Tips from experts on replacing Lada Granta glass with your own hands

Rubble is the most dangerous and unpredictable enemy for a driver on the road. It is impossible to predict from which side it will bounce, especially on a large-tonnage truck. The consequences of contact of crushed stone with the glass surface are very different.

Much depends on the speed at which the “contact” occurred. Over 75 - 80 km/hour is fraught with the risk of getting a crack, the so-called rosette. At lower speeds, only a strong impact is possible. Ultimately, replacing the windshield on a Lada Granta is guaranteed.

Control points and geometric dimensions of Lada Granta

Body control points are needed for defect detection and adjustment of car body parts.
To correct the geometry of the body, special rulers and tape measures are used, using geometric dimensions, special tools and stands.

By inspecting a car after an accident, the presence of “hidden” deformations in the power elements of the body can be determined:

- by the presence of distortions in the front parts; the magnitude of protrusions of one part relative to another;

— for violations of gaps in the interfaces of openings with doors, hood, trunk lid.

Damage to the body of a passenger car usually leads to the appearance of various distortions, which manifest themselves in violation of the geometric parameters of openings (doors, hood, trunk lid), side members, and interior frame beyond the permissible limit.

Depending on the complexity of the damage, body distortions are classified into 5 types.

Opening skew includes violations of the geometric parameters of various body openings beyond the permissible size.

Various combinations of side door, windshield or rear window frame distortions are classified as this type of damage.

A slight misalignment of the body involves damage that violates the geometric parameters of the openings of the hood or trunk lid (tailgate) beyond the permissible size without violating the geometry of the base of the body, door and window openings, with the exception of gaps between doors and front or rear wings.

Body distortion of medium complexity includes simultaneous violation of the geometric parameters of the openings of the hood and trunk lid (tailgate) or damage to the body with violation of the geometric parameters of the front or rear side members beyond the permissible dimensions without violating the geometry of the interior frame.

For front-wheel drive vehicles, only the misalignment of the rear side members is taken into account.

A body distortion of increased complexity involves a simultaneous violation of the geometric parameters of the front and rear side members or damage to the body with a violation of the geometric parameters of the front and rear side members and the interior frame, or only the front side members for front-wheel drive vehicles - in excess of the permissible size.

Body distortion of particular complexity includes damage with violation of the geometric parameters of the front and rear side members and the interior frame beyond the permissible dimensions.

Elimination of body distortions is carried out by restoring damaged elements of openings, side members, and frames using straightening - stretching, shrinking and straightening until they are given their original geometric parameters.

Below are the geometric dimensions, relative to the control points, of the Lada Granta car.

Figure 2 shows the geometric dimensions of the engine compartment of the Lada Granta.

Figure 3 shows the dimensions of a car windshield.

Figure 4 shows the dimensions of the rear window of a Lada Granta car.

In Figure 5, the dimensions between the measurement points of the luggage compartment of the Lada Granta car body

In Figure 6, the geometric dimensions between the points of the lower parts of the Lada Granta car

Interior

Despite the fact that the roof is still reduced, this did not have a significant impact on the spaciousness of the cabin. The rear seats are quite comfortable even for tall people. The interior of the cabin has French features that are quite recognizable on all modern Zhiguli cars. The round deflectors on the panel are framed by a silver frame, between which there is an emergency button, and the dashboard backlight is soft green. Just below there is space for a 2-DIN device. Depending on the configuration, there may be a multimedia system, a radio tape recorder, or just a regular plastic plug. Even lower is a control unit that performs various functions. Again, depending on the design options, climate control, air conditioning, or a conventional stove are controlled through it. On the right is an impressively sized glove box; in addition, there is an always accessible compartment where it is convenient to put small items. Near the gearshift knob there are two standard cup holders. They are quite deep, so you don’t have to worry about your drink spilling on turns or uneven roads. The steering wheel is the traditional three-spoke one, although it lacks function keys. To the left of the steering wheel is a control panel for mirrors and headlights. The panel itself is made of hard plastic, with silver inserts in places. It was made without significant gaps and does not cause any special complaints. There was no foreign plastic odor noted. The seats are made of fabric, with high-quality stitching, and are adjustable within a wide range; even a tall person will be able to sit comfortably. There is nothing new; in fact, this is a complete repetition of the Granta Sedan interior. The rear window, which looks more like an embrasure, raises some questions. On the other hand, for driving backwards there are mirrors 9,8,7 which perform their function perfectly. The trunk in the liftback has an impressive volume of 440 liters, and if desired, you can expand the rear sofa and increase the size up to 760 liters, which will clearly appeal to fans of country trips. There is also a place for “docking” measuring 15 inches.

Dimensions of rear windows of Lada Granta

Depending on the body type, the length of the rear window on the Lada Granta varies from 1131 to 1178 (mm), width - from 644 to 754 (mm).

Typical dimensions of rear windows on Lada Granta:

As a rule, rear windows for the Lada Granta model are made of tempered single-layer “stalinite” 3 (mm) thick.

Glass dimensions are indicated in the “length/width” format:

Important: in most cases, the rear windows for this Lada model are equipped with electrical heating through filaments built into the glass, the power of which comes from the electronic unit.

Installation process

Before installation, you need to prepare new glass:

1. Apply a layer of primer around the perimeter and wait 10 minutes.
2. Treat with primer and let dry for 10-15 minutes.
3. Apply a layer of glue 10 mm thick and 10-12 mm high along the edge of the glass. Make sure that the sealant strip is not interrupted.
4. After 15 minutes, apply the windshield to the frame, pressing lightly so that the sealant does not come out too much over the edge.
5. Install molding.
6. Secure the part with tape.
7. Cut off the remaining sealant with a knife.

The sealant dries in 24-36 hours. It is recommended to check the glued areas for leaks after the glue has completely dried. It is necessary to close the doors and pour water onto the front bucket, then carefully look inside the cabin to see if there are any leaks. If a defect is found, wait until the part dries, bend the rubber band and re-glue the leaky joint.

It is recommended to install attachments: mirrors, rain/light sensors, heating after all checks and the sealant has completely dried.

Other parameters of Lada Granta:

The measurement is taken along the widest bottom part of the glass, on the outside.

Caution: in data after which a letter designation is indicated in brackets (for example: Upper length (AB)) indicate the size of the glass opening, in all other cases the data refers to the glass dimensions.

Common Mistake

Installing frameless brushes, especially the budget range, does not always lead to the desired results. At speeds up to 60 km/h, the windshield wipers work perfectly, up to 80 - passable. And then, if you drive along the highway faster than 90 km/h, the blades no longer adhere to the surface of the glass - they “fly up”. Although everything looks great from the outside. More details in the material: front wipers are poorly cleaned!

Frameless wipers 40 and 60 cm Frameless wipers 41 and 60 cm

Let us remember that here we were talking specifically about frameless ones. Perhaps our criticism will not be relevant for expensive solutions.

Previously, in the 2109 and 2114 families, flatter glass was used than on Kalina/Grant. On convex glass, the “right wiper” may not reach the lower corner (see photo). The problem is solved by installing frameless brushes. And what this entails was discussed above.

Right windshield wiper blade

Geometry of Lada Granta (VAZ 2190)

Body dimensions of VAZ cars, data on geometry and control points of Lada 2190 from factory documentation.

Reference linear dimensions of Lada Granta door openings

Reference linear dimensions of the openings of the wind and rear windows of the VAZ 2190

Control dimensions of the body in the engine compartment (underhood of Lada Granta)

Control dimensions of the trunk lid of the VAZ 2190

Main body dimensions of VAZ 2190 (Lada Granta) bottom

Factory diagrams show the overall dimensions of the Lada Granta body, the distance between the wheels, the angles of the front and rear overhang, the track width, the spaciousness of the cabin and some other dimensions.

The width and height of the body remained similar to the Lada Granta sedan, only the length of the body differs; in the liftback it is 14 mm shorter. The interior dimensions of the Lada Granta liftback are also almost the same as those of the sedan. The only exception is the space above the head of the rear passengers, which has decreased by 8 mm.

The trunk volume is 440 liters, but can be increased to 760 liters if the rear seatbacks are folded down.

Also, it is worth noting the difference in the size of the luggage compartment. In the sedan and sport body, the trunk has the same volume - 520 liters, but in the liftback, the trunk is increased to 760 liters, thanks to the modified body.

The width of all three types: sedan, liftback and sport is absolutely the same. The dimensions of the car, from the edge of the left mirror to the edge of the right, are 1.7 meters. These dimensions are not very different from other Lada models (in width). At the same time, roominess and comfort are completely different in each model. For example, in Grant the interior is quite spacious, which cannot be said about Kalina.

The height of the sedan and liftback bodies is the same and equals 1.5 meters. But as for the Lada Sport, its height is slightly smaller - 1470 mm. The difference of 30 mm is achieved due to the lower suspension. Dimensions indicating height are calculated from the road surface with which the wheel comes into contact to the top point of the car roof.

Also, the Granta Sport has a wider wheelbase. That is, despite the same width of all bodies, for this sample, the wheel axles are lengthened by 15 mm. Of course, such a difference is not significant, and with such dimensions, the wheel will not stick out from the arches, increasing the dimensions of the car.

The doors are quite wide, which ensures comfortable entry and exit of passengers. The height of the rear door is 97.2 cm, and the width is 61 cm at the bottom and 83.3 at the top. The front doors have slightly larger dimensions: height – 1 meter, width – 1 meter 72 millimeters. With the doors fully open, access to the interior will not be a problem.

Appearance

In May 2014, the Lada Granta Liftback model came to replace the obsolete “thirteenths” and “fourteenths”. This is the first attempt by the Tolyatti plant to produce the same model in different body styles. There is essentially no difference between the names “liftback” and “hatchback”. This is just a marketing ploy by AVTOVAZ in order to attract additional attention to the new model. And what’s typical is that they succeeded. The liftback quickly became a popular car among young people.

Tips from experts on replacing Lada Granta glass with your own hands

Rubble is the most dangerous and unpredictable enemy for a driver on the road. It is impossible to predict from which side it will bounce, especially on a large-tonnage truck. The consequences of contact of crushed stone with the glass surface are very different.

Much depends on the speed at which the “contact” occurred. Over 75 - 80 km/hour is fraught with the risk of getting a crack, the so-called rosette. At lower speeds, only a strong impact is possible. Ultimately, replacing the windshield on a Lada Granta is guaranteed.

Preparing for replacement

Preparatory work is necessary so that replacing the windshield on a Lada Granta can be done quickly, in one and a half to two hours. Step-by-step instruction:

1. Wash and dry the car.
2. Install on a flat surface, outdoors or in a ventilated garage, the air temperature is not lower than 10 degrees.
3. Remove the negative terminal from the battery.
4. Dismantle the attachments in the cabin, remove the rain sensors, heating, if any, remove the wipers.
5. Remove the wind cap.
6. Unscrew the side panels of the pillar trim. Cover the torpedo with a piece of canvas or paper.
7. Remove the seal from the top of the door.
8. Pull out the molding and rubber seal installed around the perimeter of the windshield.

If the triplex has significant chips and multiple cracks, cover the damaged area on the interior side with tape.

Required tools and materials

When replacing at a car service center, craftsmen use vacuum suction cups to dismantle and install new glass. It is not advisable to buy a tool for a single replacement, so it is better to remove the old part, try it on and install it with a partner. This will save a lot of time.

For gluing, you can take a special kit, which includes the necessary tools, or prepare it yourself; for work you will need:

• sealant;
• primer (optional);
• primer;
• metal string for cutting, you can take a guitar one;
• construction knife with a round edge;
• scotch;
• awl;
• new glass.

Cost and dimensions of front / rear windows of Lada Granta models

Removing old glass

Car dealerships always replace the seal. When making repairs yourself, you need to check the part and if there are no creases or stretch marks, then the elastic band can be reused. Dismantling old glass in stages:

1. Make a through hole in the sealant in the side of the windshield with an awl.
2. Stretch the string.
3. Tilt the string towards the glass and forcefully cut out the part around the perimeter.
4. If there is a danger of damaging the paintwork because the string is crooked, it is better to cover the frame with tape.
5. Pull out the windshield.

The most important step in self-installation is preparing the seat. The frame must be cleaned of old glue and primed. It is recommended to use assembly cutters or a construction knife. You cannot clean the seat down to the metal; it is better to leave up to 1-2 mm of the old sealant. When gluing, this will give additional grip and increase adhesion.

Third-party glass manufacturers for Lada Granta. Price category overview

*prices are current as of September 17, 2018

A list of the most popular and sought-after manufacturers is presented. At the time of purchase, the range may be expanded by new manufacturers. Beware of counterfeits, always ask for a quality certificate for the products you sell, including at official points of sale.

Post-installation recommendations

Even when replacing it at a service center, the technicians allow the car to “settle” for at least 2 hours and only then allow the vehicle to be used in a gentle manner.

1. The maximum speed for the first two days is no more than 40 km/h.
2. Avoid bad roads; Drive over potholes, potholes, and speed bumps at minimum speed.
3. You cannot brake or accelerate sharply.
4. It is not recommended to slam doors or play loud music.

After self-installation, it is not recommended to start the engine until 8 hours; you can remove the tape only after 36 hours. It is better to leave the side windows open.

What you need to know when choosing glass for the Lada Granta

Original products are always marked with a barcode that stores information about the manufacturer, date, batch number, and standardization.

Basic and mandatory details:

• manufacturer;
• standard;
• batch number;
• in-plant search index.

It is noteworthy that the date of manufacture is indicated in the form of bold black dots in combination with symbols. So, the number “2” and two dots indicate the year of manufacture 2012, the month of December.

Sequence of actions when replacing glass on a Lada Granta yourself

Windshield

Before replacing, always carry out diagnostics to identify the breakdown, defect, location. So that during the installation process “hidden” breakdowns are not discovered. The accuracy of the calculation will allow you to avoid unnecessary expenses and the purchase of “unnecessary” spare parts and components.

Tools: soil, based on 50 ml. for one windshield/rear window. For side doses, the dose is divided by half. Next, we prepare the string, which is the name of the special device for cutting the seal. You can buy it either at a car dealership or make it yourself: two screwdrivers, between which a string is stretched, a wire with a cross-section of 0.1 cm.

Algorithm

• We install the machine within the perimeter of the repair area, on a flat platform / inspection channel. There is no need to hang it with a hydraulic lift;
• squeeze the handbrake, engage first gear, open the hood;
• Use a Phillips screwdriver to unscrew the two bolts on the decorative plastic overlays in the frill area.

We extract them;

• remove the standard glass stops, external glass seal Lada Granta liftback (sedan);
• in the cabin we remove the front upper trim, rear-view mirror, antenna transmitter, and other equipment installed on the glass;
• in the upper part, carefully pry up the rubber moldings - seals;
• Use a string to cut the rubber layer between the glass and the body, remove the glass using special vacuum suction cups;
• We clean the surface from any remaining rubber coating. For these purposes we use a scalpel, a stationery knife;
• degrease the new glass, apply primer and special glue along the edge;
• the landing site on the hull is also subject to primer treatment;
• Together with a partner, we apply glass, align the gaps on each side, install stops;
• wait 15 - 20 minutes for the glue to set, put on moldings, decorative inserts, windshield wipers;
• In the cabin we complete the installation, fix the rear view mirror and antenna transmitter.

Replacing the windshield of a Lada Granta with your own hands is completed. Provided there are no mechanical damage, body deformation, or frontal impacts, the service life is unlimited.

Rear window

The process of replacing the rear one is similar in sequence to the previous one. The only difference is in the size of the product, and the locking mechanism is completely identical. Replacing the windshield on a Granta liftback is somewhat simplified, since it is not necessary to dismantle part of the rear trim, as is the case in a classic sedan. In all other respects the similarity.

Side windows

Products can also be removed from doorways without much effort. It is necessary to first dismantle the door trim, sound insulation, control unit, electrical wiring package, and guides.

Defects requiring replacement

For car windshields on Granta, standard triplex is used, two layers of 2 mm tempered M1 glass are pressed with polyvinyl butyral (PVB) film, the minimum thickness of the windshield is 4 mm. When hit by a stone that flies out from under the wheels of the vehicle in front at a speed of more than 80 km/h, a deep chip is formed, and cracks spread throughout the area due to vibration. If such damage occurs, the part must be replaced. Replacement will also be required in other cases where there is no direct impact of gravel. These include:

1. Significant wear on the windshield, reducing visibility by more than 15%.
2. A crack that goes from edge to edge. Appears if there is a violation of the geometry due to body deformation.
3. Deep scratches that cannot be repaired, polished or varnished.

Original windshields are installed at the manufacturer's factory, and the part is marked with a barcode with information about the brand, production date, batch number, etc. When choosing a replica, it is recommended to give preference to products from trusted brands.

According to the rules, each manufacturer can put its marking in any place, most often it is the lower right or upper corner on the passenger side.

Glass selection

In addition to the SLGLASS company, licensed Lada Granta glass is produced by the following manufacturers:

1. Bor (RF);
2. BENSON (PRC) – for models after 2011, a rain sensor is provided;
3. SAT;
4. AGC.

When choosing a windshield from manufacturers of licensed replicas, you need to pay attention to the clarity of the silk-screen printing, the presence of a window for the VIN code, the transparency of the glass and cleanliness. The manufacturer labels products not according to GOST, but according to accepted international labeling standards. Glass number in the catalog for various configurations of the Lada Granta:

1. VAZ 2190 - 2190-5206016-05, size 1405x959 mm.
2. Lada Granta liftback, sedan - 2190 SED 4D 2 2011.
3. VAZ Granata 2190 5D HB 2013 - number for five-door hatchbacks.

The dimensions of the windshield are the same for all Grant models; the “Lux” configuration option includes the installation of heated windshield around the perimeter and in the area of ​​the wipers, and the presence of a rain sensor. The cost of a replica with additional equipment is from 3,500 rubles. The average price of an original windshield for August 2022 is 2,400 rubles.

The process of replacing a part is not complicated or expensive; reinstallation can be done independently, with a minimum of equipment. Replacing windshields on all VAZ Granta models is carried out similarly, according to a template.

Owner reviews about glass quality

Replacing the trunk lid glass of a Granta liftback sedan yourself is not at all difficult, no special equipment is needed, with the exception of a string. In all other respects, the process is intuitive; if difficulties arise, you can always read the instructions, video materials, or visit a service station for consultation.

Once a split has formed, do not delay repairs. Reduced visibility on the road increases the accident rate and slows down the driver's reaction.

Technical equipment

The car is equipped with two engine options. Both comply with Euro 4

The standard engine is a conventional eight-valve, four-cylinder 1.6-liter petrol engine, which at 5100 rpm can develop 87 hp. Only a mechanical five-speed gearbox is installed on such an engine. In this case, the car will accelerate to hundreds in 12.4 seconds and reach a speed of no more than 165 km/h. In mixed mode, the manufacturer claims a consumption of 7 liters per hundred.

Much more interesting is the 16-valve engine with electronic fuel supply and supercharging, with the same volume of 1.6 liters. Such a power unit will produce 106 “horses” at 5800 rpm, which will accelerate on the “handle” in a little less than 11 seconds, while showing a speed of 180 km/h in ideal conditions. A “robot” is also installed on such engines. This slightly slows down the acceleration time, but, compared to manual transmission, it reduces fuel consumption. If you wish, you can try to achieve no more than 6.5 liters in mixed mode. Previously, Japanese “four-speed” ones were installed, but, surprisingly, the “robots” from ZF turned out to be cheaper and better adapted to our conditions, so AVTOVAZ completely abandoned the Japanese Jatco and made the right decision. In general, in recent years the plant has shown itself exclusively on the positive side, which cannot but rejoice.