, step-by-step instructions

Before you start work, stock up on the necessary tools. Here you can get by with a standard set.

Prepare two open-end wrenches (for “thirteen” and “nineteen”), a special wrench for “twenty-two”, a puller designed to remove the tie rod end, pliers and a small hammer.

Please note that you should change the racks on both sides at the same time. In this way, you will save a lot of personal time and save your nerves in the future.

Otherwise, the worn and new strut may behave differently in motion, which will lead to deterioration in the car’s handling (this will be especially noticeable on wet or slippery roads).

Replacement of racks is carried out according to the following algorithm:

1. Loosen the mounting bolts on the front wheel, apply the handbrake and secure the wheels with wheel chocks. All this is necessary to prevent any movement of the car during work.

2. Raise the front part of the car with a jack, place some supports and remove the wheel.

3. Open the hood and find the bolts securing the struts to the car body (they are located on the left and right sides closer to the windshield).

4. Remove the plastic cap that is fixed on the glass. To do this, just pry it off with something sharp (a regular screwdriver will do).

5. Unscrew the nuts that secure the rack to the car body on top.

6. The brake hose is attached to the car pillar on a bracket - remove it.

7. Take a wire brush and clean all the parts attaching the strut to the elements of the body and chassis.

8. Using pliers, loosen the nut that secures the steering linkage joint to the front strut.

9. Use a special puller and remove the hinge from the suspension strut arm (photo 1). If the racks have not been removed before, then before using the puller (to protect the thread), screw the nut 3-4 turns.

10. Unscrew the nuts located near the place where the “knuckle” is fixed to the shock absorber strut (photo 2). But before that, it would be a good idea to put special marks on the adjusting bolts before unscrewing them (this will allow you to avoid doing wheel alignment).

Note! That experts still recommend doing wheel alignment when changing struts.

11. Use a drift to knock out the bolts holding the knuckle and strut in place. Separate the nodes and move the fist down and remove the stand.

12. Install a new part.

13. Carefully reassemble everything in reverse order.

In conclusion, remember a few simple rules:

1. Carefully check all components for damage, cracks, burrs or dents;
2. Unscrew and tighten bolts only when the vehicle is firmly planted on the ground.

If everything is done correctly, then the work of replacing both racks will take no more than an hour. Good luck on the roads and of course no breakdowns.

We recommend watching a video that will help you replace the front struts on a VAZ 2114 with your own hands. In this video you will also find everything about pumping shock absorbers. Learn how to bleed shock absorbers on a VAZ 2114 yourself.

Execution Sequence

2. Using our hands, we rock the upper part of the front wheel of the car in the transverse direction. We check the front suspension on the other side of the car in the same way.

If play is felt (even barely noticeable), then we check the reliability of the steering knuckle to the front suspension strut and the condition of the hub bearing (see “Wheels, tires and hubs”).

Recommendation: It is better to check the performance of shock absorbers after a long trip, until the working fluid in the shock absorbers has cooled down.

3. Vigorously swing the front part of the car body in a vertical direction. If, due to inertia, the body continues to oscillate (more than two movements - up and down) after it has stopped rocking, then one or both shock absorbers are faulty. To identify a faulty shock absorber, we repeat the test, applying force first on one side of the car and then on the other.

Note: This test only identifies faulty shock absorbers. The effectiveness of vibration damping by shock absorbers can only be checked on a special stand.

4. Inspect the suspension struts - fluid leakage from the shock absorbers is not allowed.

Recommendation: Shock absorbers should be replaced as a pair, even if the second shock absorber on the front suspension is working.

5. Visually check the condition of the cushions (1) and struts (3) of the anti-roll bar, rubber-metal hinges of the arms and longitudinal braces (2), and covers of the ball joints (4).

. cross brace cushions (5).

We replace hinges and cushions with one-sided bulging of rubber, tears and cracks (see the relevant sections below).

6. Check the tightness of the nuts securing the suspension parts and tighten them if necessary.

7. Inspect the suspension parts. Deformation and fatigue cracks in suspension parts are not allowed. We replace damaged parts.

8. Using a caliper, measure the distance between the brake disc and the wishbone. If, when the body rocks, this distance changes by more than 0.8 mm, then replace the ball joint. Similarly, we check the ball joint of the other front suspension strut.